JPTLIIPA VoIP INTERFACE FOR JP SYSTEM INSTALLATION MANUAL

Size: px

Start display at page:

Download "JPTLIIPA VoIP INTERFACE FOR JP SYSTEM INSTALLATION MANUAL"

Anthony Little
6 years ago
Views:

1 JPTLIIPA VoIP INTERFACE FOR JP SYSTEM INSTALLATION MANUAL AIPHONE V1.1

2 Prohibited Do not dismantle unit Keep unit away from water General precautions WARNING Negligence could result in death or serious injury. 1. Do not dismantle or alter the unit. Fire or electric shock could result. 2. Do not connect any non-specified power source to the +, - terminals. Also, do not install two power supplies in parallel to a single input. Fire or damage to the unit could result. 3. Keep the unit away from water or any other liquid. Fire or electric shock could result. 4. Do not put any metal or flammable material into the unit through the openings. Fire, electric shock, or unit trouble could result. 5. Do not connect any terminal on the unit to an AC power line. Fire or electric shock could result. 6. Do not use power supply with a voltage other than specified. Fire or electric shock could result. 7. Keep AC cord from being marred or crushed. If the AC cord is damaged, fi re or electric shock could result. 8. Do not plug or unplug unit with wet hands. Electric shock could result. 9. Insert AC plug completely and securely into AC outlet. Otherwise, fi re or electric shock could result. 10. Periodically check for and remove dust on the power plug. If dust is left, it could cause the power plug to heat up, resulting in fire. 11. Do not put any metal or flammable material into the unit through the openings. Fire, electric shock, or unit trouble could result. CAUTION Negligence could result in injury or damage to property. 1. Do not install or make any wire terminations while power supply is plugged in. It can cause electrical shock or damage to the unit. 2. When mounting the unit on a wall, install the unit in a convenient location, but not where it could be jarred or bumped. Injury could result. 3. Before turning on power, make sure wires are not crossed or shorted. Fire or electric shock could result. 4. Do not install the unit in locations subject to frequent vibration or impact. It may fall or tip over, resulting in damage to the unit or personal injury 5. For power supply, use Aiphone power supply model specified for use with system. If non-specified product is used, fi re or malfunction could result. 6. Do not apply high pressure on the screen. If fractured, injury could result. 7. If LCD is punctured, do not touch the liquid crystal inside. Inflammation could result. If contact should occur, flush or rinse area with water thoroughly and consult your doctor. 8. Do not put anything on the unit or cover the unit with cloth, etc. Fire or unit trouble could result. 9. Do not install the unit in any of the following locations. Fire, electric shock, or unit trouble could result. * Places under direct sunlight or near heating equipment that varies in temperature. * Places subject to dust, oil, chemicals, hydrogen sulphide (hot spring). * Places subject to moisture and humidity extremes, such as bathrooms, cellars, greenhouses, etc. * Places where the temperature is quite low, such as inside a refrigerated area or in front of an air conditioner. * Places subject to steam or smoke (near heating or cooking surfaces). * Where noise generating devices such as dimmer switches or inverter electrical appliances are close by. 10. Be sure to perform a call test or check the volume with the handset on the hook. If you operate the hook switch with the handset on your ear, a sudden call etc. may arrive causing damage to your ear. 11. The unit must be installed and wired by a qualified technician. GENERAL PRECAUTIONS 1. Keep the unit more than 1 m (3.3') away from radio or TV sets. 2. Keep the intercom wires more than 30cm (12'') away from AC V wiring. AC induced noise and/or unit malfunction could result. 3. Comply with all third party manufacturing specifications that will be used with this system (sensors, door releases, etc.). 4. If it is used close to a cellular phone, the unit may malfunction. 5. The unit can be damaged if dropped. Handle with care. 6. The unit will not work during power failure. 7. In areas where broadcasting station antennas are close by, the intercom system may be affected by radio frequency interference. 8. All the units, except for door stations, are designed for indoor use only. Do not use at outdoor locations. 9. This product, providing door release, should not be used as a crime prevention device. 10. Please note the LCD panel, though manufactured with very high precision techniques, inevitably will have a very small portion of its image elements always lit or not lit at all. This is not considered a unit malfunction. 11. Environmental sound around the unit may hinder smooth communication, but this is not a malfunction. 12. The unit has audio monitoring function between residential stations. When using this function for baby monitoring, never install the unit within reach of children to prevent strangulation with coil cord or wires. NOTICES We will under no conditions be liable for damage occurring due to the inability to communicate due to malfunctions, problems, or operational errors in this product. We will under no conditions be liable for any damages or loses resulting from this product's contents or specifications. This manual was created by Aiphone Co., Ltd., all rights reserved. Copying, in part or in whole, this manual without prior permission from Aiphone Co., Ltd. is strictly forbidden. Please note that images and illustrations depicted in this manual may differ from the actual ones. Please note that this manual may be revised or changed without prior notice. Please note that product specifications may be changed for the sake of improvement without prior notice. This system is not intended for life support or crime prevention. It is a supplementary means of conveying information. Aiphone will under no conditions be liable for loss of life or property which occurs while the system is being operated. * In order to obtain the correct operation of the device, it is essential to have a data bandwidth greater than or equal to 500 kbps. AIPHONE V1.1

desktop or - wall mounted (use for example two screws type M3,5).

