PD ProtEX-MAX TM Explosion-Proof Process Meter. IECEx MAX

Transcription

1 PD8-000 ProtEX-MAX Explosion-Proof Process Meter MAX IECEx process 0-0 ma, -0 ma, 0- V, - V, and ±0 V Inputs Input Power Options Include 8- VAC or - VDC Modern, Sleek and Practical Enclosure Display Mountable at 0, 90, 80, & 70 Degrees Explosion-Proof, IP8, NEMA X Enclosure SunBright Display Standard Dual-Scale for Level Applications Single Input Signal Input Conditioning for Flow & Round Horizontal Tanks -Point, Square Root, or Exponential Linearization Multi-Pump Alternation Control SafeTouch Through-Glass Button Programming Modbus RS-8 Serial Communications Flanges for Wall or Pipe Mounting Isolated ma Transmitter Power Supply Onboard USB and MeterView Pro Programming Software Precision Digital Corporation

2 PD8-000 ProtEX-MAX Through-Glass Button Programming Explosion-Proof Process Meter IECEx Sunlight Readable Display Mounting Flanges (Up to ½" Pipe) SafeTouch Enter or Alarm Acknowledge Button Locking Screw Large 0." Digits On Upper Display SafeTouch Menu Button Explosion-Proof Die-Cast Aluminum NEMA X Enclosure PV, Max (Peak), Min (Valley) Programmable Function Keys User Configurable Lower Display Alarm Status Indicators Two ¾" NPT Conduit Plugs SafeTouch Right Arrow SafeTouch Display or Up Arrow INTRODUCTION SafeTouch Button Programming Key Features Standard SunBright LED Display The ProtEX-MAX is equipped with four The ProtEX-MAX PD8-000 has been designed to offer the functions sensors that operate as through-glass buttons and features of the PROVU PD000 in a great looking fully FM, CSA, so that it can be programmed and operated ATEX, and IECEx approved explosion-proof product. The PD8 without removing the cover (and exposing the series is not just a /8 DIN meter mounted in an explosion-proof electronics) in a hazardous area. The SafeTouch housing; a special bezel and electronics were designed exclusively buttons are configured by default to duplicate for the ProtEX-MAX. The bezel and faceplate give the front panel a the function of the front panel mechanical very finished appearance and house the additional electronics for pushbuttons associated with the integrated meter. the PD8. The ProtEX-MAX s SunBright display features extraordinarily bright LEDs. They are perfect for indoor and outdoor applications where visibility may be impaired by smoke, fog, dust, or distance or even in direct sunlight. Precise, Accurate, and More Informative ProtEX-MAX s large 0." upper display provides a highly accurate and precise -digit view of the process measurement. Its -bit A/D is accurate to ±0.0% of calibrated span ± count. Flow in CFH Free USB Programming Software & Cable The ProtEX-MAX comes preloaded with free MeterView Pro programming software that connects and installs directly to your PC with a standard USB cable, also provided free with each instrument. This eliminates the need to insert CDs, install drivers, or download software from the internet. The software will allow you to configure, monitor, and datalog a ProtEX-MAX PD8-000 using your PC. Just simply connect the meter to your PC with the USB cable and within minutes you will be programming it. Gallons & Setpoint Free USB Cable Included Level in Feet for Easy Software Installation Pressure Indication Configurable The upper display can be programmed to indicate PV, maximum (peak), minimum (valley), alternating maximum/minimum, one of eight alarm set points, or Modbus input. The lower display can also be configured to display engineering units, set points, user defined legends, or simply turned off. PD8 Module

