SERIES 5 TABLES/BENCH

Size: px
Start display at page:

Download "SERIES 5 TABLES/BENCH"

Transcription

1 Wire Manager Driveshaft Driveshaft Cover Stretcher Power Cable Low-Voltage Cable Power Supply Master Motor (can be on either side) Controller Controller Cable Lifting Column Foot SERIES 5 TABLES/BENCH Troubleshooting Guide Slave Motor (can be on either side) Top Mounting Plate DETAILS SERIES 5 TABLES: HOW THEY WORK Each Lifting Column contains a mechanical lift mechanism that requires an external force to operate. Lifting Columns and Motors are connected to and mechanically synchronized with each other through a telescoping Driveshaft assembly. Two individual electric motors a Master Motor and a Slave Motor provide torque to operate the Lifting Columns. The Master Motor controls all aspects of Table motion, and contains internal stops that define the top and bottom of the range of motion. The Slave motor follows control signals sent from the Master Motor, and only follows what the Master Motor does. Slave Motors have no internal stops. Only two Motors are used to drive the Lifting Columns, regardless of whether the Table has two or three Lifting Columns. The Power Supply contains a power transformer. This converts high-voltage AC current from the wall outlet (120v/60Hz) to low-voltage 24v DC current, which powers the Motors. Only the main Power Cable carries high-voltage. All other cables are low-voltage. The Controller is the user-interface to the Table, and directs all Table movements via the up-down buttons.

2 READ THE ASSEMBLY DIRECTIONS AND USER GUIDE! The Assembly Directions and User Guide are available as free public downloads at steelcase.com/details. Many times, problems can be the result of improper assembly. Were the Assembly Directions followed in the assembly of your Table? If you are absolutely certain that the Table was assembled correctly, then work through the following troubleshooting steps. TROUBLESHOOTING PARTS KIT Having a spare part that is known to work will quickly lead to accurate identification of faulty components. Without this, it can be little more than guesswork. Details strongly recommends that every Dealer maintain a small kit of parts for troubleshooting purposes. This kit of parts should include: Tables Bench 1. Lifting Column qty=2 Service Part no DSR SR 2. Master Motor qty=1 Service Part no DSR DSR 3. Slave Motor qty=1 Service Part no DSR DSR 4. Motor Hardware Package qty=1 Service Part no SR SR 5. Low Voltage Cable qty=1 Service Part no DSR DSR 6. Controller qty=1 Service Part no SR SR 7. Controller Cable qty=1 Service Part no DSR DSR 8. Power Supply qty=1 Service Part no DSR DSR 9. Power Cable qty=1 Service Part no DSR DSR Always maintain a complete kit of troubleshooting spare parts that are known to work properly, to quickly identify the root-cause of problems and resolve customer issues on the first try. TROUBLESHOOTING STEPS Step 1: Step 2: Step 3: Step 4: Check for power at the wall outlet: ensure Table is properly assembled, and all cables are securely connected. Check all connections of Low Voltage Cables. Check that the Power Cable is fully seated in the Power Supply. Check that the mounting bolt is installed through the front of the Master Motor. This deactivates the internal kill switch (see Fig 1, page 5) Check that the center Lifting Column on 90 3-leg Tables are assembled in the correct orientation. Refer to the section on 90 Corner Tables in the Assembly Directions. 2

3 COMMON PROCEDURES SYNCHRONIZING MOTORS AND LIFTING COLUMNS: The Lifting Columns and Motors of Series 5 Tables are synchronized mechanically. The Master Motor and all Lifting Columns must be in the lowest position, before the Driveshafts are installed. If the Table will not go up or down all the way, and no clicking sounds from the Lifting Columns or other signs of damage are observed, the Lifting Columns and Master Motor may need to be synchronized. For ease of access, remove all loads from the Table, and flip the Table upside-down. Slide all Driveshafts out of all Lifting Columns, Motors, and Gearboxes. With the Driveshafts removed, plug the Power Supply into the wall, and press the Down key on the Controller. Operate the Motors all the way to the lowest position, at which point the Motors will stop. Unplug Power Supply from the power outlet. Push all Lifting Columns to their lowest position. Do not push too hard at the bottom of the range of motion, allow 1/8" of play before they hit full-bottom. Reinstall all Driveshafts. It may be necessary to lift up on the Lifting Columns slightly, in order to align the hex openings in the Lifting Columns with the hex shafts of the Driveshafts. Once the Table has been properly reassembled, operate the Table all the way up and all the way down to confirm proper function. Refer to the Assembly Directions as necessary. CHECKING LIFTING COLUMN GEARS: If a Lifting Column reaches a certain point in its travel and stops, a clicking sound may be observed. This could indicate broken gear teeth inside the Lifting Column. For safety and ease of access, remove all loads from the Table, and flip the Table upside-down. Remove the Stretcher, Driveshaft, and Motor (if applicable) from the suspect Lifting Column. Hold the suspect Lifting Column assembly firmly in place on the floor on its glides. With both hands, grip the Top Mounting Plate and raise the Lifting Column all the way up, so that it is fully extended, at its highest position. Using an 8 mm hex socket, remove the four bolts that hold the Top Mounting Plate in place. Remove the Top Mounting Plate. While looking down at the gears inside the top of the Lifting Column, slowly push the Lifting Column down, observing the gears as they turn. If any gear teeth are damaged or missing, the Lifting Column must be replaced. Any faulty Lifting Column must be replaced. There are no field-servicable parts inside the Lifting Column. OBTAINING REPLACEMENT PARTS Contact your local Steelcase dealer to help identify and order Service Parts. If you need help, call 888.STEELCASE. 3

