Control Box Setup - PRSalpha

Size: px
Start display at page:

Download "Control Box Setup - PRSalpha"

Transcription

1 ShopBotTools.com Control Box Setup - PRSalpha Copyright 2016 ShopBot Tools, Inc. page 1

2 Copyright 2016 ShopBot Tools, Inc. page 2

3 Parts List: Hooking Up a PRSalpha Gantry Tool Powering the PRSalpha Control Box The power to the PRSalpha control box should be wired into a fused disconnect by a licensed electrician familiar with industrial equipment. The Power Requirements for the PRSalpha control box and Router/Spindle vary according to configuration. The table below outlines some of the power requirements for different configurations. A schematic for the power requirements for specific configurations can be found in the door of the PRSalpha control box. The power requirements for a Porter Cable router and for a spindle are different, so different components are installed in the PRSalpha control box depending on which will be used. This is not user configurable. Configurations were specified at the time these components were ordered. US Standard, 60Hz PRSalpha Control Box and Porter Cable Router: 220V single phase, 20A circuit. The two legs will be split into two 110 circuits inside the PRSalpha control box: one for the PRSalpha control box, and one for the router. PRSalpha Control Box and Spindle (3 phase): 110V 15A circuit for the PRSalpha control box plus 230V 3-phase circuit for the spindle. Specifications for full-load current of the different models of spindle are provided with the spindle. PRSalpha Control Box and Spindle (single phase): 110V 15A circuit for the PRSalpha control box plus 220V single phase circuit for the spindle. Specifications for full-load current of the different models of spindle are provided with the spindle. Copyright 2016 ShopBot Tools, Inc. page 3

4 PRSalpha Control Box and two Porter Cable routers: 220V single phase, 20A circuit. The two legs will be split into two 110 circuits inside the PRSalpha control box: one for the PRSalpha control box, and one for the two routers. PRSalpha Control Box and two Spindles: 110V 15A circuit for the PRSalpha control box plus the appropriate 220V or 230V circuit for the spindles. European Standard, 50Hz PRSalpha Control Box and 230V/50Hz Porter Cable Router (single speed): 230V single phase line with 10A circuit for the PRSalpha control box plus 15A/230V single phase line for the Porter Cable Router. PRSalpha Control Box and Spindle (3-phase) 230 V single phase circuit (10A) for the PRSalpha control box plus 380V 3-phase circuit for the Spindle. Specifications for full-load current of the different models of spindle are provided with the spindle. Mount the PRSalpha Control Box Mount the PRSalpha control box to the front side of the machine, on the right of the left most leg on ShopBot models with cutting lengths ; for ShopBot models with cutting lengths 144 or greater, mount the control box on the right side of the second leg from the left. Installation Install four T-nut ball & spring pivot inserts (000728) on the inside face of the table side in lowest slot. Copyright 2016 ShopBot Tools, Inc. page 4

5 Loosely attach two upper control box brackets to T-nuts in the table side slot with 3/4 button head screws and flat washers. Note that their orientation may need to be flipped to keep from interfering with the existing cross supports. Mount the lower control box bracket to the lower left tab of the control box with two flat washers, 1 button head screw, and Nyloc nut. Space the upper control box brackets at the approximate distance of the tabs on the control box. Lift the control box into place and mount using two flat washers, 1 button head screw, and Nyloc nut for each bracket. Slide the control box toward the left most leg on the machine and attach the lower control box bracket to the leg. Mount the lower control box bracket to the side of the leg with bolt, two flat washers, two lock washers and nut. Once the lower bracket is firmly in place tighten the button head screws fastening the upper brackets to the table sides. Copyright 2016 ShopBot Tools, Inc. page 5

6 Explore PRSalpha Control Box WARNING: Disconnect electrical power to the Control Box. Failure to do so can cause personal and/or equipment damage. Open the side of the box with a screwdriver (quarter turn). Note that the door cannot be opened or closed unless the switch is turned off. The control box has an interlock for the router/spindle. This interlock allows for the power to the router/spindle to be disconnected without interrupting power to the machine. The switch must be engaged for the router/spindle to run. This provides additional safety for manual tool changes during a cutting file. The contactors, located at the top of control box, are the large relays that control power to the equipment. They are controlled by the E-Stop and by software. The size of the contactor may vary with the power requirements of the device it is powering. Additional contactors for additional devices (example, second router or spindle) are added to the left of the standard contactors. The Fuses in the control box (US 60Hz power) are dependent upon the setup: Porter Cable router (single): 1@ 30A fuse, 1@ 15A fuse Porter Cable routers (two): 1@ 30A fuse, 2@ 15A fuses Spindle: 1@ 30A fuse, no other fuses (spindles are protected by fused disconnect before the control box.) Troubleshooting: Although the fused disconnect should protect the control box, check the fuses and replace if necessary if power is lost to everything in the control box. Copyright 2016 ShopBot Tools, Inc. page 6

7 Inside the PRSalpha Control Box This is a general setup. Actual box may not be the same as illustrated depending on model. 1. Disconnect switch 2. Grounding strip 3. Fuses 4. 24v Power Supply 5. 12v Power Supply 6. Contactors 7. Motor drivers 8. Roxtec Fixture 9. Inputs/Outputs 10. To E-stop switch 11. To 3-Button Pendant Copyright 2016 ShopBot Tools, Inc. page 7

