MLM WALL CONTROLLER OPERATING MANUAL
|
|
- Primrose Adams
- 6 years ago
- Views:
Transcription
1 MLM WALL CONTROLLER OPERATING MANUAL PUBLICATION /1
2 INTRODUCTION This Remote Digital Wall Mounted Thermostat/Controller is fitted with a Room Sensor and LCD display. The Thermostat/Controller is supplied in an aesthetically pleasing, compact 80mm by 82mm plastic enclosure. The unit provides for Setpoint Temperature adjustment and Room Temperature display. Further advanced functionality is available for commissioning and set-up purposes. The unit is designed to mount into a round draw-box. The MLM wall controller is designed to work in conjunction with Rickard PC based software for further functionality. OPERATOR PANEL GENERAL LAYOUT LCD SCREEN UP DOWN FUNCTION ENTER / ACCEPT 2007/12-2
3 GENERAL ROOM OPERATION 1) On start-up (power on), the following screen will be displayed. The software initiates and communicates with all other controllers and interface boards connected on the same circuit. Previously stored information is collected from all controllers and interface boards. The software version number is displayed while the software initiates. 2) Diffuser limit detection: After software initiation the diffuser will drive to the fully closed position. During this process the limit indicators on the display will flash and the direction arrow will show that the diffuser is driving closed. When the motor drives into the end stop, the software will remember that position as the fully closed position. 3) Control mode: After limits are detected, the controller will enter control mode. Room temperature is displayed. The letters Cr indicates Remote Wall Controller temperature as Source for display. When CO is displayed the Source for display is the Onboard sensor. CE is displayed to indicate Control Temperature Error. Wall stat temperature is displayed, but no temperature is selected for control purposes. The controller will now drive the diffuser open towards the position required to get room conditions under control. In picture 1 the display indicates that cooling mode is required to get room conditions under control and the diffuser is busy driving open. In this mode Room temperature is displayed. If Room temperature was colder than set-point, heating mode would have been required to get room conditions under control. PICTURE 1 COOLING MODE INDICATOR 2007/12-3
4 Picture 2 indicates the diffuser has reached the fully open position. Picture 3 indicates the diffuser is in heating mode and has reached the minimum stop position for heating. The neck heater is on as displayed. The diffuser could also be in heating mode without the neck heater activated. The heater (if fitted) will only be activated when the control disc reaches the correct position for heating. (Factory set at 30% control disc position) PICTURE 2 PICTURE 3 HEATING MODE INDICATOR RE-HEATING ON INDICATOR 4) Set-point adjustment To adjust the set-point, either the UP or DOWN buttons must be pressed. After one of these buttons have been pressed, the current set-point will be displayed. While in this screen, press either the UP or DOWN button to adjust the set-point value. The value displayed will now flash. Press the ENTER/ACCEPT button to return to control mode with the new set-point applied. The top left two digits will indicate respectively the Source of the set-point and which set-point is Active. If the display shows r1, this indicates the Wall thermostat set-point is the source and set-point 1, ie normal control is active. Should the digits show o2 this indicates an onboard controller is where the setpoint is active and the back-off set-point is active at the current time. 2007/12-4
5 ADVANCED FEATURES 1) Entering Advanced feature mode: Keep the FUNCTION button pressed for 5 seconds until unit Beeps continuously. Release the button and the first advanced feature is displayed. Pressing FUNCTION again to advance to the next feature. 2) Change-over sensing: (Indicated as CO ) When a Supply Air (Change Over) sensor is fitted the supply air temperature will be displayed. When no sensor is fitted, a zero value will be displayed. 3) Room temperature: Wall Thermostat/Controller sensor value is displayed. r indicates source for control purposes is Wall Controller 4) Manual Drive Mode The % control disc opening is displayed. 0% is fully closed. 100% is fully open. dr indicates the unit is in manual drive mode. Select required control disc position with UP or DOWN buttons. Press ENTER to move control disc to selected position. Pressing FUNCTION button deactives manual mode and moves to next feature. 5) Manual Heater Drive Control: The current re-heater output value is displayed as a % of maximum. Ht indicates the unit is in Manual mode. Select required output with UP and DOWN buttons. Press ENTER to activate heater at required level. Pressing FUNCTION button deactives manual mode and moves to next feature. 6) Real Time Clock (RTC): RTC value is displayed. This is for use with Night set-back facility. dx indicates day of the week. x can be anything from 1 to 7. Monday is displayed as 1. To edit the RTC value, press ENTER and the minute display will flash. Select current minutes with UP and DOWN buttons. Press ENTER again and select current hour. ENTER again and select the current day. Press ENTER again to exit the RTC function and advance to next feature. 7) Set-point Temperature This is provided to view other set-point temperatures as described above. Change Over/Supply Air Temperature display Room Temperature Manual Drive Mode Manual Heater Control Real Time Clock Set-point Temperature Page 5
6
THERMOSTAT OPERATING MANUAL. Digital T3SQ-2. Redefine your comfort zone.
