Motorized Roller Shades
|
|
- Rosemary Kelley
- 6 years ago
- Views:
Transcription
1 Motorized Roller Shades Revision 8/7/2012 Sales/Support: Web / Catalog: Training:
2 Code and Insurance Always Follow National Code State Code Local Code National Electric Code (NEC) When No Code Exists the Code Defaults to the NEC Licensing and Insurance What are the Licenses Required? Are Employees Covered for Electrical and other Trade Work?
3 Motorized Roller Shades Action: Rolled fabric raises and lowers Power 12V DC Solar Battery Transformer 24V DC 110VAC Control RTS Wireless Contact Closure Infrared (IR) RS-485 Z-Wave ZigBee HA
4 Measuring For Roller Shades
5 Measuring For Roller Shades Tip: Use a metal tape measure. A cloth tape may stretch and distort measurements. Be sure to measure every window. Some may appear identical and often are not.
6 Inside Frame Measurement Inside mounted treatments are recessed within the window opening. When the shade is mounted inside the frame it gives a clean, custom built-in look Tip: For the shade to fit in the window frame, the jamb extension must be 2 3/4 deep or greater. For larger shades the depth may need to be 4. When ordering shades that will be mounted inside a frame it is a good idea to request a deduction. The fabricator will then take a minor deduction to the width to ensure the brackets do not bind when installed. When you fill out the shade request on-line specify the shade measurement type as inside frame and a deduction will be added to your quote.
7 Inside Frame Measurements Width (3 locations) Height Top Center Bottom Measure the width at the top, center, and bottom of the opening. Use the narrowest of the 3 measurements. Measure the height of the opening.
8 Inside Frame Shade Light Gap Dimensions may change based on motor and assembly The red line represents the light gap A motor always must be wider than the fabric The width of the opening dictates the maximum width of the motor, mounting hardware and brackets A fabricator builds the treatment based on the opening size The shade material must be narrower than the motor, there is a space between the fabric and the sides of the opening The width of the light gap varies based on a motor type and the size of the treatment The light gap on low voltage motors is typically 5/8 The light gap on a line voltage motor ranges from 1 1/8 to 1¼ The distance on both sides is not always equal (See example image) In most residential applications the light gap falls on a trim molding so the glass is fully covered
9 Inside Frame Blackout Rails + Sills For true blackout applications order a set of rails and sills Rails and sills are metal U channels mounted to the sides and bottom Blackout material falls in the U channel to block light and fill the light gap * The side rail is shown in orange to highlight it in the illustration. Rails and sills are white or brown and can be painted. They are available up to 20 long Felt / Pile 1.75 Hem Bar & Fabric Edge ride inside the channel
10 Surface Mount Shade Measurements Outside mounted treatments mount either on the wood frame or above the window They will make a window appear bigger and hide unattractive windows Use an outside mount when there is not sufficient depth for inside mounting
11 Outside Frame Measurements Height Width Outside Bracket (OB) Measurement: This is the most popular surface mount measurement technique Measure the exact area to be covered Include overlap on the surrounding wall or frame The motor mounts directly to the top molding and is built to the same width as the window and molding Cloth Measurement: The architecture of the room dictates that the cloth must cover a specific area The motor and brackets can extend past the width of the window and molding
12 Outside Bracket vs. Cloth Measurement Outside Bracket (OB) Measurement Outside Bracket (OB) The width of the motor and brackets are even with the molding outer edge There is a light gap which varies based on the motor type and size of the window treatment Cloth Measurement The motor and bracket expand beyond the sides of the window The cloth covers the area specified on the order Cloth Measurement
13 Outside Bracket Measurement Light Gap Outside Bracket (OB) Measurement Dimensions may change based on motor and assembly The red line represents the light gap A motor always must be wider the the fabric The width of the opening dictates the maximum width of the motor, mounting hardware and brackets A fabricator builds the treatment based on the molding width The shade material must be narrower than the motor, there is a space between the fabric and the sides of the opening The width of the light gap varies based on a motor type and the size of the treatment The light gap on low voltage motors is typically 5/8 The light gap on a line voltage motor ranges from 1 1/8 to 1 ¼ The distance on both sides is not equal (See example image) On request, the light gap distance can be provided with any quote In most residential applications the light gap falls on a trim molding so the glass is covered
14 Head Pockets New Construction For a hidden, professional installation use an aluminum head pocket Installs above the window The lower removable plate leaves a slot for the fabric to hang Integrated rails makes installing brackets quick and easy Order to the width of the treatment Use a 4 pocket when using 24VDC Use a 5½ pocket when using 110VAC Removable plate New Construction Head Pocket
15 Motor Options Motor Power Noise Level Control Limit Setting LT-30 12VDC Standard RTS RTS Remote ST-30DCT 24VDC Quiet Contact Closure Limit Tool ST-30RTS 24VDC Quiet RTS RTS Remote ST-30RS485 24VDC Quiet RS-485 Limit Tool Sonesse 50 RTS 110VAC Quiet RTS RTS Remote Sonesse 50 ILT 110VAC Quiet ILT (RS-485) or Contact Closure Limit Tool
16 Quoting Shades Start with the shade measurement The price in the square is referred to as the base price Choose the appropriate motor Sizes shown in gray are not available with a battery motor White = All motors 110VAC start at 36 wide Grey = 24VDC and 110VAC Black = 110VAC only
17 Quoting Shade Example Opening measurement 47 W x 73 L 110VAC power RTS (1 shade) Rails and Sills, no fascia Base Price $122 Rails ($76) + Sill ($24) $100 Motor (50 RTS) $459 Total: $681 Controls and shipping sold separately
18 Quoting Shade Fabrics Alkenz The catalog Base Price includes: 3000 NET 1% (not on the web site) 3% 5% 10% Fabric warranty for the life of the product Fabric books are $10 (shipped) If other fabrics are selected, call for a quote Brochure:
19 Quoting Shade Fabrics Mermet fabrics The catalog Base Price includes: E screen 3%, 5%, 10% Openess M screen 3%, 5% Openess Vienne 10% Geneva Twilight Blackout 5 Year Exterior or 10 year Interior Warranty Fabric swatches are $10 (shipped) If other fabrics are selected, call for a quote
20 Quoting Shade Fabrics Phifer SheerWeave fabrics The catalog Base Price includes: 3% Openess 2410, , 4650 = multiply base price by % Openess 2000, 2390, 2705, 4000, 4500, 4550, % Openess 2100, 2360 Blackout = multiply base price by = multiply base price by 1.35 Fabric swatches are $10 (shipped) Limited Fabric warranty If other fabrics are selected, call for a quote