4 TROUBLESHOOTING: CAUSES AND SOLUTIONS PROBLEM POTENTIAL CAUSE POTENTIAL SOLUTION No Power - amber light on Power Supply is not illuminated, or is blinking No power at wall outlet Power Cable not plugged into wall outlet Check outlet with other device; check circuit breakers/fuses/wiring Confirm proper cable engagement into wall outlet Table will go neither up nor down Table goes up, but not down (or vice-versa) Power Cable not fullyseated into Power Supply Faulty Power Cable Table wiring not properly assembled Faulty Power Supply No Power Table is severely overloaded Master Motor kill switch activated Master Motor locked (where equipped) Faulty Controller Faulty Controller Cable Damaged or faulty Low Voltage Cable Faulty Master Motor Faulty Slave Motor Faulty Controller Faulty Controller Cable Damaged or faulty Low Voltage Cable Damaged pins inside multi-pin connectors (Low Voltage Cables / connectors) Faulty Master Motor Check for proper cable engagement into Power Supply. (See Fig. 2, page 5) Inspect the Power Cable for damage; replace any damaged cables. Check that all cables are connected per the Assembly Directions. The Power Supply light should be glowing amber, and not blinking. Swap with a Power Supply known to work. See above Maximum Table capacity is 195 lbs., including the weight of the worksurface. Overloading the Table could lead to damage that would not be covered by warranty. Install front motor mounting bolt per Assembly Directions; this deactivates the internal kill switch located inside the bolt hole at the front of the Master Motor housing. (See Fig. 1, page 5) Unlock Master Motor with provided key; if key is missing, replace with new Master Motor. Most Master Motors are not equipped with a lock. Swap with Controller known to work. Swap with Controller Cable known to work. Unplug Table from wall. Unplug each multi-pin connection point, and inspect the pins. Are they all straight, and making good contact? If not, try using a push-pin to straighten them. Otherwise, replace any damaged cables. (Fig. 3, page 5) Swap with Master Motor known to work. Swap with Slave Motor known to work. Swap with Controller known to work. Swap with Controller Cable known to work. Carefully check the condition of the wiring harness of each Lifting Column. Swap with cable known to work. Use an ohm meter to check cables; resistance should be near zero. High resistance indicates a fault. Unplug Table from wall. Unplug each multi-pin connection point, and inspect the pins. Are they all straight, and making good contact? If not, try using a push-pin to straighten them. Otherwise, replace any damaged cables. (See Fig. 3, page 5) Swap with Master Motor known to work. 4

5 TROUBLESHOOTING: CAUSES AND SOLUTIONS PROBLEM POTENTIAL CAUSE POTENTIAL SOLUTION Table does not go through full range of motion;...and / or... Legs not synchronized (one leg is higher than other) Motors and Lifting Columns not synchronized at Table assembly Faulty Lifting Column Synchronize the Motors and Lifting Columns (see Common Procedures). Is there a clicking sound at any point in the travel of the Table? An internal gear may be stripped or missing teeth (see Common Procedures). Replace any faulty Lifting Columns. Note: Be sure to explore the full range of travel. If one Lifting Column clicks at a certain point, push on the Table to help get it past that point, so that you can explore the full range of Table motion. Why? Because another Lifting Column may have the same problem at a different height. 3-Leg Tables: Center Lifting Column moves in opposite direction vs. other Lifting Columns Table moves in opposite direction after up/down button is released Table movement is not smooth; Lifting Columns jerk or hop while raised or lowered Center Lifting Column installed in wrong orientation. Faulty Master Motor Lifting Columns are not parallel with one another, causing them to bind Faulty Lifting Column Refer to the section on 90 Corner Tables in the Assembly Directions. Reassemble Table per the Assembly Directions. Swap with Master Motor known to work. Ensure Table is unloaded and level. Loosen (but do not remove) all of the screws attaching the Lifting Columns to the Worksurface. For Series 5 tables, also loosen the set-screws on the Stretcher. Operate the Table through a complete up/down cycle and then retighten set-screws and worksurface attachment screws. Still binding? Take everything off the Table, flip it upside-down, and remove the screws completely. Run the Table through another up-down cycle. The position of the Lifting Columns may shift slightly, reinstall all screws in the adjusted position. Is there a clicking sound at any point in the travel of the Table? An internal gear may be stripped or missing teeth (see Common Procedures). Replace any faulty Lifting Columns. Note: Be sure to explore the full range of travel. If one Lifting Column clicks at a certain point, push on the Table to help get it past that point, so that you can explore the full range of Table motion. Why? Because another Lifting Column may have the same problem at a different height. PROBLEM ILLUSTRATIONS Fig. 1 - Front mounting bolt must be installed in Master Motor to deactivate internal kill switch Fig. 2 - Power Cable not fully seated in Power Supply Fig. 3 - Damaged pins in the Low Voltage wiring connectors, housed in the master motors BOLT MISSING WRONG DAMAGED CORRECT CORRECT CORRECT 5

6 Part No Rev. B For further information, please visit steelcase.com/details or call P.O. Box 1967 / CD-5E / Grand Rapids / MI / Steelcase Inc. All rights reserved. All specifications subject to change without notice. Trademarks used herein are the property of Steelcase Inc. or of their respective owners. Printed in U.S.A.

