LS-500 SERIES. Digital Laser Sensor Amplifier-separated. Industry s smallest* Industry s smallest* + Stainless steel (SUS) enclosure

Transcription

1 0 PHOTO PHOTO MEASURE separated Digital Laser Sensor -separated SERIES Related Information General terms and conditions... F- SC-GU... P.97~ About laser beam... P.59~ Industry s smallest* panasonic.net/id/pidsx/global Industry s smallest* + Stainless steel (SUS) enclosure Stainless steel (SUS) body Featuring stainless steel (SUS) enclosure that won t break when bumped during installation or maintenance. One-point M6 installation The LS-H0 features an easy-to-install design. M6 Actual size 0 mm.8 in Body: Stainless steel (SUS) Operation indicator (receiver only) * -separated type laser sensor head as of September 0, in-company survey guide... P.69~ Glossary of terms / General precautions... P.59~ / P.55~ diagnosis Self-diagnosis Light intensity monitor This product is classified as a Class Laser Product in IEC / JIS standards and in FDA* regulations. Do not look at the laser beam through optical system such as a lens. Interference prevention PNP output type available Automatic sensitivity setting * -separated type laser sensor head as of September 0, in-company survey sensing range (In STD amplifier response time mode) ø ø Beam-emitting part ø. ø0.09 Test input ø.5 ø , Conforming to FDA regulations * This product complies with CFR 00.0 and 00. Laser Notice No. 50, dated June, 007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration). ø5 ø Unit: mm in Timer LS-H0 Industry s smallest* + IP67 Waterproof IP67 Featuring waterproof IP67 to allow use in the presence of large amounts of water or dust. Simple positioning Check the optimal receiving location at a glance while watching the red spot on the beam axis adjustment screen. * -separated type laser sensor head as of September 0, in-company survey LS-H0 Two-point installation The thru-beam type LS-H0 features the same form as the EX-L00 amplifier built-in ultra-compact laser sensor. And it can be used as an EX-L00 with a digital indicator. Installation pitch mm 0.5 in sensing range (In STD amplifier response time mode) The LS-H0 delivers sufficient sensing range for use with 50 mm 7.77 in wafers. LS-H0 EX-L / EX-L Same installation pitch as the EX-L00 series

2 Digital Laser Sensor SERIES APPLICATIONS 0 Lead frame position detection Wafer inclination detection IC float detection PHOTO PHOTO Detection of workpieces through a workbench Detection of gaskets in caps Detection of the top of DVDs, substrate, etc. MEASURE Gasket * -separated type laser sensor head as of September 0, in-company survey Industry s smallest* + Thinnest profile Featuring a 60% smaller design (by volume) than previous coaxial reflective models Our smallest unit is smaller in every dimension at just W8 H D8 mm W0.5 H0.906 D0.709 in (excluding indicators). LS-H0 8mm in mm in 8mm 0.5 in Coaxial design By using a laser with high linearity in a coaxial design, the LS-H0 is able to deliver stable sensing in confined spaces as well as simple installation. Reflective surface Emitting element Reflective photoelectric sensor Laser light Sensing object Reflected light Emitting part Receiving part Coaxial design Receiving lens Receiving element Coaxial principle Receiving part Small, long-range spot Easy-to-see operation indicator The LS-H0 produces a spot with a diameter of mm in at a sensing range of up to 00 mm.8 in (in STD amplifier response time mode). The LS-H0 s operation indicator is visible from all directions. 00 mm.8 in ø mm ø0.079 in separated