3 PD8-000 ProtEX-MAX Explosion-Proof Process Meter Dual-Scale Display Feature Easy to Program The ProtEX-MAX PD8-000 has a rather unique, and very flexible dual-scale capability; a second scaled display can represent the measured input in a different form (i.e. gallons & height). This is of particular value in level applications. Please see the examples shown below. Both displays are independently scaled and are based on the -0 ma input signal. Beyond level, this function has been used for pressure & force, current & power, feet & meters, GPM & CFM, and more. The user friendly dual-line display makes the ProtEX-MAX easy to set up & program. No jumpers to set for input selection. All setup & programming can be done using the SafeTouch buttons on the front of the meter face. Three levels of password protection help maintain the reliability of the programming. Input Setup Digital communications Gallons & Height Gallons & ma Display Setup Modbus RTU Serial Communications Gallons & Percent With the purchase of a serial communication adapter, ProtEX-MAX meters can communicate with any Modbus Master device using the ever-popular Modbus communications protocol that is included in every ProtEX-MAX. This greatly increases the flexibility of the meter. Modbus provides much more capability than read PV and write set points. Below are some examples of other things that can be done with ProtEX-MAX s Modbus communications. Gallons & Head PSI Advanced Linearization Capability The ProtEX-MAX includes a -point linearizer. In non-linear level applications (i.e. some pumping or lift stations), it can easily compensate for submerged equipment or plumbing that displace usable volume. A second independent 8-point linearizer is available for a second scaled display (PV) when Level function is enabled. Precision Digital s free MeterView Pro PC-based software greatly simplifies the construction of the linearization tables. The software can save this data to the meter and/or PC. Send a -character message to the lower display upon an event Convert a digital value to a -0 ma signal Remote user control (i.e. change set points, acknowledge alarms) Input a Modbus digital PV (in place of analog input) Remote override of any, or all, relays and analog outputs On-Board Digital Input The PD8-000 includes a digital input as standard. This digital input can operate with the tare, reset tare, or interlock relays feature, force relays on from a signal from a PLC or relay on other equipment, and much more. This is ideal for installations where the meter is inaccessible behind a cover, or where an additional function key is needed for customized operation. P+ P- F COM V+ ma+ Rounding Modbus PV Input Remote Message ProtEX Videos Visit our archive at /videos to watch a video on the ProtEX-MAX Family of Explosion-Proof Meters. Here, you will also find other videos on the ProtEX Series including videos on loop powered process meters, feet and inches level meters, and flow rate/totalizers. Also, see the SafeTouch through-glass button programming in action. ACK The rounding feature is used to give the user a steadier display with fluctuating signals. It causes the display to round to the nearest value according to the rounding value selected (,,, 0, 0, 0, or 00). For example, with a rounding value of 0, and a input of, the display would indicate 0. Max/Min Display Max/Min (or Peak/Valley) is standard on the ProtEX-MAX PD Either display can be configured to show either maximum or minimum excursion since last reset. The displays can also be configured to toggle between Max and Min values. Both values can be simply reset from the front panel.

4 PD8-000 ProtEX-MAX Explosion-Proof Process Meter INTEGRATED DIGITAL I/o and serial MeterView Pro Software communications Configure, monitor, and datalog a ProtEX-MAX PD8-000 from a PC using MeterView Pro Software (available via USB or for download at ). See samples below of monitor and data logging, linearization utility, setup, and relays. Monitor & Datalog RS-8 Connectors Digital I/O Connectors Linearization Utility Digital I/O Connections Four digital inputs and four digital outputs come standard with the ProtEX-MAX. External digital inputs can function similarly to the front panel function keys or digital input F. They can be configured to trigger certain events (i.e. acknowledge/reset alarms, reset max and/or min values, disable/enable all output relays, and hold current relay states), or provide a direct menu access point. The inputs can be used to configure the meter remotely using panel mount push buttons on a control station, giving the user remote control of the four front panel push buttons. Digital outputs can be used to remotely monitor the ProtEX-MAX s alarm relay output states, or the states of a variety of actions and functions executed by the meter. Setup Note: The onboard digital inputs (-) are configured at the factory to function identically to the front panel pushbuttons (Menu, F, F, & F) in order to work with the SafeTouch buttons. Changing the programming of the digital inputs will affect the function of the SafeTouch buttons. Serial Communications Connections Relays ProtEX-MAX meters come with an RS-8 connection for serial communications with other digital devices. The industry standard Modbus RTU protocol is included with every meter.