Power Cable. Low-Voltage Cable

Power Cable. Low-Voltage Cable Troubleshooting Guide Power Cable Low-Voltage Cable Wire Manager Power Supply Driveshaft Driveshaft Cover Master Motor (can be on either side) Controller Controller Cable Lifting Column Foot Stretcher

More information

SERIES 7/9 TABLES & SERIES 8 BENCH. Troubleshooting Guide

SERIES 7/9 TABLES & SERIES 8 BENCH. Troubleshooting Guide Troubleshooting Guide Cable Manager Low-Voltage Cable Stretcher Power Cable Controller Control Box Lifting Column Foot SERIES 7/9 TABLES & SERIES 8 BENCH HOW THEY WORK Each Lifting Column contains an individual

More information

SERIES 7 TABLES PRE-DECEMBER Troubleshooting Guide. IMPORTANT NOTE: This guide applies to models shipped prior to December 2015 only.

SERIES 7 TABLES PRE-DECEMBER Troubleshooting Guide. IMPORTANT NOTE: This guide applies to models shipped prior to December 2015 only. Troubleshooting Guide Control Box (PRE-DECEMBER 2015) Low-Voltage Cable Cable Manager Controller Lifting Column Stretcher Foot Power Cable SERIES 7 TABLES PRE-DECEMBER 2015 HOW THEY WORK Each Lifting Column

More information

OLOGY HEIGHT-ADJUSTABLE DESKS. Troubleshooting Guide

OLOGY HEIGHT-ADJUSTABLE DESKS. Troubleshooting Guide Troubleshooting Guide Power Cable Cantilevers Control Box Low-Voltage Cable Controller Lifting Column Foot Understructure OLOGY HEIGHT-ADJUSTABLE DESKS HOW THEY WORK Each Lifting Column contains an individual

More information

OLOGY HEIGHT-ADJUSTABLE DESKS. Troubleshooting Guide

OLOGY HEIGHT-ADJUSTABLE DESKS. Troubleshooting Guide Troubleshooting Guide Power Cable Cantilevers Control Box Low-Voltage Cable Controller Lifting Column Foot Understructure OLOGY HEIGHT-ADJUSTABLE DESKS HOW THEY WORK Each Lifting Column contains an individual

More information

OLOGY HEIGHT-ADJUSTABLE DESKS AND BENCHES. Troubleshooting Guide

OLOGY HEIGHT-ADJUSTABLE DESKS AND BENCHES. Troubleshooting Guide Troubleshooting Guide Power Cable Cantilevers Control Box Active Touch Controller Lifting Column Foot Understructure OLOGY HEIGHT-ADJUSTABLE DESKS AND BENCHES HOW THEY WORK Each Lifting Column contains

More information

OV1000 Part No OV1000 HEIGHT ADJUSTABLE TABLE USER GUIDE

OV1000 Part No OV1000 HEIGHT ADJUSTABLE TABLE USER GUIDE OV1000 Part No. 23624 OV1000 HEIGHT ADJUSTABLE TABLE USER GUIDE PRODUCT OVERVIEW User Guide: OV1000 OV1000 HEIGHT ADJUSTABLE TABLE A healthier work environment starts with the option to sit or stand throughout

More information

OV1001 Part No OV1001 HEIGHT ADJUSTABLE TABLE USER GUIDE

OV1001 Part No OV1001 HEIGHT ADJUSTABLE TABLE USER GUIDE OV1001 Part No. 23620 OV1001 HEIGHT ADJUSTABLE TABLE USER GUIDE PRODUCT OVERVIEW User Guide: OV1001 OV1001 HEIGHT ADJUSTABLE TABLE A healthier work environment starts with the option to sit or stand throughout

More information

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly

Z-Truck (Vertical Moving) Z-truck Flag. Y-Truck (Horizontal Moving) FIGURE 1: VIEW OF THE Z-TRUCK. Flexshaft Assembly Replacing the LCD Cable To remove and replace the LCD Cable you will need the following tools: #2 Phillips screwdriver (magnetic tip preferred) Socket wrench with 10mm socket Removing the Side Panel 1.

More information

Lightning Stitch Assembly

Lightning Stitch Assembly ABM International, Inc. 1 1.0: Parts List Lightning stitch motor and drive assembly (Qty. 1) Lightning stitch piggy backed controller board assembly (Qty. 1) Touchscreen (Qty. 1) 2 9-pin Serial cable (Qty.