3 0 Digital Laser Sensor SERIES Industry s smallest* + Horizontal symmetry * -separated type laser sensor head as of September 0, in-company survey LS-H90 PHOTO PHOTO MEASURE Horizontal symmetry Featuring a simple system design process thanks to a light source that is placed in the center of the sensor head and a coaxial design. Industry s smallest* and thinnest design The LS-H90 is even thinner than previous models, measuring just W8 H (excluding indicators) D8 mm W0.5 H0.906 D0.709 in. 8 mm 0.5 in mm 0.57 in * -separated type laser sensor head as of September 0, in-company survey Among industry s fastest response times* 60 μs Maximum compatibility with fiber sensors The series features the same operation, menu displays, and form factor as the FX-500 series for increased compatibility with fiber sensors. FX-500 series fiber sensor series laser sensor Detection of beam axis misalignment Dual outputs (self-diagnosis output) The series can detect any reduction in incident light intensity, for example due to the accumulation of dirt such as dust, and issue an alarm. Sensing output can be set as self-diagnosis output. When you teach the threshold for sensing output, sensing output is set accordingly, allowing you to shift the threshold by a previously set margin. Sensing range of 0 mm to m 0.9 in to.8 ft (In STD amplifier response time mode) The LS-H90 supports close-range sensing 0 mm 0.9 in * -separated type laser sensor head as of September 0, in-company survey LS-50 Stable sensing over the long term The s threshold-tracking function helps maintain stable sensing over the long term and reduce maintenance man-hours. The incident light intensity can be checked and the threshold automatically reset at a user-selected interval to track changes in light intensity due to environmental changes (such as dust, etc.) over extended periods of time. Logic operations The s ability to perform three logic operations (AND, OR, and XOR) on a standalone basis eliminates the need for a dedicated controller, cuts down on wiring, and lowers costs. This functionality can also be combined with the FX-500 series. Data bank Eight sets of amplifier settings can be stored in the unit s built-in memory. The ability to save and load settings reduces workload when changing the setup in a multimodel production environment. separated Network communication possible Current values of connected sensors are shown. LS-50 Can connect to Open Network CC-Link IE Field / CC-Link / DeviceNet / EtherCAT via Communication Unit for Open Network SC-GU series. Monitoring and various settings can be done from, PC, etc. しきい値 現在値 ch ch 50 0 ch 0 70 ch 0 0 5ch 0 0 6ch 0 0 7ch 0 0 8ch 0 0 しきい値 現在値 9ch 0 0 0ch 0 0 ch 0 0 ch 0 0 ch 0 0 ch 0 0 5ch 0 0 6ch 0 0 End unit [Touch panel display example] Threshold values of connected sensors are shown. Communication Unit for Open Network SC-GU series Digital laser sensor Digital fiber sensor Digital fiber sensor Digital pressure sensor LS-0/50 FX-50/50 FX-0/05 DPS-0/0 *CC-Link and CC-Link IE Field are a registered trademark of Mitsubishi Electric Corporation. DeviceNet is a registered trademark of ODVA (Open DeviceNet Vender Association, Inc.). EtherCAT is a registered trademark of Beckhoff Automation GmbH. * Refer to p.97~ for details of SC-GU series.

4 Digital Laser Sensor SERIES 0 ORDER GUIDE Sensor heads Thru-beam type Type Cylindrical Square Coaxial reflective type Coaxial retroreflective type Appearance LS-H0 LS-H0 LS-H0 LS-H90 Sensing range : HYPR : U-LG : LONG : STD : ST : H-SP 750 mm 9.58 in 600 mm.6 in 50 mm 7.77 in 00 mm.8 in 00 mm 7.87 in 50 mm in 0.0 to.5 m 0.0 to 8.0 ft 0.0 to m 0.0 to 6.56 ft 0.0 to.5m 0.0 to.9 ft 0.0 to m 0.0 to.8 ft 0.0 to m 0.0 to.8 ft 0.0 to m 0.0 to.8 ft 5 m 6.0 ft cable length type 5 m 6.0 ft cable length types (Standard: m 6.56 ft) are available. When ordering this type, suffix -C5 to the model No. LS-H0-C5 LS-H0-C5 LS-H0-C5 LS-H90-C5 Package without reflector The LS-H90 is also available without a reflector (RF-0). When ordering this type, suffix -Y to the model No. LS-H90-Y s Type Appearance Output Connection method Connector type Cable type With external input Quick-connection cables LS-50 LS-50P LS-50-C LS-50P-C NPN open-collector transistor two outputs PNP open-collector transistor two outputs NPN open-collector transistor two outputs PNP open-collector transistor two outputs Use quick-connection cable (optional) m 6.56 ft cabtyre cable (6-core) included Cable outer diameter: ø mm ø0.57 in Quick-connection cable is not supplied with the connector type amplifier. Please order it separately. Type Appearance Description separated Main cable (-core) CN-7-C CN-7-C Length: Length: m 6.56 ft 0. mm -core cabtyre cable, with connector on one end Cable outer diameter: ø. mm ø0.0 in CN-7-C5 Length: 5 m 6.0 ft Sub cable (-core) CN-7-C CN-7-C CN-7-C5 Length: Length: m 6.56 ft Length: 5 m 6.0 ft 0. mm -core cabtyre cable, with connector on one end Cable outer diameter: ø. mm ø0.0 in Connectable to a main cable up to 5 cables Connector Type Appearance Description Connector for amplifier CN-EP Connector included with sensor head Use for maintenance, for example when another connector is damaged. Five pcs. per set