THERMOSTAT OPERATING MANUAL Digital T3SQ-2 THERMOSTAT OPERATING MANUAL DIGITAL T3SQ-2 Introduction This Setup module is fitted with an LCD display. The adjuster is supplied in an aesthetically pleasing,
More informationMLM Integration with BMS Network Protocols
MLM Integration with BMS Network Protocols The Master Comms Unit 2 (MCU) serves as a gateway to other BMS protocols such as Lontalk or BACnet. The MCU features four diffuser data channels with a capacity
More informationRDF Series Room Temperature Controllers
Document No. 19-49 RDF Series Room Temperature Controllers Product Description Room Temperature Controllers with LCD for twopipe (with and without an electrical heater) and fourpipe fan coil units. Installation
More informationFunctions. Technical Data. Wireless Room Thermostat
This surface-mounted radio thermostat has been developed to be able to switch electric and conventional heating systems on and off using a set temperature and time. Functions Large display can be clearly
More informationRoom unit with PPS2 interface
1 626 Room unit with PPS2 interface for use with: controllers with a PPS2 interface QAA88.3 Room temperature measurement Key buttons for adjustment of the room temperature setpoint Key buttons for operating
More information7-day room temperature controller
s 2 205 7-day room temperature controller Heating or cooling applications REV24.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationOPERATION MANUAL. Room thermostat EKRTW
OPERATION MANUAL 1 1 2 3 1 2 4 1 2 1 2 3 4 5 6 7 8 11 12 13 14 9 10 15 16 17 18 19 20 21 22 23 2 WARNINGS Never let the thermostat get wet, this may cause an electric shock or fire. Never press the buttons
More informationHome Manager System Model TS40B Wall Display Operating Instructions
4700 Lang Avenue McClellan, CA 95652 1.800.BEUTLER www.beutler.com Home Manager System Provides control for Heating and Air Conditioning Zoning Option SmartVent Option Security System Interface Option
More informationNetworkable Dual Duct VAV Controller Specification and Installation Instructions
Controller Models EVCBM14NIT2S (Master controller / 2 TRIACs) EVCS14N (Slave controller) TRL Series Thermostat TRL24 (Room Sensor: Temp) TRLH24 (Room Sensor: Temp and %RH) TRLG24 (Room Sensor: Temp and
More informationMLM Integration with BMS
DOCUMENT NUMBER: BW0070-3 June 2015 Technopark STELLENBOSCH 7600 June 2015 Table of Contents MLM Integration with BMS... 1 MCU 2 Gateway Overview... 3 Output from BMS... 3 Input to BMS... 4 Zone/Master/Slave
More informationWeekday / weekend room temperature controller
s 2 203 Weekday / weekend room temperature controller Heating applications REV17.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationRoom Temperature Controller with 7-Day Time Switch, LCD and opt. Remote Temperature Sensor
3 036 Room emperature Controller with 7-Day ime Switch, LCD and opt Remote emperature Sensor for heating systems RDE201 2-position control with ON/OFF output for heating Operating modes: normal operation
More informationOEM. Room unit QAA822 with2- wire interface. Building Technologies CLIMATIX TM. For use with Climatix controllers
OEM CLIMATIX TM Room unit QAA822 with2- wire interface For use with Climatix controllers Remote control of air conditioning unit Mandík Measurement of the room temperature Buttons for starting, setting
More informationModel: Available in : Sapphire Black and Glacier White
1 Model: Available in : Sapphire Black and Glacier White 1 Table of Contents Product Image 1 Locking/Unlocking the SmartStat 20 23 Table of Contents 2 Standby/Away Mode Mode 21 24 What is a Programmable
More information7-day room temperature controller
s 2 208 7-day room temperature controller Heating applications REV34.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display and large
More informationRCF-230CTD. Room controller for fan-coil applications with outputs for two thermal or one 3-position actuator or function for an electric heater
revision 03 2012 RCF-230CTD Room controller for fan-coil applications with outputs for two thermal or one 3-position actuator or function for an electric heater RCF-230CTD is a room controller intended