5 PD8-000 ProtEX-MAX Explosion-Proof Process Meter OUTPUTS Relay Outputs The ProtEX-MAX has up to four A Form C relays (SPDT) with multiple power loss fail-safe options. Relays can be configured for proper protective action upon input loop break. Relay ON and OFF delay times are user adjustable. Up to four front panel indicators show alarm and/or relay state. All relays can be configured for 0-00% deadband. Relay Operation/Configuration There are powerful relay functions that can be configured in the ProtEX-MAX meter, including: Automatic reset only (non-latching) Automatic + manual reset at any time (non-latching) Latching (manual reset only) Latching with clear (manual reset only after alarm condition has cleared) Pump alternation control (automatic reset only) Sampling (activated for a user-specified time) User selectable fail-safe operation Relay action for loss (break) of -0 ma input signal Time delay (on and off), independent for each relay Manual control mode Interlock relay mode Analog Output The isolated analog retransmission signal can be configured to represent the process variable (PV), maximum (peak) value, minimum (valley) value, the value for any of the eight relay set points, or Modbus input. While the output is nominally -0 ma, the signal will accurately accommodate under- and over-ranges from to ma. Interlock Relay(s) This function allows a process to use one or more very low voltage input signals or simple switch contacts to control the state of one or more internal interlock relays. A violation (i.e. loss of input, open switch, or open circuit) forces one or more N/O interlock relay contacts to open. One input can be used in series with a number of interlock switches, or up to eight inputs can be required to force-on one (or more) internal interlock relays. Please see Safety Interlock on the ProVu Series whitepaper on our website for more information. +V I Interlock Contact (Digital Input) Signal input conditioning COM Control Relay LOAD Non-linear input signals (i.e. weirs & flumes, differential pressure, etc.) can be linearized with the ProtEX-MAX s simple to use built-in signal input conditioners, such as: square-root extractor, exponential linearizer, horizontal round tank linearizer, or the ProtEX-MAX s powerful general purpose -point linearizer. COM Interlock Relay NEUT VAC Manual Output Control Take control of any output with this feature. All relays can be forced ON or OFF, and the -0 ma output signal can be set to any value within its range. When the relays and -0 ma output are controlled manually, an LED labeled M is turned on and the associated Alarm LEDs (-8) flash every 0 seconds indicating that the meter is in manual control mode. Isolated Transmitter Power Supplies A powerful ma power supply is a standard feature on the ProtEX-MAX meter. It can be configured for, 0, or V (default) by means of a simple internal jumper (see manual). An additional power supply ( ma) is standard with the -0 ma output option. Sampling Function (PV Triggered Timed Relay) The sampling function allows the operator to set a set point for a sampling relay. When the PV reaches that set point, it will close that relay s contacts for a preset period of time (0. to seconds). An example of its use may be for beer/ale fermentation. When the batch reaches a certain ph, the relay contacts would close and by some means (light, horn, etc.) alert someone to take a sample, or provide the trigger to automatically take a sample of the batch. The utility of this function can, of course, be expanded beyond sampling and be used whenever a timed relay output closure is required when the PV reaches a certain set point. Weir Flow Calculated Using Exponential Signal Input Conditioner Round Horizontal Tank Signal Input Conditioner

6 PD8-000 ProtEX-MAX Explosion-Proof Process Meter Dimensions Multi-Pump Alternation Up to 8 pumps can be alternated/sequenced. Units: Inches (mm) Connections Form C (SPDT) relays Two isolated supplies available even on / VDC input power models Removable terminal blocks or relays + isolated -0 ma output option -0 ma Output Powered by ProtEX-MAX RELAY RELAY RELAY RELAY C C C - + MA OUT C I- I+ R V SIGNAL ProteX-MAX Explosion-Proof P+ P- F COM V+ ma+ 7 8 M-LINK All the proven features of the PROVU brought into your hazardous areas! Go to /pd8 + - ProtEX-MAX provides ma to power the transmitter PD8-000 ProtEX-MAX Explosion-Proof + - POWER M-LINK connection from Integrated electronics to ProtEX-MAX connector board. Universal 8- VAC or / VDC input power Voltage or current inputs No jumpers needed for V/mA input selection M-Link for adding expansion modules Digital input (F)

