DX200 OPTIONS MECHATROLINK-II COMMUNICATION FUNCTION INSTRUCTIONS

Transcription

1 DX200 OPTIONS MECHATROLINK-II COMMUNICATION FUNCTION INSTRUCTIONS (FOR MP2110-ET3 MADE BY YASKAWA ELECTRIC CORPORATION ) Upon receipt of the product and prior to initial operation, read these instructions thoroughly, and retain for future reference. MOTOMAN INSTRUCTIONS MOTOMAN- INSTRUCTIONS DX200 INSTRUCTIONS DX200 OPERATOR S MANUAL DX200 MAINTENANCE MANUAL The DX200 operator s manuals above correspond to specific usage. Be sure to use the appropriate manual. Part Number: CD Revision: 0 MANUAL NO. 0 1/38

2 MECHATROLINK-II CD MANDATORY This manual explains the MP2110-ET3 board of the DX200 system and general operations. Read this manual carefully and be sure to understand its contents before handling the DX200. General items related to safety are listed in Chapter 1: Safety of the DX200 Instructions. To ensure correct and safe operation, carefully read the DX200 Instruction before reading this manual. CAUTION Some drawings in this manual are shown with the protective covers or shields removed for clarity. Be sure all covers and shields are replaced before operating this product. The drawings and photos in this manual are representative examples and differences may exist between them and the delivered product. YASKAWA may modify this model without notice when necessary due to product improvements, modifications, or changes in specifications. If such modification is made, the manual number will also be revised. If your copy of the manual is damaged or lost, contact a YASKAWA representative to order a new copy. The representatives are listed on the back cover. Be sure to tell the representative the manual number listed on the front cover. YASKAWA is not responsible for incidents arising from unauthorized modification of its products. Unauthorized modification voids your product s warranty. ii 2/38

3 CD MECHATROLINK-II Notes for Safe Operation Read this manual carefully before installation, operation, maintenance, or inspection of the DX200. In this manual, the Notes for Safe Operation are classified as WARNING, CAUTION, MANDATORY, or PROHIBITED. WARNING CAUTION Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury to personnel. Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury to personnel and damage to equipment. It may also be used to alert against unsafe practices. MANDATORY Always be sure to follow explicitly the items listed under this heading. PROHIBITED Must never be performed. Even items described as CAUTION may result in a serious accident in some situations. At any rate, be sure to follow these important items. NOTE To ensure safe and efficient operation at all times, be sure to follow all instructions, even if not designated as CAUTION and WARNING. PROHIBITED Do not use or keep the board in the following environmental conditions. Improper usage of the board may damage the board. Where exposed to direct sunshine Where vibration or impact occurs Where high humidity exists Where a strong magnetic field exists Where much dust exists Where a sudden change in the temperature occurs Where corrosive gases occur Where condensation occurs iii 3/38

4 MECHATROLINK-II CD WARNING Before operating the manipulator, check that servo power is turned OFF when the emergency stop buttons on the front door of the DX200 and programming pendant are pressed. When the servo power is turned OFF, the SERVO ON LED on the programming pendant is turned OFF. Injury or damage to machinery may result if the emergency stop circuit cannot stop the manipulator during an emergency. The manipulator should not be used if the emergency stop buttons do not function. Figure 1: Emergency Stop Button Once the emergency stop button is released, clear the cell of all items which could interfere with the operation of the manipulator. Then turn the servo power ON. Injury may result from unintentional or unexpected manipulator motion. Figure 2: Release of Emergency Stop TURN Observe the following precautions when performing teaching operations within the P-point maximum envelope of the manipulator View the manipulator from the front whenever possible. Always follow the predetermined operating procedure. Keep in mind the emergency response measures against the manipulator s unexpected motion toward you. Ensure that you have a safe place to retreat in case of emergency. Improper or unintended manipulator operation may result in injury. Confirm that no persons are present in the P-point maximum envelope of the manipulator and that you are in a safe location before: Turning ON the DX200 power Moving the manipulator with the programming pendant Running the system in the check mode Performing automatic operations Injury may result if anyone enters the P-point maximum envelope of the manipulator during operation. Always press an emergency stop button immediately if there are problems.the emergency stop buttons are located on the right of the front door of the DX200 and the programming pendant. Before wiring, be sure to turn OFF the power supply and put up a warning sign, such as DO NOT TURN ON THE POWER. Failure to observe this warning may result in an electric shock or an injury. iv 4/38