More information

ALL-FLEX ELECTRIC TABLE BASE

ALL-FLEX ELECTRIC TABLE BASE ALL-FLEX ELECTRIC TABLE BASE FLEX2 V3 Rev 01 7 /17 Model FLEX2-SLV-V3 Model FLEX2-BLK-V3 Model FLEX2-WHT-V3 ASSEMBLY AND OPERATION ALL-FLEX ELECTRIC TABLE BASE PARTS AND TOOLS PLEASE REVIEW these instructions

More information

CENTRO 6451/6452 LIFT DESK

CENTRO 6451/6452 LIFT DESK CENTRO 6451/6452 OWNER S MANUAL Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products.

More information

MY-HITE ADJUSTABLE TABLE

MY-HITE ADJUSTABLE TABLE Y-HITE ADJUSTABLE TABLE odel Number : FSQAHT Please Read Instructions Before Use ASSEBLY INSTRUCTIONS Tools Needed Thank you for choosing Friant. We appreciate the trust and confidence you have placed

More information

ABM International, Inc. Lightning Stitch Checklist 9/13/2013

ABM International, Inc. Lightning Stitch Checklist 9/13/2013 ABM International, Inc. Lightning Stitch Checklist 9/13/2013 1) Piggy backed board assembly (1) Piggy back board assembly tested? Yes No 24v passed XB passed XA passed YB passed YA passed SAFE passed S/S

More information

SEQUEL 6051/6052 LIFT DESK

SEQUEL 6051/6052 LIFT DESK SEQUEL 6051/6052 customerservice@ OWNER S MANUAL Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to

More information

X/Y Issues on ASP-645-1

X/Y Issues on ASP-645-1 X/Y Issues on ASP-645-1 Issues seen with X or Y problems: A) Table will not move in X or Y when you are using the Frame Arrow buttons on the control panel. B) On power up the control panel gives Error

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PARTS REQUIRED efloat Parts A A (1) Top Frame (consists of two separate weldments) B (2) Legs C D (2) Feet (1) Smart Controller - 7.3 (186.2 mm) x 3.9" (100.4 mm) D E (1) Touchpad

More information

HEIGHT ADJUSTMENT. Manual Crank - Front/Top Mounted

HEIGHT ADJUSTMENT. Manual Crank - Front/Top Mounted Series 3 User Guide HEIGHT ADJUSTMENT Manual Crank - Front/Top Mounted The worksurface adjusts via a simple hand crank. Turn hand crank clockwise to raise the desk and counterclockwise to lower the desk.

More information

200 lb (90.7 kg) 2 People Required. 250 lb (113.4 kg)

200 lb (90.7 kg) 2 People Required. 250 lb (113.4 kg) Weight Capacity 200 lb (90.7 kg) 2 People Required Weight Capacity 250 lb (113.4 kg) 2 People Required x2 x4 x4 For patent and trademark information, visit VARIDESK.com/patents 2018 VARIDESK. All Rights

More information

JLTX Lever and Joystick Replacement Instructions

JLTX Lever and Joystick Replacement Instructions JLTX Lever and Joystick Replacement Instructions WARNING THE INCORRECT INSTALLATION OF A LEVER OR JOYSTICK CAN CAUSE AN EQUIPMENT MALFUNCTION FAILURE TO FOLLOW THIS PROCEDURE CAREFULLY COULD RESULT IN

More information

OV1016 Part No OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM USER GUIDE

OV1016 Part No OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM USER GUIDE OV1016 Part No. 86042 OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM USER GUIDE PRODUCT OVERVIEW User Guide: OV1016 OV1016 HEIGHT ADJUSTABLE BENCHING SYSTEM Our best-selling value table base is now available

More information

Olympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4

Olympus BX43 and BX46 Installation Instruction for Microscope End Users (easy install version) 4 Olympus X and X6 Installation Instruction for Microscope End Users (easy install version) PN 07 Olympus X_6 Illuminator ssy dditional Items Included ut Not Shown: PN 077 Hex Key mm PN 060 Hex Key mm M

More information

CHAPTER 3B: ELECTRONIC POWER STEERING

CHAPTER 3B: ELECTRONIC POWER STEERING Electronic Power Steering CHAPTER 3B: ELECTRONIC POWER STEERING NOTE: The basic steering system, such as the tie rod ends, drag links axles, etc., is covered in Chapter 3A: Steering. In 2012, Cub Cadet

More information

INCLUDED HARDWARE REQUIRED TOOLS GETTING STARTED DISCLAIMERS! 5/32 Allen Wrench (Provided)

INCLUDED HARDWARE REQUIRED TOOLS GETTING STARTED DISCLAIMERS! 5/32 Allen Wrench (Provided) UPSIDE INCLUDED HARDWARE 8 x 5/8 Screw M6x16 REQUIRED TOOLS 5/32 Allen Wrench (Provided) GETTING STARTED Assemble on a soft surface to avoid scratching the worksurface. Hardware & tools required may vary

More information

Quick Installation Guide

Quick Installation Guide Full Motion Single Monitor Arm, Pole Mount Quick Installation Guide Please Review the entire Quick Installation Guide prior to installation. If you have any questions regarding the compatibility of this

More information

Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure

Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure Motion LE1700 Tablet PC Hard Disk Drive Upgrade Procedure 2008 Motion Computing, Inc. All rights reserved. This document contains information protected by copyright. No part of this document may be reproduced

