GL2200 MIXING CONSOLE
|
|
- Job Norton
- 6 years ago
- Views:
Transcription
1 GL2200 MIXING CONSOLE SYS-LINK EXPANDER OPTION This option connects a GL2200 console as a channel expander to a second console with just one or two interconnecting cables. Kit GL2200-SL1 = SINGLE Single option to install SYS-LINK to one GL2200 console to allow interconnection to a second console already fitted with SYS-LINK. Interconnecting cables not supplied. For information on using SYS-LINK please refer to APPLICATIONS NOTE AP3623 FITTING INSTRUCTIONS Publication AP3622 ISSUE 1 JAN 99
2 FITTING THE GL2200 SYS-LINK EXPANDER OPTION 1) CHECK THE CONTENTS: GL2200-SL1 KIT RED, VIOLET, YELLOW, BLUE (ALL) BLUE GREEN ORANGE RED SYS-LINK IDC HARNESS SNAP-IN PILLARS fig. 1 Contents: 1x SYS-LINK circuit board assembly with interconnecting harness and mountings already fitted. 1x SYS-LINK Fitting Instructions (AP3622) 1x SYS-LINK Application notes (AP3623) 1x IDC Harness (AL3616) 2x Snap-In Pillar (AB2233) 1x 8K2 Resistor (AC0045) 2) TOOLS REQUIRED: SLIM BODIED SOLDERING IRON WITH SMALL TIP SOLDER 1pt CROSS POINT LONG NOSE PLIERS 5mm NUT DRIVER 2 GL2200 SYS-LINK OPTION ALLEN & HEATH
3 3) PRELIMINARY: To fit the SYS-LINK option it is not necessary to remove any of the circuit board assemblies as access to the SYS-LINK solder pads can be made with the circuit boards in place. 4) REMOVE THE CONSOLE BASE: Before inverting the console to remove the base, remove the two screws next to the end stereo input channel on the console front panel. Then invert the console and remove the base as shown in fig. 9. 5) REPLACE R45 RESISTOR: Referring to fig. 2 and fig. 3; if R45 is a 22K resistor (bands: red, red, orange) then this needs to be replaced by the supplied 8K2 resistor (bands: grey, red, red). However, if R45 is already a 8K2 resistor (bands: grey, red, red) then do not replace. R45 OSC/Noise fig. 2 6) REMOVE THE BLANKING PLATE & POWER SUPPLY BRACKET The SYS-LINK blanking plate is located on the rear panel. Unscrew the retaining screws and remove the blanking plate. The power supply bracket is located under the PSU. Unscrew the two screws (A) and remove the bracket as shown in fig. 3. ALLEN & HEATH GL2200 SYS-LINK OPTION 3
4 7) DISCONNECTING THE HARNESS ASSEMBLIES: Disconnect the MAIN HARNESS (B) plugged into the connectors mounted along the edge of the circuit boards. Disconnect the flexible flat cables (C) plugged into the GROUP circuit boards. A OSC/Noise C B CONSOLE FRONT GL2200 inverted with the base cover removed. fig. 3 8) FITTING THE SYS-LINK IN HARNESS: Remove the two screw fixings from the harness D Type connector. Mount the D Type connector onto the rear panel with the fixings. Mount the other connector onto the straight molex connector on the Osc/Noise as shown in fig. 4. Harness Stereo Input Osc/Noise Group 1 fig. 4 4 GL2200 SYS-LINK OPTION ALLEN & HEATH
5 9) POSITIONING THE SYS-LINK ASSEMBLY: Fit the bracket to the SYS-LINK circuit board assembly with the 2 nylon snap-in pillars (D) as shown in fig. 5. Place the SYS-LINK and bracket assembly on the console as shown ready for soldering the wires. D SYS-LINK Power supply bracket OSC/Noise Stereo Input Group 3 Group 1 GL2200 with power supply bracket fitted to SYS-LINK assembly. fig. 5 10) SOLDERING THE SYS-LINK HARNESS ASSEMBLY: Referring to fig. 6, prepare the solder pads on the circuit boards with new solder to ease the soldering of the SYS-LINK wires. Note, the wires for the Group, Left & Right s are soldered to the trackside of the circuit boards and not the component side. The wires to the OSC/Noise go through the. It is recommended that the wires in the SYS-LINK harness are soldered to each circuit board in the following order: OSC/Noise, GROUP 3, GROUP 1, LEFT and then finally the RIGHT circuit board assembly. ALLEN & HEATH GL2200 SYS-LINK OPTION 5
6 SYS-LINK WIRING HARNESSES P3 BK M2 BLU M4 YEL M3 PK M2 BLU M4 YEL M3 PK P2 GN M1 RED M1 RED P4 OR M3 BLU P6 RED P5 BLU M1 YEL M4 PK M2 RED RIGHT LEFT GROUP 2 GROUP 1 OSC/NOISE GL2200 WIRING PAD LOCATION FOR SYS-LINK M1 GY fig. 6 6 GL2200 SYS-LINK OPTION ALLEN & HEATH