5 05 Digital Laser Sensor SERIES ORDER GUIDE End plates End plates are not supplied with the amplifier. Please order them separately when the amplifiers are mounted in cascade. Appearance Description MS-DIN-E Accessories MS-LS- (Sensor head mounting bracket) For LS-H0 / LS-H90 Foot angled mounting Back angled mounting Material: Stainless steel (SUS0) Two M (length mm 0.7 in) screws with washers [stainless steel (SUS)] are attached. When cascading multiple amplifiers, or when it moves depending on the way it is installed on a DIN rail, these end plates clamp amplifiers into place on both sides. Make sure to use end plates when cascading multiple amplifiers together. Two pcs. per set RF-0 (Reflector) MS-EXL- (Mounting plate for thru-beam type) mm 0.5 in t 0.8 mm t 0.0 in 8. mm 0. in Mounting plate MS-EXL- (Accessory) Material: Stainless steel (SUS0) M screw (Purchase separately.) Designation Description separated Sensor head mounting bracket mounting bracket protective seal Reflector Reflective tape MS-EXL- MS-EXL- MS-EXL-5 MS-DIN- FX-MB RF-0 RF- RF- Sensor head mounting bracket MS-EXL- MS-EXL- Adjustment ± Material: Stainless steel (SUS0) Two M (length mm 0.55 in) screws with washers [stainless steel (SUS)] are attached. For LS-H0 (square side sensing type) Foot angled mounting bracket For LS-H0 (square side sensing type) Universal sensor mounting bracket For LS-H0 (square side sensing type) Back angled mounting bracket Mounting bracket for amplifier 0 sets of communication window seals and connector seal Communication window seal: It prevents malfunction due to transmission signal from another amplifier, as well as, prevents effect on another amplifier. Connector seal: It prevents contact of any metal, etc., with the pins of the quick-connection cable. For coaxial retroreflective type Compact reflector For coaxial retroreflective type Size: t 0. mm t 0.06 in For coaxial retroreflective type Size: t 0. mm t 0.06 in 60 rotation Move vertically 5 mm 0.59 in Material: Die-cast zinc alloy MS-EXL-5 Two M (length mm 0.55 in) screws with washers [stainless steel (SUS)], one M (length 0 mm 0.9 in) hexagon-socket-head bolt [stainless steel (SUS)], and one M hexagon nut [stainless steel (SUS)] are attached. Reflector RF-0 mm 0.57 in Material: Stainless steel (SUS0) Two M (length mm 0.55 in) screws with washers [stainless steel (SUS)] are attached. mm 0.7 in mm 0.95 in Sensing range: 0.0 to m 0.0 to.8 ft Sensing range: Same as the RF-0. Reflective tape RF- 0. mm 0.06 in RF- 9. mm 0.6 in 7.8 mm.09 in 5. mm 0.99 in 0. mm 0.06 in 9. mm 0.6 in mounting bracket MS-DIN- protective seal FX-MB Communication window seal Connector seal

6 Digital Laser Sensor SERIES 06 SPECIFICATIONS Sensor heads Type Item CE marking directive compliance Applicable amplifiers Sensing range (Note,) H SP ST STD LONG U LG HYPR Thru-beam type Coaxial reflective Cylindrical Square type LS-H0 LS-H0 LS-H0 EMC Directive, RoHS Directive LS-50(P), LS-50(P)-C (Note ) 50 mm in 00 mm 7.87 in 00 mm.8 in 50 mm 7.77 in 600 mm.6 in 750 mm 9.58 in Coaxial retroreflective type LS-H to m 0.0 to.8 ft 0.0 to m 0.0 to.8 ft 0.0 to m 0.0 to.8 ft 0.0 to.5 m 0.0 to.9 ft 0.0 to m 0.0 to 6.56 ft 0.0 to.5 m 0.0 to 8.0 ft Spot size Sensing object Operation indicator ø5 mm ø0.97 in approx. or less at a distance from the emitter of ø5 mm ø0.97 in approx. or less at a distance from the emitter of ø mm ø0.079 in approx. or less at a distance from the sensor head of 00 mm.8 in Opaque, translucent, or transparent object (Note 5) Orange LED (lights up when the amplifier output is ON) ø6 mm ø0.6 in