More information

TDM To MiniMech conversion ProceDure

TDM To MiniMech conversion ProceDure TDM To MiniMech conversion ProceDure (Model 9100 ATM) TDN 07102-00079 Apr 1 2009 CorporATe HeAdquArTers: 522 E. Railroad Street Long Beach, MS 39560 PHONE: (228) 868-1317 FAX: (228) 868-0437 COPYRIGHT

More information

Holland Computers, Inc. Crane Kit Manual Part Number RA-CRANE-KIT

Holland Computers, Inc. Crane Kit Manual Part Number RA-CRANE-KIT Holland Computers, Inc. Crane Kit Manual Part Number RA-CRANE-KIT SECTION 1 - Introduction Description This kit has been manufactured as a replacement gantry and electronics for existing machines using

More information

APES-14 HD-6500 & HD-7000 Version Operator s Training Manual

APES-14 HD-6500 & HD-7000 Version Operator s Training Manual APES-14 HD-6500 & HD-7000 Version Operator s Training Manual Issue A1 09/03 PDI Part # 900600 Performance Design Inc. 2350 East Braniff St. Boise Idaho 83716 This manual contains very important safety

More information

Replace the edrive TINI Module and Battery

Replace the edrive TINI Module and Battery Product All edrive Configurations Special Information INFORMATION: This service bulletin is for informational purposes only. It is intended for use by Northrop Grumman Cutting Edge Optronics (NG CEO) employees

More information

KRONOS 6752 LIFT DESK

KRONOS 6752 LIFT DESK KRONOS 6752 OWNER S MANUAL Product Registration Registering your new BDI product allows us to send you important product updates, service information and helpful hints related to your BDI products. Register

More information

Model: MRK-300FD-BK. Aluminum Mobile Rack 3-1

Model: MRK-300FD-BK. Aluminum Mobile Rack 3-1 Model: MRK-300FD-BK Aluminum Mobile Rack 3-1 3-1 Introduction... 3-3 Mobile Rack Features... 3-3 Unpacking Your Mobile Rack... 3-4 IDE Basics... 3-4 3-2 Hardware Installation... 3-5 Mobile Rack Components...

More information

Assembly Instructions

Assembly Instructions Assembly Instructions Flat Screen Garage End User & IT Computer Cable Management May 2013 nylon zip-tie #2 (for computer wires) rear-access beam door (open) Figure 1 nylon zip-tie #1 (for #1 motor control

More information

Solid State Control Calibration Procedure MKG Solid State Griddles - All Options

Solid State Control Calibration Procedure MKG Solid State Griddles - All Options Solid State Control Calibration Procedure MKG Solid State Griddles - All Options The following procedure describes the steps to calibrate the Solid State Temperature Control for any of the MKG-ST Griddle

More information

UPLIFT 2-Leg Height Adjustable Standing Desk (Version v4 Control Box)

UPLIFT 2-Leg Height Adjustable Standing Desk (Version v4 Control Box) UPLIFT 2-Leg Height Adjustable Standing Desk (Version v4 Control Box) DIRECTIONS FOR ASSEMBLY AND USE TABLE OF CONTENTS Also watch our assembly video http://bit.ly/2qvkeuf PAGE 1 Safety and Warnings 2

More information

SQM5 Reversing Actuators, with Multiple Analog Control Input Signals

SQM5 Reversing Actuators, with Multiple Analog Control Input Signals Document No. 9-4 January 8, 8 SQ5 Reversing Actuators, with ultiple Analog Control Input Signals Product Description Reversing actuator used to position flow control valves, butterfly valves, dampers,

More information

PoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery.

PoE/FPR Kit for Auto-Sync Time Clock. The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. ASTCPOEK PoE/FPR Kit for Auto-Sync Time Clock The Auto-Sync Time Clock is a validated time system with a Web interface and auto discovery. The ASTCPOEK Kit provides Power over Ethernet with Full Power

More information

Parts List: Assembly Instructions:

Parts List: Assembly Instructions: My Ride SERVICE MANUAl MyRide ASSEMBLY GUIDE 1.1 ASSEMBLY INSTRUCTIONS ASSEMBLING THE MYRIDE Parts List: Heavy Plate Stabilizer Fin - Right Stabilizer Fin - Left Stabilizer Fin - Large Middle Power Cord

More information

Smith Meter TM Load Printer

Smith Meter TM Load Printer Smith Meter TM Load Printer Issue/Rev. 0.1 (7/03) Service Bulletin MN06011 Contents Section 1 Introduction... Page 2 Section 2 Servicing... Page 3 Tools Required... Page 3 Printer Head Assembly Removal...

More information

Operating Instructions

Operating Instructions Operating Instructions Model Numbers: LS LS M LS G LS A LS LS 00 LS M-WC LS A LS X LS M-WC LS B LS X LS M LS Dimensions A / B / C / D / E 0 / F / Electrical Information Voltage AMPS Frequency 0 HZ Single

More information

Remote Control Electrical Roller Blinds

Remote Control Electrical Roller Blinds Remote Control Electrical Roller Blinds Instruction Manual for Model HT200 Contents 1. Description of Remote Control Electrical Roller Blind General Information Technical Data 2. Parts List Model HT200

More information

Troubleshooting CHAPTER

Troubleshooting CHAPTER CHAPTER 1 1 1 1 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 0 1 1 1 0 1 6 0 1 1 0 1 1 0 1 0 1 10 1 0 1 1 0 1 0 1 1 0 1 0 1 1 0 1 10 Troubleshooting NOTICE: Information in this manual may change without notice.

