Installation. Setting Up Expression 303

Transcription

1 Installation This section describes how to set up the Expression cabinet and make any necessary adjustments to the interior shelves. In addition, this section tells you how to connect: an internal computer, keyboard and mouse a projector a printer a VC a DVD player Setting Up Expression emove the cabinet from its shipping carton. 2. Wheel the cabinet to an appropriate location within reach of a power source. NOTE: eave sufficient space around the entire cabinet so you can comfortably access it as you perform the following assembly and connection procedures. 3. ock the casters by pushing down on the caster tabs; unlock the casters by pulling up on the caster tabs, as shown in the figures below. NOTE: As a safety precaution, and for greater ease of use, the casters should remain locked while Expression 303 is in use. Push Tab Down to ock Caster Pull Tab Up to Unlock Caster Expression 303 Installation and User s Guide 9

2 Unlocking the Doors Expression 303 ships with all three doors locked. A single key will unlock all doors. You ll find this key in the key holder (at the rear of the cabinet, to the left of the Connection Panel). The locations of the key holder and of the three door locks are shown below. Key Holder ocation of Key Holder Front View Side View ear View ocation of Door ocks 10 Expression 303 Installation and User s Guide

3 Adjusting the Shelves Expression 303 comes equipped with two laminated shelves to accommodate your peripherals. To accommodate non-standard sized equipment, you may need to move one of these shelves up or down. The shelves are vertically adjustable in 1¼" increments. emove the shelf by applying pressure to the top tab of the plastic shelf pegs and then maneuvering the shelf up and out. Finally, pull out the four plastic pegs and reposition them. Push in to remove shelf Pull out to remove peg Shelf support Push into shelf hole Plastic Shelf Pegs Pushing Shelf Pegs into Place Expression 303 Installation and User s Guide 11

4 Connecting an Internal Computer 1. Open the computer compartment (side) door, and position your computer next to the open door. 2. ocate the bundle of cables inside the computer compartment and pull it out. Computer Cables NOTE: The cable numbers below correspond to the numbered cables in the figure on the opposite page. 3. Connect the DB15 HD video cable (#4) to the monitor video connector. 4. Connect the 3.5 mm stereo audio cable (#3) to the Audio ine Out socket. 5. Connect the DB9 connector (#6) at the end of the serial cable to the COM (serial) port. 6. Connect the PC printer cable (#8) to the 25-pin parallel port. 7. Connect the J45 network cable (#1) to the network card. 8. Connect the IEC power outlet cord (#5) to the computer power inlet. Turn to page 14 for instructions on connecting the keyboard and mouse to the computer. 12 Expression 303 Installation and User s Guide

5 1 J45 Network Connector 2 USB Connector mm Stereo Connector 4 HD DB15 Video Connector 5 IEC Power Outlet 6 DB9 Serial Connector 7 DB9 Serial Connector 8 DB25 Printer Connector Computer Cable Connectors 1 J45 Network Connector Connect to J45 network card on rear of computer. Provides access to the resources of the connected network. 2 USB Connector Connect to your computer s USB port or USB hub mm Stereo Audio Connector Connect to the Audio ine Out socket. Directs computer audio to Expression 303 audio internal mixer, amplifier and speakers. 4 HD DB15 Video Connector Connect to the monitor video connector. Directs computer video to the projector via the X-Port 10 switch. 5 IEC Power Outlet Connect to the computer power inlet. 6/7 DB9 Serial Connectors Connect to an available serial port on the rear of your computer. 8 DB25 Printer Connector Connect to the parallel port. Connects the computer to the integrated printer. Expression 303 Installation and User s Guide 13

6 Connecting a Keyboard and Mouse 1. Place the keyboard and mouse on top of Expression 303, close to the cable opening. 2. emove the cable opening cover and drop the keyboard and mouse cables down the exposed opening. eplace the cover without pinching the cables. Mouse/Keyboard Cable Opening PS/2 Mouse and Keyboard Connectors 3. From the inside of the cabinet, pull the two PS/2 connectors down and through to the rear of the uninstalled computer. 4. Insert the keyboard and mouse PS/2 connectors into the appropriate PS/2 ports on the rear of the computer. Now that the computer is fully connected, carefully slide it inside the computer compartment, with the front of the computer facing the side door. 14 Expression 303 Installation and User's Guide