5 CD MECHATROLINK-II WARNING Do not touch the inside of the panel for 5 minutes after the power is turned OFF. The remaining charged voltage in the capacitor may cause an electric shock or an injury. Be sure to close the door and install the protection cover while the power is turned ON. Failure to observe this warning may result in a fire or an electric shock. v 5/38

6 MECHATROLINK-II CD CAUTION Perform the following inspection procedures prior to conducting manipulator teaching. If problems are found, repair them immediately, and be sure that all other necessary processing has been performed. Check for problems in manipulator movement. Check for damage to insulation and sheathing of external wires. Always return the programming pendant to the hook on the cabinet of the DX200 after use. The programming pendant can be damaged if it is left in the manipulator's work area, on the floor, or near fixtures. Read and understand the Explanation of Warning Labels in the DX200 Instructions before operating the manipulator: The wiring and mounting must be performed by authorized and qualified personnel. Failure to observe this caution may result in a fire or an electric shock. Make sure that there is no foreign matter such as metal chips on the board. In case of malfunction, etc. it may result in an injury or damage the board. Make sure that there is no damage or deflection of parts on the board. In case of malfunction, etc. it may result in an injury or damage the board. Correctly connect each cable and connector. Failure to observe this caution may result in a fire or damage the board. Set the switches, etc. correctly. Malfunction, caused by an incorrect setting, may result in an injury or damage the board. Never touch the mounting surfaces of the board parts directly with fingers. The generated static electricity may damage the IC. Never touch the soldered surfaces of the board directly with fingers. Protrusions on the soldered surface may result in an injury. No shock to the board. The shock may damage the board. vi 6/38

7 CD MECHATROLINK-II Definition of Terms Used Often in This Manual The MOTOMAN is the YASKAWA industrial robot product. The MOTOMAN usually consists of the manipulator, the controller, the programming pendant, and supply cables. In this manual, the equipment is designated as follows: Equipment DX200 controller DX200 programming pendant Cable between the manipulator and the controller Manual Designation DX200 Programming pendant Manipulator cable Descriptions of the programming pendant, buttons, and displays are shown as follows: Equipment Programming Pendant Character Keys/ Symbol Keys Axis Keys/ Number Keys Keys pressed simultaneously Displays Manual Designation The keys which have characters printed on them are denoted with [ ]. ex. [ENTER] Axis Keys and Number Keys are generic names for the keys for axis operation and number input. When two keys are to be pressed simultaneously, the keys are shown with a + sign between them, ex. [SHIFT]+[COORD] The menu displayed in the programming pendant is denoted with { }. ex. {JOB} Description of the Operation Procedure In the explanation of the operation procedure, the expression "Select " means that the cursor is moved to the object item and the SELECT key is pressed, or that the item is directly selected by touching the screen. Registered Trademark In this manual, names of companies, corporations, or products are trademarks, registered trademarks, or brand names for each company or corporation. The indications of (R) and TM are omitted. vii 7/38

8 MECHATROLINK-II Table of Contents CD 1 Outline System Configuration Hardware Specifications MP2110-ET3 Specifications Specifications Supported Commands Setting and Mounting the MP2110 Board Mounting the MP2110 Board Mount the MP2110 Board Opening the Front Door of the DX Mounting the MP2110 Board on the DX Cable Connection Closing Front Door of the DX Setting of Optional Board and I/O Module Transmitting Data I/O Allocation Examples The Alarm when s Error Occurs Using the Board Status Register the User Alarm IO Allocation and the Ladder Program Restrictions at the Time of Network Configuration Self-Configuration with MP Error Indication LED Indicators viii 8/38