8 Open the Roxtec Fixture The Roxtec Wire Management Fixture attached to the side of the PRSstandard control box gives all wires a tight entry and will seal the PRSstandard control box against dust and debris. Below is the manufacturer s suggested installation. Copyright 2016 ShopBot Tools, Inc. page 8

9 For disassembly, reverse the order of the above steps. For optimum reliability, wait 24 hours or longer after installation before exposing the cables to strain or pressure. Try to route cables perpendicularly through the frame. Once all of the cables inside the PRSstandard control box are attached, run the cables through the modules and tighten the fixture to keep dust out of the PRSstandard control box. It may be necessary to run more than one of the smaller cables in the same gasket. Do not tighten the Roxtec module completely until all cables and wires are routed through the control box. Connect the VFD and Spindle Run power from the ShopBot Control Box to the VFD. Power to the VFD must be connected to the proper contactor in the ShopBot Control Box. This is necessary for the safety systems to work correctly if the Emergency Stop button is pressed. The Yaskawa VFDs supplied by ShopBot has a power cable pre-installed at the factory. WARNING: Disconnect electrical power to the Control Box. Failure to do so can cause personal and/or equipment damage. Run the black cable from the VFD to the vacant cord grip in the bottom of the Control Box. Insert the cable from the VFD into the cord grip, pushing enough wire into the control box to reach the spindle contactor(s) and the ground bus bar. Connect to contactor #2 for a single spindle (#1) and contactor #6 for a second spindle (#2). Refer to the Control Component Placement Diagram ( ) included in the door of the ShopBot Control Box to locate the contactors. Connect the Green wire from the VFD power cable to the ground bus bar, located under the main disconnect in the Control Box (#2 in the Inside the Control Box photo above above). Connect the line conductors from the VFD to the proper contactor using the following terminals: 3 Phase Spindles Single Phase Spindles 2T1 - Black Wire 2T1 - Black Wire 4T2 - White Wire 6T3 - White Wire 6T3 - Red Wire Ground - Green Wire Ground - Green Wire Tighten cord grip. Copyright 2016 ShopBot Tools, Inc. page 9

10 Connect Brown VFD Cable to Control Box The brown cable may have one of two possible wire combinations: Three wires - black, white, and red (red clipped back) Three wires - black, green, and red (red clipped back) The white and green are interchangeable. Run the brown cable from the VFD to the Control Box. Pass the brown cable from the VFD through the cable access in the right side of the Control Box. Connect the black wire and the white (or green) wire from the brown cable into the VFD terminals on the Control Board labeled VFD1 (For a second spindle, use the terminals labeled VFD2 ). Connect the black wire to the FWD terminal and the white (or green) wire to the DCM terminal. The red wire is not used and should be clipped back. Attach Fan Connection Plug to HSD Spindle Attach the fan connection plug (36ft cable) to the front face of the HSD spindle. Tighten fan connection plug screw. Attach Fan to 24V Power Supply The PRSalpha comes with a 24v power supply already installed in the Control Box. Strip back ~ 1/4 of insulation from both the red and black wires at the loose end of the cable from the fan connection plug. Route cable inside the control box and connect the red wire to the (+) and the black wire to the (-) on the top of power supply. Copyright 2016 ShopBot Tools, Inc. page 10

11 Connect Power Cable from VFD to Spindle. Plug electrical connector into HSD spindle power plug and depress the metal clip until it snaps in place. Re-connect and turn on the Control Box. The fan should power up and start turning when the control box is turned on. Plug Motor Cables into Drivers Run motor cables through Roxtec opening and plug them into to the drivers (black boxes arrayed horizontally in the control box - #7 in the open PRSalpha control box illustration shown earlier). The white plug fits the white receptacle on the driver in only one way. Make sure it is aligned correctly and fully seated. From the entry point of the cables: X1 (one red tape) and X2 (two red tapes) go to the two drivers at the far right. Those two drivers move simultaneously on Channel 1 (they), and can be plugged into either driver. The Y motor cable (blue tape) is plugged into Channel 2 - the 3rd driver from the right. The Z motor cable is plugged into Channel 3 - the 4th driver from the right. Additional motors (Accessory Z, etc.) would be plugged into the additional drivers to the left of the four standard drivers. Emergency Stop Switch and 3-Button Pendant The 3-Button Pendant and E-Stop are bundled together for shipping. Both must be attached in order for the E-Stop and the 3-Button Pendant to function. The 3-Button Pendant allows the reset, start and extra emergency stop buttons to be located at a convenient location. It has been prewired so that hooking it up entails plugging the terminal block from the pendant into the control board (control box may differ slightly from pictures depending on tool model. The separate E-Stop Switch is fitted with a terminal block that plugs into the control board. Power for the router or spindle is routed through the control box safety controls so that activating the E-stop by hitting the RED BUTTON will stop the movement of the carriages and power down the router or spindle. Note: Without the E-Stop connected, Input #4 will flash red on the computer screen and the ShopBot Control Software will not allow the ShopBot to move. Copyright 2016 ShopBot Tools, Inc. page 11