21 110VAC Pre-wire AC Outlet Hidden by a valance Cat5 for RS-485 or contact closure Run AC wiring to the motor location. All motors recommended by Worthington Distribution only require 14/2 + GND, for the option of non-intelligent motors, run 14/3 + GND The motor wiring is traditionally hidden by a valance (not supplied) For non-rts applications run a Cat5 for control
22 Power: 12VDC Solar Power Solar charging kit: Solar Battery Charger 5 year warranty Mounts in a window and charges the battery Solar batteries must be charged before use Order a SOM Pre-installation AC charger Typical pre-installation charge is 24 hours
23 Power: 12VDC Battery or AC Re-loadable battery tube: Battery Y cable: VDC Plug-in Power Supply: Re-loadable Battery Tube Use with 8 lithium batteries ( ) For extended battery life or heavy treatments, use a Y cable to wire two tubes in parallel Dual battery wands typically extend battery life by 75 percent Add Wall Mounting Clips for the Battery Tube ( ) 1 pair Plug-In Power Supply A great solution when wires can be run
24 24VDC Pre-wire 16/2 (150 ) 14/2 (200 ) Cat5 for RS-485 or contact closure Run 16/2 for up to 150 Run 14/2 for up to 200 When shades are moving together, it is best if the wire lengths are the same Voltage drop affects motor speed For non-rts applications run a Cat5 for control
25 Power: 24VDC When installing jobs with 3 or more 24VDC motors, Somfy Power Panels are strongly recommended They save time, provide a professional installation, and have individual fuses They do have a cost premium; however, they quickly pay for themselves because they install in minutes When using RS-485, the communication ports make programming a snap Power supplies and power distribution boards are available for ala carte installations The least expensive power option is the SOM A plug-in power supply Substituting non-somfy power supplies is not recommended May be non-regulated causing voltage issues May be non-filtered leading to a noisy motor
26 ST-30 DCT / RS485 Limit Tool Setting Limits ST-30DCT and ST-RS485 Limit Setting Tool Limit Setting Tool Limit Setting Cable Connect Power Watch polarity Reversed polarity does not hurt the motor, the motor will not respond Connect the limit setting cable to the motor Wire the Limit Setting Cable to the Limit Setting Tool 1 UP (White/Blue) 2 STOP (Blue) 3 DOWN (White/Orange) 4 GND (Orange)
27 ST-30 DCT / RS485 Set Limits Up Stop Down Check the direction of rotation Press the setting tool UP button If the shade travels down, press the setting tool Stop button until the shade jogs Confirm the rotation is correct with the up button Adjust the limits Press and hold the Up button to move the shade to the desired up position Press the Stop and Down buttons and release them once the shade begins to move Press the Stop button when it is close to the desired down position Adjust the down position Press the Stop and Up buttons and release them when the shade begins to move The shade will move and stop at the upper limit Confirm the end limits by pressing and holding the Stop button until the shade jogs
28 Factory Defaulting the ST-30 Motor Hold all 3 for 3 jogs If the motor is not behaving correctly it is possible the limits are scrambled (bottom is above the top) Factory default the motor Stop the motor Hold all 3 buttons in simultaneously The motor will jog 3 times Let go of the buttons The motor is at default, set the limits
29 Sonesse 50 ILT Limit Tool Limit Setting Tool Up Down Stop Switch Setting Limits Sonesse 50 ILT Limit Setting Tool Limit Setting Tool No extra cable is needed Connect Power Connect the setting tool to the motor with the phone cable. The LED light turns on. Push the selector switch into the up position Check the direction of rotation Press the setting tool Up button If the shade travels down, press the setting tool Stop button until the shade jogs Confirm the rotation is correct with the up button Adjust the shade to the up limit location by pressing the Up or Down buttons and push the switch to its Middle position. The Up limit recorded. (continued on next slide)
30 Sonesse 50 ILT Setting Limits Limit Setting Tool (continued from previous slide) For the Down limit, slide the to the Down position Adjust the shade to the required Down limit, by pressing the Up or Down buttons Do not press the Stop button, just let go and the shade will stop. If you press the stop button by accident, the motor will reverse directions and will not function when you set the switch to the Middle position to record the Down limit New limits will need to be set. Push the selector switch to its Middle position to record the Down limit Check the upper and lower limits
31 Z-Wave Interface: Power The Somfy Z-Wave interface is compatible with ILT (110VAC) and RS-485 (24VDC) communicating motors Follow the previous slides for setting limits and setting the motor direction The cables for both motors are included The Sonesse 30 Motor configuration is powered externally by +24VDC. Using the Power cable make sure that the white wire is on the left, and the black wire is on the right +24 VDC when plugged into the interface. Apply +24 VDC to the white wire, and -24 VDC to the black wire. The interface must be mounted within thirty (30) feet of each motor head
32 Z-Wave Installation Follow the previous slides for setting limits and setting the motor direction Including the ZDMI into a Z-Wave network Upon power-up, the Inclusion LED will illuminate for five (5) seconds then turn off When the LED turns off, press the Setup button to verify motor movement Select the inclusion (add device) command on the Z-Wave programmer or remote controller Press the Setup button to include the ZDMI in the network. Verify that the Inclusion LED stays illuminated when the interface is included in the network. Excluding the ZDMI from a Network Select the exclusion (remove device) command on your Z-Wave programmer or remote controller Press the Setup button to exclude the ZDMI from the network. Verify that the Inclusion LED turns off.
33 Z-Wave Control Z-Wave Operation The ZDMI interface can be operated by 3rd party automation, handheld and PC based controllers, or by manually by pressing the Setup button The following commands are supported Light On = Window Covering UP Light Off = Window Covering DOWN Light Brighten & Dim = Shade Up & Down Light level command 0% is lower limit 100% is upper limit Values between 0% and 100% = 99 intermediate window covering positions
34 Z-Wave Factory Reset Factory Reset Sonesse 30 RS485 Motor Remove the 24VDC power from the Interface Press & hold the Setup button while plugging the 24VDC power back into the ZDMI Continue holding the Setup button, and the Inclusion LED begins to blink slowly then rapidly after 5 seconds Upon rapid blinking of the LED, release the Setup button. The LED will remain off. Sonesse 50 ILT2 Motor Unplug the motor s communications cable from the Interface. Press & hold the Setup button while plugging the motor back into the Interface. Continue holding the Setup button, and the Inclusion LED begins to blink slowly then rapidly after 5 seconds Upon rapid blinking of the LED, release the Setup button. The LED will remain off.