More informationFCU-MULTI Modbus Fan Coil Unit Controller
Product Sheet CT2.61 Controller Type FCU-MULTI FCU-MULTI Modbus Fan Coil Unit Controller FCU-MULTI is completely stand-alone operating room controller designed for room heating, cooling, ventilation, lighting
More informationSemi flush-mounted room temperature controllers with LCD
s 3 077 RDD310 RDE410 Semi flush-mounted room temperature controllers with LCD For heating systems RDD310 RDE410 RDD310 and RDE410 features: Operating voltage AC 230 V 2-position control with On / Off
More informationCommercial Controls. Advanced control for saving time and money
L Connection NetWork Commercial Controls Advanced control for saving time and money The efficient way to control hvac and building operations L Connection Network at a glance: Controls a wide range of
More informationCommunicative heating controller, Ethernet
UC150 Communicative heating controller, Ethernet Summary UC150 is a communicative room heating controller with one PWM output for control of a radiator or electrical heater. It can work autonomously, or
More informationZone Manager INSTALLATION MANUAL 40KMC KMQ QNC QNQ
40KMC------301 40KMQ------301 40QNC------3 40QNQ------3 INSTALLATION MANUAL Installation manual This control system only operates with indoor units of the following models: 40KMC------301 and 40KMQ------301
More informationSystem Controls Suggested Specification
1. Description A. Rooftop Unit Controller The Rooftop Unit Controller shall come equipped with a proportional-integral (PI) controller for accurate temperature control. The rooftop unit controller shall
More informationBaltimore Aircoil Company
Baltimore Aircoil Company VFD Startup Guide TABLE OF CONTENTS: A. Verifying Power and Control Wiring...1 B. Setting the VFD Parameters...2 C. Reentering Startup Wizard After Initial Setup...5 D. Starting
More informationSuitable for a wide range of installations with wall-mount, flush-mount and hand-held remote control options.
TUC03 Configurable Terminal Unit Controller Product Bulletin The TUC03 Configurable Terminal Unit Controller is designed specifically to provide direct digital control of terminal unit applications with
More informationRoom Temperature Controller
3 023 Room Temperature Controller for four-pipe fan coil units RCC30 Outputs for on / off valve actuators Outputs for three-speed fan Control depending on room or return air temperature Operating modes:
More informationINSTRUCTIONS FOR USING THE CONTROL PANEL
DIGIT SED ELECTRONIC CONTROLLER WITH LCD DISPLAY 1.09.370E 10.01.2007 VALLOX These instructions replace and complement the instructions for use and maintenance of the following VALLOX units: VALLOX DIGIT
More informationOnboard Inputs and Outputs. Remote User Interface. Integral LCD User Interface
Product Bulletin: FX06 Field Controller Issue Date: March 2006 FX06 Field Controller The FX06 is a compact field controller in the Facility Explorer range of products. The controller is designed specifically
More informationRoom unit with PPS2 interface
1 641 DESIGO RX Room unit with PPS2 interface for use with: QAX321 devices of the ranges DESIGO RXC, RXB, and RXA (PPS2) DESIGO PX Automation stations 1) devices with a PPS2 interface Room temperature
More informationInstruction Manual HID-2
Specifications HID-2 Amps / Volts requirements 15 amps @ 120 volts Min / Max operating temperature 32 to 120 F Min / Max operating humidity 0-99% RH Time setting Hours, Minutes, Seconds Hi-temp setting
More informationFCU (FREE COOLING UNIT)
FCU (FREE COOLING UNIT) FCU reduces the AC running hours on the telecom site Controller Features: Can control upto two AC and one free cooling unit Temperature control Humidity sensor Structural Features:
More informationDesigo RXA Room controllers without bus communications Range overview. CA2S3880en_ Building Technologies
s Desigo RXA Room controllers without bus communications Range overview CA2S3880en_01 2012-08-30 Building Technologies Desigo TM RXA Room controllers without bus communications Contents Desigo RXA......