7 PD8-000 ProtEX-MAX Explosion-Proof Process Meter SPECIFICATIONS Except where noted all specifications apply to operation at + C. General Display: Upper display: 0.0" ( mm) high. Lower display: 0." ( mm) high. Both are digits ( to ), red LEDs. Display Intensity: Eight intensity levels Display Update Rate: /second (00 ms) Overrange: Display flashes Underrange: Display flashes Display Assignment: The upper and lower displays may be assigned to PV, PV, PCT (percent), max/min, alternate max & min, set points, units (lower display only), or Modbus input. Programming Methods: Four SafeTouch through-glass buttons when cover is installed. Four internal pushbuttons when cover is removed. F Digital Input Contacts:. VDC on contact. Connect normally open contacts across F to COM. F Digital Input Logic Levels: Logic High: to VDC; Logic Low: 0 to. VDC Noise Filter: Programmable from to 99 (0 will disable filter) Filter Bypass: Programmable from 0. to 99.9% of calibrated span Recalibration: Calibrated at the factory. Recalibration is recommended at least every months. Max/Min Display: Max / min readings reached by the process are stored until reset by the user or until power to the meter is turned off. Password: Three programmable passwords restrict modification of programmed settings. Non-Volatile Memory: All programmed settings are stored in nonvolatile memory for a minimum of ten years if power is lost. Input Power Options: 8- VAC 0/0 Hz, 90- VDC, 0 W max, or optional model with - VDC ±0%, W max. Fuse: Required external fuse: UL Recognized, A max, slow blow; up to meters may share one A fuse. Isolated Transmitter Power Supply: Terminals P+ & P-: VDC ± 0%. Isolated from the input at >00 V. Jumper selectable for, 0, or VDC supply (internal jumper J). All models transmitter supply ma max. Normal Mode Rejection: Greater than 0 db at 0/0 Hz Isolation: kv input/output-to-power line. 00 V input-to-output or output-to-p+ supply. Overvoltage Category: Installation Overvoltage Category II: Local level with smaller transient overvoltages than Installation Overvoltage Category III. Environmental: T Class operating temperature range Ta = -0 to 0 C T Class operating temperature range Ta = -0 to C Max Power Dissipation: Maximum power dissipation limited to. W. Connections: Removable screw terminal blocks accept to AWG wire, RJ for external relays, digital I/O, and serial communication adapters. Enclosure: Explosion-proof die cast aluminum with glass window, corrosion resistant epoxy coating, color: blue. NEMA X, 7, & 9, IP8. Default conduit connections: Four ¾" NPT threaded conduit openings and two ¾" NPT metal conduit plugs with mm hex key fitting installed. Additional conduit opening configurations may be available; verify quantity and sizes on specific device labeling during installation. Mounting: Four slotted flanges for wall mounting or NPS ½" to ½" or DN 0 to mm pipe mounting. Dimensions:." x 7.97" x 8.7" (W x H x D) ( mm x 0 mm x mm) Weight:.0 lbs (7. kg) Warranty: years parts & labor USB Connection: Compatibility: USB.0 Standard, Compliant Connector Type: Micro-B receptacle Cable: USB A Male to Micro-B Cable Driver: Windows 98/SE, ME, 000, Server 00/008, XP /-Bit, Vista /-Bit, Windows 7 /-Bit, Windows 0 /-Bit Power: USB Port Process Input Inputs: Field selectable: 0-0, -0 ma, ±0 VDC (0-, -, 0-0 V), Modbus PV (Slave) Accuracy: ±0.0% of calibrated span ± count, square root & programmable exponent accuracy range: 0-00% of calibrated span Temperature Drift: 0.00% of calibrated span/ C max from 0 to C ambient, 0.0% of calibrated span/ C max from -0 to 0 C ambient Signal Input Conditioning: Linear, square root, programmable exponent, or round horizontal tank volume calculation. Multi-Point Linearization: to points for PV or PV. to 8 points for PV (Dual-Scale Level feature) Programmable Exponent:.000 to.9999 Low-Flow Cutoff: (0 disables cutoff function) Decimal Point: Up to five decimal places or none: d.ddddd, dd.dddd, ddd.ddd, dddd.dd, ddddd.d, or dddddd. Calibration Range: -0 ma: minimum span input & input : 0. ma. ±0 V: minimum span input & : 0.0 V. An Error message will appear if input and input signals are too close together. Input Impedance: Voltage ranges: greater than MΩ. Current ranges: 0-00 Ω (depending on resettable fuse impedance). Input Overload: Current input protected by resettable fuse, 0 VDC max. Fuse resets automatically after fault is removed. Relays Rating: or SPDT (Form C) internal and/or SPST (Form A) external; rated 0 VDC and /0 VAC resistive load; / HP ( 0 /0 VAC for inductive loads such as contactors, solenoids, etc. Noise Suppression: Noise suppression is recommended for each relay contact switching inductive loads. Deadband: 0-00% of span, user programmable High or Low Alarm: User may program any alarm for high or low trip point. Unused alarm LEDs and relays may be disabled (turned off). Relay Operation: automatic (non-latching), latching (requires manual acknowledge), sampling (based on time), pump alternation control ( to 8 relays), Off (disable unused relays and enable interlock feature, manual on/off control mode). Relay Reset: User selectable via front panel buttons or digital inputs.. Automatic reset only (non-latching), when input passes the reset point.. Automatic + manual reset at any time (non-latching).. Manual reset only, at any time (latching).. Manual reset only after alarm condition has cleared (latching). Note: Front panel button or digital input may be assigned to acknowledge relays programmed for manual reset. Time Delay: 0 to seconds, on & off relay time delays. Programmable and independent for each relay. Fail-Safe Operation: Programmable and independent for each relay. Note: Relay coil is energized in non-alarm condition. In case of power failure, relay will go to alarm state. Auto Initialization: When power is applied to the meter, relays will reflect the state of the input to the meter. Serial Communications Protocol: Modbus RTU Meter Address/Slave ID: - 7 Baud Rate: 00-9,00 bps Transmit Time Delay: Programmable between 0 and 99 ms or transmitter always on for RS- communication Data: 8 bit ( start bit, or stop bits) Parity: Even, odd, or none with or stop bits Byte-to-Byte Timeout: seconds Turn Around Delay: Less than ms (fixed) Note: Refer to the PROVU Register Tables located at for details. 7

