DEVKIT-MPC5744P QUICK START GUIDE (QSG) Ultra-Reliable MCUs for Industrial and Automotive Applications. EXTERNAL USE

Transcription

1 DEVKIT-MPC5744P QUICK START GUIDE (QSG) Ultra-Reliable MCUs for Industrial and Automotive Applications

2 Contents Quick Start Package Overview Step-by-Step Installation Instructions Hardware: DEVKIT-MPC5744P Board Features Overview Pinout and Jumper Settings Power Supply Software: Software Development Tools Pre-compiled Code Examples Documentation MPC574xP Family : Phantom Feature Differences OpenSDA Recommendations 1

3 Quick Start Package Overview Board: DEVKIT-MPC5744P Low cost EVB with MPC5744P Auto quality MCU on board Documents: Name Quick Start Guide(QSG) Software Installation Guide(SWIG) Application Notes Fact Sheets, Reference Manuals and Data Sheets Description Detailed description on availability of Hardware, Software and Documents to quick start with MPC5744P project (this document) Detailed walk through on how to install and use S32 Design Studio for Power Architecture Detailed documents covering topics from how to design hardware to how to write software Detailed manuals for MPC5744P family of MCU and DEVKIT-MPC5744P board Downloads: Name Integrated Development Environment (IDE) DEVKIT-MPC5744P Quick Start Package DEVKIT-MPC5744P Schematics DEVKIT-MPC5744P PCB Design Package Description Eclipse based S32DS IDE with free GCC compiler and Debugger support Software examples and supporting documents for getting started with the DEVKIT-MPC5744P PDF schematic files for the DEVKIT-MPC5744P board Gerber files and Bill of Material 2

4 Step-by-Step Installation Instructions In this quick start guide, you will learn how to set up the DEVKIT-MPC5744P board and run the default program. 1 Install Software and Tools Install S32 Design Studio IDE for Power Architecture. S32 Design Studio for Power See Software Installation Guide (SWIG) for detailed procedure 2 Connect the USB Cable Connect one end of the USB cable to the PC and the other end to the micro-b connector on the DEVKIT-MPC5744P board. Allow the PC to automatically configure the USB drivers. 3 Observe the Default Program reaction The pre-loaded example project utilizes the DEVKIT-MPC5744P user potentiometer and the user LEDs. Once the board is plugged in the ADC will scan the potentiometer result and shine LEDs based on result. Turn the potentiometer to turn on a different LED pattern. (Clock is configured to PLL running at 160 MHz) Learn More About the DEVKIT-MPC5744P 4 Read release notes and documentation on the nxp.com/devkit-mpc5744p nxp.com/mpc5744p 3

5 DEVKIT-MPC5744P Board : Features MPC5744P has 2 x 200 MHz Power Architecture e200z4 Dual issue cores operating in delayed lockstep MPC5744P qualified to AEC-Q100 Grade 1 and ambient temperature of -40 to +125 C Arduino UNO R3 footprint-compatible with expansion shield support Supports DEVKIT-MOTORGD motor control shield Integrated Open-standard Serial and Debug Adapter (OpenSDA) with support for several industry-standard debug interfaces as well as JTAG connector Easy access to the MCU I/O header pins for prototyping On-chip connectivity for FlexRay, CAN, LIN, UART/SCI and SPI Potentiometer for precise voltage and analog measurement One user RGB LED (1 red, 1 green, 1 blue in single package) 2 user push-button switches Flexible power supply options micro-b USB 12V External power supply Similar hardware across ARM, S12 and Power Architecture architecture based MCUs Box includes: DEVKIT-MPC5744P Board Downloads includes: Quick Start Package S32 Design Studio IDE Application notes NOTE: DEVKIT-MPC5744P RevB does not support shield reset. Any Arduino shield that relies on reset signal from DEVKIT-MPC5744P RevB will not work. Shield reset is supported starting with RevC. 4

6 DEVKIT-MPC5744P Board : Overview JTAG OpenSDA MCU NXP Microcontroller MPC5744P The DEVKIT-MPC5744P is an ultra-low-cost development platform for MPC5744P Microcontrollers. Reset Button J2 J1 J6 Potentiometer 5 Features include easy access to all MCU I/Os, a standard-based form factor compatible with the Arduino pin layout, providing a broad range of expansion board options, and a USB serial port interface for connection to the IDE. The board has option to be powered via USB or an external power supply. CAN Bus LIN Bus 12V External Power Supply JTAG MPC5744P J3 J4 J5 OpenSDA MCU OpenSDA MCU Boot Entry Button FlexRay User Switch 1 User Switch 2 OpenSDA micro-usb User LEDs