approx. or less at a distance from the sensor head of Emitting element Environmental resistance Material Cable Protection Ambient temperature Ambient humidity Ambient illuminance Voltage withstandability Insulation resistance Vibration resistance Shock resistance Type Peak emission wavelength Laser class Max. output IP0 (IEC) IP67 (IEC) IP0 (IEC) IP0 (IEC) 0 to +55 C + to + F (No dew condensation or icing allowed), Storage: 0 to +70 C to +58 F Enclosure: Stainless steel (SUS0) Cover: Polycarbonate 5 to 85 % RH, Storage: 5 to 85 % RH Incandescent light:,000 lx or less at the light-receiving face,000 V AC for one min. between all supply terminals connected together and enclosure 0 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure 0 to 500 Hz frequency,.5 mm in double amplitude in X, Y and Z directions for two hours each mw 00 m/s acceleration (0 G approx.) in X, Y and Z directions three times each Enclosure: PBT Cover: Acrylic 0.09 mm -core shielded cable, m 6.56 ft long (Note 7) Red semiconductor laser diode 660 nm 0.06 mil Class [IEC / JIS / FDA (Note 6)] mw mw mw Enclosure: PBT, Indicator cover: Polycarbonate Beam-emitting/receiving surfaces: Glass 0.5 mm, -core two parallel shielded cables, m 6.56 ft long (Note 7) Weight Accessories Net weight: 50 g approx. Gross weight: 75 g approx. M6 screw: pcs. Toothed lock washer: pcs. Net weight: 50 g approx. Gross weight: 70 g approx. MS-EXL- (Mounting plate): pcs. Net weight: 50 g approx. Gross weight: 80 g approx. MS-LS- (Mounting bracket): pc. Net weight: 50 g approx. Gross weight: 85 g approx. MS-LS- (Mounting bracket): pc. RF-0 (Refrector): pc. Notes: ) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of + C +7. F. ) When using the thru-beam type LS-H0 or LS-H0, do not set the receiving light sensitivity (gctl) of the applicable series amplifier to level or less. This is because there is a possibility of sensing becoming unstable. ) The sensing range of the coaxial reflective type sensor is specified for white non-glossy paper (00 00 mm in) as the object. ) The sensing ranges for coaxial retroreflective type sensors are values for the RF-0 reflector. In addition, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 0.0 m 0.0 ft away. Note that if there are white papers or specular objects near the sensor head, reflected light from these objects may be received. In such cases, use the amplifier unit s receiving sensitivity function to lower the sensitivity, change the response time, or move the sensor head away from the target object. The incident light intensity may vary with the condition of the reflector surface. When using one of the applicable series amplifiers, leave an adequate safety margin when setting the threshold. 5) Make sure to confirm detection with an actual sensor before use. 6) This product complies with CFR 00.0 and 00. Laser Notice No. 50, dated June, 007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration). 7) Cable cannot be extended. separated

7 07 Digital Laser Sensor SERIES separated s Type NPN output Item PNP output CE marking directive compliance Supply voltage Power consumption Sensing outputs (Sensing output, ) (Note ) Sensing output setting Response time External input (Note ) External input function Timer functions Timer period Interference prevention function Protection Environmental resistance SPECIFICATIONS Output operation Short-circuit protection Sensing output Sensing output (Note ) Monitor current output Sensing output operation indicator Laser emission indicator Output select indicator Digital display Incident light indication range Sensitivity setting Logical operation Ambient temperature Ambient humidity Voltage withstandability Insulation resistance Vibration resistance Shock resistance Material Cable Cable extension Weight Accessory Connector type LS-50 LS-50P Cable type LS-50-C LS-50P-C EMC Directive, RoHS Directive +0 to V DC 5 % Ripple P-P 0 % or less Normal operation:,00 mw or less (Current consumption 50 ma or less at V supply voltage,cable type: excluding monitor current output) ECO mode: 980 mw or less (Current consumption 0 ma or less at V supply