Glossary. The hardware object that defines the interface between the D600 Controller and the NCM.

Size: px
Start display at page:

Download "Glossary. The hardware object that defines the interface between the D600 Controller and the NCM."

Transcription

1 Metasys Network Technical Manual 636 Glossary Section Technical Bulletin Issue Date 1092 Glossary Access Controller Accumulator (ACM) ACM active hub active link AHU Controller alarm latching Analog Data (AD) Analog Input (AI) Analog Output Digital (AOD) The hardware that defines the interface between the D600 Controller and the NCM. The software representation of a binary input device that measures flow or consumption by monitoring a rate of contact or voltage change. See Accumulator. A multi-port repeater used in an N1 LAN star or mixed network configuration to transmit messages and to provide electrical isolation for each node in the network. A 2-port repeater used in an N1 LAN or mixed network configuration if the signal must be regenerated. An Application Specific Controller used for Air Handling Unit (AHU) operations. The AHU may be used as a standalone unit, or connected to the N2 Bus as an element in a Metasys Network. The capability of defining a Binary Input or a Binary Data as a latching point. When an alarm condition occurs, the remains in the alarm state until an operator or control process issues an Unlatch command. A point derived from an analog value that was obtained as the result of a control process, operator entry, or attribute from another. The software representation of a hardware device that is monitoring an analog value. The software representation of a control output used in positioning valves, dampers, and other proportional devices. The AOD is generally used in conjunction with the PID Loop Johnson Controls, Inc. 1 Order No

2 Analog Output Setpoint (AOS) Application Specific Controller (ASC) ARCNET ASC attribute AUTO Auto Restore Binary Data (BD) Binary Input Alarm Point Binary Input (BI) Binary Output (BO) Blink Buffer bumpless transfer The software representation of an analog output device used in position control or remote setpoint adjustment. A family of standalone control devices with hardware and software preconfigured to meet the functional needs of a specific application. The 2.5 megabit/sec., token-passing Local Area Network protocol developed by Datapoint Corporation. A baseband network, which transmits digital signals one message at a time. The Metasys N1 LAN uses ARCNET. See Application Specific Controller. A characteristic or property of an (e.g., a low limit of an analog point) that describes the status and makes it unique. A command that releases the Override command and allows other lower priority inputs to change the current value. A function that restores a device to its correct commanded condition when either communication is resumed after a failure or the NCM is restarted. A point derived from a binary value that was obtained as the result of a control process, operator entry, or attribute from another. One of up to eight binary inputs attached to a Smart Terminal Interface (STI). Binary input alarm points are used to identify breaches in security. The software representation of a Binary Input device that is monitoring a 2-state (On/Off) field condition. The software representation of a 2-state (On/Off) controlled device. An optional user-programmable feature of an Intelligent Lighting Controller that momentarily turns Off the lights in a lighting group to notify occupants that the lights are about to be turned off. Process of temporarily storing data in register or in RAM, that allows transmission devices to accommodate differences in data rates and to perform error checking and re-transmission of data received in error. A software feature that tracks the difference between setpoint and feedback, then gradually resolves the differences to reach setpoint when control changes from manual to automatic operating modes. 2 Glossary

3 bus bus network C210 Controller C260 Controller CAL1 (Custom Applications Language One) Card Reader Card Reader Change-of-State (COS) Change-of-State Reporting Cleaning Crew Cold Start A transmission path wherein devices on a given medium receive all transmissions at the same time, but process only those addressed to them. One of three available configurations for the Metasys N1 LAN. The bus network configuration consists of a layout in which the nodes are connected in a daisy chain fashion. A preprogrammed Application Specific Controller with standalone capabilities used primarily for the monitoring and control of Variable Air Volume (VAV) box controllers. A preprogrammed Application Specific Controller with standalone capabilities used primarily for water source heat pump control. A programming language used to define the programs and data base of the DSC-8500 hardware. A device that translates information on an access card and sends it, via a Smart Terminal Interface (STI), to the D600 Controller data base for verification. Up to 16 card readers can be included in an IAC-600 Access Control System. A software that represents one Smart Terminal Interface/Card Reader combination in an IAC-600 Access Control System. For a point, the act of transferring from one condition to another in realtime (e.g., a Binary Input point changing from Normal to Alarm). Passing of a COS event to an Input/Output (I/O) device for priority display. An ILC feature that interlocks lighting groups so janitorial crews can turn On assigned lighting groups in the area about to be cleaned. This automatically turns Off lights in the previous cleaning area. Restarting the Network Control so that it is operating out of Erasable Programmable Read-Only Memory (EPROM) based code. When the Network Control is cold started, both code and data need to be downloaded and stored within Dynamic Random-Access Memory (DRAM) to return to normal operations. Contrast with warm start. Glossary 3

4 Communication Terminal Board (TBC) connectivity control Control System (CS) COS D600 Controller Data Base Manager Data Definition Language (DDL) DDA DDE DDL deadband definable Definition window A termination board that allows NCU communication across the N1 LAN. The board also terminates the N2 and L2 Buses to the NCU/NEU. The ability to link together two or more computers or systems for the purpose of communication, data transfer, etc. The name of the software definition of a specific process that combines multiple field devices (point s) to perform a function. The software representation of selected hardware and internal points in an Application Specific Controller (ASC). Typically, the CS represents one control strategy (e.g., temperature control or static pressure control) located in a controller, though it may represent more than one strategy. See Change-of-State. The IAC-600 System intelligent access controller, which performs security management functions within Metasys. A collection of subroutines (program code) used to read from and write tasks to records, feature records, and control strategy records. Text-oriented software program for creating global and data bases. See Dynamic Data Access. See Dynamic Data Exchange. See Data Definition Language. See normalband. The capability of being defined, applies to attributes of an that the operator may set a value for. For example, when you enter a System Name and Object Name for an, you are defining these two attributes. See Object Definition window. 4 Glossary

5 Demand Limiting Dial-Up I/O Differential Digital Control (DCM) Directory Manager Disable download DOS Dynamic Data Access (DDA) Dynamic Data Exchange(DDE) Enable Engineering Units A control strategy that monitors and compares power demand over a sliding interval. It then projects average power demand during the interval and temporarily turns Off selected equipment to avoid exceeding predetermined demand peak targets. A software feature that provides automatic phone connections between NCUs and remotely located Operator Workstations and printers. An optional software setting to reduce excessive alarm and warning reports, caused by fluctuations above and below set limits. A point interface and control module that resides in either the NCU or NEU. It functions as a co-processor for the NCM, providing Proportional Integral Derivative (PID) algorithms to independently regulate modulating devices. The DCM is equipped with universal inputs and universal outputs. A software program that facilitates information flow throughout the network. It helps the software find attribute data quickly so information can be passed on to other controllers and operator devices. A command that stops an from triggering control processes, sending COS messages to operator devices, and accepting commands (except for Enable). Passing of a program and data bases from an operator device to a NCU. Disk Operating System. The communications concept designed by Johnson Controls Inc., that allows the Metasys Network to communicate with every component on an equal basis with complete freedom of information transfer. A message passing protocol defined by Microsoft Corporation as a Windows standard that allows the exchange of information between two independent Windows applications. A command that resets the Disable command and allows the to trigger control processes, send COS reports to operator devices, and accept other commands. An operator-defined analog unit (such as DEGF or CFM) that has been defined by the user to be associated with a specific value. Glossary 5