9 CD MECHATROLINK-II 1 Outline 1.1 System Configuration 1 Outline This manual describes a setup which is needed in order to use the MP2110-ET3 board (manufactured by YASKAWA Electric Corporation: it is henceforth written as MP2110) by DX200 as the simle I/O slave, and the information on relation. The application of the MP2110 allows the general-purpose I/O data exchange between a MECHATROLINK-Il communication Simple I/O master station and the DX200. The MP2110 is used exclusively for a Simple I/O slave station. The MP2110 cannot be used as a Imtelligent I/O or master station. 1.1 System Configuration The following diagram shows an example of the configuration of a system with an MP2110-ET3 board. MECHATROLINK- Simple I/O Master Station External PLC (sequencer) DX200 control board Terminator MECHATROLINK- Simple I/O Slave Station MP2110-ET3 MECHATROLINK- Dedicated Cable MECHATROLINK- Slave Station Terminator * The MP2110 board does not include a MECHATROLINK-Il dedicated cable or an external terminator. NOTE When the MP2110 board is connected at the end of the network, connect the external terminator to the MP2110 board. If the terminator is not correctly connected, communications may not be performed. NOTE For the hardware on this board, the JAPMC-MC2110-ET3 made by YASUKAWA is used as it is; however, its software is dedicated to the DX200. Therefore, please surely purchase the board from the Robot Factory of our company. MECHATROLINK-II is a registered trademark of MECHATROLINK Association /38

10 MECHATROLINK-II 2 Hardware Specifications CD 2 Hardware Specifications 2.1 External View of the MP2110-ET3 Board DIP switch (S1) S2 LED BAT LED S1 LED TX LED /38

11 CD MECHATROLINK-II 2 Hardware Specifications 2.2 MP2110-ET3 Specifications 2.2 MP2110-ET3 Specifications Items Interface to external device Board mounting position Error indicator Number of transmission I/O points Specifications MECHATROLINK-II PCI slot in the DX200 Simple I/O LED indicators Number of I/O points Input: 128 Output: 128 (both in the 17-byte and 32-byte communication modes) 2.3 Specifications Specifications Physical layer Transmission speed Transmission cycle Number of bytes transmitted (Partial information) Maximum number of connected to the slave device Max. transmission distance Minimum distance between stations Connecting form Transmission cable Terminator Settable Station Number Equivalent to RS Mbps 1 msec/1.5 msec/2 msec/4 msec 17 byte/32 byte Maximally 30 The entire 50 m (100 m: When using a repeater) 50 cm Bus type MECHATROLINK-II dedicated cable MECHATROLINK-II dedicated terminal 60 Hex - 6F Hex 2.4 Supported Commands The MP2110 supports the following commands. Command Code(Hex) Meaning MDS 04 Reading the slave station ID CDRW 03 Link transmission : transmit the output data of a master station /38

12 MECHATROLINK-II 3 Setting and Mounting the MP2110 Board CD 3 Setting and Mounting the MP2110 Board WARNING Before wiring, be sure to turn OFF the power supply and put up a warning sign, such as DO NOT TURN ON THE POWER. Failure to observe this warning may result in an electric shock or an injury. Do not touch the inside of the panel for 5 minutes after the power is turned OFF. The remaining charged voltage in the capacitor may cause an electric shock or an injury. Be sure to close the door and install the protection cover while the power is turned ON. Failure to observe this warning may result in a fire or an electric shock. CAUTION The wiring and mounting must be performed by authorized and qualified personnel. Failure to observe this caution may result in a fire or an electric shock. Make sure that there is no foreign matter such as metal chips on the board. In case of malfunction, etc. it may result in an injury or damage the board. Make sure that there is no damage or deflection of parts on the board. In case of malfunction, etc. it may result in an injury or damage the board. Correctly connect each cable and connector. Failure to observe this caution may result in a fire or damage the board. Set the switches, etc. correctly. Malfunction, caused by an incorrect setting, may result in an injury or damage the board. Never touch the mounting surfaces of the board parts directly with fingers. The generated static electricity may damage the IC. Never touch the soldered surfaces of the board directly with fingers. Protrusions on the soldered surface may result in an injury. No shock to the board. The shock may damage the board /38

13 CD MECHATROLINK-II 3 Setting and Mounting the MP2110 Board 3.1 Mounting the MP2110 Board 3.1 Mounting the MP2110 Board Please set a communication station number, a communication cycle, and the number of communication bytes by the DIP switches on the MP2110 board. Board Side Switch No. Table 3-1: A setting Example of the DIP Switches (S1). Meaning Settings Setting example 1 station number (bit0) 2 station number (bit1) 3 station number (bit2) 4 station number (bit3) 5 cycle (bit0) 6 cycle (bit1) 7 Number of communication bytes Please set the communication station number of the MECHATROLINK-II by stitches : 60 Hex : 6F Hex Please set the communication cycle of the MECHATROLINK-II by stitches : 1 msec 01 : 1.5 msec 10 : 2 msec 11 : 4 msec 0 : 32 byte 1 : 17 byte 8 system reservation Be sure to set the DIP switches to /38