8 PD8-000 ProtEX-MAX Explosion-Proof Process Meter Isolated -0 ma Transmitter Output Output Source: Process variable (PV), max, min, set points -8, manual control setting, or Modbus input Scaling Range:.000 to.000 ma for any display range Calibration: Factory calibrated:.000 to = -0 ma output Analog Output Programming:.000 ma maximum for all parameters: Overrange, underrange, max, min, and break Accuracy: ± 0.% of span ± 0.00 ma Temperature Drift: 0. μa/ C max from 0 to C ambient, 0.8 μa/ C max from -0 to 0 C ambient Note: Analog output drift is separate from input drift. Isolated Transmitter Power Supply: Terminals I+ & R: VDC ± 0%. Isolated from the input at >00 V. May be used to power the -0 ma output or other devices. All ma max. External Loop Power Supply: VDC maximum Output Loop Resistance: Power supply Minimum Maximum VDC 0 Ω 700 Ω VDC (external) 00 Ω 00 Ω Product Ratings and Approvals FM: Type X; IP Class I, Division, Groups B, C, D Class II, Division, Groups E, F, G Class III, Division, T/T Class I, Zone, AEx d, IIC Gb T/T Zone, AEx tb IIIC T90 C; Ta -0 C to + C T Ta = -0 C to +0 C; T Ta = -0 C to + C Certificate Number: 078 CSA: Class I, Division, Groups B, C, D Class II, Division, Groups E, F, G Class III, Division Class I Zone Ex d IIC Zone Ex tb IIIC T90 C -0 C < Tamb. < +0 C; Temperature Code T -0 C < Tamb. < + C; Temperature Code T Enclosure Type X & IP Certificate Number: 7 ATEX: II G D Ex d IIC T* Gb Ex tb IIIC T90 C Db IP8 Ta = -0 C to +* C *T = -0 C to +0 C *T = -0 C to + C Certificate number: Sira ATEX8 IECEx: Ex d IIC T* Gb Ex tb IIIC T90 C Db IP8 Ta = -0 C to +* C *T = -0 C to +0 C *T = -0 C to + C Certificate Number: IECEx SIR.007 ordering information 8- VAC Model ProtEX-MAX PD8-000 Models - VDC Options Installed Model PD8-000-H0 PD H0 None PD8-000-H PD H Relays PD8-000-H PD H -0 ma Output PD8-000-H PD H Relays PD8-000-H PD H Relays & -0 ma Output PD8-000-H7 PD H7 Relays & -0 ma Output Note: V Transmitter power supply standard on all models. Model PDAPLUG7 PDA78-I PDA78-N PDA88-I PDA88-N Accessories Description /" NPT Stainless Steel Stopping Plug with Approvals RS- to RS-/8 Isolated Converter RS- to RS-/8 Non-Isolated Converter USB to RS-/8 Isolated Converter USB to RS-/8 Non-Isolated Converter PDA8 Pipe Mounting Kit Zinc Plated (Requires ) PDA8-SS Pipe Mounting Kit Stainless Steel (Requires ) Disclaimer Your Local Distributor is: The information contained in this document is subject to change without notice. Precision Digital Corporation makes no representations or warranties with respect to the contents hereof, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. 0 Precision Digital Corporation. All rights reserved. LDS8-000_A 0/ Precision Digital Corporation South Street Hopkinton MA 078 USA Tel (800) -00 Fax (08) -8990