7 DEVKIT-MPC5744P Board : Pinout 1 of 3 FUNCTION PORT PIN PIN PORT FUNCTION LT_PA15 J2-19 J2-20 PA15 CAN1_RXD LT_PA9 J2-17 J2-18 PA14 CAN1_TXD NC J2-15 J2-16 PB3 LIN0_RXD GND J2-13 J2-14 PB2 LIN0_TXD DSPI0_SCK LT_PC5 J2-11 J2-12 PD10 FLEXPWM_0_A0 J2 DSPI0_SIN DSPI0_SOUT LT_PC7 LT_PC6 J2-09 J2-07 J2-10 J2-08 PD4 PD3 FLEXPWM_0_B3 FLEXPWM_0_A3 DSPI0_CS0 LT_PC4 J2-05 J2-06 PE11 LT_PG7 J2-03 J2-04 PC14 LT_PD2 J2-01 J2-02 PC10 J1 FUNCTION PORT PIN PIN PORT FUNCTION LT_PA13 J1-15 J1-16 PB6 CLKOUT LT_PA12 J1-13 J1-14 PE7 ETIMER_0_ETC3 LT_PD14 J1-11 J1-12 PA8 ETIMER_2_ETC4 ETIMER_0_ETC2 LT_PF0 J1-09 J1-10 PA7 ETIMER_2_ETC3 FLEXPWM_0_B0 LT_PA10 J1-07 J1-08 PA6 ETIMER_2_ETC2 FLEXPWM_0_A0 LT_PA11 J1-05 J1-06 PA5 ETIMER_1_ETC5 FLEXPWM_0_X0 LT_PD9 J1-03 J1-04 PA4 ETIMER_0_ETC4 LT_PD12 J1-01 J1-02 PA3 ETIMER_0_ETC3 J2 J1 6 Arduino Compatibility The internal rows of the I/O headers on the DEVKIT-MPC5744P are arranged to fulfill Arduino shields compatibility.

8 DEVKIT-MPC5744P Board : Pinout 2 of 3 J3 J3 FUNCTION PORT PIN PIN PORT FUNCTION PD12 J3-02 J3-01 EXT_HV_PWR 12V_IN PD9 J3-04 J3-03 EXT_LV_PWR 3.3V or 5V Selectable PJ8 J3-06 J3-05 RESET MPC5744P Reset PE13 J3-08 J3-07 3V3_SR 3.3V PE14 J3-10 J3-09 5V0_SR 5V PE15 J3-12 J3-11 GND PF14 J3-14 J3-13 GND PF15 J3-16 J3-15 EXT_HV_PWR 12V_IN J4 J4 FUNCTION PORT PIN PIN PORT FUNCTION PE0 J4-02 J4-01 PB8 ADC0_AN1 PE6 J4-04 J4-03 PB12 ADC0_ADC1_AN14 PG2 J4-06 J4-05 PB9 ADC0_ADC1_AN11 PG3 J4-08 J4-07 PB10 ADC0_ADC1_AN12 PG4 J4-10 J4-09 PB11 ADC0_ADC1_AN13 PG5 J4-12 J4-11 PB7 ADC0_AN0 PG6 J4-14 J4-13 PB13 ADC1_AN0 PD11 J4-16 J4-15 PJ9 ETIMER_2_ETC5 7 Arduino Compatibility The internal rows of the I/O headers on the DEVKIT-MPC5744P are arranged to fulfill Arduino shields compatibility.

9 DEVKIT-MPC5744P Board : Pinout 3 of 3 J6 FUNCTION PORT PIN PIN PORT FUNCTION PF12 J6-19 J6-20 PE5 PF13 J6-17 J6-18 PE4 PC6 J6-15 J6-16 PE0 PC7 J6-13 J6-14 PE1 PI2 J6-11 J6-12 GND PI3 J6-09 J6-10 PER_HVA PH3 J6-07 J6-08 PC11 PH4 J6-05 J6-06 PC10 PG3 J6-03 J6-04 PG5 PG2 J6-01 J6-02 PG4 J5 J6 J5 FUNCTION PORT PIN PIN PORT FUNCTION PD5 J5-2 J5-1 PA0 PD6 J5-4 J5-3 PA1 PD7 J5-6 J5-5 PA2 PD8 J5-8 J5-7 PG8 3.3V 3V3_SR J5-10 J5-9 PF3 GND J5-12 J5-11 PG11 PC1 J5-14 J5-13 PG9 PE4 J5-16 J5-15 PE2 PC2 J5-18 J5-17 PE5 PB14 J5-20 J5-19 PG10 8 Arduino Compatibility The internal rows of the I/O headers on the DEVKIT-MPC5744P are arranged to fulfill Arduino shields compatibility.