12 Proximity Switch and Z Zero Plate Run proximity switch and Z-zero plate cables through the Roxtec opening into the control box. Install black wire of X-axis Proximity Switch cable into Input 2 on the blue terminal block on the control board. Install black wire of Y-axis proximity switch cable into Input 3 on the same blue terminal block. Install the blue wires from both switches in Gnd (ground). Install brown wires from both the switches in the +24V position on the blue output terminal block. Note that the terminal blocks can be removed to make wire insertion easier. When the control box is powered up, a red LED in the body of the proximity switch will stay bright until it is triggered by coming near a target. The black wire for the Z zero plate goes in the Input#1 terminal and the white (or green) wire goes into a ground terminal (Gnd). The red wire goes to 5+ (it is only used by the digitizing probe). Connect the USB cable into the right side of the Control Board. Plug the longer 10ft cable supplied by ShopBot into this connector, and run the longer cable through the Roxtec fixture. Do not plug in the USB cable to your computer at this point. Seal Roxtec Cable Entry Copyright 2016 ShopBot Tools, Inc. page 12

Upgrading to a RBK Control Box

Upgrading to a RBK Control Box Page 1 Upgrading to a RBK Control Box ShopBot Tools, Inc. Technical Support 3333-B Industrial Drive, support @shopbottools.com Durham NC 27704 1-888-680-4466 ShopBotTools.com Page 2 Revision History Date:

More information

Installing 6 Indexer: PRS Standard Tools

Installing 6 Indexer: PRS Standard Tools 888-680-4466 ShopBotTools.com Installing 6 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Overview...5 Installing the

More information

Instructions for Installing the ShopBot 3- Button Pendant Retrofit for PRT/PRSalphas

Instructions for Installing the ShopBot 3- Button Pendant Retrofit for PRT/PRSalphas Installing the 3-Button Pendant Retrofit Page -1- Instructions for Installing the ShopBot 3- Button Pendant Retrofit for PRT/PRSalphas The 3-Button Pendant can be added to PRS/PRT alpha ShopBots and can

More information

3 Indexer Installation For PRSalpha Tools

3 Indexer Installation For PRSalpha Tools 888-680-4466 ShopBotTools.com 3 Indexer Installation For PRSalpha Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents General Safety and Precautions...5

More information

Nov. 07, 2013 p. 5 - changed the B axis unit value to from Changed by Randy per Frank s request.

Nov. 07, 2013 p. 5 - changed the B axis unit value to from Changed by Randy per Frank s request. Correction notes Nov. 07, 2013 p. 5 - changed the B axis unit value to 45.1389 from 40.0000. Changed by Randy per Frank s request. Jan. 22, 2018 p. 5 - changed the B axis unit value and corresponding picture

More information

E1135C PDU and Pod Upgrade Procedure

E1135C PDU and Pod Upgrade Procedure E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support

More information

Keypad Lock. Operation and Service Manual. Order parts online

Keypad Lock. Operation and Service Manual. Order parts online Keypad Lock Order parts online www.follettice.com Operation and Service Manual 801 Church Lane Easton, PA 18040, USA Toll free (800) 523-9361 (610) 252-7301 Fax (610) 250-0696 www.follettice.com 00163345R00

More information

2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual

2015 SIMMCONN LABS, LLC. All rights reserved. NewScope-T1 Operation Manual 2015 SIMMCONN LABS, LLC. All rights reserved NewScope-T1 Operation Manual April 12, 2017 NewScope-T1 Operation Manual 1 Introduction... 3 2 Installation... 4 2.1 Initial Inspection... 4 2.2 Installation

More information

Installing a Power over Ethernet injector

Installing a Power over Ethernet injector Installing a Power over Ethernet injector AlphaEclipse StreetSmart and RoadStar signs The instructions in this document explain how to install/replace a Power over Ethernet (PoE) injector in a StreetSmart

More information

Ag Leader Technology. DirectCommand Installation Hardi 20-pin Interface Kit (Sprayer Chassis Mount)

Ag Leader Technology. DirectCommand Installation Hardi 20-pin Interface Kit (Sprayer Chassis Mount) Part Name / Description Part Number Quantity DirectCommand Hardi Sprayer Kit 4100882 1 Dust Receptacle 8-pin 2002975-8C 1 Installation Instructions 2006335 1 Quick Reference Card- Liquid Application 2002831-38

More information

Welch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement

Welch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement Welch Allyn Connex Vital Signs Monitor 6000 Power Supply Replacement Replace the power supply in a 6000 series Welch Allyn Connex Vital Signs Monitor. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com

More information

Megatouch FORCE Monitor Chassis Board Replacement

Megatouch FORCE Monitor Chassis Board Replacement Megatouch FORCE Monitor Chassis Board Replacement Visit the Merit Industries, Inc. Web site http://www.meritind.com merit industries, inc. PM0337-01 Rev C Table of Contents FORCE Classic Monitor Chassis

More information

Assembly and Setup Manual

Assembly and Setup Manual M-11 Series Copyboard/C-11 Series Captureboard Assembly and Setup Manual This is the installation and assembly manual for the M-11 series/c-11 series. To the Customer Specialized techniques are required