voltage,cable type: excluding monitor current output) <NPN output type> NPN open-collector transistor Maximum sink current: 50 ma (Note ) Applied voltage: 0 V DC or less (between output and 0 V) Residual voltage: V or less (at max. sink current) <PNP output type> PNP open-collector transistor Maximum source current: 50 ma (Note ) Applied voltage: 0 V DC or less (between output and +V) Residual voltage: V or less (at max. source current) Selectable either Light-ON or Dark-ON Incorporated Normal mode, differential mode, hysteresis mode, window comparator mode, selectable Normal mode, differential mode, hysteresis mode, self-diagnosis output mode, selectable H-SP: 60 μs or less, ST: 50 μs or less, STD: 50 μs or less, LONG: 500 μs or less, U-LG: 5 ms or less, HYPR: ms or less, selectable Output current: Approx. to 0 ma (H-SP, ST, STD: at 0 to,000 indication) Response time: ms or less Zero point: ma ± % F.S. Span: 6 ma ± 5 % F.S. Linearity: ± % F.S. resistance: 0 to 50 Ω <NPN output type> NPN non-contact input Signal condition High: +8 V to +V DC or open, Low: 0 to + V DC (source current 0.5 ma or less) Input impedance: 0 kω approx. Normal mode, differential mode, hysteresis mode, self-diagnosis output mode, answer-back output mode, selectable <PNP output type> PNP non-contact input Signal condition High: + V to +V DC (sink current.0 ma or less), Low: 0 to +0.6 V DC or open Input impedance: 0 kω approx. Laser emission halt / teaching (full-auto teaching, limit teaching, point teaching) / logic operation setting / copy lock / display adjustment / data bank load / data bank save, selectable Orange LED (lights up when sensing output or sensing output is ON) Green LED (lights up during laser emission) Yellow LED (lights up when output is selected) 8-digit 7-segment digital display (-digit green LED + -digit red LED), MODE indicator (Yellow LED): L/D, CUST, PRO H-SP / ST / STD: 0 to,000, LONG / U-LG / HYPR: 0 to 9,999 -level teaching / limit teaching / full auto teaching / manual adjustment Between sensing output and calculation target: Disabled / AND / OR / XOR, selectable Calculation target: Sensing output / adjacent upstream amplifier (sensing output ) / external input, selectable <Sensing output > OFF-delay timer, ON-delay timer, One-shot timer, ON/OFF-delay timer, ON-delay / One-shot timer, switchable either effective or ineffective, with variable timer period <Sensing output > OFF-delay timer, ON-delay timer, One-shot timer, switchable either effective or ineffective, with variable timer period Timer range ms : 0.5 ms approx., to 9,999 ms approx., in approx. ms intervals Timer range sec : 0.5 sec. approx., to sec. approx., in approx. sec. intervals Timer range /0 ms : 0.05 ms approx., 0. to ms approx., in approx. 0. ms intervals, Set separately for each output. Incorporated (Note ) IP0 (IEC) 0 to +55 C + to + F (If to 7 units are mounted close together, 0 to +50 C + to + F; if 8 to 6 units (cable type: 8 to units) are mounted close together, 0 to +5 C + to + F) (No dew condensation or icing allowed), Storage: 0 to +70 C to +58 F 5 to 85 % RH, Storage: 5 to 85 % RH,000 V AC for one min. between all supply terminals connected together and enclosure 0 MΩ, or more, with 50 V DC megger between all supply terminals connected together and enclosure 0 to 50 Hz frequency, 0.75 mm 0.00 in (max. 0 G) double amplitude in X, Y and Z directions for two hours each 98 m/s acceleration (0 G approx.) in X, Y and Z directions five times each Enclosure: Polycarbonate, Cover: Polycarbonate, Switch: Polyacetal 0. mm 6-core cabtyre cable, m 6.56 ft long Extension up to total 00 m 8.08 ft is possible with 0. mm, or more, cable. Net weight: 5 g approx., Gross weight: 55 g approx. Net weight: 75 g approx., Gross weight: 0 g approx. FX-MB ( protective seal): set Notes: ) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of + C +7. F. ) 5 ma if 5 or more amplifier are connected in cascade (excluding cable extension). ) Number of units that can be mounted close together: 0 for H-SP; for ST; for STD, LONG, U-LG, or HYPR ) Select either sensing output or external input as the connector type.

