RocketRAID 644L / 642L

Transcription

1 淘汰 RocketRAID 644L / 642L 6Gb/s esata PCI-Express 2.0 RAID HBA For Mac User s Guide Revision: 1.0 Nov. 24, 2012 HighPoint Technologies, Inc. 1

2 Copyright Copyright 2012 HighPoint Technologies, Inc. This document contains materials protected by International Copyright Laws. All rights reserved. No part of this manual may be reproduced, transmitted or transcribed in any form and for any purpose without the express written permission of HighPoint Technologies, Inc. Trademarks Companies and products mentioned in this manual are for identification purpose only. Product names or brand names appearing in this manual may or may not be registered trademarks or copyrights of their respective owners. Backup your important data before using HighPoint's products and use at your own risk. In no event shall HighPoint be liable for any loss of profits, or for direct, indirect, special, incidental or consequential damages arising from any defect or error in HighPoint's products or manuals. Information in this manual is subject to change without notice and does not represent a commitment on the part of HighPoint. Notice Reasonable effort has been made to ensure that the information in this manual is accurate. HighPoint assumes no liability for technical inaccuracies, typographical, or other errors contained herein. 2

3 Table of Contents 1 Features and Specifications Physical Specifications Kit Contents Hardware Description and Installation RocketRAID 644L / 642L Host Adapter board layout Installing the RocketRAID 644L / 642L Host Adapter Verifying Installation RocketRAID 644L / 642L Driver Installation Driver installation Verify Installation of the Software Install / Uninstall HighPoint Web RAID Management Software Installing the Web RAID Management Software Uninstalling the Web RAID Management Software HighPoint Web RAID Management Software Running the Management Software Web RAID Management Software - Global View Web RAID Management Software - Physical Physical - Controller 1 Devices Physical - Controller 1 Devices Physical Devices Information Physical - Rescan Web RAID Management Software - Logical Logical - Create Array Logical - Spare Pool Logical - Logical Device Logical - Rescan Logical - Beeper Mute Web RAID Management Software - Setting Setting - System Setting Web RAID Management Software - Event Web RAID Management Software - SHI (Storage Health Inspector) Web RAID Management Software - Recover Web RAID Management ICON Definition List EFI EFI Update Booting MacOS X from RocketRAID 644L / 642L Adapter via EFI Thank You Customer Support

4 HighPoint RocketRAID 644L / 642L HBA For Mac HighPoint s RocketRAID 600L Series HBA s are the Industry s most affordable, high-performance, SATA 6Gb/s RAID HBA s, and are ideal for Mac Pro workstations. These 2nd Generation SATA 6Gb/s host controllers utilize a PCI-Express 2.0 host bus interface, HighPoint's Industry-proven RAID engine, and support a wide-range of single-disk and RAID configurations including 0, 1, 5, 10 and JBOD. Each RocketRAID 600L Series HBA s directly supports up to 4 SATA devices, and up to 20 when used in conjunction with port multiplier storage devices. For maximum performance, attach SATA hard drives and SSD s directly to the RocketRAID 600 s SATA and esata ports. To maximize storage capacity, use the RocketRAID 600 with port multiplier storage chassis and external disk enclosures. The HighPoint RAID Management Software provides a user friendly interface to create, manage and maintain your storage solutions. 1 Features and Specifications Hardware Specifications PCI-Express 2.0 x4 4x SATA 6Gb/s Ports Industry standard SATA/eSATA connectors Directly supports 4 SATA devices / Up to 20 with port multiplier capable enclosure Backwards compatible with HighPoint SATA RAID HBA s Low Profile (RocketRAID 640L, RocketRAID 642L) / Full Height (RocketRAID 644L) Monitor, Alerts and LED Indicators Hard Drive LED Indicators (Activity and Failed) SMTP notification for events and error reporting Alarm/Buzzer alerts for drive/array failure Advanced RAID Features RAID 0, 1, 5, 10, JBOD Redundant RAID Configuration for Array availability RAID Initialization Types - Background, Foreground, Quick Init and Keep Old Data Spin Down Idle Disk Enhanced data protection with Write Journaling feature S.M.A.R.T Support Auto Rebuild on spare drive HotPlug and HotSwap support Larger than 2 TB drive support Bootable RAID Array support via EFI Write Back or Write Through Cache support User friendly Browser-based Management Interface Web browser-based RAID management software (Web GUI) Operating System Support Mac OS X 10.5 and newer 4

