1U Device Expansion Unit Configuration Guide

Transcription

1 1U Device Expansion Unit Configuration Guide Introduction This document contains product and configuration information that will enable you to configure your system. The guide will ensure fast and proper configuration of your storage system. August 30, 2017 Revision 3.0 NEC Corporation

2 Contents TECHNICAL SPECIFICATION... 3 Key Features... 3 Specification... 3 EXTERNAL VIEWS... 4 Front and Rear Views... 4 Dimensions (mm)... 5 UNIT CONFIGURATION External Tape Drive Enclosure Tape Drive Configuration SAS Tape Drive Configuration USB RDX Drive Configuration SAS and USB Tape/RDX Drive Configuration COPYRIGHT NOTICE AND LIABILITY DISCLAIMER REVISION HISTORY NEC Corporation Revision 3.0 August,

3 Technical Specification Key Features Affordable direct attached data protection solution for rack mount systems Two 5-inch half height drive bays in 1U enclosure Flexible configuration with SAS and USB tape drive installation Superior reliability with redundant power supplies Specification Model 1U Device Expansion Unit Part Number 5-inch Media Bays 2 Redundant Power Supply Power Supply Dimensions (W x D x H ) Maximum Power Consumption Maximum Weight N F Optional, non-hot plug VAC ± 10% 50 / 60 Hz ± 3 Hz x x 44.0 mm / 16.7 x 22.7 x 1.7 in (1U) 328VA 6.1 kg, lbs. Temperature, Relative Humidity (non-condensing) Operating: 10 to 40 C / 50 to 104 F, 10 to 80% Non-Operating: -10 to 55 C / 14 to 131 F, 10 to 80% NEC Corporation Revision 3.0 August,

4 External Views Front and Rear Views Front View A B C D E I F G H I Legend A. Power Switch 1 F. Error Status LED B. Ready LED G. Power Unit 2 Status LED C. Power Unit 1 Status LED H. Fan Unit 2 Status LED D. Fan Unit 1 Status LED I. Drive Bays E. Power Switch 2 Rear View B A C D E Legend A. AC Inlet D. External Connector 1 B. AC Inlet (Optional) E. External Connector 3 C. External Connector 2 NEC Corporation Revision 3.0 August,

5 CONFIGURATION GUIDE 1U Device Expansion Unit Dimensions (mm) NEC Corporation Revision 3.0 August,

6 Unit Configuration 1 External Tape Drive Enclosure 1.1 Tape Drive Configuration Refer to the section in accordance with type of tape drives installed and number of host adapters. Type of Tape Drives Number of Host Adapters Section Internal LTO One SAS HBAs Two SAS HBAs Internal RDX One USB HBAs Two USB HBAs Mixing internal LTO and RDX Drives One SAS and one /USB HBAs 1.4 The tape drive enclosure can be shared with up to two servers, HBAs. See the figures below for typical tape drive bays configuration. Two HBA Configuration To HBA To HBA SAS Interface SAS Interface NEC Corporation Revision 3.0 August,