8 Digital Laser Sensor SERIES 08 I/O CIRCUIT AND WIRING DIAGRAMS I/O circuit diagrams NPN output type Connector type Terminal No. of connector type Sensor circuit Tr +. V Tr ZD 0 kω D D D ZD D Color code of quick-connection cable (Brown) +V (Note ) (Black) Sensing output + (White) Sensing output / external input (Blue) 0 V (Note ) * to V DC +0 5 % Cable type +. V 0 kω Sensor circuit Tr Tr ZD D D D D ZD Color code (Brown) +V 6 (Pink) External input + to V DC (Black) Sensing output +0 5 % (White) Sensing output (Blue) 0 V (Gray) Monitor output 5 Internal circuit Users circuit Notes: ) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. ) Wiring when sensing output is selected is shown with solid lines. Wiring when external input is selected is shown with broken lines. Symbols... D, D, D, D: Reverse supply polarity protection diode ZD, ZD: Surge absorption zener diode Tr, Tr : NPN output transistor PNP output type Connector type Terminal No. of connector type Color code of quick-connection cable D (Brown) +V (Note ) Sensor circuit 0V Tr Tr 0 kω D * ZD ZD (White) Sensing output / D external input D (Black) Sensing output (Blue) 0 V (Note ) Internal circuit Users circuit Notes: ) The quick-connection sub cable does not have +V (brown) and 0 V (blue). The power is supplied from the connector of the main cable. ) Wiring when sensing output is selected is shown with solid lines. Wiring when external input is selected is shown with broken lines. Wiring diagrams NPN output type Notes: ) The quick-connection sub cable does not have brown lead wire and blue lead wire. The power is supplied from the connector of the main cable. ) The quick-connection cable does not have gray or pink lead wires. Terminal layout of connector type +V Terminal No. Output 0V Output + + Color code of cable type/quick-connection cable Brown (Note ) Pink Black White Blue (Note ) Gray Symbols... D, D, D, D: Reverse supply polarity protection diode ZD, ZD: Surge absorption zener diode Tr, Tr : PNP output transistor to V DC +0 5 % to V DC +0 5 % * Cable type Sensor circuit D Tr Tr 0V Internal circuit Color code (Brown) +V ZD ZD D (Black) Sensing output + D (White) Sensing output 0 kω 6 (Pink) External input D (Blue) 0 V 5 (Gray) Monitor output to V DC +0 5 % Internal circuit Users circuit * Non-voltage contact or PNP open-collector transistor External input or High: + V to +V (sink current: ma or less) Low : 0 to +0.6 V, or open Light emission halts and teaching occurs when at High. PNP output type Users circuit Non-voltage contact or NPN open-collector transistor External input or High: +8 V to +V, or open Low: 0 to + V (source current: 0.5 ma or less) Light emission halts and teaching occurs when at Low. Color code of cable type/quick-connection cable Brown (Note ) Black White + to V DC Pink +0 5 % Blue (Note ) Gray Notes: ) The quick-connection sub cable does not have brown lead wire and blue lead wire. The power is supplied from the connector of the main cable. ) The quick-connection cable does not have gray or pink lead wires. * Connector for amplifier (CN-EP) pin position Terminal No. Connection cable Purple White Shield Shield 5 5 Black 6 6 Pink separated

9 09 Digital Laser Sensor SERIES PRECAUTIONS FOR PROPER Refer to p.55~ for general precautions and p.59~ for information about laser beam. This catalog is a guide to select a suitable product. Be sure to read the instruction manual attached to the product prior to its use. Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products which meet regulations and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. Cautions for laser beams These products are Class laser in compliance with IEC, JIS standards and FDA* regulations. To reduce the risk of danger, do not look directly at the laser beam or view it through an optical system. A label with instructions as found at the below is affixed to the product. Handle this sensor as per the instruction on the labels. Mounting <How to mount the amplifier> () Fit the rear part of the mounting section of the amplifier on a 5 mm.78 in width DIN rail. () Press down the rear part of the mounting section of the unit on the 5 mm.78 in width DIN rail and fit the front part of the mounting section to the DIN rail. <How to remove the amplifier> () Push the amplifier