35 Contact Closure The ILT and ST-30 DCT motors are designed for use with normally open (N.O.) relays. Up to 3 relays are needed per motor (see ILT exception below). Wire N.O. and C to the direction and ground (C). For the ST-30 use the Limit Setting Cable For the Sonesse 50 ILT Motor use a contact closure splitter Up to 4 motors can be controlled from 1 set of control relays (up/down/stop) Without the splitter, only wire 1 motor per relay Sonesse 50 ILT Motor Without the ILT Splitter ILT Splitter Up Common Down 5VDC
36 RTS Controls: RTS Remotes Pure channel RTS Controllers Silver Lounge channel RTS Controllers Pure Silver Lounge Patio Patio The shade motor is controlled by Somfy RTS Single or 5 channel control Advantages of RTS Technology 65 foot installed range The RTS radio receiver is integrated directly into the motor Control a variety or motor types from a single device A channel can control one or many treatments with a single button press Reliable More 10 million installations worldwide 13.4 million Rolling Codes Multiple Channels
37 RTS Controls: Other RTS Remotes 16 channel RTS Controller Pure Silver Use the 16 channel controller for large installations DecoFlex WireFree wall mounted RTS keypads are available in 5,4,3,2 and 1 channel configurations There are 56 word choices for key labels available Use the DecoFlex base to create a great tabletop controller 5 channel RTS DecoFlex White Ivory Black Almond Base for DecoFlex White Silver Black
38 RTS Controls: RTS Timer / Light Control : RTS Indoor Light : Adds Temperature Sensing Somfy RTS Controls can provide simple window treatment control Use indoor light and/or temperature to control window treatment position Move window treatment positions from a handheld Chronis timer The Chronis Comfort is the easy way to control a single or group of window treatments Control up to 4 up/down positions per day 6 channel RTS Chronis Timer Pure Silver : 1 channel RTS Chronis Comfort : Chronis Comfort Sun Sensor
39 RTS Controls: RTS Integration Universal RTS Interface The Universal RTS Interface II (URTSI II) can be used to communicate between third party systems and Somfy's RTS Motors Capable of individual or group control, and can be operated via infrared remote, RS232 and RS485 (HAI) serial communication More than one URTSI II can be used in a system Start with channel 1 (not 0) Worthington Distribution offers a pre-made and tested cable for connecting an URTSI II and an HAI controller: SOMHAICBL $9.99
40 RTS Controls: Contact Closure RTS Contact closure interface (3) Dry Contacts Up / Down / Stop or Preset Momentary contact only Separate relay up, down and if applicable stop Control individual shades or a group of shades RTS Contact Closure Interface RTS Transmitter Cat No. SOM
41 RTS Controls: RTS Repeater The RTS Repeater receives the signal from an RTS transmitter and re-transmits the signal to an RTS compatible motor or receiver Simply plugs into any 120V AC electrical outlet, no programming required Should be placed at least halfway between the transmitting device such as a Telis hand-held remote and the receiving device, the motor Solves the challenge of transmitting the signal in particularly large rooms or areas One repeater can be used in an installation
42 RTS Setup - Power RTS Learning Motors are shipped in Factory Mode without limit settings and transmitter ID s Power must ONLY be connected to current window covering being programmed All other window coverings must be disconnected from their respective power while programming
43 RTS Setup Programming the Remote Up Down Programming Button Hang the treatment. Confirm it is level. Apply power. On the multi-channel remote select a channel Traditional setup is to assign channels 1 4 to shades 1,2,3 and 4. Traditionally channel 5 is used to communicate with all of the drapes as a group Place the motor in program mode On the transmitter press and hold Up and Down The shade motor will jog: A jog is a brief open/close motion Release Up and Down Confirm the motor direction using the Up and Down buttons To change motor direction Press and hold the My button, the motor will jog Set the limits (next slide)
44 RTS Setup Setting Limits Up Down Programming Button Setting the Limits The motor must be in program mode (previous slide) Move the fabric to the top position using the up and down buttons Hold my and down buttons, the shade should move in a downward direction, release the buttons If the motor stops, go back to the top and hold my and down buttons again As the shade approaches the bottom, press the my button to stop Move the shade to the lowest position and press the My and up buttons The shade will run upward and stop at the top When limits are set, hold the My button, shade will jog If there are issues setting limits, remove power for 5 seconds, apply power and start over by entering program mode (previous slide) Hold the program button on the back, the shade will jog
45 RTS Setup User Mode User Mode Setting a My position Use the up/down buttons set the shade to an intermediate position Press and hold the My button until the motor jogs Up Down
46 RTS Setup Adjusting Limits Up Down Adjusting the Limits Upper Limit Adjustment: Press the Up button, to move the shade to the limit to be re-adjusted Press and hold the Up and Down buttons simultaneously until the shade jogs Press and hold the Up or Down button to move the shade to the new desired position To confirm the new limit, press and hold the My button until the shade jogs Lower Limit Adjustment: Press the Down button, to move the shade to the limit to be re-adjusted Press and hold the Up and Down buttons simultaneously until the shade jogs Press and hold the Up or Down button to move the shade to the new desired position To confirm the new limit, press and hold the My button until the shade jogs
47 RTS Setup Add or Remove Transmitters Programming Button Select a programmed transmitter If deleting a transmitter, use a remote that will be staying in the system Press the Programming Button on the remote and the motor will jog Press the Programming Button on the remote to be added / removed and the motor will jog
48 RTS Setup Factory Reset LT-30: Return to factory default Using a paperclip, press and hold the Program Button, located on the motor head until window covering jogs 3 times, then release button All transmitters and limits will be erased ST-30: Return to factory default Press and hold the red Program Button until window covering jogs 3 times, then release button All transmitters and limits will be erased Sonesse 50 RTS: Return to factory default Remove power for 2 seconds Power for 10 seconds Remove power for 2 seconds Apply power and the shade will move All transmitters and limits will be erased
49 HAI Integration Adding the URTSII Adding the URTSII to a system Using the rotary switch, select the channel to be programmed Letter A through F stand for channels 10 through 15, 0 for 16 Do not use 0 (most installations use 1) Press the Program button on the back of an existing RTS remote Briefly press the Programming Button on the front of the URTSII The motor will jog to indicate the channel has been memorized Repeat for additional channels Use the Up/Down/Stop buttons for testing Set the dial to the channel being tested When sending serial messages the dial represents the URTSII address
50 HAI Integration HAI Setup Use RS-485 and ProLink Although the URTSII shows an RS-232 connection it is incompatible with HAI Set the Port jumper to RS-485 Worthington Distribution offers a pre-made and tested cable for connecting an URTSI II and an HAI controller: SOMHAICBL $9.99 Pro-Link Send HAI Messages to control the blind Messages UR CH DIR UR = Address: 01 to 16 (2 digits) CH = Channel: 01 to 16 (2 digits) DIR = Direction: U = Up D = Down S = Stop (Must be Capital letters) Examples: URTSII 1, Channel 1 UP: 0101U URTSII 3, Channel 12 DOWN: 0312D
51 HAI Integration: Somfy Digital Network No more than 30 SDN Network Sonesse 50 ILT 110VAC motor ILT Interface ( ) Supports up to 4 ILT motors SDN Network Somfy Digital Network (SDN) consists of both ILT (110VAC) and RS-485 (24VDC) communicating motors Both motors can be integrated on the same Cat5 network When used with a compatible 3 rd party system, SDN can provide 2-way communication, ultra-reliable performance, and flexible programming Up to 256 devices can be on a single network Each network can have up to 4000 of wire ILT Motors connect to the network through an ILT Interface ( ). The Tap MUST connect to the motor within 30.