14 MECHATROLINK-II 3 Setting and Mounting the MP2110 Board 3.2 Mount the MP2110 Board 3.2 Mount the MP2110 Board Mount the MP2110 board in the following manner CD Opening the Front Door of the DX Open the front door of DX200. (1) Turn the two door locks on the front face of the DX200 clockwise for 90 with a coin or a flat tip screwdriver. Fig. 3-1: Door Unlock clockwise 90 door lock flathead screw driver (2) With the door locks turned clockwise for 90, turn the main switch handle to the OFF position, and slowly open the door. Fig. 3-2: Open the Door "OFF" Position (Horizontal) DX200 Main power supply switch /38

15 CD MECHATROLINK-II 3 Setting and Mounting the MP2110 Board 3.2 Mount the MP2110 Board Mounting the MP2110 Board on the DX Remove the riser card from the CPU rack. 2. Insert the MP2110 board into the PCI slot of the riser card, then securely tighten the MP2110 board with the metal support. 3. Mount the riser card in the CPU rack. Fix the MP2110-ET3 board with a screw CN1 : CPU optional PCI slot1 CN2 : CPU optional PCI slot Cable Connection 1. Connect the T-branch module with the MECHATROLINK-II connector of MP2110 board. 2. Connect the MECHATROLINK-II delicated cable with the T-branch module /38

16 MECHATROLINK-II 3 Setting and Mounting the MP2110 Board 3.2 Mount the MP2110 Board CD Closing Front Door of the DX200 Close the front door of DX200. (1) Close the door gently. (2) Turn the two door locks on the front face of the DX200 counterclockwise for 90. Fig. 3-3: Lock the Door clockwise 90 door lock flathead screw driver CAUTION Always close the door of the controller (DX200) except for maintenance. Make sure to rotate all the door locks counterclockwise. If dust or water enters inside the controller, electric shock or breakdown of DX200 may result /38

17 CD MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module 4.1 Setting of Optional Board and I/O Module In order to use the MP2110 on the DX200, perform the setting of the optional board and I/O module in the following manner. SUPPLE- MENT Set the optional board and I/O module in the management mode. In the operation mode and the editing mode, the settings are for reference only. 1. Turn ON the power supply while pressing [MAIN MENU]. The main menu appears. 2. Set the security mode to the MANAGEMENT MODE. 3. Select {SYSTEM} under the main menu. The sub menu appears /38

18 MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module CD 4. Press {SETUP}. The SETUP display appears. 5. Select "OPTION BOARD". The OPTION BOARD display appears. 6. Select "MP2110". The MP2100 setup display appears /38

19 CD MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module Explanation of Setup Items MP2110 Sets whether to use the MP2110 or not. Set "USED". IO SIZE 18 bytes are displayed. It cannot be changed. 7. Press [ENTER]. The confirmation dialog box appears. 8. Press "YES". The IO MODULE display appears /38

20 MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module CD 9. Press [ENTER]. The rest of the I/O module display appears, and "MP2110" is displayed. 10. Press [ENTER]. The confirmation dialog box appears. 11. Select {Yes}. If the IO module is properly installed, select {YES}. The IO module settings will be updated, and the external IO setup window is displayed /38

21 CD MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module 12. The external IO setup window will be displayed. 13. Select {AUTO} or {MANUAL} for the allocation mode. After {AUTO}/{MANUAL} is selected, the selection menu is displayed. NOTE If the allocation mode is changed from {MANUAL} to {AUTO}, the allocation data that has been set will be lost, and re-allocating will be executed in the auto mode. If the set allocation data need to be kept, save the data in the external memory menu in advance /38

22 MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module CD 14. Select the allocation mode to be set. When allocating the I/O signal automatically, select {AUTO}. When allocating the I/O signal manually, select {MANUAL}. The selected allocation mode will be set. 15. Select {DETAIL} of {EXTERNAL IO ALLOCATION}. When selecting {AUTO} for the allocation mode, the following steps are not necessary. Perform the operation from step 19. When selecting {MANUAL} for the allocation mode, perform the following steps for the items necessary for manual settings /38

