Wal-Mart Universal Monitor Stand Installation Manual

Transcription

1 Wal-Mart Universal Monitor Stand Installation Manual CIM /14/16

2 Refer to the illustrated instructions below to convert the Universal Monitor Stands from Single to Dual version, and Left Hand to Right Hand versions for both Mainline and Speedy check lanes before installing on the conveyor or cabinet. Attachment hardware is included with each Universal Monitor Stand. Refer to the hardware specifications on page #3. The Universal Monitor Stand will be shipped as a Single Monitor Left Hand Version (as shown below). To convert the Monitor Stand to a Dual or Right Hand (Mainline or Speedy) version, follow the appropriate instructions designated for each configuration. If you require assistance with the conversion or installation, please call the Pan Oston Field Operations Department at

3 Configuration Reference Page Version Page BM KIT Universal Accessory Kit 3 QR Code Information 4 Hardware Kit \ Tools Required 5 Convert Single Left Hand Stand to Single Right Hand Stand 6-14 Convert Single Monitor Stand to Dual Monitor Stand (Left \ Right Hand) Installation of Monitor Stand to belted Check lanes Installation of Monitor Stand to Speedy lanes Installation of Monitors and EFT Card Reader

4 BM KIT Article Number:

5 QR CODE INFORMATION The checkout lanes and accessory kits have a QR code that may be read with a standard QR codereader app on a cell phone. The purpose of the QR code is to provide a link to documentation pertaining to the installation of the checkstands. 4

6 Universal Monitor Stand Hardware Kit The Hardware Kit is made up of machine screws and star washers designated for the components that are to be removed or repositioned depending on the different configurations (Single or Dual Monitor, Left Hand or Right Hand, Belted or Speedy Lanes). Refer to the installation instructions below in regard to the correct hardware required. A Square head drive and Phillips head screwdriver will be needed to perform this installation. Quantity of 2 ¼-20 x 1 ¼ Machine Screw Quantity of 8 ¼-20 x ¾ Machine Screw Quantity of 8 M4 x 12mm Machine Screw Quantity of 10 1/4 Star Washer 5

7 Universal Monitor Stand Single Left Hand Follow the steps below to convert the Single Left Hand version to the Single Right Hand version. 6

8 STEP 1: Remove the (7) ¼-20 machine screws\washers, from both sides and top, which attaches the existing check shelf to the monitor base. Relocate the check shelf to the opposite side of the monitor base to create a Right Hand version. Check Shelf (7) Mounting Screws\Washers Monitor Base 7

9 STEP 2: Mount the check shelf to the opposite side of the Monitor Base using the same (7) ¼-20 machine screws \ washers previously removed in STEP 1. 8

10 STEP 3: When converting the Monitor Stand from a Left Hand version to a Right Hand version, the check shelf must be repositioned to have the overhang on the side opposite the EFT Pull Bracket (as shown by the arrows below). NOTE: The overhang position is standard regardless of orientation (Left Hand or Right Hand). Using a Phillips head screwdriver, remove the (2) mounting screws that attach the Policy Cover to the Check Shelf, then remove the Policy Cover. Policy Cover mounting screws 9

11 STEP 4: Remove the (4) ¼-20 x 1 machine screws that attach the Check Shelf to the Monitor Base, then reposition the Check Shelf where the overhang is opposite the EFT Pull Bracket then reattach with the same hardware as was removed. Insert mounting screws into the (4) holes shown 10

12 STEP 5: Reposition the Monitor Extension Bracket to attach directly to the Monitor Base by first removing the (4) ¼-20 x ½ mounting screws\washers (as shown below). 11

13 STEP 6: Remove the (4) ¼-20 x ½ machine screws\washers that attach the Monitor Extension Bracket to the Monitor Base. 12

14 STEP 7: Reattach the Monitor Mount to the Monitor Base using the same (4) ¼-20 x ½ machine screws \ washers previously removed. 13

15 The Single Right Hand Monitor Stand will look like this upon completion of the conversion. Repeat the above Steps in reverse order to convert back a Single Right Hand Monitor Stand. Universal Monitor Stand Single Right Hand Version 14

16 Universal Monitor Stand Single to Dual ( Left Hand Version) Follow the steps below to convert the Universal Monitor Stand - Single Left Hand version to the Dual Left Hand version. Refer to the Single Left to Single Right Hand instructions on pages (4 through 12) to reposition the Check shelf and Monitor plate (Cashiers side) STEP 1: Reposition the Check Shelf to the extended position by first removing the (7) ¼-20 x ½ machine screws \ washers (as shown below). 15