7 11) FITTING THE SYS-LINK OUT ASSEMBLY: When all the SYS-LINK wires have been soldered, remove the 2 screw fixings from the D Type Connector and manoeuvre the SYS-LINK circuit board and power supply bracket assembly into the console chassis as shown in fig. 7. Mount the D Type Connector onto the rear panel with the 2 fixings. SYS-LINK and power supply bracket fitted into GL2200 console. fig. 7 SYS-LINK In position C B OSC/Noise Stereo Input Group 1 Group 3 fig. 8 ALLEN & HEATH GL2200 SYS-LINK OPTION 7
8 12) REFIT THE POWER SUPPLY BRACKET: Carefully stand the console on its rear panel and re-fit the two front panel power supply bracket screws next to the end stereo input channel. Support the console during this process. Place the console on its control surface and fit the two power supply sub chassis screws. 13) REFIT THE HARNESSES: Referring to fig. 8, re-fit the MAIN HARNESS (B) onto the circuit boards. Check the harness is correctly aligned onto the circuit board connectors with pin 1 aligned with the red stripe of the ribbon harness. Reconnect the two flexible flat cables (C) to the GROUP circuit board assembly. Ensure that all harnessing is tidy. 14) REFIT THE BASE: fig. 9 Refit the base. Locate the two screws for the power supply bracket before fitting the other screws. 15) PLUG ON THE INTERCONNECTING CABLES: SYS-LINK connectors are 25way D Type female. Use 25way D Type male to male connector cables. Connect pin one to pin one on all connectors. Connect shield (screen) to 0V. Standard cables are available from electronic suppliers or computer shops. It is advised that the cable is a screened type less than 10 metres. Use professional quality locking connectors. When connecting to equipment other than the GL Series link all unused audio inputs to 0V earth at the SYS-LINK input. 16) TEST THE SYSTEM: Test all SYS-LINK inputs and outputs for correct signal level and quality by probing the D Connector pins or by interconnecting two consoles with SYS-LINK fitted. Test the PFL/AFL system for correct DC buss switching. The SYS-LINK circuit diagram and technical details are included for reference. The SYS-LINK Applications Note AP3623 is included separately with these fitting instructions. Provide this note to the user as applicable. Please refer any queries to your Allen & Heath appointed service agent. 8 GL2200 SYS-LINK OPTION ALLEN & HEATH
FITTING INSTRUCTIONS
& This option connects a GL3000 or GL3300 console as a channel expander to a second console with just one or two interconnecting cables. Kit Part No: GL3000-SL1 Single option to install SYS-LINK to one
More informationALLEN&HEATH WZ14:4:2+
LLEN&HETH MixWizard Series WZ14:4:2+ SYS-LINK EXPNDER OPTION This option connects a MixWizard WZ14:4:2+ as a channel expander to a second &H console already fitted with SYS-LINK with just one or two interconnecting
More informationAC300/AC400 SERIES DYNAMIC BRAKING and ADDITIONAL FORM C RELAY. INSTALLATION INSTRUCTIONS Document Number:
Minarik Variable Speed AC Motor Drives AC300/AC400 SERIES DYNAMIC BRAKING and ADDITIONAL FORM C RELAY INSTALLATION INSTRUCTIONS Document Number: 250-0297 These instructions apply to models rated: 7.5 25
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationInstallation Instructions. Ecast Mojo B75B Motherboard Upgrade Kit Kit #
Installation Instructions Ecast Mojo B75B Motherboard Upgrade Kit Kit #26684501 This kit contains the parts and instruction to install the B75B Motherboard into your Ecast Mojo jukebox. Tools Required
More informationUpgrading a 2U CHP to an i7 Quad Core SBC
Upgrading a 2U CHP to an i7 Quad Core SBC 1. Parts required: i7 SBC Slim line SATA DVD drive Combined SATA data and power cable for slim-line optical drive Serial port ribbon cable - 9way D male to 10
More informationElectronic Balance Ionizer STABLO-AP Service Manual
321-78209 Jan. 2016 Electronic Balance Ionizer STABLO-AP Service Manual Analytical & Measuring Instruments Division This page is intentionally left blank. Table of Contents 1. Precautions for Troubleshooting...