More information

Raven Adapter Harness

Raven Adapter Harness Note: Indented items indicate parts included in an assembly listed above Quantity by System Part Name/Description Part Number With Switch Box With Built-in Switches Raven Harness Adapter Kit 4100504 1

More information

Installing and Removing SDRAM and DRAM

Installing and Removing SDRAM and DRAM CHAPTER 4 This chapter explains how to remove and replace the main memory modules on the network processing engine or network services engine. For the location of the memory module you are replacing, find

More information

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100800 1 Cable Installation Kit 2000901-1 1 Dielectric Grease 2002872

More information

Optional Accessories 6 2

Optional Accessories 6 2 Accessories Chapter 6 Table of Contents Optional Accessories 6 2 Finger Guards 6 2 Remote Touchscreen 6 3 RJ45 to RJ12 Adapter 6 5 Serial Modbus Communication Splitter 6 5 Communication Modules 6 7 Replacement/Spare

More information

PRODUCT MANUAL Duet DMX & Wireless RGB-W Controller

PRODUCT MANUAL Duet DMX & Wireless RGB-W Controller Product Description Solid Apollo LED s new wall mounted Duet DMX & RGB-W LED Controller has been created to control LED light fixtures in three different ways. Users can independently control DMX enabled

More information

GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000

GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000 GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000 Instruction Manual D2-3390-2 The information in this manual is subject to change without notice. Throughout this manual, the

More information

A note about our online installation instructions:

A note about our online installation instructions: A note about our online installation instructions: Most Modern Fan Co. products have been in our assortment for several years or longer. As we continually work to improve product performance and user experience,

More information

Removal and Installation8

Removal and Installation8 8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever

More information

Q2 XBee Handheld Controller Assembly Guide

Q2 XBee Handheld Controller Assembly Guide Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:

More information

Star Trac Fitness E-ST 5090 Stepper. Install Guide

Star Trac Fitness E-ST 5090 Stepper. Install Guide Star Trac Fitness E-ST 5090 Stepper Install Guide STAR TRAC E-ST STEPPER Install Guide E-ST 5090 E Series Stepper ASSEMBLY AND SETUP The following parts are included with the base STAR TRAC E-ST STEPPER:

More information

Electrical Management System (EMS) EMS-HW30C & EMS-HW50C

Electrical Management System (EMS) EMS-HW30C & EMS-HW50C Electrical Management System (EMS) EMS-HW30C & EMS-HW50C Installation & Operating Guide for: Model EMS-HW30C Rated at 120V/30A and Model EMS-HW50C Rated at 240V/50A Surgio Says Lifetime Warranty on all

More information

A-100G6 - Basic frame assembly diagram

A-100G6 - Basic frame assembly diagram doepfer System A - 100 Rack system A-100 G A-100G6 - Basic frame assembly diagram Parts: 1 Rail with lip, and with tapped hole strip inserted (with M3 threads). 2 Rail with lip, with three M3 hexagon nuts

More information

Installation Instruction VCPRGBGM05 - rev1.5 RGB Interface Harness modification Navigation Radio

Installation Instruction VCPRGBGM05 - rev1.5 RGB Interface Harness modification Navigation Radio Introduction The following instruction procedure is for the RGB interface to a GM 05 Nav Radio as part of the Webasto Product NAVCam Back-up Camera (VCP-0000220). In addition, an installer will need to

More information

Instruction Manual. Electrical Management System (EMS) EMS-HW30C & EMS-HW50C

Instruction Manual. Electrical Management System (EMS) EMS-HW30C & EMS-HW50C Instruction Manual Electrical Management System (EMS) EMS-HW30C & EMS-HW50C EMS-HW50C EMS-HW30C! CAUTION These instructions are intended to provide assistance with the installation of this product, and

More information

Installation Guide. Retrofit Kit for USB Ready Intraoral Systems

Installation Guide. Retrofit Kit for USB Ready Intraoral Systems Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the

More information

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt

RAM Rail Mount Kit RAM 201U 5 Arm RAM 2461U Monitor Mount RAM 235U Base, Double U-Bolt DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity DirectCommand Kit 4100852 1 Cable Installation

More information

A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE

A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE C ONTENTS Choose an Installation Guide...... Before You Begin.............. 3 Disconnect the Light Cable........ 3 Cut the Light Cable............

More information

Replacing the Power Supply

Replacing the Power Supply APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools

More information

Ag Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series

Ag Leader Technology Insight. Direct Command Installation Spra-Coupe 7000 Series Note: Indented items indicate parts included in an assembly listed above. Part Name / Description Part Number Quantity Direct Command Spra-Coupe 7000 Kit 4100531 1 Liquid Product Control Module 4000394

More information

CONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Receptacle Kit and a Protective Cover Assembly.

CONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Receptacle Kit and a Protective Cover Assembly. Revised Sept-28-2009 Sealed Industrial Ethernet Circular IP67 Cat. 5e RJ45 Connector System Instructions CONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Kit

More information

GEN 6 LOCKPICK INSTALLATION OPTIONS COPYRIGHT 2010 COASTAL ELECTRONIC TECHNOLOGIES, INC.