More information

ATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES

ATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard

More information

Wiring Instructions v4

Wiring Instructions v4 Wiring Instructions v4 GateKeeper h4.2 Technical Support support@gymmastersoftware.com USA: 415 678 1270 Australia: 03 9111 0323 : 03 974 9169 Copyright 2018 Treshna Enterprises. All rights reserved. 15

More information

Phillips Screwdriver. Some C-128's may need a TORX ("star" point) driver (size T10)f available at Sears, and other hardware and automotive stores.

Phillips Screwdriver. Some C-128's may need a TORX (star point) driver (size T10)f available at Sears, and other hardware and automotive stores. C-128 INSTALLATION Required Tools: Phillips Screwdriver. Some C-128's may need a TORX ("star" point) driver (size T10)f available at Sears, and other hardware and automotive stores. IC extractor or small,

More information

Preparing for a Docking Drawer Slim Installation To prepare for a successful Docking Drawer Slim installation please ensure that the cable management

Preparing for a Docking Drawer Slim Installation To prepare for a successful Docking Drawer Slim installation please ensure that the cable management Docking Drawer Install Manual Docking Drawer Slim Series Applicable Models: 0290 00031(W) / 24 0290-00030(W) / 21 0290-00047(W) / 18 0230-00004. r6 1/19/2016 CAUTION READ CAREFULLY Failure to follow these

More information

Phase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin:

Phase Loss Protection Upgrade. Phase Loss Protection Upgrade. In this bulletin: Phase Loss Protection Upgrade In this bulletin: Introduction... 2 Purpose... 2 General... 2 Applicability... 2 HD3070 Phase Loss Protection Upgrade Kit Parts... 2 Preparation... 4 Install the Phase Loss

More information

Moving-Minds.com Treadmill Desk Operation

Moving-Minds.com Treadmill Desk Operation LifeSpan Treadmill Desk - Owner s Manual Models DT-5/DT-7 Desk Assembly DT-5 Desk........................................................................................ Assembly Instructions..........................................................................

More information

S Reclosers Kyle Type VXE Electronic Control SCADA Input/Output Board Installation and Operation Instructions

S Reclosers Kyle Type VXE Electronic Control SCADA Input/Output Board Installation and Operation Instructions Reclosers Kyle Type VXE Electronic Control SCADA Input/Output Board Installation and Operation Instructions Cooper Power Systems Service Information S0-6- Applicable to VXE5 reclosers serial number 006

More information

Keypad Lock. Operation and Service Manual. Order parts online

Keypad Lock. Operation and Service Manual. Order parts online Keypad Lock Order parts online www.follettice.com Operation and Service Manual 801 Church Lane Easton, PA 18040, USA Toll free (800) 523-9361 (610) 252-7301 Fax (610) 250-0696 www.follettice.com 00163345R00

More information

Part Number: Lt. Taupe / Stone / Ivory Touring Edition Accessory Code: EH3

Part Number: Lt. Taupe / Stone / Ivory Touring Edition Accessory Code: EH3 Part Number: Lt. Taupe - 00016-00710 / Stone - 00016-00720 / Ivory - 00016-00730 Touring Edition - 00016-00745 Accessory Code: EH3 Kit Contents Item # Quantity Reqd. Description 1 2 Headrest Assembly 2

More information

Wiring Instructions v3

Wiring Instructions v3 Wiring Instructions v3 Gatekeeper h4.1 Technical Support support@gymmastersoftware.com USA: 415 678 1270 Australia: 03 9111 0323 : 03 974 9169 Copyright 2017 Treshna Enterprises. All rights reserved. Table

More information

Modem Installation and Networking Instructions

Modem Installation and Networking Instructions Modem Installation and Networking Instructions P/N 36870 Rev F Introduction The following instructions cover connecting a phone line to an incoming phone source, installing a modem, and setting up a network

More information

Control Box Setup - PRSalpha

Control Box Setup - PRSalpha 888-680-4466 ShopBotTools.com Control Box Setup - PRSalpha Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Parts List: Hooking Up a PRSalpha Gantry Tool Powering the

More information

Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443

Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443 Thanks for shopping with Improvements! Lighted Canterbury Christmas Greenery Doorway Arch Item #548443 IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY. PARTS LIST: 2 Metal Plate Stands 5 Greenery

More information

Quick Installation Guide

Quick Installation Guide Full Motion Dual Monitor Arm, Pole Mount Quick Installation Guide Please Review the entire Quick Installation Guide prior to installation. If you have any questions regarding the compatibility of this

More information

V.I.A. - Monitor Shroud

V.I.A. - Monitor Shroud V.I.A. - Monitor Shroud NOTE: Installing slatwall above a monitor shroud requires modification of the upper horizontal rail. See V.I.A. Slatwall assembly direction 939502328 for installation process. V.I.A.