More informationDescription. descriptors, makes set-up and monitoring very user friendly.
Description The Meridian CV & CV-EX Control Systems are designed as an alternative to multiple programmable thermostats or expensive building automation systems in facilities that have unitary type, HVAC
More informationModel: Available in : Sapphire Black and Glacier White
Model: Available in : Sapphire Black and Glacier White 1 Table of Contents Product Image 1 Locking/Unlocking the SmartStat 20 Table of Contents 2 Standby/Away Mode 21 What is a Programmable Room Thermostat?
More informationUSER'S GUIDE BARD-LINK TM LC /LC SOLID STATE DUAL UNIT LEAD/LAG CONTROLLER & TEC-EYE HAND-HELD DIAGNOSTIC TOOL
USER'S GUIDE BARD-LINK TM LC1000-100/LC1500-100 SOLID STATE DUAL UNIT LEAD/LAG CONTROLLER & TEC-EYE HAND-HELD DIAGNOSTIC TOOL Bard Manufacturing Company, Inc. Bryan, Ohio 43506 Since 1914...Moving ahead,
More informationModel: Touchpad (TFT) Model: TFT
Model: Touchpad (TFT) Model: TFT 1 Model: Touchpad TFT Table of Contents Set-Up Product Image Table of Contents Installation Procedure Initial Setup Setting the Clock LCD Display My System Locking the
More informationWeekday / weekend room temperature controller
s 2 203 Weekday / weekend room temperature controller Heating applications REV17.. Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationSmart Series. Wall Heater Operations Manual. Save This Manual
Smart Series Wall Heater Operations Manual Models: HT2024SS FSSWH2004 HT1502SS FSSWH1502 240V, 2000W 240V, 2000W 120V, 1500W 120V, 1500W Save This Manual Index Features that are functional... pg. 3 Thermostat
More informationMOD-RI Room Interface Modules with Modbus
Product sheet MOD3.00 Type MOD-RI MOD-RI Room Interface Modules with Modbus The MOD-RI are room interface modules designed to provide room control interface for the building management systems. The MOD-RI
More informationVector 3D printer complete wire list including extruder PWA listing
Vector 3D printer complete wire list including extruder PWA listing Conventions Pin numbering for connectors It is normal practice in print circuit board (PCB) layout to denote pin 1 of a PCB mounted connector
More informationARCTIC AIR DC OLED. Digital Control Operations Manual
ARCTIC AIR DC OLED Digital Control Operations Manual Micro Air Corporation Phone (609) 259-2636 124 Route 526 WWW.Microair.net Allentown NJ 08501 Fax (609) 259-6601 Before you start: 1. Applying power:
More informationRCF-230CD. Communicating room thermostat for fan-coil applications with on/off outputs
revision 11 2013 RCF-230CD Communicating room thermostat for fan-coil applications with on/off outputs RCF-230CD intended to control heating and/or cooling in 2- or 4-pipe installations. Setpoint and fan
More informationZONETOUCH DAMPER CONTROL SYSTEM Operation Manual
ZONETOUCH DAMPER CONTROL SYSTEM Operation Manual www.zonemaster.com.au www.polyaire.com.au 2012 Polyaire Pty Ltd TABLE OF CONTENTS 1) Features 2 2) Wall Controller Layout (Touchpad) 2 3) Manual On/Off
More informationEMO valve drive. 1. Function 1. Table of Contents. 2. Installation
Chapter 13: Devices for single room heating 13.2 Valve drives EMO valve drive Art. no. 639119 EMO valve drive EMO valve drivechapter 13:Devices for single room heatingart. no.639119as at 08/0213.2Valve
More informationIS-ZW-RC-1 Remote Control Installation Sheet
GE Security IS-ZW-RC-1 Remote Control Installation Sheet Description Z-Wave technology is designed to automate lighting/home control and provides easy remote operation of all your Z-Wave enabled devices.