GEN 6 LOCKPICK INSTALLATION OPTIONS COPYRIGHT 2010 COASTAL ELECTRONIC TECHNOLOGIES, INC. AFTERMARKET FRONT/BABY CAMERA VIDEO CONNECT HERE FRONT/BABY CAM POWER TO LOCKPICK RED W/BLACK STRIPE WIRE TO LOCKPICK BLACK GROUND WIRE UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE PLUG AND PLAY

More information

REMOTE HEAD ADAPTER INSTALLATION GUIDE

REMOTE HEAD ADAPTER INSTALLATION GUIDE REMOTE HEAD ADAPTER INSTALLATION GUIDE The Remote Head adapter is a valuable accessory for the Uniden BC-780, 785 and 796 scanners. It allows the scanner's control panel to be removed from the radio and

More information

ETC Installation Guide

ETC Installation Guide ETC Installation Guide Desire Series D22 Introduction ETC s Desire D22 is designed for indoor installations and has a rugged die-cast enclosure, steel mounting yoke, and noise-free, fan-less operation.

More information

641G-001A PRINTER KIT INSTRUCTIONS

641G-001A PRINTER KIT INSTRUCTIONS 641G-001A PRINTER KIT INSTRUCTIONS P-11351 5/05/98 SAFETY The installer of this equipment must assume the responsibility for his own safety, and that of those working around him. He must also make sure

More information

FDS / FDS-R / FDS-PS

FDS / FDS-R / FDS-PS FDS / FDS-R / FDS-PS USER MANUAL For use with 120V 60Hz input. Output is 120V 60Hz at 5amps 600W MAX. switched. ETL LISTED Conforms to UL STD 1241 3091594 79-15167-00 REV. A www.fiberstars.com Page 1 of

More information

Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443

Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443 Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY. PARTS LIST: 2 Metal Plate Stands 5 Greenery

More information

3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs)

3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs) 3M Add-On Terminals 4220P (100, 200, 300 & 400 pairs) Instructions August 2011 3 78-8130-2330-1-C 1.0 General 1.1 The 3M Add-On Terminals 4220P-100, 4220P-200, 4220P-300 and 4220P-400 are designed to expand

More information

TDM To MiniMech conversion ProceDure

TDM To MiniMech conversion ProceDure TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Flat Screen Garage End User & IT Computer Cable Management May 2013 nylon zip-tie #2 (for computer wires) rear-access beam door (open) Figure 1 nylon zip-tie #1 (for #1 motor control

More information

Part Name/Description Part Number Quantity

Part Name/Description Part Number Quantity Part Name/Description Part Number Quantity Direct Command 4200159 1 Cable Installation Kit 2000901-1 1 Hood 37-pin DSub 2001808-37 2 Dielectric Grease 2002872 1 Dust Plug 12 Pin Gray 2002899-12N 1 Feature

More information

ADDITIONAL CAM POWER REVERSE CAM POWER BLUETOOTH MUTE AUDIO + IN AUDIO - IN 12V ACC OUTPUT 12V CONSTANT GROUND

ADDITIONAL CAM POWER REVERSE CAM POWER BLUETOOTH MUTE AUDIO + IN AUDIO - IN 12V ACC OUTPUT 12V CONSTANT GROUND UNPLUG ORIGINAL RADIO CONNECTORS THEN PLUG IN HERE PLUG AND PLAY NO OTHER CONNECTIONS ARE NECESSARY USE HANDSFREE KIT MICROPHONE IPOD/IPHONE/ITOUCH/IPAD CONNECTION USB INPUT ADD YOUR BLUETOOTH HANDSFREE

More information

G12/G12x USER S MANUAL

G12/G12x USER S MANUAL G12/G12x USER S MANUAL TABLE OF CONTENTS SECTION 1 SLIDE CONFIGURATION SECTION 2 SLIDE CONFIGURATION ACCESSORIES SECTION 3 TABLETOP CONFIGURATION SECTION 4 TABLETOP CONFIGURATION ACCESSORIES SECTION 5

More information

imac Intel 21.5" EMC 2389 Stand Replacement

imac Intel 21.5 EMC 2389 Stand Replacement imac Intel 21.5" EMC 2389 Stand Replacement Replace a broken or cosmetically unappealing stand on the imac 2389 21.5 Written By: Aaron Cooke ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION

More information

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator.

Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Nanodyne Replacement Illuminator for Zeiss xioskop Microscope Microscope with original illuminator. Microscope with Nanodyne replacement illuminator. Copyright 09 Nanodyne Measurement Systems. Document

More information

Olympus Stylus 1030 SW Camera Lens Replacement

Olympus Stylus 1030 SW Camera Lens Replacement Olympus Stylus 1030 SW Camera Lens Replacement Written By: Shanmei Zheng ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 TOOLS: Phillips #00 Screwdriver (1) ifixit Opening Tools (1) Spudger (1) T6 Torx

More information

* C29* 68P81084C29-0 RETROFIT INSTRUCTIONS FOR MCS 2000 MOBILE RADIOS. Conversion From Dash/Local Mounting To Remote Mounting

* C29* 68P81084C29-0 RETROFIT INSTRUCTIONS FOR MCS 2000 MOBILE RADIOS. Conversion From Dash/Local Mounting To Remote Mounting Conversion From Dash/Local Mounting To Remote Mounting RETROFIT INSTRUCTIONS FOR MCS 2000 MOBILE RADIOS Kit Number H634( ) for Model I Radio Kit Number H635( ) for Model II and Model III Radios Introduction