6 Ethernet Router Facility Management System (FMS) Feature fiber optic active link file Fire Controller Fire Management FM FMS Focus window Function Keys Function (FM) Gateway Global Data Sharing A Metasys component that integrates Metasys N1 LAN segments with an Ethernet network that uses the TCP/IP protocol. The router provides the physical connection between the Metasys ARCNET segment and the Ethernet network. A combined network system of Operator Workstations, Network Control Units, Network Expansion Units, Application Specific Controllers, Network Terminals, and points used to control and monitor a building or group of buildings. A software program that uses data from s to perform building control operations (i.e., Totalization, Demand Limiting, or Point History). A device that is used for media conversion between coax and optical fiber. See record. The hardware that defines the interface between the IFC-1010 or IFC-2020 Fire Alarm Controller and the Fire NCM. A software set in the NCM that provides Metasys control over the IFC-1010 or IFC-2020 Fire Controller. See Function. See Facility Management System. A detailed summary that contains attributes for a specific. See also Object Focus window. Special keys on an I/O device that can perform frequently used functions with a single keystroke. A sensor/controller conditioning device that interfaces a field device to a DCM and in some cases an XM. See JC/85 Gateway. Generally used to describe a method of defining current point data values as accessible to other devices. The Dynamic Data Access feature in Metasys goes beyond Global Data Sharing by making all values and all attributes from all network s accessible throughout the network. 6 Glossary

7 GPL Graphic Programming Language (GPL) Group Name Hand-Off-Auto (HOA) Hardware Object Manager hardware record hardware s high voltage HOA HVAC PRO IAC-600 Intelligent Access Control System IAP Function IBF Function IBN Function See Graphic Programming Language. A symbol-based language used to define control strategies and data bases for a Metasys Network. One of the three hierarchical name levels for s used to assist the user with grouping s within summaries more clearly at an Operator Workstation. The other hierarchical name levels for s are Network Name and System Name. A manual hardware override switch located on the XRL Point Multiplex and some Function s. The HOA switch either places the contacts into the same position as if the relays were turned On (H), if the relays were turned Off (O), or places the relays under automatic (A) control. A software program that transmits data from the NCM to the N2 or L2 Bus. A record that contains information on the physical location of an within the network. The name of the software definition for an operator device, printer, or a controller. A voltage value equal to or greater than 480 VAC. See Hand-Off-Auto. The standard Metasys software tool for creating control strategies for Application Specific Controllers. The system that automatically controls access to a facility by the use of access cards (badges). The IAC-600 System is comprised of a D600 Controller, up to 16 Smart Terminal Interfaces (STIs) and card readers, and up to 128 binary input alarm points. See Input Analog Pneumatic Function. See Input Binary Frequency Function. See Input Binary Function. Glossary 7

8 IDP Function IFC-1010 Controller IFC-2020 Controller ILC Input Analog Pneumatic (IAP) Function Input Binary Frequency (IBF) Function Input Binary (IBN) Function ) Input Differential Pressure (IDP) Function Input Universal (IUN) Function Intelligent Lighting Controller (ILC) IUN Function JC/85 Gateway L2 Bus See Input Differential Pressure Function. A 2 loop, 198 device intelligent analog addressable fire alarm system that performs fire management functions within Metasys. A 10 loop, 1980 device intelligent analog addressable fire alarm system that performs fire management functions within Metasys. See Intelligent Lighting Controller. Interfaces incoming field signals to the DCM by converting the pneumatic input pressure signal into a proportional analog signal for use by the DCM (multiple ranges available). Interfaces incoming field signals to the DCM by sensing field data (such as rapidly cycling contact closures or input voltages), and converting the input frequency to a DC voltage for use by the DCM. Interfaces incoming field signals to the DCM by converting field data from two different binary inputs to a DC voltage range for use by the DCM. Interfaces incoming field signals to the DCM by converting differential pressure signals into a proportional analog signal for use by the DCM. Interfaces incoming current, voltage or resistance signals to either the DCM or to an XM that is inserted in a DCM slot. A programmable ASC that performs On/Off control of building light circuits and other switchable loads. It can operate either as a standalone controller or be integrated into the Metasys Network. See Input Universal Function. A software set providing a special application of the NCM to integrate Metasys information with the JC/85 CPU. In the Gateway application, the NCM serves as a high-level protocol translator, making Metasys information available to a JC/85 headend. A local communication network that connects the C210 Application Specific Controller or the C260 Application Specific Controller to an NCM. 8 Glossary

9 Lab and Central Plant (LCP) Controller LAN Laptop Computer LCP line-voltage Load Rolling Load table Local Area Network (LAN) low-voltage manual commands mapping s message Metalink Metastat An Application Specific Controller used for single chiller or boiler plant control applications, or for controlling the HVAC process of a laboratory environment. See Local Area Network. A portable version of the Operator Workstation. See Lab and Central Plant Controller. A voltage value of not less than 42 VAC RMS and not more than 479 VAC. An energy saving feature that temporarily turns Off equipment to meet a specified energy reduction target. Used with the Demand Limiting and Load Rolling features to define which loads have been selected as shed candidates and the priority in which they must be shed. Each load table may have up to four priorities defined. A combination of hardware and software that enables Operator Workstations and NCMs to share data base information, hardware resources, and application programs. A voltage value of less than 42 VAC RMS. All available commands entered manually at an Operator Workstation or Network Terminal. Corresponding a set of values having defined parameters with the quantities or values of another set. User-defined ASCII text that can be associated with a COS report. An optional feature of Metasys that allows the exchange of information between Metasys and independent third-party software applications such as Microsoft Excel. It provides a Microsoft Windows Dynamic Data Exchange (DDE) interface to Metasys. A family of temperature sensing products designed for use with Application Specific Controllers. Glossary 9

10 Metasys Metasys Integrator Migration mixed network Multiplex Binary (XBN) Multiplex Relay Electrically Maintained (XRE) Multiplex Relay Latched (XRL) Multiplex Relay Momentary (XRM) N1 LAN N2 Bus NCM NCSETUP An evolutionary distributed Facility Management System, designed by Johnson Controls, Inc. A type of Network Control (NCM200) that allows qualified thirdparty controllers to be connected to the N2 Bus, much like the standard ASCs. The connectivity provides greater flexibility in FMS design, implementation, and system evolution. See S2 Migration. One of three available configurations for the Metasys N1 LAN. The mixed network configuration consists of a combination of the star and bus network components. A Point Multiplex that monitors up to 32 binary inputs and reports changes in their states to the NCU for processing. A Point Multiplex that monitors up to eight binary inputs and executes output commands through eight electrically maintained relays. The XRE also reports input changes-of-state and HOA switch settings to the NCU for processing. A Point Multiplex that monitors up to eight binary inputs and executes output commands through eight magnetically latched relays. The XRL also reports input changes-of-state and HOA switch settings to the NCU for processing. A Point Multiplex that monitors eight binary inputs and executes output commands through eight momentary relay pairs. The XRM also reports input changes-of-state and Auto/Manual switch settings to the NCU for processing. An ARCNET local area network that interconnects NCUs and Operator Workstations. A local Optomux network that interconnects ASCs, XMs, and NEUs to an NCU. See Network Control. A software program, running on a laptop PC or the Operator Workstation, that configures each NCM. 10 Glossary

