INSTALLATION INSTRUCTIONS

Transcription

1 GM MyLink Dual Video Input Interface for Factory Display Radios (Kit # v2) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: v2 module AV Input harness GVIF video cable RGB input cable Power/CAN harness Remote IR eye harness Input toggle switch These instructions Tools & Supplies Needed: Wire cutters Wire strippers Zip ties Electrical tape Heat shrink Torx T20 7mm socket Plastic panel removal tools! Safety Precautions: Work in well ventilated area that is clear of obstructions. Secure vehicle with tire chucks in both front and rear of tires. Turn vehicle accessories OFF and ensure ignition key is in OFF position. Wear safety goggles and snug fitting clothes. Use tools only for their intended purpose and which are in good repair. Only perform this task if confidence, skill, and physical ability permit. NOTE: We strive to provide accurate and up-to-date installation instructions. For the latest full color instructions, as well as an installation video, please visit v2 Instructions docx Page 1! of! 5

2 INTERFACE CONNECTORS: DIP SWITCH SETTIN: Configure PRIOR to installation v2 Instructions docx Page 2! of! 5

3 INSTALLATION: 1. Remove the factory radio. This usually requires pulling panels and removing a series of screws. Disconnect any associated harnesses and set the radio aside. 2. Gather the provided Power/CAN Harness from the v2 kit. Connect the following wires to the car: BLACK to chassis ground, RED (ACC) to accessory, and GRAY (REAR) to reverse lamp 12V (pin 2, pink BCM) 3. Connect the factory GVIF cable from the factory radio. This is a square, blue connector. 4. Connect the male side (labeled LXIN ) of the provided GVIF video cable to the factory radio. 5. Connect the free end (removed in step 3) of the factory GVIF video cable to the female side of the provided GVIF video cable (labeled LXOUT ). 6. Connect the white end of the GVIF video cable to the interface at the port labeled LVDS IN/OUT. 7. Connect the AV Input cable to the port on the v2 interface labeled AV IN/OUT. If you re only connecting a reverse camera (and no other inputs), the signal input from the camera must connect to the RCA labeled REAR-C. Refer to the DIP switch settings chart to skip/enable AV sources upon toggle switch presses (optional. Page 2). 8. Adjust DIP switches on the v2 interface properly, refer to the chart on page 2 for qualifications. 9. Connect the white plug from the Power/CAN Harness to the port on the v2 interface labeled Power/CAN. 10. Optional: Connect the remote eye to the port labeled IR (on the power harness) and leave it in clear view of the driver (often it can be stuck inside a vent). This connection would be necessary if you want to be able to adjust anything from the v2 interface s menu. Refer to Menu Adjustments for menu options. 11. Optional: Connect the provided momentary toggle switch to the port on the v2 interface labeled MODE. Pressing this switch with the ignition on will cycle the screen modes as follows: factory screen > NAVI (RGB) > AV1 > AV2 > AV3 > factory screen. Please refer to the DIP switch section on page 2 for input settings. 12. Start the car and test for proper functionality before replacing dash pieces. Note: All other included harnesses not mentioned in these instructions are not needed for most installations v2 Instructions docx Page 3! of! 5

4 ! INSTALLATION INSTRUCTIONS MENU ADJUSTMENTS: v2 Instructions docx Page 4! of! 5

5 FAQ: Q: I cannot switch A/V sources. A: Check IR or toggle switch connec4on. Check the LEDs on the interface, if nothing is lit up with vehicle igni4on, check power/ground connec4ons. Q: All I see on the display is a black screen (no factory image pass-through). A: Make sure the video cables (IN/OUT) are connected at the proper loca4on (Screen/Radio/NAV DRIVE). Make sure the video cables are seated all the way. Make sure DIP switches 5 & 6 are set correctly (resolu4on or screen size). Q: Displayed image color is not proper (too dim or color seems wrong). A: Try to select INITIAL in OSD menu. Q: Rear camera image does NOT appear. A: Make certain DIP switch #7 in set down for avermarket camera, or up for a factory camera. Try swapping the CAN connec4on wires. This will not do damage, if it is hooked up wrong it will only not work. Make certain the camera is properly powered. Check voltage at the camera itself. Try an alterna4ve video source, don t assume the power/ground is correct unless you ve checked it with a mul4-meter! If this is a CAN-connected module and you ve connected the CAN wires, try using the gray wire (not all interfaces have this wire!) instead of the CAN connec4on for reverse ac4va4on. You ll also need to change the Rear Select op4on in the Menu of Factory (MENU 2) under UTIL or PARK. Refer to the Menu Adjustments sec4on. Q: Unwanted A/V mode is displayed upon a toggle press (A/V source switching order: OEM->RGB->AV1- >AV2->AV3->OEM). A: Check DIP Switch SeYng. Refer to page 2. POWERED BY: v2 Instructions docx Page 5! of! 5