More information

Back Tilt Sensor Repair Kit [ ]

Back Tilt Sensor Repair Kit [ ] Back Tilt Sensor Repair Kit [002-1377-00] Components: Potted Tilt Sensor & Harness...1 Cable Ties...8 Step 1: Position chair. A) Press chair up control button to raise chair seat approximately 26-28 above

More information

Cycles Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions

Cycles Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions Recumbent Upright Cycles Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 4 Obtaining Service... 4 Unpacking the

More information

TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION

TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION S6 USER S MANUAL TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION SECTION 4 SLIDE CONFIGURATION ACCESSORIES SECTION 5 RACK MOUNT

More information

C-pan arm USERS INSTRUCTIONS

C-pan arm USERS INSTRUCTIONS C-pan arm USERS INSTRUCTIONS Designed 1 of 12 and made in Denmark Thanks for purchasing a 9.Solutions product. With great passion, we design our products to be as versatile as possible. We hope that our

More information

Measure Ø-N, Ø-Ø, Ø-Gnd with voltmeter to confirm application voltage prior to installation.

Measure Ø-N, Ø-Ø, Ø-Gnd with voltmeter to confirm application voltage prior to installation. Product No. 99-600-91 Rev. B Page 1 of 8 MCG Surge Protection Model 160MXT Installation Instructions Important Warranty Information MCG surge protectors are designed to work at specific voltages and configurations,

More information

REMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer.

REMOVE COVERS. 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. REMOVE COVERS 1. Remove three screws from the Side Panel (L). 2. Slide the Side Panel (L) backward, and raise it to remove from the printer. 3. Fully open the Top Cover. 4. Release the tab on the right

More information

21 TRACK MAINTENANCE GUIDE

21 TRACK MAINTENANCE GUIDE Mountain Engineering II, Inc. 21 TRACK MAINTENANCE GUIDE 1233 Sherman Drive, Longmont, CO 80501-6133 303-651-0277 303-651-6371 (fax) www.mountainengineering.com Table of contents Table of contents...2

More information

Packard Bell. EasyNote BU Series. Disassembly Guide

Packard Bell. EasyNote BU Series. Disassembly Guide Packard Bell EasyNote BU Series Disassembly Guide Table of Contents Overview...3 Technician Notes...3 Disassembly Instructions...3 Reassembly Instructions...3 Required Tools...3 Battery...4 Memory...4

More information

G12/G12x USER S MANUAL

G12/G12x USER S MANUAL G12/G12x USER S MANUAL TABLE OF CONTENTS SECTION 1 SLIDE CONFIGURATION SECTION 2 SLIDE CONFIGURATION ACCESSORIES SECTION 3 TABLETOP CONFIGURATION SECTION 4 TABLETOP CONFIGURATION ACCESSORIES SECTION 5

More information

APPLICATION PROCEDURE HOUSING INSTALLATION AND EQUIPMENT LOCATION

APPLICATION PROCEDURE HOUSING INSTALLATION AND EQUIPMENT LOCATION NH208TVU Amplifier and Power Supply Installation and Use Instructions Used with the HT2006 Series Inside Handset Intercom Stations and 1 or more Door Stations APPLICATION The NH208TVU series intercom system

More information

TURN-O-MATIC INSTALLATION GUIDE

TURN-O-MATIC INSTALLATION GUIDE TURN-O-MATIC INSTALLATION GUIDE WIRELESS SYSTEM WIRELESS SYSTEM (1) Dispenser (1) Dispenser Mounting Bracket (3) Large Slotted Screw (2) Large Slotted Bolt (2) Nut (1) Display Wall Mount Bracket (1) Wireless

More information

Olympus BX43_46 Installation Instruction (OEM Adjust) 4

Olympus BX43_46 Installation Instruction (OEM Adjust) 4 Olympus X_6 Installation Instruction (OEM djust) If you are not an experienced repair tech please consider the alternate (easy install) version dditional Items Included ut Not Shown: PN 07 Olympus X Illuminator

More information

edrive RAM Battery Alternate Replacement Procedure

edrive RAM Battery Alternate Replacement Procedure edrive RAM Battery Summary This technical note describes the process for replacing the TINI RAM battery with a higher capacity battery. With the edrive turned on, the external battery can be changed without

More information

Bluetooth Shielding Instructions

Bluetooth Shielding Instructions Mac mini 2012 Bluetooth Shielding Instructions 1 INTRODUCTION 1.1 STATIC PRECAUTIONS 1.2 TOOLS REQUIRED 2 DISASSEMBLY 3 SHIELDING 4 FAQ 4.1 FAQ 5 CUSTOMER SERVICE 5.1 Before Contacting Customer Service

More information

PRODUCT MARKING AND BARCODE IDENTIFICATION. up to Serial No Barcode/Label printer MACH4. Service Manual. Edition 11/06

PRODUCT MARKING AND BARCODE IDENTIFICATION. up to Serial No Barcode/Label printer MACH4. Service Manual. Edition 11/06 PRODUCT MARKING AND BARCODE IDENTIFICATION up to Serial No. 9999 Barcode/Label printer MACH4 Service Manual Edition 11/06 copyright by cab / 9008553 / Q49 / 1 All specifications about delivery, design,