52 HAI Integration: Somfy Digital Network ST-30 RS VDC motor SDN Network RS-485 motors do not need ILT taps Run 16/2 for up to 150 Run 18/2 for up to 200 Cat 5 for communication The Somfy power enclosures are strongly recommended Motors are individually fused Important when programming the SDN network Low Voltage power and Data boards are available for 5 or 10 motors AB -+
53 HAI Integration: Somfy Digital Network
54 HAI RS-485 SDN Connections ST-30 RS VDC motor Motor Fuses 24VDC motor power ST-30RS485 Motor Power and Data SDN Power SDN Network Ports SDN Network Ports Connection for the Worthington SOM485KIT (SDN to USB/RS-485) used for programming SDN Connection for the Worthington SOMHAICBL (HAI to SDN) When mixing RS-485 and ILT motors add 12VDC to the SDN Power port on the power distribution board to phantom power ILT taps When an installation is only ILT motors, add 12VDC to power the ILT taps Sonesse VAC motor Sonesse 50 ILT motors (30 ) 12VDC Tap power SDN Network ILT Tap for Sonesse 50 ILT motors SDN Network SOMRS485 USB to SDN Kit SOMRS485 Dip Switch Settings 485, No Echo, Term
55 Programming the SDN Network Device Manager Install the USB/RS-485 interface that comes in the Worthington SOM485KIT The driver for the USB adapter is found on the CD Browse to Click on Configuration Software Download and install ILT2-ST30 software Run the ILT2-ST30 software Under Port, choose the USB Port number Note, the Com port must be 10 or lower Click Connect
56 Programming the SDN Network 0 pulses from top = all the way up Use Up Limit to put the shade up Make certain there is one (and only one) motor powered on the SDN network 3rd Party controllers cannot be connected when reading motor addresses Once connected, click Get MTR Addr The address next to Single will be used in the HAI software (F1FCF9) Confirm the motor is communicating In the lower right corner, click Get You should see a value from the top (shade shown is up) and Limit (lower) Click Up Limit or Down Limit to run the motor and confirm limits Note, limits cannot be set in the software, see previous slides for setting limits with a limit setting tool
57 Connecting the HAI 12 VDC SDN Network SDN Ports SDN Network Move the jumper on the serial port to the right 2 pins (RS-485) Use the Worthington Distribution SOMHAICBL cable to plug into an SDN Network port The typical connection point for the SOMHAICLB will use an SDN Network port on the Somfy Power/Data board (for 24VDC) or on the ILT Tap (for 110VAC) The ILT Tap needs 12VDC A 9-12VDC power supply can be connected to the connector (labeled as 9VDC, 12VDC is OK) Phantom power from the J1 power/data board for the ST-30 (use when mixing 110VAC and 24VDC motors)
58 Programming the HAI with SDN When using Somfy SDN (Somfy Digital Network) ILT (110VAC) and RS-485 (24VDC) communicating motors set the serial port to Somfy ILT (even when using RS-485 motors) Read each motor address from the ILT2-ST30 software Remember to have 1 motor powered at a time and no 3 rd party controllers attached Under Units in the HAI, change the House Code to Somfy Name the Shade Click the far right address Type the address from the ILT2-ST30 software into the PCAccess Address Repeat for additional shades
59 Shade Movement In the ILT2 Software Movement Manual control of the shade 0 next to Down Limit is not supported Jog Not used with roller shads (tilt motor feature) Abs Position You can type in a pulse number to place the shade in a specific location Rel Position Type in a percentage from 0-100% Go to IP Go to a pre-programmed Intermediate Position (typically not used with 3 rd party controllers) Motor speed can be changed in the ST-30 motor Click ST-30 at the top and ST-30 Speed Settings will appear at the bottom GET: Get ST-30 Speeds CLEAR: Clear speeds from screen not the motor SET: Sends the speed to the motor Roll Speed: UP/DOWN Speed (6-28 RPM) Slow Speed: Not used with roller shades
60 Group addresses in the ILT2 Software Group addresses allow more than 1 shade to be controlled by a single command Group address are typically not used with 3 rd party controller, it is often easier to send level commands This slide is to document the procedure, it is only recommended when a large number of shades need to move at the exact same time Remember 1 motor powered at a time and no 3rd party controllers attached The 16 blanks under Group Addresses represent the 16 potential groups that the motor can join As the installer, you assign group numbers Each group is 6 characters from 0 F Keep things simple and use a scheme like (If you need 16 groups) Type the addresses you will need into the box(s) Press Set to send the addresses to the motor When Addresses are sent to the motor is it is a good habit to press clear and then Get to verify the values Repeat the process for each motor (one at a time)
61 Group addresses in the ILT2 Software Testing groups Connect All of the motors to the SDN Network In the ILT2 Software, click Disconnect and then Connect Type a group number into the left white box in Addressing a the top of the screen Click the button next to Group Use the Movement buttons to test the Group Communication If using an HAI (or 3 rd party equivalent) you can choose the Address Type as Group instead of Motor
62 Intermediate Positions in the ILT2 Software Pre-Sets are typically not used with 3 rd party controller, this slide is for documentation only Get Reads the current positions in the motor Clear Removes current information from the screen but not the motor IP Calculations The software automatically sets 3/4/10 or 16 IPs based on the current limits Clear All IP s removes the IPs on the screen AND in the motor Set IP s pushes the values in the IP boxes to the motor When IPs are sent to the motor is it is a good habit to press clear and then Get to verify the values
63 HAI ios Interface: SDN Network When the Somfy Digital Network is integrated with HAI, the ios interface shows the shade state and changes the movement icons to Up/Down
64 Worthington Distribution Worthington Distribution Can Provide Product Competitive Pricing Great Stocking Levels in Tafton, PA Knowledgeable, Helpful Staff Training Worthington University On-Line Technical Support System Design Support Richard Scholl President Debbie Scholl Customer Service Richie Scholl VP, Technical Sales Tricia Seybold Customer Service Manager Tom Morgan VP, Worthington University Nolan Male Technical Support Steve Hoh Technical Support Barry Hampe Technical Support
Section 8. Electronics. Switches / Switch Plates Switches operate a motorized shutter. Choice of switch is determined by style.
Section 8 Electronics Switches / Switch Plates Switches operate a motorized shutter. Choice of switch is determined by style. Transmitters Transmitters remotely operate shutters. Transmitters are capable
More informationRoller Shutter Guide. Radio Motors with Wireless Controls
Roller Shutter Guide Radio Motors with Wireless Controls Technology an integral part of everyday life Introducing the next generation roller shutter motor and control solutions from SWS UK. In todays world,
More informationDECOFLEX WIREFREE RTS SWITCH
SOMFY INSTRUCTIONS DECOFLEX WIREFREE RTS SWITCH Part # S 1810897 DecoFlex 1 (white) 1810898 DecoFlex 1 (ivory) 1810899 DecoFlex 1 (black) 1810813 DecoFlex 5 (white) 1810814 DecoFlex 5 (ivory) 1810830 DecoFlex
More informationRoller Shutter Guide. Radio Motors with Wireless Controls
Roller Shutter Guide Radio Motors with Wireless Controls Technology an integral part of everyday life Introducing the next generation roller shutter motor and control solutions from SWS UK. In todays world,
More information2012 Dealer Price List
2012 Dealer Price List Controls Home Automation 51 Jack Northrop Avenue, Hawthorne, CA 90250-4426 Tel: 10-220-2600 / 800-5-040 Fax: 10-559-9764 email: sales@smautomatic.com web: www.smautomatic.com 2012
More informationLutron Roller 100. Lutron Sivoia QS Roller 100 Chassis Specification
086106b 1 05.11.17 Lutron Roller 100 The Sivoia QS roller 100 shade utilizes the ultra-quiet, precision controlled Electronic Drive Unit (EDU). The Sivoia QS EDU is housed inside the roller shade assembly
More informationInstallation Instructions Access Dual Roller FlexShade System by Draper
Installation Instructions Access Dual Roller FlexShade System by Draper Caution 1 The Access Dual Roller FlexShade headbox is shipped in one carton; the shades and/or screen are shipped in a separate carton;
More informationControlKeeper 4. General Information. Connecting Relay Loads. Installation Sheet. Getting Started. Power Supply Wiring. Mounting the Cabinet
General Information ControlKeeper 4 Installation Sheet Model# CK4-120NO- Model# CK4-277NO The ControlKeeper-4 model is shipped in one package and is configured with either a 120V or a 277V transformer.