11 NCU NEU Network Network Control (NCM) Network Control Unit (NCU) Network Expansion Unit (NEU) Network Manager Network Map Network Name Network Port Network Terminal (NT) See Network Control Unit. See Network Expansion Unit. A collection of Operator Workstations, printers, NTs, NCUs, NEUs, ASCs, N1 LANs, and N2 Buses which make up a FMS. The main processing module in the Network Control Unit. Fully programmable, the NCM coordinates and supervises the control activities for all s and control loops hardwired to the NCU, as well as the remote NEUs and Application Specific Controllers connected to it over a local N2, L2, or S2 Bus. A standalone panel used to control a building s mechanical equipment. The NCU consists of an enclosure, door, and baseframe to house electronic modules (an NCU must include a Network Control ), terminal blocks, and signal conditioners. It is highly flexible in hardware and software configuration and provides direct digital control, energy management, supervisory control, and point monitoring. A remote field panel to expand the I/O point and control loop capacity of the NCU. The NEU contains the same configurable modules as the NCU, but without the NCU s user-programmable main processor, the Network Control (NCM). A software program responsible for dynamically updating the screen with realtime data. The first screen to appear on an Operator Workstation after logging on. It displays the structure of the recently activated network in true diagram form. One of the three hierarchical name levels for s used to assist the user with grouping s within summaries more clearly at an Operator Workstation. The other hierarchical name levels for s are System Name and Group Name. A Metasys component that monitors and controls the Metasys FMS from a third-party computer serving as a host. The Network Port emulates the Allen-Bradley PLC -5 Programmable Logic Controller. A hand-held operator s device used to access point data, change operating parameters and schedules, and perform overrides at the NCU. Glossary 11

12 Network Terminal Emulator Network Tool Box Network Transparency NEU Node normalband NT OAE Function OAI Function OAP Function OBE Function Object Definition window Object Focus window Object Identifier Object Manager An IBM PC, AT, or PS/2 computer, or a Toshiba laptop loaded with NT Emulation software. The NT Emulator can perform the same functions as the Network Terminal. An optional diagnostic package for the Operator Workstation. A characteristic of the Metasys Network. Network transparency allows the operator to view information about a facility without knowledge of, or restriction from the physical devices in which that information is stored. See Network Expansion Unit. Any addressable device connected to the N1 LAN. A node can be a Network Control or an Operator Workstation. Defines the width of the normal operating range for s. See Network Terminal. See Output Analog Electrical Function. See Output Analog Isolated Function. See Output Analog Pneumatic Function. See Output Binary Electrical Function. A software data base record that corresponds to and characterizes a field device, a data point, an N2 address, or a control function. Used to define an online at an Operator Workstation. Used to view the condition of an existing and/or modify attributes online at an Operator Workstation. The name identifying a specific in a system. The Object Identifier is a 2-part name (up to 16 characters in length) consisting of a System Name and an Object Name. Software that resides in the NCU and is used to control and characterize s. 12 Glossary

13 Object Oriented Architecture Operator Workstation Optomux ORE Function ORL Function ORM Function OSV Function OTE Function Output Analog Electrical (OAE) Function Output Analog Isolated (OAI) Function Output Analog Pneumatic (OAP) Function Output Binary Electrical (OBE) Function Output Relay Electrical Maintained (ORE) Function Output Relay Latched (ORL) Function A software design technique where information about a specific item is stored so that it is readily available to users and application programs. All the attributes of an are stored at the same place as the. A Personal Computer-based operator interface used for sophisticated information management, data storage, and system programming. Communications protocol used on the N2 Bus. See Output Relay Electrical Function. See Output Relay Latched Function. See Output Relay Momentary Function. See Output Solenoid Valve Function. See Output Triac Electrical Function. Interfaces between the DCM and analog output field devices. It may be configured to source analog output voltage, source analog output current, or modulate current for externally powered devices. Provides an isolated interface between the DCM and analog output field devices. It may be configured to source analog output voltage, source analog output current, or modulate current for externally powered devices. Interfaces between the DCM and field devices to provide pneumatic pressure control. Interfaces between the DCM and field devices to provide incremental control of a field device. Interfaces between the DCM and field devices to provide On/Off control for the field devices via electrically maintained relays. Interfaces between the DCM and field devices to provide On/Off control for the field devices via magnetically latched relays. Glossary 13

14 Output Relay Momentary (ORM) Function Output Solenoid Valve (OSV) Function Output Triac Electrical (OTE) Function Override Password PID Loop (PIDL) PIN (Personal Identification Number) Code PMI Point History Point Multiplex (XM) point Process Interfaces between the DCM and 2-state field devices to provide On/Off control for the field devices via momentary relays. Interfaces between the DCM and field devices to provide 3-way solenoid air valve control of a pneumatic output signal to field devices. Interfaces between the DCM and field devices to provide increment/decrement control. A manual command available at the Operator Workstation or Network Terminal. It allows the operator to define a current value for an output at a high priority. Override replaces the current value with the userdefined value. A global security feature that restricts access to the system from the Operator Workstation or Network Terminal. Used to manipulate outputs for closed-loop control at a given Digital Control. The PID Loop is the software that generates these outputs by using a collection of inputs and other variables to perform calculations and issue commands. A number that must be entered at a card reader keypad in order to gain access to a facility. Person/Machine Interface. A feature that maintains a recent history of the values, actions, status, and flags associated with each point. A family of binary sensor/controller interface devices that reside in the NCU or NEU. See also XBN, XRE, XRL, and XRM. Software that corresponds to and characterizes field devices and data points. There are eight types of point s: Accumulator, Analog Data, Analog Input, Analog Output Digital, Analog Output Setpoint, Binary Data, Binary Input, and Binary Output. A self-sufficient, modular block of computer instructions for an NCM. Processes are used to implement control strategies. 14 Glossary

15 Pseudo point Ranging Realtime Operating System (RTOS) record Repeater report Report Router/Alarm Management RTOS S2 Migration sample Scheduling Security Key segment Also called Data or Duplicate point. May be a duplicate definition (copy) of an actual physical point or the result of a calculation or logical operation in a control process like GPL. A function that converts the analog-to-digital counts from the field into data for operator use. Johnson Controls multi-tasking operating system. It provides an environment in which several programs can run simultaneously. Formatted data representation for the Report Router. An adapter card that extends the length of the N2 Bus beyond 5000 feet, or increases the number of N2 devices beyond 50. A specialized grouping of displayed points not solicited by the user. A central distribution system for messages and files. It displays critical Alarms in custom windows, allowing flexible operator processing of Alarms and reports. See Realtime Operating System. A software set in the NCM that brings JC/85 field gear, information, and control directly into Metasys from the JC/85 trunks. Each individual polled event (i.e., a snapshot of parameter values). A feature that allows the user to schedule commands and summaries individually by the following parameters: time, day of week, and holiday. Optimizes energy use while providing flexible scheduling for individual and system variations. A module that plugs into the parallel port of the Operator Workstation. It is required to run Metasys PMI software and protect from illegal use and copying of the software. For the N1 LAN, an electrically continuous section of cable that is terminated at both ends (i.e., does not pass through an active hub or active link). For the N2 Bus, an electrically continuous daisy-chained cable between repeaters or repeaters to end-of-line. Glossary 15