forward. () Lift up the front part of the amplifier to remove it. Note: Be careful. If the front part is lifted without pushing the amplifier forward, the hook on the rear portion of the mounting section is likely to break. <How to mount the sensor head> () Insert the sensor head connector into the inlet until it clicks. () Fit the cover to the connector. Connector cover 5 mm.78 in width DIN rail Sensor head side connector separated * This product complies with CFR 00.0 and 00. Laser Notice No. 50, dated June, 007, issued by CDRH (Center for Devices and Radiological Health) under the FDA (Food and Drug Administration). Safety standards for laser beam products A laser beam can harm human being s eyes, skin, etc., because of its high energy density. IEC has classified laser products according to the degree of hazard and the stipulated safety requirements. LS-H is classified as Class laser. Classification by IEC Classification Class Part description () Sensing output selection indicator (Yellow) Sensing output selection indicator (Yellow) Laser emission indicator (Green) Sensing output operation indicator (Orange) Sensing output operation indicator (Orange) Description Lasers that are safe under reasonably foreseeable conditions of operation, including the use of optical instruments for intrabeam viewing. Safe use of laser products For the purpose of preventing users from suffering injuries by laser products, IEC (Safety of laser products). Please check the standards before use. (Refer to p.59~ for information about laser beam.) UP key Teaching Threshold value fine adjustment Select setting items Digital display (Green / Red) MODE indicator: L/D (Yellow) MODE indicator: CUST (Yellow) MODE indicator: PRO (Yellow) SET key Teaching Confirm setting contents DOWN key Teaching Threshold value fine adjustment Select setting items MODE key Select Modes Cancel during setting Press down for sec. or more: Switch the sensing output /. Sensor head LS-H0 The tightening torque should be 0.98 N m or less. LS-H0 In case mounting this product, use a metal plate MS-EXL- (accessory). The tightening torque should be 0.5 N m or less with M screws. In case using the dedicated sensor head mounting bracket MS-EXL- (optional) when mounting this product, the metal plate MS-EXL- (accessory) is required depending on the mounting direction. Mount as the diagram below indicates. <Not requiring the metal plate> Metal plate Accessory for MS-EXL- LS-H0, LS-H90 The tightening torque should be 0.5 N m or less. When placing the sensor head horizontally or vertically, the reflector must also be positioned horizontally or vertically Sensor head mounting bracket MS-EXL- (Optional) M (length: mm 0.55 in) screw with washer Accessory for MS-EXL- Metal plate Accessory for MS-LS- 9 mm 0.78 in mm 0.7 in mm 0.5 in Attached toothed lock washer Mounting plate <Requiring the metal plate> Metal plate MS-EXL- (Accessory) as shown in Fig. below. If the sensor head is placed horizontally or vertically but the reflector is tilted as shown in Fig. below, the reflection amount will decrease, which may cause unstable detection. M6 Metal plate MS-EXL- (Accessory) t 0.8 mm t 0.0 in 8. mm 0. in M screw (Purchase separately) mm 0.55 in Sensor head mounting bracket MS-LS- (Accessory) M (length: mm 0.7 in) screw with washer Accessory for MS-LS-

10 Digital Laser Sensor SERIES 0 PRECAUTIONS FOR PROPER Fig. Proper positioning When placing the sensor head horizontally or vertically, the reflector shall also be positioned horizontally or vertically. <Correct> Fig. Improper positioning When placing the reflector tilted even when the sensor head is positioned horizontally or vertically. <Incorrect> DIMENSIONS (Unit mm in) Refer to p.55~ for general precautions and p.59~ for information about laser beam. Wiring Make sure that the power supply is off while wiring. Verify that the supply voltage variation is within the rating. Take care that if a voltage exceeding the rated range is applied, or if an AC power supply is directly connected, the sensor may get burnt or damaged. If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. Make sure to use the optional quick-connection cable for the connection of the amplifier [connector type LS-50(P)]. Extension up to total 00 m 8.08 ft is possible with 