More informationMotorized Roller Shades
Motorized Roller Shades Motorized roller shades are available as a standalone solution, or as part of a fully automated system with Lutron Hyperion solar-adaptive technology. The precision controlled electronic
More informationRoll Up 28 RTS & WireFree Roll Up RTS Programming
Programming 1 Motor overview The motor head of the WireFree Roll Up incorporates a program button and a port for the battery pack cable. The program button is used to reset the motor to factory mode or
More informationWireless Wall Switch Guide
Wireless Wall Switch Guide Battery-Powered Window Coverings Control Like Never Before This guide shows you how to set up and operate Battery-Powered motorized products using the wireless wall switch. The
More informationCopy Machine Reader. Installation and Setup Guide
Copy Machine Reader Installation and Setup Guide CONTENTS 1 COPY MACHINE READER INSTALLATION 1 Overview 1 Reader Specifications 3 CR1120/CR1122 INSTALLATION 3 Copier Interface 3 AC Electrical 3 Communications
More informationCRAGG RAILCHARGER Instruction Manual for 10DTC-12V 20DTC-12V 30DTC-24V 40DTC-12V 60DTC-12V
CRAGG RAILCHARGER for 10DTC-12V 20DTC-12V 30DTC-24V 40DTC-12V 60DTC-12V Contents 1 Warnings, Cautions, and Notes... 1 2 Description... 2 3 Features... 2 3.1 STANDARD FEATURES... 2 3.2 CHARGER REGULATION...
More informationInstallation Instructions
Wireless Controller Miro Decorator Syle SPECIFICATIONS Power Supply... Watt Stopper Power Pack Rating..., 35mA Control outputs For Dimming Ballasts: Sink...up to 50mA Maximum voltage... 9.5VDC Minimum
More informationWhisperTrac 3000 installation guide
WhisperTrac 3000 installation guide Table of contents WhisperTrac Installation Guide Elements of the WhisperTrac system.................................................... 3 Section 1: Mounting Mounting
More informationNetworking Instructions Transform Motorized Acoustical Banner
Networking Instructions Transform Motorized Acoustical Banner Contents Introduction.......................................2 Networking Details.................................3 Banner Controls...................................7
More informationGraber Virtual Cord Fresco Roman Shades Specification
Features Graber Virtual Cord Fresco Roman Shades Specification Motorized Blind and Shade Features Refer to individual price list for specific option and size information for the product being ordered.
More informationInstallation/Operating Instructions 220V VCB Silhouette/Series E Electric Video Conferencing Background by Draper
Installation/Operating Instructions 220V VCB Silhouette/Series E Electric Video Conferencing Background by Draper Caution 1 Read instructions through completely before proceeding; keep them for future
More information6222 Two Door Module Technical Operations Manual
6222 Two Door Module Technical Operations Manual TABLE OF CONTENTS Specifications...3 Overview...4 Operations...5 Custom Access Mode...5 Standard Access Mode...5 Offline Access Mode...5 Offline Memory...5
More informationCellular Shades MOTORIZED SKYLIGHT. Simplicity with rechargeable batteries. Installation & Care Instructions
Cellular Shades MOTORIZED SKYLIGHT Simplicity with rechargeable batteries Installation & Care Instructions 152741B 7/2/2018 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill,
More information12V DC ROLLER SHADE User Manual
12V DC ROLLER SHADE User Manual English Revision 8.1 November 27th, 2017 INTRODUCTION Thank you for your purchase. The following user manual will walk you through the setup of your Link Shades device.
More informationDigital Keypad Introduction
K2 Digital Keypad Introduction The K02 uses the latest microprocessor technology to operate door strikes and security systems that require a momentary (timed) or latching dry contact closure. All programming
More informationCG800H SERIES USER MANUAL ZIGBEE WIRELESS SCENE CONTROL PANEL VERSION JANUARY, Disclaimers and Copyright
CG800H SERIES ZIGBEE WIRELESS SCENE CONTROL PANEL USER MANUAL VERSION 1.1 17 JANUARY, 2014 Disclaimers and Copyright Nothing contained in this publication is to be construed as granting any right, by implication
More informationColorMaxLP Label Roll Rewinder
ColorMaxLP Label Roll Rewinder 5/2017 INSTALLATION/OPERATOR MANUAL Included: Rewinder Base plate Power supply Power Cord Thumb screws Assembly instructions 1. Install base plate Lift front of printer and
More informationPLATINUM TECHNOLOGY. Wireless Wall Switch. Guide. for PowerRise 2.0, PowerGlide 2.0 and PowerTilt
PLATINUM TECHNOLOGY Wireless Wall Switch Guide for PowerRise 2.0, PowerGlide 2.0 and PowerTilt Control Like Never Before This guide shows you how to set up and operate Hunter Douglas motorized products
More informationOperation and Maintenance Manual
VM Series Operation and Maintenance Manual VM - Voltage Monitor VM-100-24 V VM-100-48 V VM-100-125 V VM-100-250 V EAGLE EYE POWER SOLUTIONS All Rights Reserved. 1 The Voltage Monitor series reads battery
More informationTHE SHADE STORE MOTORS WITH AMAZON ALEXA
THE SHADE STORE MOTORS WITH AMAZON ALEXA ABOUT THE SKILL: The Shade Store s motorized window treatments can be voice controlled easily through Amazon Alexa. Simple commands allow you to raise and lower
More informationUSBCNC USB Disk Key reader for CNC Controls Machine Mount instructions
USBCNC USB Disk Key reader for CNC Controls Machine Mount instructions 2008-2015 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 www.calmotion.com Introduction This
More informationCONTROL4 INTEGRATION WITH THE SHADE STORE MOTORS CONTROL4 INTEGRATION OVERVIEW:
CONTROL4 INTEGRATION WITH THE SHADE STORE MOTORS CONTROL4 INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your Savant smart home control
More information527F CNC. Retrofit controller for machines made by Fadal Machining Centers. Installation and set-up manual Calmotion LLC
527F CNC Retrofit controller for machines made by Fadal Machining Centers Installation and set-up manual 2008-2018 Calmotion LLC Calmotion LLC 7536 San Fernando Road Sun Valley, CA 91352 www.calmotion.com
More informationFlow Control. User s Guide. Programmable Dosing Pumps for Liquid Delivery, Solutions Application & Switching
Flow Control User s Guide Programmable Dosing Pumps for Liquid Delivery, Solutions Application & Switching From Single Unit to Multi-Channel Systems Manual and Software controls for Automated Operation
More informationULTRASONIC, CRUSH, MANUAL, ZEBRA, & VERTICAL LOUVRE CUTTERS