More informationRoomMaster ABR-2. Commissioning
Commissioning Content GENERAL Locking of operating mode keys...3 Control panel...3 Function of operating mode keys, operating menu...3 Activation of setting keys...4 Locking of setting keys...4 Setting
More informationUC102 basic version with display and knob UC102BL version with display, knob and backlight UC102DK version without knob and display
UC102 Communicative heating controller Summary UC102 is a communicative room heating controller with two inputs and one PWM output for control of a radiator or electrical heater. It can work autonomously,
More informationUSER S MANUAL. DAS-G01 The Power of Tomorrow
USER S MANUAL DAS-G01 The Power of Tomorrow Richmond Heights 2018 0 USER S MANUAL DAS-G01 The Power of Tomorrow Richmond Heights 2018 Page 1 USER'S MANUAL TABLE OF CONTENTS Page # 1.0 GENERAL INFORMATION...
More informationWavePRO Wireless Programmable T2500 Thermostat & R2500 Receiver OPERATING MANUAL. Model K
WavePRO Wireless Programmable T2500 Thermostat & R2500 Receiver OPERATING MANUAL Model K2500-001 1 THE PECO WAVEPRO WIRELESS SYSTEM Thank you for choosing the PECO WavePRO TM Wireless System (Model K2500-001).
More informationSemi flush-mounted room temperature controllers with LCD
s 3 077 RDD310 RDE410 Semi flush-mounted room temperature controllers with LCD For heating systems RDD310 RDE410 RDD310 and RDE410 features: Operating voltage AC 230 V 2-position control with On / Off
More informationMeasure & Control Temperature & CO2 levels with analog & digital I/O
MADE IN OZ HTC-DIGITAL-LCD PROGRAMMABLE TEMPERATURE CONTROLLER c/w YEARLY PROGRAMMABLE TIME SWITCH COMPATIBLE WITH A WIDE RANGE OF SENSORS ROOM O/A WALL DUCT PIPE Use Features Measure & Control Temperature
More informationDataNab it8: Intelligent Communicating Thermostat
DataNab it8: Intelligent Communicating Thermostat CONTENTS: - Title Page (This Page) Page 1 - Description Page 2 - Technical Specs Page 2 - Features Page 2 - Dimensions Page 2 - Installation Page 3 Page
More informationModel FP700 Owner s Instructions
The benefits of owning a Freedom Advantage Thermostat Large easy to read backlit display Selectable programming modes: 5-2, 5-1-1 or 7 day Manufactured by the makers of ACCUSTAT controls ServiceWatch for
More informationFree Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit
Document No. 155-324 Free Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit Description Features Application Product Number Room temperature controller for four-pipe fan coil units.
More informationField selectable application type and room module series, via dip-switches on controller
TUC03 Plus Configurable Terminal Unit Controller Product bulletin The TUC03 Plus configurable Terminal Unit Controller is specifically designed to provide an improved BACnet integration. It allows the
More informationUnderfloor Controllers
Price Underfloor Controllers work with the entire line of Price Diffusers and Terminal Units. The whole system can be easily integrated with plug-and-play connections and BACnet communication. With a full
More informationRoom Temperature Controller
3 023 Room Temperature Controller for four-pipe fan coil units RCC30 Outputs for on / off valve actuators Outputs for three-speed fan Control depending on room or return air temperature Operating modes:
More informationSE7600E Series Application Guide
SE7600E Series Application Guide Schneider Electric SE7600E Series RTU Controller with IAQ Control Application Guide CONTENTS Solution Overview 2 Product Overview 3 Features & Benefits 3 System Overview
More informationVariable Flow Rate Control Unit
VAV Produktdata TEKNISK DOKUMENTATION VENTILATION BG BURCHARTH A/S Variable Flow Rate Control Unit Model BVAV-R: VAV unit that has circular section. BVAV-RS: VAV terminal unit. BVAV-Q: VAV unit that has
More informationColour Touch Panel 3.5
Guangzhou Video-star Electronics Industrial Co., Ltd K-BUS R Colour Touch Panel 3.5 User manual-ver. 1.2 CHTF-35/01.1 CHTF-35/01.2.21 CHTF-35/01.2.22 CHTF-35/01.2.24 KNX/EIB Intelligent Installation Systems
More informationINDOOR UNIT CONTROLLER (IUC) Operation Manual
INDOOR UNIT CONTROLLER (IUC) Operation Manual Date: 9 June 2015 Issue: 4 Note: Information in this document applies to IUC controllers programmed with software version 1.5. Page 1 of 11 Contents 1. Introduction...
