Roto E-Tec. Electronic drive and control systems for windows and doors. Installation instructions for detachable miniature cable junctions

Size: px

Start display at page:

Download "Roto E-Tec. Electronic drive and control systems for windows and doors. Installation instructions for detachable miniature cable junctions"

Teresa Anne Walters
6 years ago
Views:

1 Roto E-Tec Electronic drive and control systems for windows and doors Installation instructions for detachable miniature cable junctions

2 Liability exclusion All specifications in this brochure were diligently compiled and validated. Changes due to technical progress, changes in legislation and the passage of time are unavoidable. We therefore hope you understand that we cannot be held liable for the accuracy or completeness of the contents. All rights, in particular the right to copy and circulate, reserved. Imprint Copyright: July 2012 Roto Frank AG Wilhelm-Frank-Platz 1 D Leinfelden-Echterdingen Telephone: Telefax: info@roto-frank.com

3 Contents Information on the product Detachable miniature cable junction... 4 Technical specifications...5 Detachable miniature cable junction with alarm-glass connection socket... 6 Technical specifications...7 Scope of delivery... 8 Dimensions... 9 Mounting Advice Preparation for mounting Cable junction Determining connection assignment Detachable miniature cable junction with alarm-glass connection socket...14 Dismantling Accessories Cover plates, mounting box Dimensions & delivery scope...17 Installation drawings for cover plates Installation drawings for mounting box Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

Information on the product Detachable miniature cable junction 6-pin, detachable connector Moulded-on cable Window rebate installation Due to its compact dimensions, the model M 13 34 cable junction

4 Information on the product Detachable miniature cable junction 6-pin, detachable connector Moulded-on cable Window rebate installation Due to its compact dimensions, the model M cable junction ( ) can be installed concealed in the window and balcony door rebate without additional milling. After loosening the locking screw and disconnecting the integrated, 6-pin connector, the window/door can be removed. The cable is moulded onto the cable junction pieces on the socket and plug side. 4. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

5 Information on the product Detachable miniature cable junction Technical specifications Technical specifications Cable LiF9Y11Y 6-pin version 4.9 mm dia., grey 6 wires: 0.34 mm 2, red, blue, white, brown, green and yellow Max. 3.0 A current load Cable length on socket side 4 m Cable length on plug side Protection type in accordance with DIN Max. voltage 6 m IP 67 (when plugged in) 48 V DC Temperature range when moving -5 C to + 50 C at rest -25 C to + 70 C LIYY 6 x 0.34 mm 2 Fig.: Block diagram of socket LIYY 6 x 0.34 mm 2 Fig.: Block diagram of plug Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

Information on the product Detachable miniature cable junction with alarm-glass connection socket Detachable connector Suitable for alarm glass Protection class IP 67 The model M 13 40 (619 587)

6 Information on the product Detachable miniature cable junction with alarm-glass connection socket Detachable connector Suitable for alarm glass Protection class IP 67 The model M ( ) detachable cable junction is used to cover the transition from supply lines in the window or balcony door rebate. The simple disconnection of the cable junction via the connector in the rebate area enables the sash to be removed. The minimal space requirement permits installation at many points in the rebate area. With the window closed, concealed installation in the window rebate prevents access to the cable junction. And the integrated tamper circuit (opening monitoring ) enables monitoring of the plugged-in connection. Opening of the connector is signalled by the alarm control panel. In addition, the connector is also mechanically fixed in place with a screw. With the alarm-glass connection socket (AGV) at the other end of the cable of the cable junction, alarm glasses can be connected directly to the cable junction. 6. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

7 Information on the product Detachable miniature cable junction with alarm-glass connection socket Technical specifications Technical specifications Cable plug LiF9Y11Y 6 x 0.14 mm mm dia., white Cable socket LiY11Y 4 x 0.14 mm mm dia., white Cable length on socket side, outside of spiral 0.33 m Cable length on plug side 6 m Protection type in accordance with DIN IP 67 (when plugged in) Max. voltage 48 V DC Max. current 0.5 A Temperature range when moving -5 C to + 50 C at rest -25 C to + 70 C Environmental grade in accordance with VdS 2110 III VdS approval number G Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

8 Information on the product Scope of delivery Delivery scope of model M detachable miniature cable junction (mat. no ) 6-pin plug unit in PVC housing moulded with connection cable 6-pin socket unit in PVC housing moulded with assembled VA metal spring and connection cable End piece for installation of the VA metal spring 4 each A2 fastening screws, DIN 7982 (2.9 x 19 mm) Installation instructions Delivery scope of detachable miniature cable junction with alarm-glass connector Model M (mat. no ) 6-pin plug unit in PVC housing moulded with connection cable 6-pin socket unit in PVC housing moulded with assembled VA metal spring and connection cable with AGV socket End piece for installation of the VA metal spring 4 each A2 fastening screws, DIN 7982 (2.9 x 19 mm) Installation instructions 8. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

9 Information on the product Dimensions Ø 7.5 Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

10 Mounting Advice Due to the large number of profiles and hardware available on the market, no generally applicable information on mounting can be provided, as these systems differ in several dimensions. Please check the mounting location and the available space in the rebate area before the start of mounting. Mounting location: Window or balcony door rebate The operation of the connector is restricted to a maximum of 10 plugging cycles. Avoid torsion (cable twist) over the entire length of the cable, especially in the metal spring. The connector has an anti-twist protection against the danger of polarity reversal ; nevertheless the correct polarity must be ensured prior to each plugging cycle. The connector must never be operated when soiled or damp. 7 mm dia. drilled holes for cable routing. Deburr drilled holes and check for chips. In addition to the generally valid state of technology, particular attention must be paid to the following sets of technical rules: VDS 2311, VDE 0100 NOTE! Install the detachable U-shaped cable junction (see fig.) so that the sash can be turned open far enough (> 90 ). NOTE! Leave a cable loop on the permanently mounted end of the spiral (not the plug end). This ensures that the cable in the cable junction has sufficient freedom of movement if necessary when the window or the door is opened. 10. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