ULTRASONIC, CRUSH, MANUAL, ZEBRA, & VERTICAL LOUVRE CUTTERS IMPULSE WELDERS, END SEALER, INSPECTION HOISTS & ACCESSORIES Ultratab brings 10 plus years of experience and innovation to the window covering
More informationAB-315. ibus Wall-Dock for A-Bus Audio Systems
AB-315 ibus Wall-Dock for A-Bus Audio Systems TM By 10 The AB-315 is an on-wall ipod docking station for A-BUS audio systems. The dock connector slides in and out to adjust for any ipod and the non-skid
More informationMicro Instruments price list All pricing excludes 15%
Micro Instruments price list All pricing excludes VAT @ 15% - 2019 Product Description Solar Smart R1 Solar MPPT regulator 12/24V - 20Amp with R2 799.00 5 Way Relay board R360.00 Ethernet + SNMP support
More informationWireless Key fob, Key pad & Receiver Range
Wireless Key fob, Key pad & Receiver Range 4Ch Wireless Receiver 4x Voltage Free relay outputs (NO + NC) 100m Transmission range Multiple user codes 2 Channel wireless control Clear hinge up lid 12V DC
More informationCOMFORT CONTROL CENTER SERVICE INSTRUCTIONS
USA SERVICE OFFICE Dometic Corporation 2320 Industrial Parkway Elkhart, IN 46516 574-294-2511 CANADA Dometic Corporation 46 Zatonski, Unit 3 Brantford, ON N3T 5L8 CANADA 519-720-9578 For Service Center
More informationCompact, Low Profile High Rendering, 100% Diffusion
SURFACE MT SERIES PRELIMINARY SPECIFICATION, SUBJECT TO CHANGE WITHOUT NOTICE MT Series Compact, Low Profile High Rendering, 100% Diffusion Trimless, No Visible Hardware Trimless appearance for recessed
More information600 Series Databook. HOME MOTION by
600 Series Databook HOME MOTION by Somfy is the leading global manufacturer of strong, intelligent, quiet motors and electronic controls for interior and exterior window coverings with more than 110 million
More informationSERIES 4600 Ethernet Visual-Pager Display INSTALLATION and SPECIFICATION GUIDE. Manual No. D Revision Date: 08/2016 Control: 1.
SERIES 4600 Ethernet Visual-Pager Display INSTALLATION and SPECIFICATION GUIDE Manual No. D4600-7010 Revision Date: 08/2016 Control: 1.0 Microframe Corporation 604 South 12th Street Local: 918-258-4839
More informationRover 5. Explorer kit
Rover 5 Explorer kit The explorer kit provides the perfect interface between your Rover 5 chassis and your micro-controller with all the hardware you need so you can start programming right away. PCB Features:
More informationWhat s in the Box? REAR VIEW SAFETY
TM 1 What s in the Box? 1 Full HD Color Infra-red Weather Proof Camera 1 Full HD 7" TFT LCD Color Monitor w/monitor Mount 1 Power Harness 1 66 Camera Cable 1 Power Connection Wire 1 Screw Kit for installation
More informationTHE SHADE STORE APP SETUP INSTRUCTIONS
SETUP INSTRUCTIONS ABOUT THE APP: The Shade Store app allows for control of your motorized window treatments through your smartphone/tablet. The app allows for: Individual and group control Scene control
More informationMeasuring for BLINDS AND SHADES
Measuring for BLINDS AND SHADES FOR BLINDS AND SHADES Our measuring guide will take you through the steps you need to measure your windows. Just a few simple measurements are all you ll need and if you
More informationRТTH DUAL ROOM SWITCH
DUAL ROOM SWITCH FOR TEMPERATURE AND RELATIVE HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA
More informationPRODUCT INFORMATION MANUAL SECTION: 7E POWERRISE PLATINUM TECHNOLOGY POWERRISE PLATINUM TECHNOLOGY WIRELESS WALL SWITCH GUIDE
POWERRISE PLATINUM TECHNOLOGY WIRELESS WALL SWITCH GUIDE Control Like Never Before Control Like Never Before This guide shows you how to set up and operate LUXAFLEX Window Fashions products using the
More information527F CNC. Retrofit controller for machines made by Fadal Machining Centers. Installation and set-up manual Calmotion LLC
527F CNC Retrofit controller for machines made by Fadal Machining Centers Installation and set-up manual 2008-2018 Calmotion LLC Calmotion LLC 7536 San Fernando Road Sun Valley, CA 91352 www.calmotion.com
More informationBlue Point Engineering
Blue Point Engineering Board - Pro Module (E) Instruction Pointing the Way to Solutions! Controller I Version 2.1 The Board Pro E Module provides the following features: Up to 4 minutes recording time
More information500 Series Databook. Sonesse 50. HOME MOTION by
500 Series Databook Sonesse 50 HOME MOTION by Somfy Systems, Inc., is a global leader in the manufacturing of strong, intelligent and quiet motors for both interior and exterior window coverings. For more
More informationGeneral Programming Tips
nlight Relay Panel User & Programming Guide Installation & Troubleshooting Tips 1.1 - Powering Up Panel... 2 1.2 - LED Blink Codes On Relay Control Card... 3 1.3 - Testing Relay & Dimming Outputs... 4
More informationLCD-1 CD-LCD1-01 PRODUCT OVERVIEW. Product. Description. Specifications SKU: LCD-1. 5-Button Scene Controller
CD-LCD1-01 LCD-1 Product 5-Button Scene Controller Description The Evolve 5-Button Scene Controller is a programmable device that provides command and control of up to 5 (RF) network scenes and it s a
More informationXkitz.com. 8 Channel Capacitive Touch Switch Model XCTS-8M. Operators Manual. Invisible Touch Switch:
8 Channel Capacitive Touch Switch Model XCTS-8M Operators Manual Xkitz.com Invisible Touch Switch: The XCTS-8M allows you to install up to 8 capacitive touch switches nearly anywhere. It detects any sudden
More informationINTEGRATION OVERVIEW:
AMX Intergration AMX INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your AMX smart home control system. The integration supports isolated
More informationSeries 803 LED Product Price Display
Series 803 LED Product Price Display May 2007 Rev. 1.1 1 Installation and Operation Manual Table of contents 1. Safety.......3 2. Series 803 sign features.......4 2.1 Sign descriptions........4 2.2 Control
More informationPLATINUM TECHNOLOGY. Wireless Wall Switch. Guide. for PowerRise 2.0, PowerGlide 2.0 and PowerTilt
PLATINUM TECHNOLOGY Wireless Wall Switch Guide for PowerRise 2.0, PowerGlide 2.0 and PowerTilt Control Like Never Before This guide shows you how to set up and operate Hunter Douglas motorized products
More informationInstallation Operation
Installation Operation Luminette PowerGlide 2.0 with Platinum Technology Hard-Wired Motorization CONTENTS Getting Started: Install And Test The Headrail... 1 Understand The Connection Interface... 1 Lay
More informationAcuity Relay Panel User Guide
Acuity Relay Panel User Guide 1 of 26 Table of Contents Installation and Troubleshooting 1.1 - Powering Up the Panel... 3 1.2 - LED Blink Codes On Relay Control Card... 5 1.3 - Testing Relay and Dimming