More informationRoom controller LS 990 / LS plus Stainless Steel / Aluminium
Room controller LS 990 / LS plus Stainless Steel / Aluminium 1 RCDES 2021 RCDES 2022 RCDES 2023 RCDES 2024 RCDES 2044 2 Ref.-No. KNX room controller display ETS-product family: Heating, ventilation, A/C
More information7-day room temperature controller
s 2 205 7-day room temperature controller Heating or cooling applications REV24.. Use Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display
More informationWall mounted units. Please read carefully and thoroughly this manual before operating this unit and save it in a safe place for future reference.
OWNERS' MANUAL REMOTE CONTROLLER Wall mounted units Please read carefully and thoroughly this manual before operating this unit and save it in a safe place for future reference. Warning. Be sure there
More informationOperation 6035 ENGLISH PROG MENU
Operation 6035 PROG MENU ENGLISH Operation 6035 Program button Time of day Day Time Slot Current Room Temperature Target Temperature Menu button PROG MENU FAN AUTO ON COOL OFF HEAT Fan Switch Touch Screen
More informationHTW-IZ12-24V-0-10V Touch Screen Thermostat Manual
HTW-IZ12-24V-0-10V Touch Screen Thermostat Manual Technical Data Power Supply AC24V Installation Surface-mounting Fan Power Supply 24V/ 110V/ 240V 50/60Hz Sensor NTC Valve output 0-10V Accuracy ±0.5 C
More informationRCF-230CAD. Communicating room controller for fan-coil applications with two analogue V DC outputs
revision 01 2015 RCF-230CAD Communicating room controller for fan-coil applications with two analogue 0...10 V DC outputs RCF-230CAD intended to control heating and/or cooling in 2- or 4-pipe installations.
More informationML Multi Stage Thermostat Installation & User Guide
ML Thermostat PR0122-STA PR0123-STA ML Multi Stage Thermostat Installation & User Guide For Products: - PR0710, PR0711, PR0720, PR0721 Resource Data Management Ltd 80 Johnstone Avenue, Hillington Industrial
More information24-hour room temperature controller
s 2 201 24-hour room temperature controller Heating applications REV13.. Use Mains-independent, battery-operated room temperature controller featuring user-friendly operation, easy-to-read display and
More informationI2:34 MODEL TSTATBBP2W01 PROGRAMMABLE DIGITAL THERMOSTAT. Heat only, or Cool only. Meets California Title 24 Residential USERS INFORMATION MANUAL
USERS INFORMATION MANUAL Heating & Cooling Systems MODEL TSTATBBP2W01 PROGRAMMABLE DIGITAL THERMOSTAT NOTE TO INSTALLER: This manual must be left with the equipment user. I2:34 72 72 Heat only, or Cool
More informationInnovations for utilities and their customers. Smartgrid Solutions
Innovations for utilities and their customers. Smartgrid Solutions Innovations for utilities and their customers. Leviton s Smartgrid Solutions function as a complete network. Leviton offers a full suite
More informationIn the following learning unit, you will simulate parameterising the heating function in the ETS.