16 Self-Tuning PID Control Smart Terminal Interface (STI) Software Model Software Object Manager Software Object Record Staff Workstation standalone star network System Directory System Name System/Object Name TBC Time Manager A software feature that automatically and continually modifies (fine-tunes) PID Loop parameters to maintain a correct output value. One of up to 16 terminals linked to the D600 Controller in an IAC-600 Access Control system. An STI controls card reader and door security hardware, and monitors a group of local binary input alarms. Its associated card reader reads access cards. A predefined set of attributes used as a default for defining Control System (CS) software s. A software program that obtains information from records in order to perform building control operations. A software record that contains attribute data pertaining to the operation of the. A Metasys software option that serves as a complete Metalink application. It provides users with simple and convenient access to temperatures, humidities, and setpoints. The source code of the application is provided and can be customized by the applications engineer. The ability of a controller to perform a defined set of functions without supervisory control on any other device. One of three available configurations for the Metasys N1 LAN. The star network configuration consists of two or more nodes connected to a multiport repeater called an active hub. Part of the NCM s Directory Manager. The system directory lists which systems are defined for each specific NCM. One of the three hierarchical name levels for s used to assist the user with grouping s within summaries more clearly at an Operator Workstation. The other hierarchical name levels for s are Network Name and Group Name. See Object Identifier. See Communication Terminal Board. A software program that keeps track of the time of day, day of week, date, holiday, and alternate or regular schedules. 16 Glossary

17 Time-Out Time Scheduling Token Token bus Token passing Totalization Trend Triggerable Unitary Controller (UNT) Upload/Download User Programs An action performed by the Operator Workstation and Network Terminal that automatically logs off the screen if the keyboard isn t used within a user-specified period of time. See Scheduling. A unique combination of software bits that grant a specific node on the N1 LAN permission to transmit. A Local Area Network (LAN) that features a layout in which the nodes are wired in a daisy chain. It uses a 2-port repeater called an active link for expansion. A local network access mechanism in which a token is passed from node to node in sequential order; nodes must wait for the token to arrive for access to the network to transmit data. Feature for counting the number of occurrences of particular events or accumulating totals of the quantity of a particular commodity as it is used, processed, or encountered. There are four types of Totalization: analog, runtime, pulse, and event. A user-defined monitoring feature which gathers the data needed to review the performance of an entire building or of an individual piece of equipment. The capability of being triggered; applies to an attribute that can cause (trigger) another operation to occur. For example, if an analog input temperature sensor goes into high Alarm, it can cause a binary output to start a supply fan. An Application Specific Controller used for digital control of package air handling units, unit ventilators, fan coils, heat pumps, and other terminal units serving a single zone or room. Exchanges data between the NCM and Operator Workstation. This process may be automatic (in the case of a NCM request following power loss), or it may be a manual request from the user (through the Operator Workstation). Executes calculations, sequences of operation, control logic, interlocks, and other supervisory control programs written in GPL. Glossary 17

18 Variable Air Volume (VAV) Controller Warm Start writable XM XBN Point Multiplex XRE Point Multiplex XRL Point Multiplex XRM Point Multiplex Zone Zone Terminal (ZT) ZT An Application Specific Controller used for digital control of single duct, dual duct, fan powered, and supply/exhaust VAV box applications. Restarting the Network Control so that remains fully operational following initial diagnostic tests. When the Network Control is warm started, both code and data remain safely stored within Dynamic Random-Access Memory (DRAM). Contrast with cold start. The capability of being written to; applies to attributes the operator may modify (or write to). See Point Multiplex (XM). See Multiplex Binary (XBN). See Multiplex Relay Electrically Maintained (XRE). See Multiplex Relay Latched (XRL). See Multiplex Relay Momentary (XRM). A software that represents one IFC-2020 fire zone residing in an IFC-2020 Fire Alarm Controller. A hand-held or wall-mounted device that is used to monitor and adjust your HVAC system within a specific building zone. See Zone Terminal. 18 Glossary

19 Notes Glossary 19

20 Notes Controls Group FAN E. Michigan Street Metasys Network Technical Manual P.O. Box 423 Release 4 Milwaukee, WI Printed in U.S.A. 20 Glossary

Lab and Central Plant Controller

Lab and Central Plant Controller Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 0290 Lab and Central Plant Controller The Metasys Lab and Central Plant (LCP) Controller is

More information

Digital Control Module 140

Digital Control Module 140 Metasys Network Technical Manual 636 Control Modules Section Technical Bulletin Issue Date July 28, 2003 Digital Control Module 140 Introduction Page 2 Description 2 Theory of Operation 2 Engineering 6

More information

Polling the N2 Network or Zone Bus for Devices

Polling the N2 Network or Zone Bus for Devices Metasys Checkout Tool User s Guide 3-1 Chapter 3 Polling the N2 Network or Zone Bus for Devices Introduction The first step in the checkout process is using the Metasys Checkout Tool to find and display

More information

Metasys Smoke Control Wiring

Metasys Smoke Control Wiring Metasys Network Technical Manual 636 Smoke Control Section Technical Bulletin Issue Date 1199 Metasys Smoke Control Wiring Metasys Smoke Control Wiring Page 3 Overview 3 References 4 Power Entry 5 Metasys

More information

Extended Digital Controller

Extended Digital Controller The Metasys Extended Digital Controller Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 1093 Extended Digital Controller (DX-9100) is the

More information

Metasys System Extended Architecture Overview

Metasys System Extended Architecture Overview Technical Bulletin Issue Date March 31, 2003 Metasys System Extended Architecture Overview Metasys System Extended Architecture Overview...2 Introduction... 2 Key Concepts... 4 Metasys System Extended

More information

DX-9100 Digital Controller, Version 2

DX-9100 Digital Controller, Version 2 Metasys European Sales Resource Manual Application Specific Controllers Section Product Bulletin Issue Date 1298 DX-9100 Digital Controller, Version 2 The DX-9100 Digital Controller is the ideal digital

More information

Metasys Checkout Tool User s Guide

Metasys Checkout Tool User s Guide Table of Contents Metasys Checkout Tool User s Guide Chapter 1 Using This Guide...1-1 Introduction... 1-1 Key Concepts... 1-2 Chapter Organization...1-2 Chapter 2 Introduction to the Metasys Checkout Tool...2-1

More information

Defining Points. Introduction

Defining Points. Introduction M-Series Workstation with Companion/Facilitator Manual 9-1 Chapter 9 Defining Points Introduction This chapter explains how to define software points. Points are software representations of input and output

More information

APPLICATION NOTE JC/85

APPLICATION NOTE JC/85 Metasys Network Technical Manual 636 App. Notes: Network Communications Section Application Note Issue Date 0401 APPLICATION NOTE JC/85 Gateway Introduction Page 3 Application Details *3 Hardware and Software

More information

UNT1100 Series. Binary Output Jumpers AO2 AO1 AO3 AO4 AOCM AOCM AOCM AOCM AO1. AI Switches Job Information N2 Address. Ref N2+ N2- ADDR 0 = ALL OPEN

UNT1100 Series. Binary Output Jumpers AO2 AO1 AO3 AO4 AOCM AOCM AOCM AOCM AO1. AI Switches Job Information N2 Address. Ref N2+ N2- ADDR 0 = ALL OPEN 1 2 8 4 AI6 R R Installation Bulletin UNT1100 Issue Date 0309 UNT1100 Series Introduction The Unitary (UNT) controller (UNT1100 Series) is a digital controller with applications for air handling units,

More information

Discontinuation of N2 and Select LONWORKS Field Controllers and Associated Products. Notice of Plans for Long-Term Support of N2 Devices.