10 DEVKIT-MPC5744P Board : Jumper Settings There is only one jumper: J13 It is to select Power source: 1-2: External 12 V Supply 2-3: Default USB powered 5V Supply, through OpenSDA interface 3 1 J13 9 Note: For high power/current consuming applications (like using external shield boards) use External 12 V Supply only

11 DEVKIT-MPC5744P Board : Communication Interfaces CAN_0 DESCRIPTION NAME PIN Port PB0 & PB1 CANH P5-01 CANL P5-02 NC P5-03 GND P5-04 LIN_0 DESCRIPTION NAME PIN GND P6-01 GND P6-02 Connect to 12V VSUP P6-03 Port PB2 & PB3 LIN P6-04 CAN LIN FlexRay FlexRay_A DESCRIPTION NAME PIN FRA-DATA-A P4_1 FRA-DATA-B P4_2 FlexRay_A DESCRIPTION PORT FR_A_TX PD0 FR_A_TX_EN PC15 FR_A_RX PD1 10

12 DEVKIT-MPC5744P Board : User Peripherals Reset Button User LEDs Potentiometer User Switch 1 User Switch 2 DESCRIPTION PIN PORT Potentiometer (ADC1_AN6) RV1/POT PE12 User Switch 1 SW1 PF12 User Switch 2 SW2 PF13 User LEDs PC11 D7 PC12 PC13 Reset Button SW3 11

13 DEVKIT-MPC5744P Board : Programing Interface JTAG JTAG DESCRIPTION Support for USB Multilink Interface PIN P2 OpenSDA MCU Boot Entry Button OpenSDA JTAG OpenSDA MCU OpenSDA micro USB OpenSDA Interface DESCRIPTION OpenSDA MCU Boot Entry SW4 OpenSDA micro USB: On-board JTAG connection via open source J12 OSBDM circuit using the MK20DX128VFM5 Microcontroller OpenSDA JTAG: JTAG to update firmware in J11 OpenSDA MCU PIN 12

14 Package Level Pinout Diagram MPC5744P (144 LQFP) 13

15 DEVKIT-MPC5744P Board : Power Supply JTAG OpenSDA MCU Boot Entry Button OpenSDA JTAG OpenSDA MCU OpenSDA micro USB DEVKIT-MPC5744P supports power through OpenSDA (USB) and external 12V power supply. NXP does not directly sell 12V power supplies. You can obtain a power supply through a third-party. Power supply specifications: Fully regulated Switching Power Supply Input Voltage V AC 50/60Hz Output 12V 1A/2A DC Plug size: 5.5mm x 2.1 mm, Center Positive 12V must be used for CAN and LIN/UART communication. 14

16 Software Development Tools S32 Design Studio IDE for Power Architecture IDE & Compilers Free S32 Design Studio IDE with GCC compiler GHS MULTI Integrated Development Environment Cosmic IDE isystems winidea IDE Sourcery TM CodeBench Development Tools Debuggers Free OpenSDA debugger on board and supported by S32DS IDE P&E USB Multilink isystems ic6000 Lauterbach TRACE32 JTAG Debugger 15

17 Pre-Compiled Code Examples Pre-compiled example projects are available in S32DS as well as on nxp.com/devkit-mpc5744p for quick start Example projects also includes the projects from Application Note, AN4830: Qorivva Recipes for MPC574xG, migrated to MPC5744P platform List of code examples: 1. Hello World 2. Hello World + PLL 3. Hello World + PLL + Interrupts 4. ADC 5. etimer Frequency Measurement 6. etimer Count 7. Flash ECC 8. FlexCAN 11. LIN Master 12. LIN Slave 13. UART 14. SPI 15. SPI+DMA 16. TSENS 17. XBIC+DMA 18. SGEN + FlexPWM 19. Low Power STOP 20. Register Protection 21. FCCU 16

18 Documentation and Reference Material Documentation Links MPC574xP Datasheet MPC574xP Product Brief MPC574xP Factsheet Application Notes MPC5744P Startup Self Test Control Unit (STCU) Overview MPC574xP Hardware Design Guide Migrating from MPC5743L to MPC5744P MPC5744P Standard 144 LQFP EVB User Guide MPC5744P Standard 257 BGA EVB User Guide MPC5744P Clock Calculator Guide Reference Manuals MPC574xP Family Reference Manual MPC574xP Family Safety Manual 17