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationALLEN&HEATH WARNING HIGH VOLTAGES. Power Supply Unit (PSU) work should only be carried out by qualified personnel.
ALLEN&HEATH WARNING HIGH VOLTAGES Power Supply Unit (PSU) work should only be carried out by qualified personnel. We recommend that you use an approved Allen & Heath service centre for all power supply
More informationREMOTE HEAD ADAPTER INSTALLATION GUIDE
REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and
More informationTechnovision Inc. CD-ROM Audio Sampler. Repair Manual
Technovision Inc. CD-ROM Audio Sampler Repair Manual Table Of Contents: Page # INITIAL SETUP & TESTING 3 System Components 3 System Set-Up Procedure 3 Self Test Routine 3 REPAIR ACTION PARTS REPLACEMENT
More informationMegatouch FORCE Monitor Chassis Board Replacement
Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationReplacement Keyswitch Assembly
Installation Instructions Replacement Keyswitch Assembly (Catalog No. 2711E-NKSW1) Applicable Terminals Use this replacement keyswitch with PanelView Terminals 2711-KA1, -KC1, -TA1, -TC1, -TA4, -TC4 and
More information2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual
2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation
More informationINSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,
More informationPost Tenebras Lab. Written By: Post Tenebras Lab
Post Tenebras Lab PTL-ino is an Arduino comptaible board, made entirely out of through-hole components. It is a perfect project to learn how to solder and start getting into the world of micro controllers.
More information4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials..
IV PERSONALITY MODULE ASSEMBLY 4.1 Parts and Components............ IV-1 4.2 Assembly Tips............... IV-1 4.3 Assembly Precautions............ IV-1 4.4 Required Tools, Equipment and Materials.. IV-1
More informationEMC 10T "CE" Mechanical Upgrade Procedure
EMC 10T "CE" Mechanical Upgrade Procedure Kit Part Number: 009866-01 This procedure upgrades a non-ce compliant machine to the mechanical requirements of a CE compliant machine. Properly upgraded machines
More informationInstallation Instructions
Installation Instructions Ecast EQ to AMI hardware conversion KIT #26683701 This kit is for use in Ecast EQ jukeboxes. Tools Required #2 Phillips screw driver, #1 Phillips screw driver, Small flat blade
More informationA-100G6 - Basic frame assembly diagram
doepfer System A - 100 Rack system A-100 G A-100G6 - Basic frame assembly diagram Parts: 1 Rail with lip, and with tapped hole strip inserted (with M3 threads). 2 Rail with lip, with three M3 hexagon nuts
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
15 Monitor Removal 1. Turn off and unplug the game. 2. Place something in front of the game to brace the bezel once the strain relief cord is undone, then unlock and open the CPU section. 3. Remove the
More informationPICAXE EXPERIMENTER BOARD (AXE090)
(AXE00) Description: The PICAXE experimenter board allows circuits for any size/revision of PICAXE chip ( / / ) to be quickly tested using a prototyping breadboard. The experimenter board provides power
More informationHigh Power (15W + 15W) Stereo Amplifier
High Power (15W + 15W) Stereo Amplifier Build Instructions Issue 1.0 Build Instructions Before you put any components in the board or pick up the soldering iron, just take a look at the Printed Circuit
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationPanasonic DMP-BD35/BD55
Panasonic DMP-BD35/BD55 Region switching guide With the mod. chip fitted the player will automatically play DVD's from all regions (1-6), but for Blu-ray disc playback the region must be manually selected.