3 [1] [2] [3] [4] [5] Content : [1] Installation manual [2] User manual [3] JPTLIIPA [4] Power supply [5] Fast installation manual JPTLIIPA can be installed: - on desktop or - wall mounted (use for example two screws type M3,5). JPTLIIPA must be installed as far as possible from humidity or heating source. AIPHONE V1.2

State lighting ON : POWER ON OFF : POWER OFF State Lightning State JPTLIIPA Lit green fixed During initialization 1 blinking all the seconds Correct functioning 3 blinking all the seconds JPTLIIPA

4 State lighting ON : POWER ON OFF : POWER OFF State Lightning State JPTLIIPA Lit green fixed During initialization 1 blinking all the seconds Correct functioning 3 blinking all the seconds JPTLIIPA did not find an IP address (DHCP did not work). JPTLIIPA started with an address blinking all the seconds JPTLIIPA has no connection with server proxy 5 blinking all the seconds JPTLIIPA is not registered on server SIP AIPHONE V1.2

1 JPTLIIPA wiring JPTLIIPA JP4MED JP Door Station 1A1 1A2 A1 A2 M (IN) CAT5e M (OUT) 2A1 A1 To JP4HD M (OUT) 2A2 A2 See JPTLIIPA Install Manual Ethernet 100 Base TX LAN 3A1 3A2 JP Door Station 4A1

contact N 1 Power Supply 2V DC/0,5A(supplied) 230V AC + - PS2420DM + - Connections Panel function: - LAN: Ethernet port, - External Power supply 12VDC +/- 10% linear regulated: position + (12VDC), -

5 1 JPTLIIPA wiring JPTLIIPA JP4MED JP Door Station 1A1 1A2 A1 A2 M (IN) CAT5e M (OUT) 2A1 A1 To JP4HD M (OUT) 2A2 A2 See JPTLIIPA Install Manual Ethernet 100 Base TX LAN 3A1 3A2 JP Door Station 4A1 Alarm Input Optionnal Dry Contact 12VDC / 2A 24VDC / 1A NO: normaly open C: common NC: normaly closed S1E S1 NO C NC NO C NC NO C NC REL 1 REL2 REL 3 4A2 L1 L1 L2 L2 Output Dry contact N 2 Output Dry contact N 1 Power Supply 2V DC/0,5A(supplied) 230V AC + - PS2420DM + - Connections Panel function: - LAN: Ethernet port, - External Power supply 12VDC +/- 10% linear regulated: position + (12VDC), - (0V). (Consumption: 380mA in work, installed not far from 3 meters from JPTLIIPA). - Connection with bus on RJ45: - M(IN): cable from M(OUT) of JP4MED, - M(OUT) : cable to a possible sub-master station JP4HD. - Relay on JPTLIIPA on plug REL1, REL2 & REL3: - normally open (NO) on NO, - common on C, - normally closed (NC) on NC. Relay Contact Ratings: 2 Amp/12VDC - 1Amp/24VDC. Maximum tension: 24VDC. - Alarm function. - plug contact on S1 & S1E. AIPHONE V1.2

1- Behind Box or modem router (livebox, freebox, ) Connect JPTLIIPA directly on box or modem

6 Connecting JPTLIIPA system It can have several type of installation of JPTLIIPA. 2 Physical connection 2.1- Behind Box or modem router (livebox, freebox, ) Connect JPTLIIPA directly on box or modem router with Ethernet straight cable (not supplied). If no port Ethernet is available on your equipment, you will have to add a Switch 10/100Mbits/s (multiport Ethernet). AIPHONE V1.2

2.2- Modem without router function: Add an Ethernet router 10/100 Mbits/s with several Ethernet port to your installation. 2.