19 MPC574xP Family Phantom Feature Differences FEATURES MCU Flash* RAM EE PROM Packages MPC5744P 2.5MB 384K Emulate 144 LQFP/ 257 MAPBGA MPC5743P 2.0MB 256K Emulate MPC5742P 1.5MB 192K Emulate MPC5741P 1.0MB 128K Emulate 144 LQFP/ 257 MAPBGA 144 LQFP/ 257 MAPBGA 144 LQFP/ 257 MAPBGA Available in NXP DEVKIT platform *Differences in memory are all in the Large Flash Block 18

20 MPC574xP Family Package Feature Set Comparison MPC574xP Package FEATURES FREQ FlexCAN ENET DSPI FlexPWM etimer PIT ADC LinFlexD edma CTU Zipwire FlexRay GPI GPIO 144 LQFP 4.76 MHz to 200 MHz 3 No 3 2 1) 3 2) 1 4 x 12 bit x 16 ch 3) 2 32 ch 2 4) No MAPMGA 4.76 MHz to 200 MHz 3 Yes x 12 bit x16 ch 3) 2 32 ch 2 Yes ) FlexPWM1 has available only A[0-2] and B[0-2] external signals. 2) etimer2 has available only ETC2-5 external signals. 3) There are 38 ADC channels which include internal channels (temperature sensors, bandgap voltage) and shared channels. 4) CTU1 has not external trigger output. Available in NXP DEVKIT platform 19

21 OpenSDA 1 of 2 OpenSDA is an open-standard serial and debug adapter It bridges serial and debug communications between a USB host and an embedded target processor DEVKIT-MPC5744P comes with the OpenSDA Application preinstalled Follow these instructions to run the OpenSDA Bootloader and update or change the installed OpenSDA Application Enter OpenSDA Bootloader Mode 1. Unplug the OpenSDA USB cable if attached 2. Press and hold the Bootloader Entry button (SW4) 3. Plug in a USB cable between a USB host and the OpenSDA USB 20 connector (labeled SDA ) 4. Release the Reset button A removable drive should now be visible in the host file system with a volume label of BOOTLOADER. You are now in OpenSDA Bootloader mode. IMPORTANT NOTE: Follow the Load an OpenSDA Application instructions to update the application on your MK20DX128VFM5 to the latest version. It is likely that the version provided in this package is newer than what was preprogrammed on your MK20DX128VFM5. Load an OpenSDA Application 1. While in OpenSDA Bootloader mode, double-click SDA_INFO.HTML in the BOOTLOADER drive. A web browser will open the OpenSDA homepage containing the name and version of the installed Application. This information can also be read as text directly from SDA_INFO.HTML 2. Locate the OpenSDA Applications folder 3. Copy & paste or drag & drop the Application to the BOOTLOADER drive 4. Unplug the USB cable and plug it in again. The new OpenSDA Application should now be running and check the latest version by repeating Step-1 Use the same procedure to load other OpenSDA Applications.

22 OpenSDA 2 of 2 Using the Virtual Serial Port 1. Determine the symbolic name assigned to the DEVKIT-MPC5744P virtual serial port. On Windows platform open Device Manager and look for the COM port named OpenSDA-CDC Serial Port. 2. Open the serial terminal emulation program of your choice. Examples for Windows platform include Tera Term, PuTTY, or HyperTerminal. 3. Program one of the code examples using S32 Design Studio IDE. 4. Configure the terminal emulation program. Most embedded examples use 8 data bits, no parity bits, and one stop bit (8-N-1). Match the baud rate to the selected serial test application and open the port. 5. Press and release the Reset button (SW3) at anytime to restart the example application. Resetting the embedded application will not affect the connection of the virtual serial port to the terminal program. NOTE: Refer to the OpenSDA User s Guide for a description of a known Windows issue when disconnecting a virtual serial port while the COM port is in use. 21

23 Recommendations For faster debugging, debug from RAM, because this cuts down the lengthy Flash erase operation cycles. Follow the Software Integration Guide (SWIG) for details. By default New Project in S32 Design Studio IDE makes application to run at 16 MHz Internal RC (IRC) oscillator. For faster performance, configure PLL to desired frequency and switch clock source to PLL before executing application code. Keep S32 Design Studio IDE and OpenSDA firmware Up-to-date for best results Post Technical Questions on NXP community for MPC5xxx. Useful Links: MPC5744P Webpage nxp.com/devkit-mpc5744p nxp.com/s32ds nxp.com/community 22

24