23 CD MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module 16. Select the external I/O signal number to be changed from the original. ("#20060" is selected in the setting example.) The select menu is displayed. 17. Select {MODIFY} and enter the desired external input signal number to replace the original. ( is entered in the setting example.) The external input signal number will be changed. 18. Select and change the external input signal number with the same steps. Repeat the selecting and changing operation for the desired allocation /38

24 MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module CD 19. Press [ENTER]. The external output signal allocation window is displayed. 20. Select and change the external output signal number with the same procedure as the external input signal number. Repeat the selecting and changing operation for the desired allocation. 21. Press [ENTER]. The confirmation dialog box is displayed /38

25 CD MECHATROLINK-II 4.1 Setting of Optional Board and I/O Module 22. Select {Yes}. Return to the setting window after the setting contents are confirmed /38

26 MECHATROLINK-II 4.2 Transmitting Data 4.2 Transmitting Data CD The data to be transferred from the MP2110 to the inside of the DX200 is input/output data to be transmitted to master station MECHATROLINK-II. In this data, contact point data and status data (input/output each 16 points=2-byte) of the MP2110 are contained. The region for the status data cannot transmit/receive the contact point data. The transmission data from the MP2110 are allocated to the external I/O signals of concurrent I/O. Concurrent IO < Input > to (4096 inputs) < Output > to (4096 outputs) MP2110 MECHATROLINKcommunications and transfer to the DX200 Master Station MECHATROLINK- MECHATROLINKcommunications If only the MP2110 is mounted as an optional I/O board, a concurrent I/O of each board is assigned as follows. (20010 to are used for the standard I/O unit of the DX200.) /38

27 CD MECHATROLINK-II 4.2 Transmitting Data Table 4-1: I/O Allocation Examples for DX200 (For Handling) Note 1) The following allocation examples are in case of the standard setting. If the external input/output signal allocation or concurrent ladder program is changed, the allocation will be changed according to the content changed. Note 2) Regarding the detail of input data/output data on JANCD-YIO21-E (Standard I/O Board), refer to DX200 Instructions. Note 3) Regarding JANCD-YIO21-E (standard I/O board), YSF21 (YIO21 base board) is displayed on IO Module Setup display. JANCD-YIO21-E (Standard I/O) EtherNet/IP (Standard LAN Port) I/O Input External Input Signal General Input Signal Description None (Already allocated with the system) Input Data (1) None (Already allocated with the system) Input Data (2) (IN IN0008) Input Data (3) (IN IN0016) Input Data (4) None (Already allocated with the system) Input Data (5) I/O Output External Output Signal General Output Signal Description None (Already allocated with the system) Output Data (1) None (Already allocated with the system) Output Data (2) (OT OT0008) Output Data (3) (OT OT0016) Output Data (4) None (Already allocated with the system) Output Data (5) I/O Input External Input Signal General Input Signal Description (IN IN0024) Board Status IO allocation is invalid. 1) (IN IN0032) Board Status IO allocation is invalid. 1) (IN IN0040) Input Data (1) (IN IN0048) Input Data (2) (IN IN0056) Input Data (3) (IN IN0064) Input Data (4) (IN IN0072) Input Data (5) (IN IN0080) Input Data (6) (IN IN0088) Input Data (7) (IN IN0096) Input Data (8) (IN IN0104) Input Data (9) (IN IN0112) Input Data (10) (IN IN0120) Input Data (11) (IN IN0128) Input Data (12) (IN IN0136) Input Data (13) (IN IN0144) Input Data (14) (IN IN0152) Input Data (15) (IN IN0160) Input Data (16) I/O Output External Output Signal General Output Signal Description (OT OT0024) System Reservation IO allocation is invalid. 1) (OT OT0032) System Reservation IO allocation is invalid. 1) (OT OT0040) Output Data (1) (OT OT0048) Output Data (2) (OT OT0056) Output Data (3) (OT OT0064) Output Data (4) (OT OT0072) Output Data (5) (OT OT0080) Output Data (6) (OT OT0088) Output Data (7) (OT OT0096) Output Data (8) (OT OT0104) Output Data (9) (OT OT0112) Output Data (10) (OT OT0120) Output Data (11) (OT OT0128) Output Data (12) (OT OT0136) Output Data (13) (OT OT0144) Output Data (14) (OT OT0152) Output Data (15) (OT OT0160) Output Data (16) 1 The board status and system reservation cannot be allocated as the IO signal. The data are not transmitted from MP2110-ET3 (cannot communicate with higher PLC) /38