More informationCarefully remove the translite from the backbox and then lower the speaker panel to the position shown in Fig. A to gain access to the backbox.
Installation Instructions for Data East (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display
More informationMAIN PCB (The small one)
THANKS FOR CHOOSING ONE OF OUR KITS! This manual has been written taking into account the common issues that we often find people experience in our workshops. The order in which the components are placed
More informationINSTRUCTION BULLETIN
INSTRUCTION BULLETIN No. 9008755 Machine: T16 Published: 03-2011 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More informationPhase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:
Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss
More informationArrakis Systems 6604 Powell Street / Loveland, Colorado 80538
Arrakis Systems 6604 Powell Street / Loveland, Colorado 80538 Input and Output wiring for the 150sc, 500sc, 2000sc and 2100sc audio consoles. A Input Channel Wiring (Back of Console) 6. Left Input 5. Left
More informationTopic: TB No.: Date: Aug/2017. Model UC4, UC10 & UC45 twin pump variants Regulated 24V Pump Power supply upgrade OVERVIEW
Topic: TB No.: 10041 Date: Aug/2017 Affected Machines: UC4/UC10 &45 variants Priority: Medium Created By: Gareth Fitzpatrick From Serial No.:
More informationBehringerMods.com. Instructions for modification of Behringer SRC analog inputs and outputs
BehringerMods.com Instructions for modification of Behringer SRC analog inputs and outputs The following instructions will cover the details of fully modifying a unit with analog output and analog input
More informationM40e and M160 CIP Installation Instructions
Part No. 530-005365-01 Revision 2 23 January 2002 CIP Description This document describes how to remove and replace the Connector Interface Panel (CIP) on a Juniper Networks M40e Internet router or M160
More informationBreezeMAX Wi² and BreezeACCESS Wi² Quick Installation Guide
This Quick Installation Guide is intended for experienced installers. For more information refer to the relevant sections in the BreezeMAX Wi² and BreezeACCESS Wi² System Manual. Wi² Package Content Check
More informationCarefully remove the translite from the backbox and then swing speaker panel to the open position as shown in Fig. A to gain access to the DMD.
Installation Instructions for SEGA (wooden speaker panel) Congratulations on the purchase of your new display. The will enhance your pinball machine by introducing color to the dot matrix display graphics
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More informationSection. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1
Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.
More informationPico Amiga ATX power adaptor install guide
Pico Amiga ATX power adaptor install guide Introduction The ATX power adaptor allows you to power your Amiga A500/A600/A1200 or CD32 from a modern ATX power supply. This variant of the design has a right
More informationPanasonic DMP-BD60/BD80
Panasonic DMP-BD60/BD80 Region switching guide With the mod. chip fitted the player will automatically play DVD's from all regions (1-6), but for Blu-ray disc playback the region must be manually selected.
More informationUzebox Kit Assembly Guide
Uzebox Kit Assembly Guide V1.3 Page 1 of 18 Revision History Version Date Author Description 1.0 01-Nov-2012 A.Bourque Initial release 1.1 6-Nov-2012 A.Bourque Minor corrections 1.2 28-Jan-2014 A.Bourque
More informationFC-25/50DA Main Circuit Board Replacement Product Installation Document
FC-25/50DA Main Circuit Board Replacement Product Installation Document Document 51875 Rev A 10/12/01 ECN 01-506 This Product Installation Document outlines the replacement of the Main Circuit Board for
More informationInstructions to Install Retrofit Kit 6/7000 Machine
Instructions to Install Retrofit Kit 6/7000 Machine **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit kit contents: PART NAME QUANTITY PART NUMBER
More informationInstructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only)
Instructions to Install Retrofit Kit RVMC 4/5000 Machine (MDB Only) **TURN POWER OFF OF MACHINE BEFORE INSTALLATION** READ ALL INSTRUCTIONS BEFORE STARTING INSTALLATION Retrofit Kit Contents PART NAME
More informationDark Energy Survey Detector Head Electronics Crate Disassembly & Modular Replacement Instructions For Type 2 DAQ & Heater Crates
Dark Energy Survey Detector Head Electronics Crate Disassembly & Modular Replacement Instructions For Type 2 DAQ & Heater Crates University of Illinois at Urbana-Champaign Todd Moore Vaidas Simaitis Allison
More informationNewScope-T0 Operation Manual
2014 SIMMCONN LABS, LLC. All rights reserved NewScope-T0 Operation Manual Including NewScope-T0 and NewScope-T0e February 26, 2017 NewScope-T0 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1
More informationCourtesy of:discountcarstereo.com USB-CDR30. ation Guide for Porsche CDR30/31. Radios Revised: January 10, 2018
Courtesy of:discountcarstereo.com USB-CDR30 Quick Start Installation ation Guide for Porsche CDR30/31 Radios Revised: January 10, 2018 Introduction: Portable audio products are everywhere, reflecting demand
More informationSnap Server 4400 Power Supply
Snap Server 4400 Power Supply Snap Server 4400 Note You can set up your system to send an e-mail alert in the event of a hardware failure. For details, see the section on e-mail notification in your Administrator
More informationReplacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly
Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,
More informationPacific Antenna Two Tone Generator
Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination
More informationPoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.
ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power
More information1. Carefully unpack the um260 s shipping carton and check the contents for damage.
um260 Installation Manual um260 Installation Chapter 4 um260 MICRO MONITOR INSTALLATION This section of the um260 Micro Monitor Installation Manual describes the requirements and procedures for installing
More informationAF Upgrade Instructions
8602 8631AF Upgrade Instructions Bering Technology, Inc. 1400 Dell Avenue, Suite B Campbell CA 95008-6620 (408) 364-6500 FAX: (408) 364-6501 Email: info@bering.com Contents 15-18631-81 Revision D This
More informationVoice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document
Voice Evacuation Control Panel Main Circuit Board Replacement Product Installation Document Document 50795 Rev B 10/10/01 ECN 01-507 This Product Installation Document outlines the replacement of the Main
More informationPhysical Specification Vending Machine Card Reader Module Model: CRM-170-xx
Vending Machine Card Reader Module Model: CRM-170-xx Version C (26/08/05) Contents Section Title Page 1 Component Layout 3 2 Cables 6 2.1 Executive Power 6 2.2 Executive Data - External 6 2.3 Executive
More informationNavigation interface for Jeep GC 5 RA2 NTV-KIT581
3950 NW 120 th Ave, Coral Springs, FL 33065 TEL 561-955-9770 FAX 561-955-9760 NNG-Jeep GC Navigation interface for Jeep GC 5 RA2 NTV-KIT581 NNG-JEEP GC Kit Content 5 1 6 4 7 2 3 1. 2. 3. 4. 5. 6. 7. 8.
More informationInstallation Instructions
Installation Instructions Phones, Navigation These Installation Instructions supersede those dated February 2004. Page 1 of 9 March 2004 Accessory Development Changes to this revision are identified by
More information1. Mount the echo and tremolo control switches under the keyboard shelf, in a position convenient for the organist.
CONSOLE CONNECTOR KIT 8101 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models A-100, D-100, RT2, RT3 LESLIE Speaker Models 122, 122RV KIT CONTENT Console Connector Assembly 047357 Echo Control
More informationANIxx. Installation Manual.
ANIxx Installation Manual www.audac.eu Introduction WaveDynamics Dante audio network interface The ANIxx are Dante audio network interfaces for use with WaveDynamics supporting amplifiers, supporting two
More informationUltimate LPF kit: Relay-switched LPF kit
Ultimate LPF kit: Relay-switched LPF kit PCB Revision 4 1. Introduction Thank you for purchasing the QRP Labs relay-switched low-pass filter (LPF) kit. This kit is designed to complement the Ultimate3
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More information1%$6+2:7,0(*2/'(',7,21 1)/%/,7=*2/'(',7,21 &219(56,21.,7
1%$6+2:7,0(*2/'(',7,21 1)/%/,7=*2/'(',7,21 &219(56,21.,7 C H A P T E R F I V E WIRING WARNING: Failure to reconnect ground wires or replace metal shields may result in radio frequency interference. NOTICE:
More informationVector 3D printer complete wire list including extruder PWA listing
Vector 3D printer complete wire list including extruder PWA listing Conventions Pin numbering for connectors It is normal practice in print circuit board (PCB) layout to denote pin 1 of a PCB mounted connector
More informationREMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.
REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right
More informationNOTE: Read the instructions completely through before beginning actual installation.
CONSOLE CONNECTOR KIT 7850 INSTALLATION INSTRUCTIONS FOR USE WITH: Various Two-channel Organs LESLIE Speaker Models 705, 705C, 720 KIT CONTENT Console Connector 138488 Switch Assembly, Cable Assembly,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. MP3 ATTACHMENT KIT 2006 RIDGELINE AII 28615 Issue Date FEB 2005 PARTS LIST Attachment Kit: P/N 08B06-SJC-100 MP3 Player Kit (sold separately):
More informationPrint Mechanism Maintenance Kit
Print Mechanism Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the print mechanism maintenance kit in the following printers: ZT0 ZT0 ZT0 Read
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationINSTALLATION INSTRUCTIONS
TM REPLACEMENT PARTS FOR USE WITH CX SERIES PANELS INSTALLATION INSTRUCTIONS Hubbell Control Solutions 9601 Dessau Road Building One Suite 100 Austin, TX 78754 Toll Free: 888-698-3242 Fax: 512-450-1215
More informationADDENDUM FOR 20, 27, & 28 OPTIONS
ADDENDUM FOR 20, OPTIONS GENERAL The 20, 27, and 28 option provides for an alarm contact OR an AC transfer switch on EXELTECH XP Series inverters. The alarm relay monitors the inverter s AC output and
More informationCourtesy of:discountcarstereo.com USB-C5. Quick Start Installation Guide for Select Corvette
Courtesy of:discountcarstereo.com USB-C5 Quick Start Installation Guide for Select 1997-04 Corvette Created January 16, 2013 Revised October 24, 2018 Introduction: Just because you drive an older car does
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationAccessories for control enclosures. BERNSTEIN attachment solutions. Double coupling head (console version with suspension system attachment)
25 Accessories for control enclosures BERNSTEIN attachment Single coupling head (suspended console version) Double coupling head (console version with suspension system attachment) 322.5 231 232 140 The
More informationModel ver INSTALLATION MANUAL Rev CHD Elektroservis
Model 8-435 ver. 1.0 INSTALLATION MANUAL Rev. 2 7 2018 CHD Elektroservis Contents page 1 INTRODUCTION.................................................................. 3 1.1 MIDI INTERFACE KIT PARTS.......................................................
More informationInstruction Add a second I/O board
Instruction Add a second I/O board Kit art. No. 472991911 438 9041-81/EN 2013.07.04 Instruction 3 1 Add a second I/O board Contents of the kit Type 2 I/O board P-Bus wire harness D-Bus wire harness Adhesive
More informationSRI-02 Speech Recognition Interface
SRI-02 Speech Recognition Interface Data & Construction Booklet The Speech Recognition Interface SRI-02 allows one to use the SR-07 Speech Recognition Circuit to create speech controlled electrical devices.
More informationAdapter Kit - QSI Electronics to G-Series Meter Installation Instructions
Adapter Kit - QSI Electronics to G-Series Meter Installation Instructions These installation instructions cover the adapter kit installation of the QSI1, QSI2 and QSI3 versions of communications electronics
More informationElecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved
Introduction Elecraft K3 KPA3 Power Connector Replacement Revision B, June 30, 2017 Copyright 2017, Elecraft, Inc. All Rights Reserved The connectors furnishing high current to the KPA3 module have failed
More informationThe GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.
Introduction 1 Welcome to the GENIE microcontroller system! The GENIE Light Kit is ideal for introducing simple lighting projects, such as an electronic die, a wearable badge or a night-time warning system.
More informationSLE SYMPHONY LOUDNESS ENABLER. Installation & Users Manual. for Rover 75 with Symphony Audio System (Alpine OEM) with or without Lo-Line Navigation
SLE SYMPHONY LOUDNESS ENABLER Installation & Users Manual for Rover 75 with Symphony Audio System (Alpine OEM) with or without Lo-Line Navigation Part N o 02088 (intentionally left blank) Important Notice
More informationReplacing the SATA PCI Controller Card
Replacing the internal controller PCI card may be performed by a single administrator; no tools are necessary. Caution There are static-sensitive electronics inside the unit. Before you handle any parts,
More informationVBAR 270. User Manual. Version 1.2
VBAR 270 User Manual Version 1.2 VBAR 270 User Manual Page 1of 19 Introduction Thank you for purchasing VBAR 270. VBAR 270 is a LED light fixture for professional use. Using the RGB color mixing technology
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationRH-8 Headphone Station. Installation Guide
RH-8 Headphone Station Installation Guide 2 RH-8 Installation Guide Contents Safety Information...4 Introduction...4 What s in the Box... 5 Top view... 6 Base view... 7 Installation...8 Connections...