11 Mounting Preparation for mounting 1. 7 mm dia. hole through the frame 2. Mill elongated hole (6 x 21 mm) through the hardware groove up to the glazing rebate. Sash component Frame component Ø NOTE! With timber windows, it may be necessary to create a pocket for fastening the cable junction in order to enlarge the installation space in the rebate. NOTE! The drilling holes must be free of burrs and chips. Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

12 Mounting Cable junction 1. Guide the cable through the frame. 2. Fasten plug end with screw 1. 1 Fig.: Mounting on plug end 3. Guide the cable with the end for the alarm glass through the sash. 4. Fix the end of the spring in place in the fastening strip and fasten it with the screws 2 and 3 in the hardware groove. 2 3 Fig.: Mounting fastening strip NOTE! Only screw in screws by hand. Pre-drilling of the screw holes is recommended. 12. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

13 Mounting Cable junction 5. Hinge the sash and produce the plug-and-socket connections. NOTE! Watch the anti-twist protection of the connector! Insulate the wires of the cable not used! Fig.: Mounting connector 6. Secure the connector with the screw 4. 4 Fig.: Mounted cable junction NOTE! Only screw in screws by hand. Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

14 Mounting Determining connection assignment Detachable miniature cable junction with alarm-glass connection socket NOTE! To determine the connection assignment, the cable junction must not be connected to either the alarm-glass connection socket or the loose end of the cable. Determine the connection assignment: Mount the cable junction; this closes the tamper circuit. Determine the corresponding wires of the tamper circuit on the loose end of the cable with the circuit continuity tester/resistance tester (measured value approximately 0 Ω) and mark (e.g. by twisting). For easier measuring, bridge the two centre contacts of the alarm-glass connection socket Determine the corresponding wires on the loose end of the cable (measured value approximately 0 Ω) with the circuit continuity tester/resistance tester and mark; these form the peak connection. The two remaining wires form the signal line. Remove the bridge at the alarm-glass connection socket. Loose end of cable Alarm-glass connection socket Peak connection Signal line Alarm system Tamper circuit 14. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

15 Mounting Dismantling 1. Loosen screw 4 and remove. 2. Separate connector with Allen key or suitable screwdriver. NOTE! Do not pull on the spring to separate the connector. Otherwise the spring will be damaged. 4 Fig.: Dismantling 3. Remove the sash. 4. Protect connector against dust and moisture. Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

Accessories Cover plates, mounting box The stainless-steel accessories with a brushed surface were developed especially for installation of detachable miniature cable junctions in timber, PVC and

With timber windows and balcony doors, an oblong hole (see page 18 for dimensions) must be milled.

16 Accessories Cover plates, mounting box The stainless-steel accessories with a brushed surface were developed especially for installation of detachable miniature cable junctions in timber, PVC and aluminium windows and balcony doors. Cover plates For timber (mat. no ) For PVC and aluminium (mat. no ) The cover plates are used to cover milled areas and drilled holes. With timber windows and balcony doors, an oblong hole (see page 18 for dimensions) must be milled. With PVC windows and balcony doors, the cover plate fits in the standardised profiles of popular suppliers. Mounting box Mat. no The mounting box is used to provide sufficient space for the cable junction if the clearance is not sufficient. Prior to installation including the cable junction, a pocket (see page 19 for dimensions) must be milled. 16. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

17 Accessories Cover plates, mounting box Dimensions & delivery scope Cover plate for timber Cover plate for PVC, aluminium Mounting box Installation accessories Description Mat. no. Material Dimensions (W x H x D) Scope of delivery Cover plate for timber Stainless steel Cover plate for PVC, aluminium Stainless steel Mounting box Stainless steel 16 x 126 x 3 mm 1 cover plate 2 screws, M 3 x 12 mm 2 screws, 3.5 x 25 mm 16 x 126 x 3 mm 1 cover plate 2 screws, M 3 x 12 mm 2 screws, M 4 x 6 mm 2 screws, 3.5 x 25 mm 20 x 180 x 25 mm 1 mounting box 2 screws, M 3 x 12 mm 2 screws, M 4 x 6 mm 2 screws, 3.5 x 25 mm Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

18 Accessories Installation drawings for cover plates Cover plate for timber Depth 3 mm Cover plate for PVC, aluminium 18. July IMO_229_EN_v0 Roto E-Tec Cable junctions Subject to change.

19 Accessories Installation drawings for mounting box Mounting box for timber Depth 30 mm Depth 1 mm Mounting box for PVC, aluminium Depth 30 mm Subject to change. Roto E-Tec Cable junctions IMO_229_EN_v0. July

20 Roto Frank AG Window and door technology Wilhelm-Frank-Platz 1 D Leinfelden-Echterdingen Telephone Telefax info@roto-frank.com MTS / textract Dated: July Subject to change. IMO_229_EN_v Roto Frank AG Roto is a registered trademark From a single source: The optimum hardware system to meet all challenges Roto E-Tec Electronic drive and control systems for windows and doors Roto NT The world s biggest selling Tilt&Turn hardware system for windows and balcony doors Roto Patio Hardware systems for large sliding windows and doors

Roto E-Tec Control Contacts for Security Engineering and Room Climate

Roto E-Tec Control Contacts for Security Engineering and Room Climate Window and door technology Roto E-Tec Control s for Security Engineering and Room Climate Installation, maintenance and operating instructions for Roto E-Tec Control MVS and MTS Imprint Copyright: October