5 2 Physical Specifications Dimensions: RocketRAID 642L: 79mm x 67mm x 19mm RocketRAID 644L: 106mm x 79mm x 19mm EMI: FCC Part 15 Class B and CE Thermal and Atmospheric Characteristics: Work Temperature Range: +5 C ~ + 55 C Relative Humidity Range: 5% ~ 60% non-condensing Storage Temperature: -20 C ~ +80 C MTBF: 920,585 Hours Electrical Characteristics: PCI-E 3.3V 12V Power 4W max 1W max 5

6 3 Kit Contents RocketRAID 644L HBA / RocketRAID 642L HBA Quick Installation Guide HighPoint Software CD Low-Profile Bracket (RocketRAID 642L only) Two SATA 6Gb/s cables (RocketRAID 642L only) 6

7 4 Hardware Description and Installation 4.1 RocketRAID 644L / 642L Host Adapter Board Layout RocketRAID 642L RocketRAID 644L 4.2 Installing the RocketRAID 644L / 642L Host Adapter Note: Make sure the system is powered-off before installing the RocketRAID host adapter. 1. Open the system chassis and locate an unused PCI-E x16 slot. 2. Remove the PCI-E slot cover. 3. Gently insert the RocketRAID 644L / 642L into the PCI-E slot, and secure the bracket to the system chassis. 7

8 RocketRAID 644L / 642L 4. After installing the adapter, attach the hard disks or backplane enclosure to the host adapter using the appropriate cables. Note: Many server-level chassis include hard-drive hot-swap bays. For these system chassis, cables are attached to the chassis backplane, rather than directly to each individual hard drive. Consult the chassis manual for proper installation procedures. 5. Close and secure the system chassis. 8

9 4.3 Verifying Installation Once the host adapter and hard drives have been installed into the chassis, boot-up the system to verify that the hardware is properly recognized. If the system detects the presence of the adapter, the RocketRAID 644L / 642L will be displayed in the system information PCI Cards window. Note: The RocketRAID 642L was used for this example, but the procedure applies to the RocketRAID 644L model as well (OS X will identify the HBA as pci1103,644 ). 9

10 5 RocketRAID 644L / 642L Driver Installation 5.1 Driver installation Once you have installed the RocketRAID 644L / 642L Card and booted your Mac, follow these instructions to install the drivers and the HighPoint Web RAID Management software: 1. Click the System Information icon. 2. Click PCI Cards. A single PCI entry labeled pci1103,642 will be displayed ( pci1103,644 for the RocketRAID 644L HBA). Driver Installed should be reported as No for this entry. 3. Insert the RocketRAID 600 Series Software CD into your Mac DVD drive and navigate to the Mac Software package folder: \Driver\RR64xL\Driver\Mac. 4. Double-click on the *.dmg file to mount the disc image. 5. Double-click on the installer package labeled to start the installation process. 10

11 6. Follow the onscreen prompts to install the RocketRAID 644L / 642L driver. After the install has completed, you will be prompted to restart your Mac. You will need to restart in order to use the RocketRAID 644L / 642L. 11

12 5.2 Verify Installation of the Software 1. Click the System Information icon. 2. Click PCI Cards. A single PCI entry labeled pci1103,642 will be displayed ( pci1103,644 for the RocketRAID 644L HBA). Driver Installed should now be reported as Yes for this entry. 12