Discontinuation of N2 and Select LONWORKS Field Controllers and Associated Products. Notice of Plans for Long-Term Support of N2 Devices. : December 2, 2011 Announcing: From: Released To: Advanced Notice of Product of N2 and Select LONWORKS Field Controllers. Notice Of Plans For Long Term Support Of N2 Devices Metasys System Product Management

More information

CF Terminal User s Guide

CF Terminal User s Guide Table of Contents CF Terminal User s Guide Chapter 1 Using This Guide...1-1 Introduction... 1-1 Key Concepts... 1-2 Chapter Organization...1-2 Questions or Comments...1-2 Chapter 2 Getting Started...2-1

More information

Binary Input (BI) Object

Binary Input (BI) Object Metasys etwork Technical Manual 636 Objects Section Technical Bulletin Issue Date 1199 Binary Input (BI) Object Introduction Page 3 Quick Start *3 Engineering Overview 9 Overview of Operation *9 Hardware

More information

Output Relay Latched Function Module

Output Relay Latched Function Module Metasys Network Technical Manual 636 Function Modules Section Technical Bulletin Issue Date 0793 Output Relay Latched Function Module Introduction Page 3 Description 3 Application 4 Capabilities 4 Theory

More information

TC-9102 Terminal Controller

TC-9102 Terminal Controller Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 1095 TC-9102 Terminal Controller The TC-9102 Terminal Controller, the latest addition to the

More information

BCPro System Product Bulletin

BCPro System Product Bulletin CH-BCM100-0, CH-BCM200-0 Introduction The BCPro system from Johnson Controls is ideally suited to automating the environmental control and energy usage functions of conventional buildings. Not only does

More information

N1 Migration with the NIE

N1 Migration with the NIE Technical Bulletin Issue Date April 29, 2003 N1 Migration with the NIE N1 Migration with the NIE...3 Introduction... 3 Key Concepts... 4 N1 Migration Overview... 4 N1 Migration Flowchart... 5 Metasys N1

More information

Introduction to the N30 Supervisory Controller

Introduction to the N30 Supervisory Controller N30 Supervisory Controller User s Manual 2-1 Chapter 2 Introduction to the N30 Supervisory Controller Introduction This chapter describes the basic functions and operation of an N30 Supervisory Controller

More information

M-Tool. Features and Benefits System Configuration and Project Management. Allows fast adjustment and commissioning of systems

M-Tool. Features and Benefits System Configuration and Project Management. Allows fast adjustment and commissioning of systems Product Bulletin Issue Date July 6, 2006 Supersedes June 30, 2004 M-Tool M-Tool transforms the way you create control strategies by providing a suite of tools with an intuitive and efficient work environment.

More information

Control System (CS) Object

Control System (CS) Object Metasys Network Technical Manual 636 Objects Section Technical Bulletin Issue Date 0101 Control System (CS) Object Introduction Page *3 Quick Start *3 Overview of Concepts *6 Software Models *9 Engineering

More information

Analog Data (AD) Object

Analog Data (AD) Object Issue Date 11/01/01 TECHICAL BULLETI Analog Data (AD) Object Introduction Page 2 Applications 2 Quick Start 3 Engineering 9 Overview of Operation 9 Input Processing 12 Alarm Limit Analysis 25 Triggers

More information

Analog Input (AI) Object

Analog Input (AI) Object Issue Date April 9, 2003 TECHNICAL BULLETIN Analog Input (AI) Object Analog Input (AI) Object...3 Introduction... 3 Key Concepts... 4 Defining the AI... 4 Modifying and Monitoring the AI... 6 Overview

More information

SECTION REMOTE CONTROL PANELS

SECTION REMOTE CONTROL PANELS SECTION 25 14 13 REMOTE CONTROL PANELS PART 1. GENERAL 1.01 SECTION INCLUDES: A. Building Controller (BC) B. Advance Application Specific Controller (AAC) C. Application Specific Controller (ASC) 1.02

More information

N2 Dialer Module. Features and Benefits

N2 Dialer Module. Features and Benefits Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 1194 N2 Dialer Module The N2 Dialer Module (NDM) provides a low-cost method of connecting

More information

Appendix C: HVAC PRO Modules

Appendix C: HVAC PRO Modules FANs 637.5, 1637.5 Appendix Section Issue Date 0400 APPLICATION NOTE Appendix C: HVAC PRO Modules HVAC PRO Modules...3 Introduction...*3 Key Concepts...*4 ABS VALUE... 6 ADD... 6 ANALOG OUTPUT... 6 AND...

More information

Output Relay Electrical Function Module

Output Relay Electrical Function Module Metasys Network Technical Manual 636 Function Modules Section Technical Bulletin Issue Date 0294 Output Relay Electrical Function Module Introduction Page 3 Description 3 Application 4 Capabilities 4 Theory

More information

Variable Air Volume Modular Assembly (VMA) 1400 Series

Variable Air Volume Modular Assembly (VMA) 1400 Series Product Bulletin Issue Date March 27, 2009 Variable Air Volume Modular Assembly (VMA) 1400 Series The Variable Air Volume Modular Assembly (VMA) Series is a family of configurable digital controllers.

More information

Onboard Inputs and Outputs. Remote User Interface. Integral LCD User Interface

Onboard Inputs and Outputs. Remote User Interface. Integral LCD User Interface Product Bulletin: FX06 Field Controller Issue Date: March 2006 FX06 Field Controller The FX06 is a compact field controller in the Facility Explorer range of products. The controller is designed specifically

More information

FXVMA Variable Air Volume (VAV) Box Controller

FXVMA Variable Air Volume (VAV) Box Controller FXVMA Product Bulletin FXVMA Issue Date November 21, 2008 FXVMA Variable Air Volume (VAV) Box Controller The FXVMA is an integrated assembly used to control Variable Air Volume (VAV) boxes. The FXVMA consists

More information

Key Features and Benefits

Key Features and Benefits System Description Since its beginning, Automated Logic has focused on one objective: to develop innovative building automation systems with the latest technologies, which advance operational freedom,

More information

Johnson Controls ComBus Quick Tester

Johnson Controls ComBus Quick Tester Johnson Controls ComBus Quick Tester MS-CQT485-0 Documentation Number: MS-CQT485-0_0405m pn#6550 Contents Section 1: Introduction - Controls & Features... 1 ComBus Quick Tester... 1 Figure 1 - End & Front