More information

TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION

TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION S6 USER S MANUAL TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION SECTION 4 SLIDE CONFIGURATION ACCESSORIES SECTION 5 RACK MOUNT

More information

V5420 Host Card Upgrade Kit for R3082D Quick Start Guide

V5420 Host Card Upgrade Kit for R3082D Quick Start Guide Quick Start Guide Upgrade kit contents The table below shows the contents of the V5420 Host Card Upgrade Kit (components are not shown to scale). Part Function Pieces V5420 Host Card 1 Host card bracket

More information

Installing Power Modules

Installing Power Modules This chapter contains the procedures for installing cards and modules into the chassis after the chassis has been installed into a rack. This chapter also describes how to connect cables to RSP, RP, alarm,

More information

Power Supply and Fan Module Installation

Power Supply and Fan Module Installation 3 CHAPTER This chapter describes how to remove and install a new or replacement power supply or fan module in a Catalyst 3750-E or Catalyst 3560-E switch. See these sections: Installation Overview, page

More information

Cab Box Kit Dome Plug Cab Box Cab Box Lid

Cab Box Kit Dome Plug Cab Box Cab Box Lid DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100578 1 Cable Installation

More information

GM NBS Truck CCD Backup Camera Kit Installation Guide

GM NBS Truck CCD Backup Camera Kit Installation Guide CS GM1 GM NBS Truck 2007 2012 CCD Backup Camera Kit Installation Guide Thank you for your purchase! These instructions are intended for the do it yourselfer who decides to install the camera without professional

More information

CHAPTER 3B: ELECTRONIC POWER STEERING

CHAPTER 3B: ELECTRONIC POWER STEERING Electronic Power Steering CHAPTER 3B: ELECTRONIC POWER STEERING NOTE: The basic steering system, such as the tie rod ends, drag links axles, etc., is covered in Chapter 3A: Steering. In 2012, Cub Cadet

More information

Part Name/Description Part Number Quantity

Part Name/Description Part Number Quantity Part Name/Description Part Number Quantity Direct Command Kit 4100883 1 Installation Instructions 2006336 1 Hardware Kit Large Module 2001354-1 2 Cable Installation Kit 2000901-1 1 Quick Reference Card

More information

xtablet T1600 Vehicle Holder Installation Guide

xtablet T1600 Vehicle Holder Installation Guide This document will step you through setting up the T1600 Vehicle Holder installation and tips for a safe, clean and long lasting installation. Preparing to Mount the Vehicle Holder Warning : Dock mounting

More information

6 Removal and replacement

6 Removal and replacement 6 Removal and replacement This chapter contains information about the following topics: Removal and replacement strategy User-replaceable parts Covers and external components Main assemblies Motors and

More information

Mounting on the Ceiling Using Flush Mount (Face Down)

Mounting on the Ceiling Using Flush Mount (Face Down) Mounting on the Ceiling Using Flush Mount (Face Down) Installation Guide 2014/02/14 Table of Contents Safety Information... 3 Installation Procedures... 5 Step 1: Drill a Hole on the Ceiling... 5 Step

More information

A Axis M-Functions Level 1 A Axis Standard A Axis SMT Level 2. Each console includes the following:

A Axis M-Functions Level 1 A Axis Standard A Axis SMT Level 2. Each console includes the following: Hardware List The 3000M Crusader II Upgrade system has been custom configured to provide the necessary hardware required for installation on your machine. Verify that you have received all the correct

More information

Installation/Operating Instructions 220V VCB Silhouette/Series E Electric Video Conferencing Background by Draper

Installation/Operating Instructions 220V VCB Silhouette/Series E Electric Video Conferencing Background by Draper Installation/Operating Instructions 220V VCB Silhouette/Series E Electric Video Conferencing Background by Draper Caution 1 Read instructions through completely before proceeding; keep them for future

More information

Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2

Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 1 Installation Guide for Mazak Mazatrol M - Plus, M-2, M32, T-Plus, T2 Tsubis Part Number: LCD12-0046 Power Down 1. Power down the controller. 2. Power down the complete machine by turning off the rear

More information

Section. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1

Section. Service & Maintenance. - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Section G Service & Maintenance - Core & Hard Disk Drive (HDD) - Amplifier - Monitor - UPS - Dollar Bill Acceptor - Fan Filter G - 1 Core Removal Core & HDD 1. Open the door. 2. Perform shutdown procedure.