13 6 Install / Uninstall HighPoint Web RAID Management Software The HighPoint Web RAID Management Software (WebGUI) provides RAID configuration and management features. The software can be installed from the HighPoint software CD. 6.1 Installing the Web RAID Management Software Getting Started Uninstall the previous release before installing the latest web GUI software package. 1. The Web RAID Management Software for RocketRAID 644L and 642L HBA s is automatically installed alongside the driver (see chapter 5 RocketRAID 644L / 642L Driver Installation). 2. To run the Web GUI, start your browser and enter the following URL address or click on the shortcut icon on the desktop: Note: The user name RAID and password hpt for the WebGUI management. 6.2 Uninstalling the Web RAID Management Software 1. Go to the Mac Software package folder: \Driver\RR64xL\Driver\Mac. 2. Double-click on the uninstaller icon to start the uninstallation process. 3. If you are not logged in using the root account, the system will ask you to input the user s password: 13

14 4. Enter the user password and press the Enter key. This will complete the uninstall procedure. 14

15 7 HighPoint Web RAID Management Software HighPoint s web-based RAID Management Software (also known simply as the Web GUI ), is used to monitor and configure hard disks and RAID arrays attached to HighPoint RocketRAID host adapters. The software package must be installed on a system with supported HighPoint RocketRAID controllers installed, and the device driver must be loaded to run the service. A web browser with XML support is required on the client side, e.g. Sarfari, Mozilla or Google s Chrome. 7.1 Running the Web RAID Management Software To run the Web GUI, start your browser and enter the following URL address or click on the shortcut icon on the desktop: Use the short cut icon that is created desktop during the web GUI installation to start the web GUI. If you are accessing the RAID Management interface using a remote system, please update localhost to the server s address. If you are unable to connect to the local system, please make sure hptsvr is running on that system. In addition, make sure you are able to access the remote system via a TCP/IP connection, and make sure the firewall (if configured) is not blocking TCP Port

16 Logging into the Web RAID Management interface Enter default User Name and Password User Name: RAID Password: hpt Remote Login Users connected to a local network can remotely access the Web GUI through the IP address the machine is located on. Open a terminal and type in the following command: ifconfig Once the IP address is obtained users can remotely access the machine by typing in the following address: Address:

17 7.2 Web RAID Management Software - Global View Controller(0): Drop-down menu that displays the controller that is currently being managed. Host Adapter Model: Name of the RocketRAID series controller Logical Drive: Total number of Logical Drives created (single disk or RAID arrays) Physical Drive: Total physical drives detected by the RocketRAID controller Total Capacity: Total capacity of all detected HDD s Configured Capacity: Total GB of capacity configured for in Logical devices Free Capacity: Total GB of capacity that is free for use in creating a JBOD or RAID array 17

18 7.3 Web RAID Management Software - Physical Controller Information Model Name: RocketRAID model number BIOS Version: RocketRAID BIOS version Vendor: Vendor Name PCI Bus Number: PCI slot information PCI Device Number: PCI device number PCI Func Number: PCI function number Update EFI from the web GUI. Browse for BIOS image and click the Submit button. 18

19 7.3.1 Physical - Controller 1 Devices Physical Devices Information: These are the devices attached to the controller. Information includes the device model, serial number and capacity Physical - Controller 1 Devices Physical Devices Information Unplug: Powers off the device or RAID array and allow you to remove the device Model: Device model information Revision: Firmware revision Location: Location number of the device on the host adapter Max Free: Maximum free space available for creating a single disk JBOD or RAID array Status: Device status is Legacy or Normal Serial Number: Serial Number of device Capacity: Total capacity of the device Read Ahead: Caching mode to improve Read performance Write Cache: Caching mode to improve Write performance NCQ: Native Command Queuing, I/O commands that are in a queue are re-ordered for better efficiency Identify LED: A blinking cursor to identify the location of a HDD 19

20 7.3.3 Physical - Rescan The item will rescan the controller to detect devices. 20