More informationHaworth Power Technical Sheets January 2018
Haworth Power Technical Sheets January 2018 Includes Accessories This page intentionally left blank. Table of Contents Desk Top Port Power Tap Cord Power Tap Conduit Enchanced Power Module Flip Top Unit
More informationRTT2 ROOM TEMPERATURE SWITCH. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS PRODUCT DESCRIPTION ARTICLE CODES INTENDED AREA OF USE TECHNICAL DATA STANDARDS OPERATIONAL DIAGRAMS WIRING AND CONNECTIONS
More informationELAN INTEGRATION WITH THE SHADE STORE MOTORS ELAN INTEGRATION OVERVIEW:
ELAN INTEGRATION WITH THE SHADE STORE MOTORS ELAN INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your ELAN smart home control system. The
More informationPLATINUM TECHNOLOGY. Wireless Wall Switch. Guide. for PowerRise, PowerGlide and PowerTilt Systems
PLATINUM TECHNOLOGY Wireless Wall Switch Guide for PowerRise, PowerGlide and PowerTilt Systems Control Like Never Before Getting Started This guide shows you how to set up and operate Hunter Douglas motorized
More informationA-TRACK HOUSING FAMILY Semi-Custom to Meet Your Needs. Semi-Custom Offered in a variety of shapes and sizes and endless customizable options
SURFACE A-TRACK A-TRACK HOUSING FAMILY Semi-Custom to Meet Your Needs Dynamic White Semi-Custom Offered in a variety of shapes and sizes and endless customizable options End to End Connectivity Using our
More informationQuickstart Guide English ( 2 6 ) Appendix English ( 7 )
Quickstart Guide English ( 2 6 ) Appendix English ( 7 ) Quickstart Guide (English) Introduction Box Contents Solar Rocker Microphone with Cable 1/8 (3.5 mm) Stereo Aux Cable Power Cable Quickstart Guide
More informationInstruction Manual. Gold Pan Tilt Head with 12V Joystick Control Box (PT-GOLD)
Instruction Manual Gold Pan Tilt Head with 12V Joystick Control Box (PT-GOLD) All rights reserved No part of this document may be reproduced, stored in a retrieval system, or transmitted by any form or
More informationAuxBox Activation hub for integrating remote dry-contact closure triggering devices
Activation hub for integrating remote dry-contact closure triggering devices Activation hub for integrating remote dry-contact closure triggering devices instantly activates up to eight iplayer 3 or Light
More informationPIECAL 520B & 521B Thermocouple Source Operating Instructions
PIECAL 520B & 521B Thermocouple Source Operating Instructions (Shown without optional boot) Product Description (Shown with optional boot) Easy to use With the PIECAL 520B/521B you can check & calibrate
More informationThis Datasheet for the IC697CHS790. Rack, 9 Slots, Rear Mount.
This Datasheet for the IC697CHS790 Rack, 9 Slots, Rear Mount. http://www.cimtecautomation.com/parts/p-14771-ic697chs790.aspx Provides the wiring diagrams and installation guidelines for this GE Series
More informationLPG STM 94442A User s Manual
1 LPG STM 94442A User s Manual This Manual belongs to: Company: 3 Table of Contents Features....... 4 Hardware Installation...5 Monitor Mounting Dimensions.....7 Monitor Specifications...8 Sender Specifications.....9
More informationControl Panel for Swing Gates. Model: CP-12 / January 2007
Control Panel for Swing Gates Model: CP-12 / January 2007 INDEX Page 1- INTRODUCTION 3 1.1 1.2 Electrical and mechanical specification General Features 2- INSTALLATION AND SETUP 2.1.1 Installation of actuator
More informationAirTest Model CN9000 Series Sensor Controller
AirTest Model CN9000 Series Sensor Controller AirTest Model CN9000 Series Sensor Controller THEORY OF OPERATION A basic CN9000 configuration consists of Input/Process/Display combination modules, a 3 relay
More informationCOMMONLY USED 5.AFETY SENSORS. Photocell (Reflector) CLOSING Direction. Photocell (Reflector) CLOSING Direction OA4RO E.3IC-RIOIC4 EA4X IRB-RET
MLY USED 5.AFETY SENSORS 0----- OA4RO E.IC-RIOIC4 Direction. Set switch to "LIGHT ". Wire V power to photocell. Wire to photocell N0 Wire to photocell C- 4. Align photocell to reflector 5. Adjust sensitivity
More informationInstruction Manual. Hidden CCD Camera VK-1321/PIR (B&W), VKC-1338/PIR (Colour)
Instruction Manual Hidden CCD Camera VK-1321/PIR (B&W), VKC-1338/PIR (Colour) 1 Contents 1. Safety Instructions... 2 2. Description... 3 3. Installation... 4 4. Wiring Instructions... 5 5. PIR Detector
More information5000 Series Audio Matrix
5000 Series Audio Matrix FOR TECHNICAL SUPPORT CALL 513-795-5332 For more complete system information see the document 5000 Series Audio/Video System Installation & Service Manual 08-316 (11/12/13) Matrix
More informationAutomate Pulse Set-Up Instructions
Automate Pulse Set-Up Instructions ABOUT THE AUTOMATE SHADES SKILL The Automate Pulse app allows for control of your motorized window coverings through your smartphone/tablet THE APP ALLOWS FOR: Individual
More informationCamden - Key Switches
- Key Switches CM1120 - Flush Mount Key Switch 1 SPDT Momentary CM1130 - Flush Mount Key Switch 1 SPDT Maintained CM1120 CM1120 CM1120 CM2020 - Narrow Style Key Switch 1 SPDT Momentary CM2030 - Narrow
More informationSafety. Features 1 ID: Make all the connections before you plug in the main power. DMX512 Controllable and RDM Configurable
Features DMX512 Controllable and RDM Configurable Designed for driving LED strips through 6 high power 12 and 24 Volts output units available Easy addressing interface (physical switches and RDM) Isolated
More informationProScale LCD Readout Quick Start Guide
ProScale LCD Readout Quick Start Guide This Guide includes basic operation instructions for 950, General Purpose, Basic & In-Panel LCD Readouts For the Complete OPERATION Manual go to www.proscale.com/manuals.htm
More informationThe Otto Home Control app allows for control of your motorized window coverings through your smartphone/tablet
TM SET UP INSTRUCTIONS ABOUT THE OTTO HOME CONTROL APP The Otto Home Control app allows for control of your motorized window coverings through your smartphone/tablet THE APP ALLOWS FOR: Individual and
More informationSecured Series: Hub Plus Kit Single Door Controller Package Installation Manual
Secured Series: Hub Plus Kit Single Door Controller Package Installation Manual This package is designed to simplify the connections to our Secured Series Hub Plus Controller. This will translate into
More informationCO-485USB USB to RS-485 CONVERTER TECHNICAL REFERENCE
TABLE OF CONTENTS CO-485USB USB to CONVERTER TECHNICAL REFERENCE Specifications, Description and Technical Support... page 1 Connection Diagram... page 2 Set-Up & Testing... page 3 & 4 Power Supply Shunts...