17 STEP 2: Extend the Check Shelf outward and align the mounting holes with the open threaded rivet nuts at the end of the Monitor Base. Attach the Check Shelf to the Monitor Base using the (7) ¼-20 x ½ machine screws previously removed. 16

18 STEP 3: Remove the (4) # 8-32 x ½ machine screws that attach the EFT Pull Bracket to the EFT Riser Bracket as shown then remove the EFT Riser Bracket to access the additional (4) screws that attach the EFT Pull Bracket to the Monitor Base. Mounting Screws 17

19 STEP 4: Remove the (4) #8-32 x ½ machine screws that attach the EFT Pull Bracket to the Monitor Stand Base. Mounting Screws 18

20 STEP 5 : Align the (4) mounting holes on the Monitor\EFT Bracket, with the (4) threaded rivet nuts on the Monitor Stand Base. Rivet Nuts STEP 6: Attach the Dual Monitor plate to Monitor Stand Base using the (4) #8-32 x ½ machine screws removed in STEP 4. 19

21 STEP 7: Attach the EFT Riser Bracket to the Monitor\EFT Bracket using (4) #8-32 x ½ machine screws which are attached from behind (as shown below). Attach EFT Riser Bracket from the back side 20

22 STEP 8: The EFT ISD Adaptor Plate is NOT included as part of the Universal Monitor Stand or Hardware Kit from Pan Oston. This plate and EFT mounting hardware is supplied by Walmart ISD EFT Adaptor Plate STEP 9: Attach the EFT Adaptor Plate to the EFT Riser Bracket using (4) #8-32 x ½ machine screws. Mounting screw locations 21

23 Mounting the Universal Monitor Stand Base to the Belted Conveyor STEP 1: Place the Monitor Stand Base over the scanner end of the rail on the conveyor, aligning the inner sets of both slots (refer to the RED arrows for proper alignment) with the 3 rd and 4 th hole locations. Scanner End 22

24 STEP 2: Attach the Monitor Stand Base to the conveyor by using (2) ¼-20 x ¾ machine screws on EACH side of the rail. From the scanner end of the conveyor, use the 3 rd and 4 th hole locations - on each side as stated in STEP 1 above. Outer Mounting Screw Locations Inner Mounting Screw Locations 23

25 Mounting the Universal Monitor Stand Base to the Speedy Cabinet STEP 1: Place the Monitor Stand Base over the scanner end of the rail on Speedy cabinet, aligning both inner sets of slots (refer to the illustrations below for proper alignment) with the 1 st and 2 nd rivet nuts. From the customer side (Left) align 2 nd slot with 1 st rivet nut. From the customer side (Right) align 2 nd slot with 3 rd rivet nut 24

26 STEP 2: Place the Rail Extension into the opening at the intake end of the Monitor Stand. Ensure the end of the Rail Extension is flush with the end of the Monitor Stand. Attach the Rail Extension to the Monitor Stand using (2) ¼ -20 x ¾ machine screws. (refer to the illustrations below for proper alignment). Rail Extension is to be flush with Monitor Stand 25

27 Mounting the Touch Screen Monitor on the Cashier Side (Single or Dual Monitor) STEP 1: Place \ align the mounting holes on the backside of the monitor with the mounting holes on the Monitor Stand plate and attach with (4) #8-32 x ½ machine screws. Monitor mounting hole locations 26

28 Mounting the Touch Screen Monitor on the Customer Side (Dual Monitor Only) STEP 1: Place \ align the mounting holes on the backside of the monitor with the mounting holes on the Monitor Stand plate and attach with (4) #8-32 x ½ machine screws. Monitor mounting hole locations 27

29 STEP 2: Route the cables for the monitors (Single and Dual) through the opening in Mount Extension into the scanner well area. Opening for Monitor Cable Routing 28

30 Mounting the EFT Card Reader on the Customer Side (Single or Dual Monitor) Refer to the ISD EFT Plate instructions for EFT mounting Mounting the LED Customer Display (Single Monitor Only) STEP 1: Before mounting the LED Display to the Monitor Base Stand it will be necessary to feed the cables through the routing holes as shown below. Cable Routing Path 29

31 Cable Routing Path STEP 2: Mount the LED Customer Display to the Monitor Stand Base by using (2) ¼-20 x 1 ¼ machine screws 30

32 Completed Dual Monitor Stand Version Customer Side Cashier Side 31

33 Completed Single Monitor Stand Version Cashier Side Customer Side 32