More information

E3 CNC Router Troubleshooting Guide

E3 CNC Router Troubleshooting Guide Simple Cost Effective Designs. E3 CNC Router Troubleshooting Guide The purpose of this document is to give those new to CNC routing is a quick reference for the common issues of getting the E3 CNC router

More information

4888 and 4988 Outdoor Protected Entrance Terminals

4888 and 4988 Outdoor Protected Entrance Terminals 4888 and 4988 Outdoor Protected Entrance Terminals Underwriters Laboratories (UL) Listed Instructions January 1997 34-7031-7272-5 Revision C Contents: 1.0 General... 1 2.0 Accessories... 2 3.0 Protector

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS CONSOLE CONNECTOR KIT 7830 FOR USE WITH: LESLIE Speaker Model 130 Various single and double channel organs INSTALLATION INSTRUCTIONS KIT CONTENT Console Connector 137283 Switch Assembly, Cable Assembly,

More information

DirectCommand Installation 5 Channel Spreader Control Module Technology

DirectCommand Installation 5 Channel Spreader Control Module Technology DirectCommand Installation Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100582 1 Cable Installation

More information

JLTX Lever and Joystick Replacement Instructions

JLTX Lever and Joystick Replacement Instructions JLTX Lever and Joystick Replacement Instructions WARNING THE INCORRECT INSTALLATION OF A LEVER OR JOYSTICK CAN CAUSE AN EQUIPMENT MALFUNCTION FAILURE TO FOLLOW THIS PROCEDURE CAREFULLY COULD RESULT IN

More information

H3C S12500 Routing Switch Series

H3C S12500 Routing Switch Series H3C S12500 Routing Switch Series Quick Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: APW201-20131030 Copyright 2013, Hangzhou H3C Technologies Co., Ltd. and

More information

HOW TO REPLACE A PARKER INVERTER DRIVE WITH A YASKAWA V1000 INVERTER DRIVE

HOW TO REPLACE A PARKER INVERTER DRIVE WITH A YASKAWA V1000 INVERTER DRIVE HOW TO REPLACE A PARKER INVERTER DRIVE WITH A YASKAWA V1000 INVERTER DRIVE Important: Please read this document in its entirety before removing the Parker VFD drive and installing the Yaskawa V1000 drive.

More information

- ELV OVERVIEW. InstallationGuide SUPPLIED PARTS RELATED PARTS. Brackets Fixtures. Other. 1 of 9 IG-STR9-ELV

- ELV OVERVIEW. InstallationGuide SUPPLIED PARTS RELATED PARTS. Brackets Fixtures. Other. 1 of 9 IG-STR9-ELV OVERVIEW The STR9 ELV is a long run, low power, linear surface mount LED lighting system designed for exterior architectural lighting applications. This guide contains important information on planning

More information

Installation Instructions

Installation Instructions Please read all instructions before installing RS-350 PIR Dual Relay Universal Application Wall Switch Vacancy Sensor with Manual ON/OFF Lens Lighted Switch ON/OFF button for Relay 1 ON/OFF button for

More information

E2460GS Oscilloscope Upgrade Kit

E2460GS Oscilloscope Upgrade Kit Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent

More information

DirectCommand Installation DirectCommand Complete Wiring Harness

DirectCommand Installation DirectCommand Complete Wiring Harness Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number With Switch Box Quantity by Model With Boom Switch Cable Display Cable Kit 4100814 1 1 Power Control

More information

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly

CAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the

More information

OnePlus 5 Screen and Digitizer Assembly Replacement

OnePlus 5 Screen and Digitizer Assembly Replacement OnePlus 5 Screen and Digitizer Assembly Replacement Follow this guide to replace the screen and digitizer for the OnePlus 5. This replaces the screen as well as the frame it is attached to. Written By:

More information

Gateway Profile 4 service guide

Gateway Profile 4 service guide Gateway Profile 4 service guide Customizing Troubleshooting Contents Replacing Components in Your Gateway Profile 4.................. 1 About this guide.....................................................

More information

R1 Extender. Quick Installation Guide

R1 Extender. Quick Installation Guide R1 Extender Quick Installation Guide V1.0 January 2009 Copyright Copyright 2008 all rights reserved. No part of this publication may be reproduced, adapted, stored in a retrieval system, translated into

More information

Indoor Protected Entrance Terminal 4588 Series

Indoor Protected Entrance Terminal 4588 Series Indoor Protected Entrance Terminal 4588 Series Instructions Underwriters Laboratories (UL) Listed September 2003 78-8135-1209-8-A 1.0 General The 3M Indoor Protected Entrance Terminal (PET) 4588 Series

More information

Modular Table Power System Installation for Runner Non-folding Plug and Play Tables

Modular Table Power System Installation for Runner Non-folding Plug and Play Tables Modular Table Power System Installation for Runner Non-folding Plug and Play Tables Topic General Safety Warnings Ganging Hardware Electrical Circuits Table of Contents Page End-to-End (Page 4) End-and-Back

More information

AutoMax Network Communication Option Board for use with GV3000/SE AC Drives M/N 2AX3000

AutoMax Network Communication Option Board for use with GV3000/SE AC Drives M/N 2AX3000 AutoMax Network Communication Option Board for use with GV3000/SE AC Drives M/N 2AX3000 Instruction Manual D2-3308-7 The information in this manual is subject to change without notice. Throughout this

More information

DirectCommand Installation CASE IH SPX Ag Leader Technology. PN: Rev. E January 2014 Page 1 of 19

DirectCommand Installation CASE IH SPX Ag Leader Technology. PN: Rev. E January 2014 Page 1 of 19 Note: These installation instructions only cover installation on SPX 4420 Sprayers only. For installation on SPX 3230/3330 Sprayers refer to Installation Instructions P/N 2005945. For SPX 4430 refer to

More information

Plasma Panel Replacement Guide DU-42PX12X

Plasma Panel Replacement Guide DU-42PX12X Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be