7 2.2- Modem without router function: Add an Ethernet router 10/100 Mbits/s with several Ethernet port to your installation Modem only USB: Ask to your ISP the replacement by an Ethernet modem. 2.4 Fast activation of JPTLIIPA: After check connections, put your installation and JPTLIIPA ON. JPTLIIPA connects via a server. When JPTLIIPA is registered on the server, the state led will blink green/orange. Activate your Smartphone application. When your Smartphone will be registered on the server, you can use your system. 3 TCP/IP network setting: There are several possible solutions. By default, JPTLIIPA is delivered in DHCP mode. JPTLIIPA is delivered with dynamic IP (DHCP): Go to 4 (connection via the proxy). If DHCP does not work, JPTLIIPA is automatically with a fixed IP address ( ). In this case, it is necessary to verify if JPTLIIPA is in the same sub-network as our PC: Make touch «windows» + R In the window which displays, enter «cmd» and «enter» Then «ipconfig» and «enter» Find line «Address IPv4», like x.y If x is not «0» : it is necessary to modify programming of network card : see Annexe A Launch your web browser (Internet Explorer, Firefox, ) In the address field of browser, enter the IP address of JPTLIIPA : Go to 4 (JPTLIIPA setting). AIPHONE V1.2

Double-click on «Local Area Connection» then «Properties» For Windows 8, make a right click on the icon Internet Access (Wi-Fi or Ethernet ) on

8 ANNEXE A Configuration and images below were realized under Windows XP, for the other versions of Windows the steps can be a little bit different. 1. Click on Start» Control Panel» Network Connections 2. Double-click on «Local Area Connection» then «Properties» For Windows 8, make a right click on the icon Internet Access (Wi-Fi or Ethernet ) on the toolbar then choose Network and Sharing Center. Click on Ethernet. In the box of properties of the connection to the LAN, choose the object «Internet Protocol Version 4 (TCP/IP)» and click on Properties. AIPHONE V1.2

Enter an IP address in the range of JPTLIIPA address by default: 192.168.0.

4 JPTLIIPA setting: Launch your web browser (Internet Explorer, Firefox, ) and in the address field of browser, enter http://jp.tliip.com.

9 Enter an IP address in the range of JPTLIIPA address by default: X (where X is a number between 1 and 254, here in our example 32) and use for the mask of sub-network. 4 JPTLIIPA setting: Launch your web browser (Internet Explorer, Firefox, ) and in the address field of browser, enter The PC is going to connect to the proxy, the following window displays: Enter the serial number of the device in User field and then click the To connect. Enter the password of JPTLIIPA, specified on the sheet of fast installation joined with JPTLIIPA. AIPHONE V1.2

10 The welcome screen of JPTLIIPA appears: The screen gives us information onto the state of the connections with the proxy and with the server Astérisk To modify the operating parameters of JPTLIIPA, click 'Parameters'. We obtain the following page AIPHONE V1.2

By using the choice static IP, it is afterward simpler to connect

11 4.1- Network TCP/IP setting In this menu we can choose to use the product in dynamic IP (active DHCP) or static IP. By using the choice static IP, it is afterward simpler to connect in local with the Internet browser (always the same IP address). AIPHONE V1.2

4.2-Programming of operating parameters This page allows the programming of parameters for relays and calls. When the user confirms the option ' End of comm.

after contact + 5sec ', the communication will end 5s after the of opening of door. 5 Smartphones settings: 1- Install the application AiphoneJP : a.

12 4.2-Programming of operating parameters This page allows the programming of parameters for relays and calls. When the user confirms the option ' End of comm. after contact ', the communication will be broken after the opening of door. If the option 'End of comm. after contact + 5sec ', the communication will end 5s after the of opening of door. 5 Smartphones settings: 1- Install the application AiphoneJP : a. With application «Barcode Scanner» (for example on the box and/or in the manual), the Smartphone goes directly on the corresponding store (Android or IOS). b. Without application, go to the store and search application «AiphoneJP» 2- Open the software AIPHONE V1.2

13 3- Welcome screen Click on Tools. 4- Automatic entry 5- Manual entry User name : fr140801_1 or fr140801_2 Password : specified on Fast installation manual Domain : sip.tliip.com And click on Apply AIPHONE V1.2

14 Operating temperature: 0 C - 40 C (32 F 104 F). Cleaning: use a soft duster with neutral detergent. Dimensions: 240 x 180 x 55 (h) mm. Weight: 0,180 kg Connections: Telephones: (1) Ethernet network (2) Bus JP (1) Smartphones Android or IPhone Power supply: 12V DC 0,5A Consumption: Standards: Exit Contact: Programming: Saving of parameters: Material: Stand-by 350mA, when relay is on 430mA. EN60950 EN55022 Edition 98 Classe B EN55024 Edition 98 Classe B 3 (N.O., N.F.) By Internet. No volatile memory ABS module AIPHONE V1.2

15 AIPHONE V1.2

16 Distributed by AIPHONE Printed in France AIPHONE V1.2

0311 A OI GTW-LC SERVICE MANUAL. GT System Lift control adaptor GTW-LC INSTALLATION & OPERATION MANUAL

0311 A OI GTW-LC SERVICE MANUAL. GT System Lift control adaptor GTW-LC INSTALLATION & OPERATION MANUAL 03 A OI GT System Lift control adaptor SERVICE MANUAL INSTALLATION & OPERATION MANUAL CONTENTS PRECAUTIONS General Prohibitions Prohibition to Dismantle the Unit Prohibition on Subjecting the Unit to Water