21 7.4 Web RAID Management Software - Logical Logical Device Information: Displays information about Logical Devices hosted by the RocketRAID HBA. RAID arrays and single-disk JBOD s are Logical Devices. Example: Windows Disk Management Disk (x) Linux - /dev/sd(x) Mac OS X Disk Utility Physical Device Information: The physical disks attached to the HBA. 21

22 7.4.1 Logical - Create Array 1. Array Type Select the RAID level you wish to create. The RocketRAID 644L/642L support RAID 0, 1, 5, 10 and JBOD. 22

23 2. Array Name Enter a name for the RAID array. This is optional the Web GUI will assign a default name if this is not specified. 3. Initialization Method There are four methods to choose from. Keep Old Data: This is the default option when creating a RAID array. A. This option leaves existing data intact. B. This option does not initialize the array disk. You can use this option when creating RAID arrays with new hard disks (initialization is not generally necessary for new drives, as they contain no data). C. In some cases, this option can be used to recover disabled RAID arrays. Quick Init: The RAID array will be immediately accessible. A. This option will delete all content on the disks. B. This option will not perform disk array initialization. When new HDD s are used this option can be ignored since the there is no data on the hard disks. Foreground: The RAID array is not accessible until disk array initialization is completed. A. This option will delete all content on the disks. B. The logical disks will not be reported to the operating system until initialization is complete. This method is faster than Background, and requires far less time to complete. Background: The RAID array is accessible while disk initialization is being performed. A. This option will delete all content on the disks. 23

24 B. This method will slow the initialization process, but allows the array to be utilized immediately. 24

25 4. Cache Policy There are two options available when creating redundant RAID arrays (1, 5, 10). Write Back: Provides higher write performance for redundant RAID arrays. Data is at risk when there is a power failure, system kernel panic and/or the system is not responsive. Write Through: Provides higher data protection when there is a power failure. Data is written directly to disk. 5. Block Size Block sizes are adjustable from 16K through 1024K. The default setting is 64K. 6. Number of RAID 5 member disk This option is related to creating a RAID 50 array. 25

26 7. Select All This option will instruct the Web GUI to select all available drives. 26

27 8. Logical Device Information After the array has been created, it will be displayed under Logical Device Information. The following information is displayed for each array: Name: Default name of the RAID array Type: Type of RAID array Capacity: Total capacity of the RAID array Cache Policy: Redundant RAID array options for performance or protection Block Size: RAID array block size Sector Size: RAID array sector size OS Name: Status: Name of HDD seen in the OS Status of RAID array. Other option include (Normal, Critical, Disable, Rebuilding, Verifying) 9. Maintenance Maintenance provides a selection of general maintenance features and options for the selected array: The arrays current status and RAID level determine which options and features are provided by Maintenance: 1) RAID status is Normal, there will be a Verify button available. 2) RAID status is Critical, there will be a Add button available. 3) After Add Disk then Rebuilding, it displays Stop button. Delete: Delete the selected RAID array Unplug: Power off the RAID array and remove it Rebuild: Add a disk and rebuild a critical RAID array to normal Change Cache Policy: Toggle between Write Through and Write Back. 4) Write Through: Lower Write performance because data is written directly to HDD. Data cannot be lost due to power failure or some other circumstance. 5) Write Back: Higher Write performance but chances of data lose are greater since data still resides in cache. 6) Rename: Rename the RAID array other than the default 27

28 7.4.2 Logical - Spare Pool When creating redundant RAID arrays (1, 5, or 10) a Spare HDD can be configured to automatically help rebuild a degraded redundant RAID. 28

29 7.4.3 Logical - Logical Device Displays logical devices hosted by the RocketRAID 644L/642L HBA Logical - Rescan When hot-plugging a single device or RAID array, the Rescan button prompts the RocketRAID HBA to scan for device changes Logical - Beeper Mute This will temporarily disable the internal speaker on the RocketRAID 644L / 642L HBA. 29