More information

FCU-4 FAN COIL CONTROLLER

FCU-4 FAN COIL CONTROLLER FCU-4 FAN COIL CONTROLLER BACnet Enabled Description The FCU-4 is designed to provide complete control of fan coil units. The FCU-4 incorporates all the inputs and outputs to ensure that this advanced

More information

Metasys Integrator Allen-Bradley Custom Application

Metasys Integrator Allen-Bradley Custom Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 0998 APPLICATION NOTE Metasys Integrator Allen-Bradley Custom Application Introduction Page 3 Application

More information

Metasys Integrator Multistack Application

Metasys Integrator Multistack Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 0998 APPLICATION NOTE Metasys Integrator Multistack Application lntroduction Page *3 Application Details

More information

Network Terminal. Features and Benefits. Metasys Network Sales Resource Manual 635 Operator Devices Section Product Bulletin Issue Date 0190

Network Terminal. Features and Benefits. Metasys Network Sales Resource Manual 635 Operator Devices Section Product Bulletin Issue Date 0190 Metasys Network Sales Resource Manual 635 Operator Devices Section Product Bulletin Issue Date 0190 Network Terminal The Network Terminal (NT) can put the precise facility management capabilities of Metasys

More information

Andover ContinuumTM. b3850 Series Terminal Controllers

Andover ContinuumTM. b3850 Series Terminal Controllers TM b3850 Series Terminal Controllers The TM b3850 series controllers are native BACnet controllers that communicate on an RS-485 field bus as Master devices using the MS/TP BACnet protocol. 02 Features

More information

Appendix A: N1 OPC Data Access Server

Appendix A: N1 OPC Data Access Server Issue Date July 14, 2003 TECHNICAL BULLETIN Appendix A: N1 OPC Data Access Server Appendix A: N1 OPC Data Access Server...3 Introduction... 3 Key Concepts... 4 N1... 4 OLE... 4 OPC... 4 Site... 4 N1 OPC

More information

Andover ContinuumTM Infinet II

Andover ContinuumTM Infinet II Andover ContinuumTM Infinet II i2920 System Controllers The Andover Continuum Infinet II i2920 System Controller is designed to meet the needs of your most demanding control and monitoring applications

More information

Dual Duct Controller - One Air Velocity

Dual Duct Controller - One Air Velocity Technical Specification Sheet Rev. 4, December, 1998 Dual Duct Controller - One Air Velocity Sensor gure 1. Dual Duct Con ontr troll ller One Air Velocity Sen ensor. The Dual Duct Controller (re 1) is

More information

Network Control Module 300 Series

Network Control Module 300 Series Technical Bulletin Issue Date October 20, 2004 Network Control Module 300 Series Network Control Module 300 Series...3 Introduction... 3 Key Concepts... 7 NCM... 7 ISA Bus Cards... 10 Installation Considerations...

More information

M1000 INTELLIGENT ZONE CONTROL SYSTEM

M1000 INTELLIGENT ZONE CONTROL SYSTEM HARDWARE GUIDE DIMENSIONS & SPECIFICATIONS REV. 5.2 M1000 INTELLIGENT ZONE CONTROL SYSTEM ROOFTOP CONTROLLER 2 Table of Contents GENERAL INFORMATION... 3 PL-M1000 Rooftop Controller...3 Description...3

More information

Metasys System Configuration Tool (SCT)

Metasys System Configuration Tool (SCT) Product Bulletin Issue Date March 31, 2003 Metasys System Configuration Tool (SCT) As an integral part of the Metasys system extended architecture, the System Configuration Tool (SCT) supports the engineering,

More information

Metasys N1 Network Integration

Metasys N1 Network Integration Product Bulletin Issue Date March 31, 2003 Metasys N1 Network Integration The Metasys N1 Network Integration solution connects existing Metasys N1 based building automation systems into the new generation

More information

PRO3200 Professional Modular Access Control Hardware

PRO3200 Professional Modular Access Control Hardware PRO3200 Access Control Hardware As a part of the WIN-PAK software controlled hardware family the PRO3200 professional modular access control hardware is an advanced access control panel capable of providing

More information

Electrical Demand Specification (Reference SOP: )

Electrical Demand Specification (Reference SOP: ) Project: Equipment Description: Location: Equipment No.: Project No: Protocol No.: Content Index 1. GENERAL...3 Design Standards...3 1.1. Standards...3 2. DESIGN...3 2.1. Safety...3 2.2. Circuit protection...3

More information

oom Pressurization Con

oom Pressurization Con Technical Specification Sheet Rev. 3, December, 1998 Room Pressurization Controllers equipment. This approach to room control includes the following features. Features gure 1. Roo oom Pressurization Con

More information

Tracer Controls. Tracer MP501 Controller BAS-PRC008-EN. January 2005

Tracer Controls. Tracer MP501 Controller BAS-PRC008-EN. January 2005 Tracer Controls Tracer MP501 Controller January 2005 BAS-PRC008-EN Introduction The Tracer MP501 controller is a configurable, multi-purpose controller used to provide direct-digital control for heating,

More information

Metasys Integrator United Power Application

Metasys Integrator United Power Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 0998 APPLICATION NOTE Metasys Integrator United Power Application lntroduction Page 3 Application Details

More information

PRO2200 Professional Modular Access Control Hardware

PRO2200 Professional Modular Access Control Hardware PRO2200 Access Control Hardware As a part of the WIN-PAK software controlled hardware family the PRO2200 professional modular access control hardware is an advanced access control panel capable of providing

More information

The Simply Smart Way to Optimize Building Control and Performance

The Simply Smart Way to Optimize Building Control and Performance Connected Buildings ComfortPoint Open Building Management System The Simply Smart Way to Optimize Building Control and Performance For Consultants and Specifiers ComfortPoint Open BMS. Simply Smart. Honeywell

More information

Safety Instructions 1-1 Avoid unintended Start General Description 2-2

Safety Instructions 1-1 Avoid unintended Start General Description 2-2 Contents Contents 1 Safety and precautions 1-1 Safety Instructions 1-1 Avoid unintended Start. 1-1 2 Introduction 2-1 General Description 2-2 3 Supported Configuration 3-1 Introduction 3-1 Fixed-speed

More information

Static Pressure High Limit

Static Pressure High Limit Metasys Network Technical Manual 636 Air Handlers Section Technical Bulletin Issue Date 0590 Static Pressure High Limit Static pressure high limit File Name Path Name Main Function Accessories How It Works

More information

Network Control Unit Network Expansion Unit

Network Control Unit Network Expansion Unit Metasys Network Technical Manual 636 Network Units Section Technical Bulletin Issue Date 0692 Network Control Unit Network Expansion Unit Introduction Page 3 Application Overview 3 - Network Control Module

More information

clarity 3 Programmable Controller

clarity 3 Programmable Controller clarity 3 Programmable Controller BACnet General Purpose Controllers (B-AAC) DESCRIPTION Taco Clarity 3 FPC series controllers are designed to control building systems and HVAC equipment. The integrated

More information

Smart Equipment Controls (SEC)

Smart Equipment Controls (SEC) Smart Equipment Controls (SEC) Product Bulletin SE-SPU1001-0, SE-SPU1002-0, SE-SPU1011-0, SE-SPU1011-0, SE-SPU1012-0, SE-SPU1004-0, SE-FDD1001-0, SE-ECO1001-0, SE-COM1001-0 Code No. LIT-12011934 Issued