28 MECHATROLINK-II 4.2 Transmitting Data CD Table 4-2: I/O Allocation Examples for DX200 (Except for Handling) Note 1) The following allocation examples are in case of the standard setting. If the external input/output signal allocation or concurrent ladder program is changed, the allocation will be changed according to the content changed. Note 2) Regarding the detail of input data/output data on JANCD-YIO21-E (Standard I/O Board), refer to DX200 Instructions. Note 3) Regarding JANCD-YIO21-E (standard I/O board), YSF21 (YIO21 base board) is displayed on IO Module Setup display. JANCD-YIO21-E (Standard I/O) EtherNet/IP (Standard LAN Port) I/O Input External Input Signal General Input Signal Description None (Already allocated with the system) Input Data (1) None (Already allocated with the system) Input Data (2) (IN IN0008) Input Data (3) (IN IN0016) Input Data (4) (IN IN0024) Input Data (5) I/O Output External Output Signal General Output Signal Description None (Already allocated with the system) Output Data (1) None (Already allocated with the system) Output Data (2) (OT OT0008) Output Data (3) (OT OT0016) Output Data (4) (OT OT0024) Output Data (5) I/O Input External Input Signal General Input Signal Description (IN IN0032) Board Status IO allocation is invalid. 1) (IN IN0040) Board Status IO allocation is invalid. 1) (IN IN0048) Input Data (1) (IN IN0056) Input Data (2) (IN IN0064) Input Data (3) (IN IN0072) Input Data (4) (IN IN0080) Input Data (5) (IN IN0088) Input Data (6) (IN IN0096) Input Data (7) (IN IN0104) Input Data (8) (IN IN0112) Input Data (9) (IN IN0120) Input Data (10) (IN IN0128) Input Data (11) (IN IN0136) Input Data (12) (IN IN0144) Input Data (13) (IN IN0152) Input Data (14) (IN IN0160) Input Data (15) (IN IN0168) Input Data (16) I/O Output External Output Signal General Output Signal Description (OT OT0032) System Reservation IO allocation is invalid. 1) (OT OT0040) System Reservation IO allocation is invalid. 1) (OT OT0048) Output Data (1) (OT OT0056) Output Data (2) (OT OT0064) Output Data (3) (OT OT0072) Output Data (4) (OT OT0080) Output Data (5) (OT OT0088) Output Data (6) (OT OT0096) Output Data (7) (OT OT0104) Output Data (8) (OT OT0112) Output Data (9) (OT OT0120) Output Data (10) (OT OT0128) Output Data (11) (OT OT0136) Output Data (12) (OT OT0144) Output Data (13) (OT OT0152) Output Data (14) (OT OT0160) Output Data (15) (OT OT0168) Output Data (16) 1 The board status and system reservation cannot be allocated as the IO signal. The data are not transmitted from MP2110-ET3 (cannot communicate with higher PLC) /38

29 CD MECHATROLINK-II 4.2 Transmitting Data *In the MP2110, if the number of the communication bytes is set to either byte of 17-byte and 32-byte, the regions to be secured for external input/ output signals become the 18 byte. [MP2110 board status] The head 2-byte of the input data to the MP2110 assigned to the external input signals ( and in the aforementioned assignment example) shows the board status of the MP2110. Normal values Abnormal values Board status (1) station 0xff number (0x60-0x6f) Board status (2) Control code(0x03, 0x04) Other than the matters described above /38

30 MECHATROLINK-II 4.3 I/O Allocation Examples 4.3 I/O Allocation Examples CD The external I/O signals allocation of the board is shown in the following table. Example 1: When only the MP2110 is mounted Input : YIO : MP2110 Output : YIO : MP2110 Example 2: When only the XOI01 + MP2110 is mounted Input : YIO : XOI : MP2110 Output : YIO : XOI : MP /38