7 1.2 SAS Tape Drive Configuration One SAS HBA Connection Diagram Server Device Expansion Unit PCI Slot Internal Bay #1 Bay #2 P2 Redundant Power Supply Product List Category Product Name / Description Part Number Storage Controller Enclosure Power Supply Recommended Drive 2 slots available LSI SAS9212-4i4e Host Bus Adapter 6Gb/s SAS, Int. 4 / Ext. 4, 7-pin SATA / SFF-8088, PCIe 2.0 x8 1 x LSILogic SAS9300-8e 12Gb/s SAS, 8(SFF-8644), PCIe3.0(x8) 12Gb/s SAS, Ext. 8(SFF-8644), PCIe3.0(x8) LSI SAS9300-8e 12Gb/s SAS, Ext. 8(SFF-8644), PCIe3.0(x8) External 2 m, 1 x SFF-8088 to 1 x SFF-8088 External SAS cable 2 m, 1x Mini SAS HD -1x Mini SAS 1U Device Expansion Unit 2 x 5-inch media bays Power Unit non-hot plug power supply Internal 1 x SFF-8088 to 2 x SFF-8482, mount bracket included LTO3, Half height, Native capacity 400 GB LTO4, Half height, Native capacity 800 GB LTO5, Half height, Native capacity 1.5 TB LTO6, Half height, Native capacity 2.5 TB LTO7, Half height, Native capacity 6 TB LTO5, Half height, Native capacity 1.5 TB LTO6, Half height, Native capacity 2.5 TB LTO7, Half height, Native capacity 6 TB N N N N K (02) K (02) N F N F K (00) N N N N N N N N Refer to the system configuration of the server to select the appropriate SAS controller and internal LTO drive. Choose the appropriate SAS cable as follows: K (02): N K (02): N , N , and N NEC Corporation Revision 3.0 August,

8 1.2.2 Two SAS HBA Connection Diagram Server Device Expansion Unit PCI Slot PCI Slot Internal Bay #1 Bay #2 P2 Redundant Pow er Supply Product List Category Product Name / Description Part Number Storage Controller 2 2 Enclosure Power supply Recommended 2 Drive 2 slots available LSI SAS9212-4i4e Host Bus Adapter 6Gb/s SAS, Int. 4 / Ext. 4, 7-pin SATA / SFF-8088, PCIe 2.0 x8 1 x LSILogic SAS9300-8e 12Gb/s SAS, 8(SFF-8644), PCIe3.0(x8) 12Gb/s SAS, Ext. 8(SFF-8644), PCIe3.0(x8) LSI SAS9300-8e 12Gb/s SAS, Ext. 8(SFF-8644), PCIe3.0(x8) External 2 m, 1 x SFF-8088 to 1 x SFF-8088 External SAS cable 2 m, 1x Mini SAS HD -1x Mini SAS 1U Device Expansion Unit 2 x 5-inch media bays Power Unit non-hot plug power supply Internal 1 x SFF-8088 to 2 x SFF-8482, mount bracket included LTO3, Half height, Native capacity 400 GB LTO4, Half height, Native capacity 800 GB LTO5, Half height, Native capacity 1.5 TB LTO6, Half height, Native capacity 2.5 TB LTO7, Half height, Native capacity 6 TB LTO5, Half height, Native capacity 1.5 TB LTO6, Half height, Native capacity 2.5 TB LTO7, Half height, Native capacity 6 TB N N N N K (02) K (02) N F N F K (00) N N N N N N N N Refer to the system configuration of the server to select the appropriate SAS controller and internal LTO drive. Choose the appropriate SAS cable as follows: K (02): N K (02): N , N , and N NEC Corporation Revision 3.0 August,

9 1.3 USB RDX Drive Configuration One USB Port Connection Diagram Server USB Connector USB Cable Bay #1 Bay #2 P2 Device Expansion Unit Redundant Power Supply Product List Category Product Name / Description Part Number Storage Controller USB Cable Enclosure Power Supply Recommended Drive 1 slot available External USB Controller 1 x USB port External USB Cable USB 2.0, 2 m, 1 x external USB to 1 x USB device, mount bracket included External USB Cable USB3.0,1.17 m, 1 x external USB to 1 x USB device, mount bracket included - The cable is required to connect with a USB3.0 port. 1U Device Expansion Unit 2 x 5-inch media bays Power Unit non-hot plug power supply (Standard) K (00) K (1A) N F N F Internal RDX (USB) N Internal RDX (USB) N Choose the appropriate USB cable according to the USB connector on the server. Refer to the system configuration of the server to select the appropriate internal RDX drive. NEC Corporation Revision 3.0 August,