More informationSCXI-1345 Shielded Cable
NATIONAL INSTRUMENTS The Software is the Instrument Installation Guide SCXI-1345 This guide describes how to install the SCXI-1345 shielded cable with an adapter board between an SCXI module and a data
More informationSingle cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
More informationUzebox Kit Assembly Guide
Uzebox Kit Assembly Guide V1.7 Page 1 of 21 Revision History Version Date Author Description 1.0 01-Nov-2012 A.Bourque Initial release 1.1 6-Nov-2012 A.Bourque Minor corrections 1.2 28-Jan-2014 A.Bourque
More informationRSL PSM-2 Power Supply Module Project: Modifying a FlatCap2
RSL PSM-2 Power Supply Module Project: Modifying a FlatCap2 Dear Do-It-Yourselfer, The stock FlatCap2 is less than a stellar performer. Used with a CD5 CD player, for example, it gives flabby bass control,
More informationGV-EL124S Electric Strike
GV-EL124S Electric Strike Featured with a built-in door status sensor, the GV-EL124S is a fail-secure electric strike, but it is field convertible from fail secure to fail safe. It can be mounted either
More informationThe SL2100 Quick Install Guide: Terminals Type A (4w)
The SL2100 Quick Install Guide: Terminals Type A (4w) www.nec-enterprise.com SL2100 Digital Terminals Type A (4w) This guide explains the installation, configuration and operation of the SL2100 Type B
More informationIntel NUC Kit NUC8i7HNK & NUC8i7HVK User Guide. Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide
Intel NUC Kit NUC8i7HNK Intel NUC Kit NUC8i7HVK User Guide 1 Before You Begin CAUTIONS The procedures in this user guide assume familiarity with the general terminology associated with personal computers
More informationPARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 10kΩ Resistor OTHER PARTS YOU MAY NEED
PARTS LIST 1 x PC Board 36 x 5mm Red LED 36 x 12mm LED Standoff 36 x NPN Transistor 36 x 150Ω Resistor 36 x 10kΩ Resistor 17 x Mini Toggle on-off 8 x Mini Toggle (on)-off-(on) 1 x 470Ω Resistor 1 x 47µF
More informationWritten By: Charlie Mohr
NEC LCD1770NX Capacitor Replacement Replacement of a capacitor on the power supply circuit board. Written By: Charlie Mohr ifixit CC BY-NC-SA www.ifixit.com Page 1 of 14 INTRODUCTION There are many capacitors
More informationInstalling Keypad and Backplate
Installing Keypad and Backplate Fig.1 Positioning of Fixing Holes and Cable Outlet Cable Outlet, Drill Diameter 10mm for Cable Access Remove the back plate, which is fitted to rear of the keypad, using
More informationE2460GS Oscilloscope Upgrade Kit
Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent
More informationController PC Hard Drive
Controller PC Hard Drive Remove and Replace Procedure Guide (Models RL/FT5000 XP ) TDN 07103-00194 08/2008 Corporate Headquarters: 522 E. Railroad Street Long Beach, MS 39560 Phone: (228) 868-1317 Fax:
More informationInstallation instructions DC Protection and Delay unit, Version 1.2 The package should contain: A piece of normal gauge yellow wire for the AC connect
Installation instructions DC Protection and Delay unit, Version 1.2 How does the unit work? Delay: Basically a capacitor is charged via a resistor, when the voltage of the capacitor reach a certain level,
More informationWEASEL N/B MAINTENANCE
2. System Assembly & Disassembly 2.1 System View 2.1.1 Front View ❶ Microphone Connector ❷ Audio Input Connector ❸ Audio Output Connector ❹ Top Cover Latch ❹ ❶ ❸ ❷ 2.1.2 Left-Side View ❶ VGA Port ❷ S-Video
More information