31 CD MECHATROLINK-II 4.4 The Alarm when s Error Occurs Using the Board Status 4.4 The Alarm when s Error Occurs Using the Board Status When the optional board detects the communication error, by using the CIO ladder or the user alarm allows to occur the alarm. The examples of the method are described in below. The alarm to be occurred is "MP2110 COMMUNICATION ERROR". As for the user alarm registration, refer to Section 13.7 I/O Messages and I/O Alarms in the Dx200 OPTIONS INSTRUCTIONS FOR CONCURRENT I/O ( CD) for more details. [Alarm No.] Alarm Name [9065] MP2110 COMMUNICATION ERROR Signal No. Meaning of Alarms (Board Status Signal) to MP2110 board s status is abnormal. When the optional board detects and alerts the error by the board status signal, the ladder program, which raises an alarm, is created according to the error signal. The procedures to register the alarms above as the user alarm and the ladder program, which alert an alarm, are described below /38

32 MECHATROLINK-II CD 4.4 The Alarm when s Error Occurs Using the Board Status Register the User Alarm 1. Change the security mode to the Management Mode. 2. Select the {I/O ALARM} from the {IN/OUT} in the main menu. 3. The I/O alarm (system) window appears. 4. Press the [PAGE]. I/O alarm (user) window appears. 5. Move the cursor over the desired No. to register, and press [SELECT]. The window changes to the character string entry window /38

33 CD MECHATROLINK-II 4.4 The Alarm when s Error Occurs Using the Board Status 6. Enter the I/O alarm name. 7. Press [ENTER]. The entered alarm is registered /38

34 MECHATROLINK-II CD 4.4 The Alarm when s Error Occurs Using the Board Status IO Allocation and the Ladder Program Create the ladder program to alert the alarm by using the following signals when the optional board detects an error. External input Signal Description to Station Number At normal state: 0x60-0x6f At error state: 0xff System input signal Signal Description User part alarm requirement User part alarm code d User part alarm code d User part alarm code d User part alarm code d User part alarm code d User part alarm code d5 Assistant relay Signal Description Turned ON the control power supply (continuously ON) /38

35 CD MECHATROLINK-II 4.4 The Alarm when s Error Occurs Using the Board Status The ladder program (the figure of the ladder) Creating the following ladder allows to alert the alarm according to the status error signals of the optional board. #20060 #20061 #20062 #20063 #20064 #20065 #20066 #20067 #40220 #70017 #40221 #70017 #40222 #70017 #40223 #70017 #40224 #70017 #40225 #20060 #20061 #20062 #20063 #20064 #20065 #20066 #20067 # /38

36 MECHATROLINK-II 5 Restrictions at the Time of Network Configuration 5.1 Self-Configuration with MP CD 5 Restrictions at the Time of Network Configuration 5.1 Self-Configuration with MP2310 After self-configuration is performed with MP2310, "JEPMC-IO2310/30" may be displayed for the MP2110. This is because the MP2110 has the same communication specifications as JEPMC-IO2310/30. This is just a display restriction. As communication will be normally performed, use the board without modification /38

37 CD MECHATROLINK-II 6 Error Indication 6.1 LED Indicators 6 Error Indication 6.1 LED Indicators Four LEDs are provided on the front of the MP2110 board to indicate the status of board. LED Indicator (Color) S1 (Green/Red) S2 (Green/Red) TX (Green) BAT (Red) Meaning of LED LED Status Meaning of LED Status Board status Unlit Not powered. Lit in red The MP2110-ET3 board setup incomplete. status Sending data (communication state in IC level) Brink in green (Normal) Unlit Lit in green (Normal) Unlit Brink in green (Normal) The MP2110 board is operating normally. Not powered. MECHATROLINK communication was started. MECHATROLINK communication is not done. MECHATROLINK communication is being continued. Battery status Unlit LED is always unlit because the battery has not mounted to the MP2110 board. S2 LED S1 LED BAT LED TX LED /38

38 DX200 OPTIONS MECHATROLINK-II COMMUNICATION FUNCTION INSTRUCTIONS (FOR MP2110-ET3 MADE BY YASKAWA ELECTRIC CORPORATION ) Specifications are subject to change without notice for ongoing product modifications and improvements. MANUAL NO. 0 38/38