Introduction Introduction: Heating control plays an important role in building technology. The most energy is consumed in heating buildings. With intelligent control, the effort is reduced while the level
More informationADVANCED REMOTE CONTROL
ADVANCED REMOTE CONTROL (SUITS IP28) INSTALLATION & OPERATING INSTRUCTIONS 918-962 12/07/10 The Advanced Remote Control is tested safe when installed in accordance with this installation manual. It is
More informationOP10. Pre-programmed, configurable controller for simple applications
revision 10 2013 OP10 Pre-programmed, configurable controller for simple applications The Optigo OP10 range of controllers can be set to handle everything from temperature or humidity control to control
More informationTstat8. Bacnet Thermostat
Tstat8 Bacnet Thermostat This full-featured thermostat is designed for cooling and heating systems in residential and commercial buildings. The thermostat can be configured for use with air handlers, fan
More informationMX1 Reversible AC Motor Controller. Supplementary Wiring Examples
MX1 Reversible AC Motor Controller Supplementary Wiring Examples DANGER Electrocution Hazard! Ensure all power is disconnected before servicing or wiring. Install all electrical equipment and wiring in
More informationQAX50.1 QAX50.5 QAX51.1 QAX51.5. Flexible room unit. Desigo RXC
1 648 Desigo RXC Flexible room unit for integrated operation of HVAC, lighting and blinds in individual rooms; with LONMARK -compatible bus communication QAX50.1 QAX50.5 QAX51.1 QAX51.5 Room temperature
More informationSetpoint Limits. Setpoint Limits products.koer.com Page 1 of 7
2017 products.koer.com Page 1 of 7 INTRODUCTION Learn how to change between which user can change the desired Setpoint 2017 products.koer.com Page 2 of 7 Step 1 Enter Advanded Menu ONLY AUTHORIZED MAINTENANCE
More informationMicroprocessor based Temperature / CO2 Controller c/w 365 Day Time Switch & Modbus Communication.
HTC-DIGITAL-LCD Microprocessor based Temperature / CO2 Controller c/w 365 Day Time Switch & Modbus Communication. Features Use Australian Made and designed LCD 2 X 16 Character Backlit Display Five Programmable
More informationThe Bard BrightStat Room Controllers
The Bard BrightStat Room Controllers Introduction Smart energy management has never been easier than with the BrightStat Room Controllers for Bard Air Conditioning and Heat Pump applications. Designed
More informationOperating Instructions. Radio timer thermostat display. Table of contents
Operating Instructions Table of contents 1. On these instructions... 2 2. How the radio timer thermostat display functions... 2 3. Normal view in the display... 3 3.1. Basic operation of the radio timer
More informationRoom unit with PPS2 interface
s 1 640 1640P01 Desigo RX Room unit with PPS2 interface For use with: QAX34.3 Equipment from the RXC, RXB, RXL and RXA (PPS2) ranges Desigo PX automation stations 1) Devices with a PPS2 interface Measurement
More informationWebselect VAV Selection/Pricing Quick Start User Guide for Manufacturer Rep Users
Webselect VAV Selection/Pricing Quick Start User Guide for Manufacturer Rep Users To Select, Price, Quote, Generate submittals and order VAV products, following the following process: Table of Contents
More informationPush-buttons 18. Light scenes push-buttons 21. Push-buttons with thermostat 22. Labelling ields 24
A wide array of alternative materials and colours have been added to the convenient variety of KNX functionality of the. Frameless KNX push-button with full-material rockers (glass, stainless steel and
More informationFeatures and Benefits of XeteX Controls. Other Unit Control Functions. Energy Recovery Functions
Controls Guide for XeteX Units Beyond meeting the typical specification and performance requirements, controlling the equipment is usually the most important success factor for HVAC projects. XeteX provides
More informationProduct and Application Description
Technical Product - Information Product and Application Description The room temperature controller UP 237K and UP 252K are available in the following colors, matching the design of the wall switch design