0. mm, or more, cable. However, in order to reduce noise, make the wiring as short as possible. Set the supply voltage after considering the voltage drop caused by the cable s resistance. When adding units, wiring length must not exceed 50 m 6.0 ft (for 5 to 8 amplifiers) or 0 m ft (for 9 to 6 amplifiers). Others Do not use during the initial transient time (0.5 sec. approx.) after the power supply is switched on. Because the sensitivity is higher in U-LG and HYPER modes than in other modes, it can be more easily affected by extraneous noise. Check the operating environment before use. The CAD data can be downloaded from our website. LS-50 LS-50P LS-50-C LS-50P-C Sensing output selection indicator (Yellow) Sensing output selection indicator (Yellow) Setting key Sensing output selection indicator (Yellow) Sensing output selection indicator (Yellow) Setting key Laser emission indicator (Green) Sensing output operation indicator (Orange) Sensing output operation indicator (Orange) Digital display (Red, Green) MODE key Laser emission indicator (Green) Sensing output operation indicator (Orange) Sensing output operation indicator (Orange) Digital display (Red, Green) MODE key Suitable for 5 mm.78 in width DIN rail Communication window ( ) R. R Communication window Suitable for 5 mm.78 in width DIN rail ( ) R. R ø ø0.57 in 6-core cable, m 6.56 ft long separated CN-7-C CN-7-C CN-7-C5 Main cable (Optional) CN-7-C CN-7-C CN-7-C5 Sub cable (Optional) Length (L) CN-7-C Length (mm in), L Length (L) CN-7-C Length (mm in), L CN-7-C, CN-7-C5 5, ø. ø0.0 cable CN-7-C, CN-7-C5 5, ø. ø0.0 cable

11 Digital Laser Sensor SERIES DIMENSIONS (Unit mm in) The CAD data can be downloaded from our website. LS-H0 Sensor head LS-H0 Sensor head Beam axis Note: Not incorporated on the emitter. M Operation indicator (Orange) (Note) ø. ø0.6 mouting holes Note: Not incorporated on the emitter Operation indicator (Orange) (Note) Beam axis LS-H0 LS-H90 Sensor head RF Operation indicator (Orange) -ø. ø Reflector (Accessory for LS-H90 ) MS-DIN-E Material: Polycarbonate RF-0 M (length 8 mm in) pan head screw 0.57 Suitable for 5 mm.78 in width DIN rail M square nut End plate (Optional) Reflector (Optional) ø. ø0.6 mounting holes ø. ø0.6. mounting holes separated Material: Acrylic (Reflector) ABS (Base) Material: Acrylic (Reflector) ABS (Base) RF- RF- B Reflective tape (Optional) MS-DIN- mounting bracket (Optional) A Adhesive tape RF- RF- A B ø.8 ø ø. ø0.6 holes 7.06 Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) t t 0.09

12 Digital Laser Sensor SERIES DIMENSIONS (Unit mm in) The CAD data can be downloaded from our website. MS-LS- Sensor head mounting bracket (Accessory for LS-H0, LS-H90 ) MS-EXL- Sensor head mounting bracket for LS-H0 (Optional) R.6 t. R0.99 t ø. ø R.6 R0.99 -M R.5 R0.059 t. t Foot angled mounting bracket R R0.5 t. t t.5 t M Assembly dimensions Mounting drawing with the receiver of LS-H Beamreceiving part R R t..0 t 0.07 Material: Stainless steel (SUS0) Two M (length mm 0.7 in) screws with washers [stainless steel (SUS)] are attached t 0.8 t Material: Stainless steel (SUS0) Note: Screws are not attached. Purchase separately. Assembly dimensions Mounting drawing with the emitter of LS-H0 separated ø.05 ø Beamemitting part Note: Without using the mounting plate, beam misalignment may occur. Back angled mounting bracket R R t. t Material: Stainless steel (SUS0) Two M (length mm 0.55 in) screws with washers [stainless steel (SUS)] are attached. MS-EXL- Mounting plate (Accessory for LS-H0 ) MS-EXL-5 Sensor head mounting bracket for LS-H0 (Optional) M t.5 t Material: Stainless steel (SUS0) Two M (length mm 0.55 in) screws with washers [stainless steel (SUS)] are attached. MS-EXL- Universal sensor mounting bracket ø8.5 ø ø8.5 ø0.5 -hexagon nut seats ø. ø0.6 mounting holes Material: Die-cast zinc alloy Two M (length mm 0.55 in) screws with washers [stainless steel (SUS)], one M (length 0 mm 0.9 in) hexagon socket-head bolt [stainless steel (SUS)], and one M hexagon nut [stainless steel (SUS)] are attached t.5 t ø. ø0.0 thru-hole M Sensor head mounting bracket for LS-H0 (Optional) Assembly dimensions Mounting drawing with the receiver of LS-H Beamreceiving part ø8.5 ø ø. ø0.6 mounting holes (Note) Note: This is the adjustable range of the movable part.