10 1.3.2 Two USB Ports Connection Diagram Server USB Connector USB Cable Bay #1 Bay #2 P2 Device Expansion Unit Redundant Pow er Supply USB Connector USB Cable Product List Category Product Name / Description Part Number Storage Controller USB Cable 2 Enclosure Power Supply Recommended Drive 1 slot per HBA available External USB Controller 1 x USB port External USB Cable USB 2.0, 2 m, 1 x external USB to 1 x USB device, mount bracket included External USB Cable USB3.0,1.17 m, 1 x external USB to 1 x USB device, mount bracket included - The cable is required to connect with a USB3.0 port. (Standard) K (00) K (1A) 1U Device Expansion Unit N F 2 x 5-inch media bays Power Unit N F non-hot plug power supply Internal RDX (USB) N Internal RDX (USB) N Choose an appropriate USB cable according to the USB connector on the server. Refer to the system configuration of the server to select the appropriate internal RDX drive. NEC Corporation Revision 3.0 August,

11 1.4 SAS and USB Tape/RDX Drive Configuration Connection Diagram Server Device Expansion Unit PCI Slot Internal Bay #1 Bay #2 P2 Redundant Pow er Supply USB Connector USB Cable Product List Category Product Name / Description Part Number Storage Controller Storage Controller USB Cable Enclosure Power Supply Recommended Drive 1 slot per HBA available LSI SAS9212-4i4e Host Bus Adapter 6Gb/s SAS, Int. 4 / Ext. 4, 7-pin SATA / SFF-8088, PCIe 2.0 x8 1 x LSILogic SAS9300-8e 12Gb/s SAS, 8(SFF-8644), PCIe3.0(x8), Low Profile / Full Height 12Gb/s SAS, Ext. 8(SFF-8644), PCIe3.0(x8) LSI SAS9300-8e 12Gb/s SAS, Ext. 8(SFF-8644), PCIe3.0(x8) External USB Controller 1 x USB port External 2 m, 1 x SFF-8088 to 1 x SFF-8088 External SAS cable 2 m, 1x Mini SAS HD -1x Mini SAS External USB Cable USB 2.0, 2 m, 1 x external USB to 1 x USB device, mount bracket included External USB Cable USB3.0,1.17 m, 1 x external USB to 1 x USB device, mount bracket included - The cable is required to connect with a USB3.0 port. N N N N (Standard) K (02) K (02) K (00) K (1A) 1U Device Expansion Unit N F 2 x 5-inch media bays Power Unit N F non-hot plug power supply Internal K (00) 1 x SFF-8088 to 2 x SFF-8482 LTO N LTO3, Half height, Native capacity 400 GB N LTO4, Half height, Native capacity 800 GB N LTO5, Half height, Native capacity 1.5 TB N LTO6, Half height, Native capacity 2.5 TB N LTO7, Half height, Native capacity 6 TB N LTO5, Half height, Native capacity 1.5 TB N LTO6, Half height, Native capacity 2.5 TB N LTO7, Half height, Native capacity 6 TB RDX Internal RDX (USB) N NEC Corporation Revision 3.0 August,

12 Internal RDX (USB) N Refer to the system configuration of the server to select the appropriate SAS controller and internal LTO drive. Choose the appropriate SAS cable as follows: K (02): N K (02): N , N , and N Choose an appropriate USB cable according to the USB connector on the server. Refer to the system configuration of the server to select the appropriate internal RDX drive. NEC Corporation Revision 3.0 August,

13 Copyright Notice and Liability Disclaimer The information contained herein is subject to change without notice. All other products, brands, or trade names used in this document are trademarks or registered trademarks of their respective holders. NEC shall not be liable for technical or editorial errors or omissions contained herein. NEC Corporation Revision 3.0 August,

14 Revision History Revision Date Description 3.0 August 30, 2017 New products added: / N / N / N Internal RDX (USB) / N Others: Added and cable information for new servers. 2.0 July 20, 2016 New products added: / N Others: Added and cable information for R320e. 1.0 October 23, 2015 Initial release NEC Corporation Revision 3.0 August,