30 7.5 Web RAID Management Software - Setting This tab displays various controller related settings and options: Setting - System Enable auto rebuild: Enable Continue Rebuilding on error: Enable audible alarm: Set Spindown Idle Disk (Minutes): Restrict to localhost access: Set Rebuild Priority: If enabled, any new disk attached to the HBA will be used to rebuild the critical RAID array. Note: The new disk needs to be equal to or larger than the minimum capacity among the remaining disk members of the array. Enabled by default. If disabled, the Web GUI will ignore bad sectors/read failures and allow the rebuild process to continue. Warning: this option should only be enabled in the case of an emergency data inconsistency or data loss may result. Review the Event Log before enabling this option, and check for HDD bad sector events. If bad sectors are found, we recommend first contacting the HDD manufacturer, then technical support, for further advice. When a disk goes off-line the beeper on the HBA will sound. Hard drives can be instructed to spin down when there is no disk activity for a set period of time. You are free to specify the interval from 10 to 240 minutes. This option is used to restrict web GUI access to the local system and not allow remote access. When rebuilding a critical RAID array there are five rebuilding options to choose from. Each rebuild priority will affect the rebuild completion time. 30

31 Lowest Lowest Priority when rebuilding arrays. System resources will be assigned to all other tasks first. Low Low Priority. Most of the system s tasks have priority over the rebuild procedure. Medium Medium Priority is the default option system resources are equally distributed between the rebuild procedure and other system tasks. High High Priority the majority of available system resources will be directed towards the rebuild procedure. Highest Highest Priority the HBA will utilize all available system resources to rebuild the array. Port Number 7402: Password Setting: The listening port number used to log into the web GUI is the default port number. Other port numbers can be used in place of the default as long as they are free. The default password hpt can be changed. Note: If the current password is lost or forgotten, you can uninstall and reinstall the Web RAID Management software to restore the default settings. When changing the password, the maximum number of characters allowed is eight. 31

32 7.5.2 Setting - The RocketRAID HBA can be configured to send Event Log entries to one or more addresses. 32

33 7.6 Web RAID Management Software - Event The Event tab will open the Event View interface. Event View logs all RAID related activity including administrative actions, warnings and hardware failures. Clear: Next: Download: Click Clear to remove all current entries from the Event View log. The Event View log can span several pages. Click Next to view past entries. The Event View log can be saved as a text file for reference. 33

34 7.7 Web RAID Management Software - SHI (Storage Health Inspector) Storage Health Inspector: SHI will inspect each HDD periodically. If any abnormal status is found, it will be recorded in the Event log. SHI can help to identify problems with HDD s and prevent further damage or data loss. If additional proof of errors is needed, the HDD s can be placed onto the onboard SATA port and a 3rd party SMART software utility can be run. HDD Temperature Threshold: SMART: Setup the HDD temperature threshold to prevent HDD overheating. When the HDD goes beyond the threshold an alert will be triggered. SMART attributes for each HDD will be displayed. 34

35 Task List: The Task tab allows you to schedule maintenance sessions for RAID 1, 5 and 10 arrays. Regular maintenance is highly recommended for any redundant RAID array, and is essential for maintaining healthy, reliable storage configurations. The interface allows you to name each task, and specify the frequency, date, hour minute and second for each session. 35

36 7.8 Web RAID Management Software - Recover Recover can help repair RAID arrays that have been assigned the disabled status. This feature helps protect RAID configurations by storing multiple copies of RAID configuration data, which administrators can use to restore a disabled RAID array. Note: There is a separate How-To guide that explains this Recover feature. 7.9 Web RAID Management ICON Definition List The definitions of each ICON used by the RAID Management interface are listed below (the examples use a RAID 5 array for reference). Icon Description The array status is "Normal". The array has stopped Initializing. Current status is Uninitialized. The array is Initializing : Initializing (Foreground) and Initializing (Background). The array is performing a data consistency checking and its current status is Verifying. The array status is "Critical" - a disk is missing from the RAID array. The array status is "Verifying". This indicates that the array is running a data integrity check. The array status is "Rebuilding". This occurs when the data verification fails or when adding a new disk into the "Critical" array. The array status is "Critical". This indicates that current array needs "rebuild". This icon will also show up on a device in a RAID disk member as needing to "rebuild" its data. 36