More information

Written By: senordingdong

Written By: senordingdong Installation of the UniMac V4 adapter into the Apple imac Intel 17". This enables the usage of non OEM LCD panels, and offers an otherwise unavailable Full HD upgrade. This used for repair of the common

More information

Floppy Disk To USB. Converter Installation and. Operation Manual

Floppy Disk To USB. Converter Installation and. Operation Manual Floppy Disk To USB Converter Installation and Operation Manual Kit Price $125.00 Plus Shipping Why Should I Change My Floppy Drive To A USB Drive? You won't ever need floppies anymore and yet you'll be

More information

DirectCommand Installation RoGator Model Year Ag Leader Technology

DirectCommand Installation RoGator Model Year Ag Leader Technology Note: Indented items indicate parts included in an assembly listed above Part Name/Description Part Number Quantity Direct Command Kit 4100801 1 Dual Lock 2000052-9 1 Dual Lock 2000053-9 1 Quick Reference

More information

EPX2155. Piston Pump. Owner s Manual. Model Numbers: Stand Upright Cart Low Boy Cart

EPX2155. Piston Pump. Owner s Manual. Model Numbers: Stand Upright Cart Low Boy Cart EPX Piston Pump Owner s Manual Model Numbers: 000 Stand 00 Upright Cart 00 Low Boy Cart SprayTECH 0 Fernbrook Lane Minneapolis, MN Technical Assistance: -00-- Order Entry: -00--00 Fax: -00--0 www.spraytechinc.com

More information

Vertiv Local Rack Access 18.5" LED LCD Console

Vertiv Local Rack Access 18.5 LED LCD Console Vertiv Local Rack Access 18.5" LED LCD Console With Integrated Keyboard, Touchpad and Dual USB 2.0 Ports Installer/User Guide Technical Support Site If you encounter any installation or operational issues

More information

1. Carefully unpack the um260 s shipping carton and check the contents for damage.

1. Carefully unpack the um260 s shipping carton and check the contents for damage. um260 Installation Manual um260 Installation Chapter 4 um260 MICRO MONITOR INSTALLATION This section of the um260 Micro Monitor Installation Manual describes the requirements and procedures for installing

More information

Ultraloq UL3 Series Fingerprint and Touchscreen Smart Lock

Ultraloq UL3 Series Fingerprint and Touchscreen Smart Lock Ultraloq UL3 Series Fingerprint and Touchscreen Smart Lock Installation Instructions ( V1.4 ) Welcome Installation Video Please watch our easy step by step installation video before attempting to install

More information

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly Replacing the LCD Cable To remove and replace the LCD Cable you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Socket wrench with 10mm socket Removing the Side Panel 1.

More information

Blue Box BLUE BOX TM LTD PARTS REPLACEMENT GUIDE

Blue Box BLUE BOX TM LTD PARTS REPLACEMENT GUIDE Blue Box BLUE BOX TM LTD PARTS REPLACEMENT GUIDE WARNINGS 1. All servicing should be performed by qualified service personnel. 2. WARNING, Battery may explode if mistreated. Do not recharge, disassemble

More information

Written By: Ben Eisenman

Written By: Ben Eisenman iphone 3GS Rear Panel Replacement Replace a broken rear case on your iphone 3GS. Written By: Ben Eisenman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 22 INTRODUCTION The plastic rear half of the iphone.

More information

LED. Sign Module. Assembly Manual

LED. Sign Module. Assembly Manual LED Sign Module Assembly Manual 6/14/2002 3:10 PM 6 2 3 3 E. S a w g ra s s R d S a ra s o ta, F L. 3 4 2 4 0 (9 4 1 )3 7 7-5 7 7 5 F A X(9 4 1 )3 7 8-4 2 2 6 www.acscontrol.com Table of Contents Table

More information

E3 CNC Router Troubleshooting Guide

E3 CNC Router Troubleshooting Guide Simple Cost Effective Designs. E3 CNC Router Troubleshooting Guide The purpose of this document is to give those new to CNC routing is a quick reference for the common issues of getting the E3 CNC router

More information

Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout

Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Installation Instructions Adapter Kit for PanelView 1200/1200e Touch Screen Terminal Cutout Catalog Numbers 2711-NR5T, 2711P-RAT12E2 Topic Page About This Publication 1 Important User Information 2 About

More information

Instruction Manual. M Pump Motor Controller. For file reference, please record the following data:

Instruction Manual. M Pump Motor Controller. For file reference, please record the following data: Instruction Manual M Pump Motor Controller For file reference, please record the following data: Model No: Serial No: Installation Date: Installation Location: When ordering replacement parts for your

More information

PracticeWire Installation Manual

PracticeWire Installation Manual PracticeWire Installation Manual Version 5.0 August 28 th, 2013 PCM Help Desk 1-877-233-9114 Page 1 Table of Contents System Overview 3 Tool List 4 Installation Guide Site Notification 5 Install Universal

More information

Packard Bell. EasyNote BU Series. Disassembly Guide

Packard Bell. EasyNote BU Series. Disassembly Guide Packard Bell EasyNote BU Series Disassembly Guide Table of Contents Overview...3 Technician Notes...3 Disassembly Instructions...3 Reassembly Instructions...3 Required Tools...3 Battery...4 Memory...4

More information