More information

FX Input/Output (I/O) Modules XM07 and XM14

FX Input/Output (I/O) Modules XM07 and XM14 Product Bulletin FX I/O Modules Issue Date July 6, 2009 FX Input/Output (I/O) Modules XM07 and XM14 The FX Input/Output (I/O) Modules provide additional physical input and output points for FX field controllers

More information

Introduction to Programmable Logic Controllers (PLC's)

Introduction to Programmable Logic Controllers (PLC's) Introduction to Programmable Logic Controllers (PLC's) Industrial Control Systems Fall 2006 Lecture Introduction to PLC's MME 486 Fall 2006 1 of 47 The Need for PLCs Hardwired panels were very time consuming

More information

WSHP-IOP-2 May Installation, Operation, and Programming. Tracer ZN510 Controller

WSHP-IOP-2 May Installation, Operation, and Programming. Tracer ZN510 Controller WSHP-IOP-2 May 1998 Installation, Operation, and Programming Tracer ZN510 Controller Literature History The Trane Company has a policy of continuous product improvement and it reserves the right to change

More information

Wireless Metasys System

Wireless Metasys System Metasys Product Bulletin Code No. LIT-12011244 Software Release 5.0 Issued January 4, 2010 Supersedes February 25, 2009 The Metasys provides a wireless platform for multiple levels of the Johnson Controls

More information

Using Loop Tuning for ASC Devices

Using Loop Tuning for ASC Devices HVAC PRO User s Guide 13-1 Chapter 13 Using Loop Tuning for ASC Devices Introduction Use Loop Tuning to monitor and/or tune Proportional plus Integral (PI) process control loops for ASC devices. This chapter

More information

FCU-4 FAN COIL CONTROLLER

FCU-4 FAN COIL CONTROLLER FCU-4 FAN COIL CONTROLLER BACnet Enabled Description The FCU-4 is designed to provide complete control of fan coil units. The FCU-4 incorporates all the inputs and outputs to ensure that this advanced

More information

PRODUCT BULLETIN. M-Graphics. modifications. graphic development

PRODUCT BULLETIN. M-Graphics. modifications. graphic development Product Bulletin Issue Date 06/18/04 PRODUCT BULLETIN M-Graphics Unparalleled ease, speed, and power; it s all at your fingertips with M-Graphics, the premier dynamic graphical interface in the facility

More information

N1 Migration with the NIE Technical Bulletin

N1 Migration with the NIE Technical Bulletin MS-NIE55xx-x, MS-NxE85SW-0, MS-NIE8500-x Code No. LIT-20535 Software Release 9.0 Issued August 207 Refer to the QuickLIT website for the most up-to-date version of this document. Document Introduction...3

More information

Q9 ASD LOW VOLTAGE DRIVE

Q9 ASD LOW VOLTAGE DRIVE ASD LOW VOLTAGE DRIVE HVAC-MINDED, SYSTEM FRIENDLY RELIABLE Toshiba has manufactured pulse-width modulated drives since 1981 and is one of the few companies that manufactures both motors and drives in

More information

BACnet. b3810 Series Local Controllers

BACnet. b3810 Series Local Controllers BACnet b380 Series Local Controllers The Andover Continuum TM b380 series controllers are designed for control of Air Handling Units, Roof Top Units, and other mechanical plant equipment. 0 Features Choose

More information

Metasys Integrator Caterpillar Application

Metasys Integrator Caterpillar Application Application Note Issue Date May, 00 APPLICATION NOTE Metasys Integrator Caterpillar Application Introduction Application Details Component Requirements Vendor Contact Information Design Considerations

More information

FX Tools Express Software Package

FX Tools Express Software Package Product Bulletin FX Tools Express Issue Date October 31, 2005 FX Tools Express Software Package FX Tools Express is a Windows based software package for configuring, downloading and commissioning of predefined

More information

What a BACnet system looks like and how it can be used generally depends. By Roland Laird

What a BACnet system looks like and how it can be used generally depends. By Roland Laird This article was published in ASHRAE Journal, November 2009. Copyright 2009 American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. Posted at www.ashrae.org. This article may not

More information

Andover ContinuumTM Infinet II

Andover ContinuumTM Infinet II Andover ContinuumTM Infinet II i2850 Series The i2850, i2851, and i2853 controllers provide cost-effective DDC control of individual terminal units (e.g. VAV boxes, fan-powered induction units, unit ventilators,

More information

ECLYPSE Series Connected IP and Wi-Fi Product Series and Accessories

ECLYPSE Series Connected IP and Wi-Fi Product Series and Accessories S o l u t i o n G u i d e Series IP and Product Series and Accessories Overview The series is a range of connected BACnet/IP controllers and accessories that are used to control a wide range of HVAC equipment

More information

Metasys and Companion

Metasys and Companion Metasys Network Technical Manual 636 App. Notes: Operator Devices Section Technical Bulletin Issue Date 0191 Metasys and Companion Application Page 3 Purpose of Application 3 Setting Up the Windows Terminal

More information

Product Catalog. Tracer Controller MP501 BAS-PRC008-EN. May 2012

Product Catalog. Tracer Controller MP501 BAS-PRC008-EN. May 2012 Product Catalog Tracer Controller MP501 May 2012 BAS-PRC008-EN Copyright 2012 Trane. All rights reserved. This document and the information in it are the property of Trane and may not be used or reproduced

More information

ExactLogic BACnet Communicating Zone Damper EXL01710 Sequence Datasheet

ExactLogic BACnet Communicating Zone Damper EXL01710 Sequence Datasheet ExactLogic BACnet Communicating Zone Damper EXL01710 Sequence Datasheet DataSheet ev 1.12.302/4.3 October 27, 2014 Operating Sequence Standard Occupied During normal occupied operation the display will

More information

PEAK TM. PEAK TM controllers. Mid-Market BAS Smart equipment controllers. HVAC/R controllers

PEAK TM. PEAK TM controllers. Mid-Market BAS Smart equipment controllers. HVAC/R controllers Virtual Branch ecatalogue click here controllers HVAC/R controllers The PEAK 18 and PEAK 32 Controllers are configurable controllers that can be switched between MS/TP, Modbus RTU, and N2 Communication

More information

IQ-MP Gateway. Version apr Electrocom Rødeledsvej 95 DK-5700 Svendborg Denmark Tel :

IQ-MP Gateway. Version apr Electrocom Rødeledsvej 95 DK-5700 Svendborg Denmark Tel : IQ-MP Gateway Version 4.009 28. apr. 2011 Electrocom Rødeledsvej 95 DK-5700 Svendborg Denmark Tel : +45 8880 7580 www.electrocom.dk p. 2 Description The IQ-MP Gateway is a communications module, which

More information

Medium User Interface (MUI) Version 3

Medium User Interface (MUI) Version 3 Medium User Interface (MUI) Version 3 Product Bulletin Medium User Interface (MUI) Issue Date October 21, 2009 The MUI is a remote user interface device for the FX Platform that supports FX06, FX07, FX14,

More information

Andover ContinuumTM Infinet II

Andover ContinuumTM Infinet II Andover ContinuumTM Infinet II The i80 Series controllers are designed for control of Air Handling Units, Roof Top Units, and other mechanical plant equipment. Features 0 Choose the i80 model with the

More information

Suitable for a wide range of installations with wall-mount, flush-mount and hand-held remote control options.