37 The status of the "Array" or "Device" is "Disabled". The array is "Initializing". There are two types of initialization- Foreground and Background. The array OCE/ORLM operation has stopped. This icon means the RAID array is "Uninitialized". On the RAID array either Foreground or Background initialization has stopped (Incomplete). On a disk ( ), it indicates that the disk is not initialized and will need to be initialized for the 1 st time before it can be used with HighPoint RAID card. The device status "Legacy". An existing file system has been created on the HDD. The device is a "Spare". It is used to replace the failed RAID disk member to rebuild automatically. Information. Warning. Error. The array is inconsistent and it needs to rebuild. The current status is Critical. Array disk member diagram is listed below. It shows a RAID-5 disk member is lost and its current status is Critical. Array disk member diagram is listed below. The array is rebuilding and its current status is Rebuilding. Array disk member diagram is listed below. 37

38 The array is not available. Two scenarios can cause this to happen. First - a lost RAID disk member exceed the minimum required to maintain a RAID level. Second - a disk failed before the initialization or rebuilding process complete. The status is in Disabled. Array disk member diagram is like this: 38

39 8 EFI EFI is the boot function of RocketRAID 644L / 642L HBA. 8.1 EFI Update You can install and update the EFI to RocketRAID 644L / 642L adapter via its Web Management interface. 1. Visit the website to download the latest EFI. 2. Extract the download zip file to a local directory. 3. To run the Web GUI, start your browser and enter the following URL address or click on the shortcut icon on the desktop: 4. Select Physical. Click the Choose File button towards the bottom of the page. 39

40 5. Browse to the location of the EFI BIOS download and select the rr6xxl-efi64.rom. Click the Choose button. Note: xx refers to the HBA model: 42 for the RocketRAID 642L, and 44 for the RocketRAID 644L. 40

41 6. After the EFI BIOS has been updated, the Web GUI will prompt you to reboot OS X. Click OK to restart the system. 8.2 Booting Mac OS X from RocketRAID 644L / 642L Adapter via EFI Currently Mac OS X cannot be directly installed to Legacy disks or arrays hosted by RocketRAID 644L / 642L HBA s. You will need to clone the current system drive to a disk or array attached to the RocketRAID HBA. The following procedure assumes the RocketRAID HBA and Web GUI is already installed. 1. If a legacy disk is not attached to the HBA, configure a single-disk JBOD or RAID array using the Web GUI. 2. Run Disk Utility, and create a new volume on the array: 41

42 3. Clone the OS X system disk to this new volume using a cloning /duplication utility. We recommend Carbon Copy Cloner: 4. Double-click the Carbon Copy Cloner icon to start the utility. Specify the source (current OS X system disk) and the destination (new volume on the array). 42

43 5. Click the Clone button to start the cloning process. 6. Once the cloning process has completed, open OS X s System Preferences window, and select Startup Disk. Designate the new volume as the Startup Disk and click Restart. Alternately, you can shutdown the system and remove the original system disk OS X should automatically boot from the legacy drive/array the next time you power on the system. 7. Mac Os X will now boot from the legacy disk or array. You are free to remove the original system disk if it is no longer required. 43

44 9 Thank You Thank you for purchasing the RocketRAID 644L / 642L esata RAID Host adapter. We appreciate your support, and welcome any questions, comments or product suggestions you may have. 44

45 10 Customer Support If you encounter any problems while utilizing RocketRAID series host adapters, or have any questions about this or any other HighPoint Technologies, Inc. product, feel free to contact our Customer Support Department. HighPoint Technologies, Inc. websites: Web Support: 45