More informationSERIES 5100 INSTALLATION & SPECIFICATION GUIDE
SERIES 5100 INSTALLATION & SPECIFICATION GUIDE Microframe Corporation 604 South 12th Street Local: 918-258-4839 Toll Free: Website: www.microframecorp.com E-mail: support@microframecorp.com Manual No.
More informationVBAR 270. User Manual. Version 1.2
VBAR 270 User Manual Version 1.2 VBAR 270 User Manual Page 1of 19 Introduction Thank you for purchasing VBAR 270. VBAR 270 is a LED light fixture for professional use. Using the RGB color mixing technology
More informationStandard Options. Model 4100 Position Indicating Meter. Three Phase Motor Control. Positran Transmitter
Standard Options Model 4100 Position Indicating Meter A percent-of-full-travel meter is supplied with a trim potentiometer resistor, terminal block and connectors. A potentiometer is required in the actuator
More informationRST ROOM TEMPERATURE TRANSMITTER. Mounting and operating instructions
Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE 4 TECHNICAL DATA 4 STANDARDS 4 OPERATIONAL DIAGRAM 5 WIRING AND
More informationUSER MANUAL RC-76M/RC-712M MODEL: P/N: Rev 3
KRAMER ELECTRONICS LTD. USER MANUAL MODEL: RC-76M/RC-712M P/N: 2900-300329 Rev 3 Contents 1 Introduction 1 2 Getting Started 2 2.1 Achieving the Best Performance 2 2.2 Safety Instructions 3 2.3 Recycling
More informationTOXALERT MODEL AIR 2000
TOXALERT MODEL AIR 2000 NOTE: Toxalert s Model GVU-CO 2 Sensor is the same as the Air2000R. Microprocessor-based, Infrared Environmental CO 2 Sensor OPERATOR S MANUAL TOXALERT TM INTERNATIONAL INC. P.O.
More informationTARA CONTROLS AGC-5. UCI Random Start USER S GUIDE. With Optional Warning Flashes for the Hearing Impaired. TARA CONTROLS by Cartessa Corporation
TARA CONTROLS AGC-5 UCI Random Start USER S GUIDE With Optional Warning Flashes for the Hearing Impaired TARA CONTROLS by Cartessa Corporation 4825 Cincinnati-Brookville Road Shandon, Ohio 45063 Phone:
More informationRXTH DUAL ROOM SENSOR / SWITCH
DUAL ROOM SENSOR / SWITCH FOR TEMPERATURE AND RELATIVE HUMIDITY Mounting and operating instructions Table of contents SAFETY AND PRECAUTIONS 3 PRODUCT DESCRIPTION 4 ARTICLE CODES 4 INTENDED AREA OF USE
More informationDigital Power Probes, ACL120, ACL220, ACL Internal, and DCL5 (#30015, #30023, #30024, #30025)
Digital Power Probes, ACL120, ACL220, ACL Internal, and DCL5 (#30015, #30023, #30024, #30025) This series of digital power probes by Networked Robotics is used to record a yes/no indication of the presence
More informationST-C5VRS-600 VIDEO AND RS232 EXTENDER Installation and Operation Manual
NTI R NETWORK TECHNOLOGIES INCORPORATED XTENDEX TM Series ST-C5VRS-600 VIDEO AND RS232 EXTENDER Installation and Operation Manual Manual 039 Rev. 3/13/03 WARRANTY INFORMATION The warranty period on this
More informationIf technical support is required, please contact Advent Technical Support at
Document 128-9011 Created 11/21/11 Kit Contents: Item # Qty. Component Description 1 2 Monitor Assembly 2 2 Remote Control 3 1 Cables # 3 4 1 Metal Wire Puller 5 1 Power Cord # 9 6 1 Owners Manual 7 2
More informationPowerView. Hub. by LUXAFLEX WINDOW FASHIONs
PowerView Hub by LUXAFLEX WINDOW FASHIONs quick start guide Table of Contents Kit Contents...3 Connections... 4 Home Automation Integration... 10 Troubleshooting... 11 The PowerView Hub interfaces with
More informationDigital Surveillance Camera INT SPYP. IR-B model. User s manual.
TM Digital Surveillance Camera SPYP IR-B model INT User s manual www.spy-point.com Thank you for purchasing SPYPOINT IR-B product. You can now enjoy the many benefits of a full feature and easy to use
More informationF3EM Measuring lightcurtain in robust aluminium housing
Measuring lightcurtain in robust aluminium housing F3EM Measuring lightcurtain in robust aluminium housing The F3EM provides easy to install and set up height and profile measurement. The analog output
More informationProduct and functional description
Product and functional description The RS 520/23 shutter / blind actuator is a KNX device with one relay output. The device is installed in an AP 118 Control Module Box or an AP 641 Room Control Box. The
More informationCrestron Intergration
Crestron Intergration CRESTRON INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your Crestron smart home control system. The integration
More informationEntraGuard Bronze. Quick Start Guide. Telephone Entry. 1.0 Specifications. 2.0 Unit Installation
The EntraGuard Bronze is a residential telephone keypad entry system which allows a homeowner to communicate directly with visitors and provide access by using any phone extension in the home. Because
More information8000 Series: Installation Supplement R2-1-12
8000 Series: Installation Supplement R2-1-12 Smartscan Incorporated, 33083 Eight Mile Road, Livonia MI 48152 Tel: (248) 477-2900 Fax: (248) 477-7453 Web: www.smartscaninc.com SMARTSCAN INCORPORATED Livonia,
More informationINSTRUCTION/INSTALLATION SHEET lyriq Studio High Performance Keypad
1. Introduction The, P/N AU5010-xx (see Figure 1), is an integral part of the lyriq Multi-Room Audio System. It is a component which, when combined with other essential components (a Source Input Unit,
More informationCRESTRON INTEGRATION WITH THE SHADE STORE MOTORS CRESTRON INTEGRATION OVERVIEW:
CRESTRON INTEGRATION WITH THE SHADE STORE MOTORS CRESTRON INTEGRATION OVERVIEW: Take your motorized window treatment experience to the next level by integrating them into your Crestron smart home control
More informationDLA. DMX512 Analyzer. DLA Users Manual SV2_00 B.lwp copyright ELM Video Technology, Inc.
DLA DMX512 Analyzer DLA DLA-HH 1 Table Of Contents IMPORTANT SAFEGUARDS... 2 DLA OVERVIEW... 3 CONNECTION... 3 OPERATION... 3 HARDWARE SETUP... 4 DLA-HH (PORTABLE) LAYOUT... 4 CHASSIS LAYOUT... 4 DLA MENU
More information