Suitable for a wide range of installations with wall-mount, flush-mount and hand-held remote control options. TUC03 Configurable Terminal Unit Controller Product Bulletin The TUC03 Configurable Terminal Unit Controller is designed specifically to provide direct digital control of terminal unit applications with

More information

Accord Builder. User Guide

Accord Builder. User Guide User Guide Document: V 3.6 User Guide R01 V3.6 User Guide R01 Page 1 of 110 Table of Contents 1 Introduction... 7 2 General Summary and Definitions... 8 2.1 Accord Platform and Plant... 8 2.2 PLC Control

More information

Product Data. Features/Benefits. 50RLP Water Source Heat Pumps System Control Panel

Product Data. Features/Benefits. 50RLP Water Source Heat Pumps System Control Panel Product Data 0RLP Water Source Heat Pumps System Control Panel TM Single packaged system control panel for use with Aquazone water source heat pumps in stand-alone or direct digital control applications

More information

Metasys Integrator Graham Application

Metasys Integrator Graham Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 0496 APPLICATION NOTE Metasys Integrator Graham Application Introduction Page 3 Application Details 3

More information

PW6000 Modular Access Control System PW6000 Intelligent Controllers and Modules

PW6000 Modular Access Control System PW6000 Intelligent Controllers and Modules Modular Access Control System The next generation of the PW-Series family improves on the existing PW technology to offer superior features and benefits. The PW-Series Modular Control System is an advanced

More information

Building Energy Management Training Systems

Building Energy Management Training Systems Building Energy Management Training Systems 3466-00 LabVolt Series Datasheet Festo Didactic en 120 V - 60 Hz 03/2019 Table of Contents General Description 2 Courseware 2 Topic Coverage 2 List of Available

More information

Andover ContinuumTM Infinet II

Andover ContinuumTM Infinet II Andover ContinuumTM Infinet II TAC continues to provide powerful, state-of-the-art controllers to keep up with tomorrow s fast-paced world. The Andover Continuum Infinet II (i2) family of controllers are

More information

Tracer Controls. Tracer MP.501 Controller BAS-PRC008-EN. June 2001

Tracer Controls. Tracer MP.501 Controller BAS-PRC008-EN. June 2001 Tracer Controls Tracer MP.501 Controller June 2001 BAS-PRC008-EN Introduction The Tracer MP.501 controller is a configurable, multi-purpose controller used to provide direct-digital control for heating,

More information

Metasys System Extended Architecture

Metasys System Extended Architecture Product Bulletin Issue Date March 31, 2003 Metasys System Extended Architecture The architecture of the Metasys building automation and facilities management system has been extended to be fully compatible

More information

XT-9100 Technical Bulletin

XT-9100 Technical Bulletin System 9100 Technical Manual 636.4 Technical Bulletins Section Technical Bulletin Issue Date 0896 XT-9100 Technical Bulletin XT-9100 Extension Module/XP-910x Expansion Modules Page 3 Introduction 3 SX

More information

Metasys Integrator GE Lighting Application

Metasys Integrator GE Lighting Application Metasys Connectivity Technical Manual 629.5 Metasys Integrator Section Application Note Issue Date 0998 APPLICATION NOTE Metasys Integrator GE Lighting Application lntroduction Page 3 Application Details

More information

Commercial Controls. Advanced control for saving time and money

Commercial Controls. Advanced control for saving time and money L Connection NetWork Commercial Controls Advanced control for saving time and money The efficient way to control hvac and building operations L Connection Network at a glance: Controls a wide range of

More information

Spreadsheet Applications

Spreadsheet Applications Metasys Network Technical Manual 3 App. Notes: Network Communications Technical Bulletin Issue Date 9 Spreadsheet Applications lntroduction Page 3 Metasys and Spreadsheet Applications 5 Locating and Opening.DBF

More information

DUKE UNIVERSITY DESIGN & CONSTRUCTION STANDARDS

DUKE UNIVERSITY DESIGN & CONSTRUCTION STANDARDS 1 25 95 00 Integrated Automation Control Sequences for HVAC GENERAL The HVAC operational sequences in this guideline are commonly used by Duke University. They are being provided as a preferred design

More information

PWGSC Ontario EMCS: BUILDING CONTROLLERS Section Region Project Page 1 Number R

PWGSC Ontario EMCS: BUILDING CONTROLLERS Section Region Project Page 1 Number R Region Project Page 1 PART 1 - GENERAL 1.1 SUMMARY.1 Related Sections:.1 Section 25 05 01 - EMCS: General Requirements..3 Section 25 30 02 - EMCS: Field Control Devices. 1.2 REFERENCES.1 American Society

More information

BUILDING MANAGEMENT. OpenBAS-HV-NX10 SERIES CATALOG NUMBER. Description. Features

BUILDING MANAGEMENT. OpenBAS-HV-NX10 SERIES CATALOG NUMBER. Description. Features BUILDING MANAGEMENT OpenBAS-HV-NX10 SERIES Description Mircom s OpenBAS-HV-NX10 series of Building Automation Controllers are aimed to provide various HVAC, energy management, and lighting control solutions

More information

LTEC Heat Pump DDC Controller

LTEC Heat Pump DDC Controller Document No. 09 Rev., May, 00 LTEC Heat Pump DDC Controller Product Description These instructions explain how to install or replace a LTEC (LonMark Terminal Equipment Controller) HP (Heat Pump) DDC Controller

More information

BACnet Protocol Implementation Conformance Statement

BACnet Protocol Implementation Conformance Statement BACnet Protocol Implementation Conformance Statement Date: December 1 st, 2015 Vendor Name: Danfoss A/S Product Name: VLT HVAC Drive FC-102 Product Model Number: FC-102 Applications Software Version: 1.6

More information

WCC III Training Guide

WCC III Training Guide www.wcc-controls.com WCC III Training Guide WattMaster Controls, Inc. 8500 NW River Park Drive Parkville, MO 64152 Toll Free PH: (866) 918-1100 PH: (816) 505-1100 FAX: (816) 505-1101 E-mail: mail@wattmaster.com

More information

32MP Gateway. Overview and Configuration Manual

32MP Gateway. Overview and Configuration Manual 32MP Gateway Overview and Configuration Manual 32MP Gateway Overview and Configuration Manual This document is the property of Carrier Corporation and is delivered on the express condition that it is not

More information

DataNab it8: Intelligent Communicating Thermostat

DataNab it8: Intelligent Communicating Thermostat DataNab it8: Intelligent Communicating Thermostat CONTENTS: - Title Page (This Page) Page 1 - Description Page 2 - Technical Specs Page 2 - Features Page 2 - Dimensions Page 2 - Installation Page 3 Page

More information

Andover ContinuumTM. Family of Controllers. BACnetTM

Andover ContinuumTM. Family of Controllers. BACnetTM TM BACnetTM Family of Controllers BACnet that is intelligent... at every level. Open standards provide building owners with flexibility and choice when selecting building automation technology. The BACnet

More information