7 Connecting a Projector To make connection easier, put the projector on top of Expression Connect a standard CA video cable (not provided) from the projector Video Input to the CA Video (Composite) Output in the Connection Panel (for the projector-to-vc connection). If you're using an s-video cable (not provided), connect it from the projector S-Video Output to the S-Video Input in the Connection Panel 2. Connect a DB15 video cable (not provided) from the projector Video Output to the DB15 Video Input in the Connection Panel. 3. Connect a standard S232 serial cable (not provided) from the projector DB9 serial data port to the DB9 serial output in the Connection Panel (enabling on-screen projector controls for a connected SMAT Board). 4. If desired, use the mesh cable sheath located in the Accessory Bag to combine all these cables into one easy-to-manage cord. 2 To GB Input 1 To Video Input USB AUDIO OUT GB VIDEO OUT S232 S-VIDEO OUT SMAT BOAD 12V PINTE SOUCE 1 IN VIDEO IN SOUCE 2 IN 3 To Serial Data Port S-VIDEO IN 1 To S-Video Input APTOP COMPUTE Connection Panel Expression 303 Installation and User s Guide 15

8 5. Plug the projector power cord into a power adapter cord (located in the Power Kit), and then into one of the power outlets adjacent to the Connection Panel. Power Outlet 6. If you re not using the projector immediately, slide it into its storage shelf. Depending on the size of your projector, you may need to slide it onto the shelf in a sideways position. Otherwise, leave the projector on top of Expression during operation. Projector on Storage Shelf 16 Expression 303 Installation and User's Guide

9 Connecting a Printer 1. Place the printer on the middle shelf in the peripheral cavity, with the back of the printer towards you. Printer 2. Connect one end of the DB25 printer cable (not provided) to the parallel port on the rear of the printer, and the other end to the Printer Port on the Connection Panel. To Printer DB25 Parallel Port USB AUDIO OUT GB VIDEO OUT S232 S-VIDEO OUT SMAT BOAD 12V PINTE SOUCE 1 IN VIDEO IN SOUCE 2 IN S-VIDEO IN APTOP COMPUTE Connection Panel Expression 303 Installation and User s Guide 17

10 3. Plug the printer power cord into a power adapter cord (located in the Power Kit), and then into one of the power outlets adjacent to the Connection Panel. Power Outlet 4. Open the front door to access the printer during operation. 18 Expression 303 Installation and User's Guide

11 Connecting a VC or DVD Player 1. Place the VC or DVD player directly on the bottom of the peripheral cavity, with the back of the VC/DVD player towards you. VC/DVD Player NOTE: For steps 2 (a and b) and 3 (a and b) below, refer to the figure on the next page. 2a. If you re using a composite CA video cable (not provided), connect one end to the Video Out jack on the VC or DVD. This jack may be labeled To Monitor. Plug the other end of this cable into the Video Input in the Source 1 Input section of the Connection Panel. 2b. Connect standard red and white CA audio cables (not provided) from the CA / Audio Outputs on the VC/DVD to the two CA / Audio Inputs in the Source 1 Input section of the Connection Panel. Be careful to keep your right and left channel connections correct for stereo sound. 3a. If you're using an s-video cable, connect it to the "S-Video out" connector on the VC/DVD. Plug the other end directly into the S-Video Input in the Source 2 Input section of the Connection Panel. 3b. Connect standard red and white CA audio cables (not provided) from the CA / Audio Outputs on the VC/DVD to the two CA / Audio Inputs in the Source 2 Input section of the Connection Panel. Be careful to keep your right and left channel connections correct for stereo sound. Expression 303 Installation and User s Guide 19

12 USB 2a To Video Input AUDIO OUT GB VIDEO OUT S232 S-VIDEO OUT SMAT BOAD 12V 2b To VC/DVD Audio Output PINTE SOUCE 1 IN VIDEO IN SOUCE 2 IN S-VIDEO IN COMPUTE Connection Panel 3b To VC/DVD Audio Output 3a To S-Video Input 4. Plug the VC/DVD power cord into a power adapter cord (located in the Power Kit), and then into one of the power outlets adjacent to the Connection Panel. Power Outlet 5. Open the front door to access the VC/DVD player during operation. 20 Expression 303 Installation and User's Guide