More informationNetworkable VAV Controller Specification and Installation Instructions. Controller Model EVCB14NIT4X (4 TRIACS / independent / external motor)
Controller Model EVCB14NIT4X (4 TRIACS / independent / external motor) For use with external floating or modulating actuators TRL Series Thermostat TRL24 (Thermostat 2x4) TRLH24 (Thermostat 2x4 with Humidity)
More informationFCU-4 FAN COIL CONTROLLER
FCU-4 FAN COIL CONTROLLER BACnet Enabled Description The FCU-4 is designed to provide complete control of fan coil units. The FCU-4 incorporates all the inputs and outputs to ensure that this advanced
More informationRoom Temperature Controllers
3 021 Room Temperature Controllers for two-pipe fan coil units RCC10 Output for on / off valve actuator Outputs for three-speed fan Control depending on the room or return air temperature (RCC10) Automatic
More informationSEZ7656R1045B / SEZ7656H1045B
SEZ7656R1045B / SEZ7656H1045B Installation Guide f BACnet MS-TP RTU / HP Room Controllers F Commercial Zoning Systems CONTENTS Installation 2 Location 2 Installation 2 BACnet System Overview 3 Terminal,
More informationSEZ7656E1045B. Installation Guide for BACnet MS/TP RTU Terminal with IAQ Control CONTENTS
SEZ7656E1045B Installation Guide f BACnet MS/TP RTU Terminal with IAQ Control CONTENTS Installation 2 Location 2 Installation 2 BACnet System Overview 3 Terminal, Identification and Function 4 Wiring 4
More informationCONTROLLER INSTALLATION OPERATION & QUICK START
CONTROLLER INSTALLATION OPERATION & QUICK START Controller: 8403-066 ECU Series Controller Manual: 2100-559 Supersedes: NEW File: Tab 19 Date: 05-02-11 Page 1 of 6 TABLE OF CONTENTS Installation Note...
More informationAppendix JA5 - Technical Specifications For Occupant Controlled Smart Thermostats
2016 Joint Appendices Appendix JA5-1 Joint Appendix JA5 Statewide Utility Team s Proposed Revisions to JA5 Last update October 17, 2015 All revisions are marked in red text. Additions to the existing code
More informationT7350 Keypad Configuration
Setup Using Keypad T7350 Keypad Configuration QUICK GUIDE NOTE: Refer to Fig. 1 and Table 2 for keypad description and details. A combination of key presses are required to use the Installer Setup feature:
More informationType Differential pressure transducer
Homepage > Products > Control systems > Control system EASYLAB - LABCONTROL > Sensor systems > Type Differenzdrucktransmitter Type Differential pressure transducer FOR THE DIFFERENTIAL PRESSURE RECORDING
More informationRickard MLM PC Software User Manual
Rickard MLM PC Software User Manual User Manual and Instructions Introduction Rickard MLM PC based software is provided to enable viewing and easy manipulation of a network of Rickard VAV diffusers with
More information3000 CONTROLLER TRAINING MANUAL. April 26, 2012 Software Version
3000 CONTROLLER TRAINING MANUAL April 26, 2012 Software Version 1.59.03 Contents 3000 CONTROLLER USER GUIDE Quick Reference: Using the 3000... 3 Menu Summary Tree... 6 Main Menu: Programming your Fryer...
More informationMICRO GROW GREENHOUSE SYSTEMS, INC
MICRO GROW GREENHOUSE SYSTEMS, INC 4065 ZEVO DR., UNIT B-, TEMECULA, CA 9590 PHONE (95) 96-3340 FAX (95) 96-3350 www.microgrow.com Revision., -09-0 Growstat Control Series INSTALLATION PROCEDURES SERIES
More informationCommunicative controller for VAV systems
FCR015 Communicative controller for VAV systems Summary FCR015 is a communicative controller for heating and cooling panels and a VAV (variable air volume) damper. It measures temperature and CO 2 concentration
More informationTemperature control unit
Temperature control unit 5739 18/19 Installation manual Part. U3582A - 12/08-01 PC Contents 1 - Introduction 5 1.1 - Warnings and tips 5 1.2 - Contents of package 5 2 - Description of the Control unit
More informationAndover ContinuumTM Infinet II
Andover ContinuumTM Infinet II i2920 System Controllers The Andover Continuum Infinet II i2920 System Controller is designed to meet the needs of your most demanding control and monitoring applications
More information