More information

SAVE THESE INSTRUCTIONS

SAVE THESE INSTRUCTIONS and Height Mounts Assembly, Installation and Operating Instructions Model Nos. QL, QLA, ARM250, QLM6 and QLAM6 NOTE: Check all parts for shipping damage. In case of shipping damage, DO NOT use. Contact

More information

TRC-190 User s Manual

TRC-190 User s Manual First Edition, November 2008 www.moxa.com/product 2008 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. The software described in this manual is furnished under a license agreement

More information

Choices Height Adjustable Tables ELECTRIC TABLES

Choices Height Adjustable Tables ELECTRIC TABLES Choices Height Adjustable Tables ELECTRIC TABLES INSTALLATION INSTRUCTIONS TOOLS REQUIRED: Metric Allen wrenches #2 Phillips driver ATTENTION! The control boxes and electric motors must be synchronized

More information

9109 FXS Analog Voice Application Module (APM) Installation Instructions. Product Documentation on the World Wide Web

9109 FXS Analog Voice Application Module (APM) Installation Instructions. Product Documentation on the World Wide Web TM 9109 FXS Analog Voice Application Module (APM) Installation Instructions Document Number 9109-A2-GN12-40 May 1999 Product Documentation on the World Wide Web We provide complete product documentation

More information

A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE

A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE A-dec 570L Dental Light on a DCS System INSTALLATION GUIDE C ONTENTS Choose an Installation Guide...... Before You Begin.............. 3 Disconnect the Light Cable........ 3 Cut the Light Cable............

More information

( GRAY CONTROL BOX )

( GRAY CONTROL BOX ) DC LEISURE PRO SHORE COMMANDER Troubleshooting Guide ( GRAY CONTROL BOX ) INDEX 1.0 Power recommendations 1.1 System does not work at all when plugged in 1.2 System has power but No touchpad function or

More information

LENS REPLACEMENT PROCEDURE

LENS REPLACEMENT PROCEDURE LCD PROJECTOR LENS MODEL LNS-T31A/W31A LENS REPLACEMENT PROCEDURE NOTE; Lens installation is different in cabinet design (Type A and B). Before installation the lens, check cabinet design and proper installation

More information

UPLIFT 3-Leg Desk Instructions for. Solid Wood Desktops. (Version v4 Control Box) pictured: Solid-wood top with right hand return TABLE OF CONTENTS

UPLIFT 3-Leg Desk Instructions for. Solid Wood Desktops. (Version v4 Control Box) pictured: Solid-wood top with right hand return TABLE OF CONTENTS UPLIFT 3-Leg Desk Instructions for Solid Wood Desktops (Version v4 Control Box) pictured: Solid-wood top with right hand return TABLE OF CONTENTS PAGE 1 Safety and Warnings 2 2 Usage 2 3 Parts List 3 4

More information

Network Controller. Installation/Troubleshooting Instructions NK220 COM1131C

Network Controller. Installation/Troubleshooting Instructions NK220 COM1131C Network Controller NK220 COM1131C Installation/Troubleshooting Instructions Part No. 70399101R4 October 2009 Table of Contents Getting Started... 2 Components of Network Controller... 2 System Overview...

More information

EH50 ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF

EH50 ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF Toyota 4Runner 2011 - Dual Player Headrest Video Part Number: 00016-00360; Sand Beige 00016-00370; Black Accessory Code: EH50 ATTENTION: SECURITY COVERS ARE NO LONGER INCLUDED IN THE HEADREST KITS AS OF

More information

Addendum to the Actalyst Interactive Digital Signage Installation and User s Guide

Addendum to the Actalyst Interactive Digital Signage Installation and User s Guide Addendum to the Actalyst Interactive Digital Signage Installation and User s Guide This addendum contains information about the Actalyst Interactive Overlay that has changed since the release of the Actalyst

More information

2 in 1 LAN Tester and Multimeter Model:

2 in 1 LAN Tester and Multimeter Model: 2 in 1 LAN Tester and Multimeter Model: 72-8495 1 IMPORTANT SAFETY INFORMATION Please read these instructions carefully before use and retain for future reference. This instrument is designed and manufactured

More information

Upgrading and Servicing Guide

Upgrading and Servicing Guide Upgrading and Servicing Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed

More information

REMOTE CONTROLLED HEAD. User Manual. pdf version of the manual available for download: 9/2016

REMOTE CONTROLLED HEAD. User Manual. pdf version of the manual available for download:   9/2016 REMOTE CONTROLLED HEAD 9/016 User Manual pdf version of the manual available for download: www.slidekamera.com Before you start your work with Slidekamera BULL HEAD remote controlled head we strongly recommend

More information

Navigator II INstallatIoN MaNUal For static and PaN/tIlt configurations

Navigator II INstallatIoN MaNUal For static and PaN/tIlt configurations Navigator II Installation MANUAL For Static and Pan/Tilt Configurations Document Number: 432-0001-00-12, rev 100 FLIR Systems, Inc., 2008. All rights reserved worldwide. No parts of this manual, in whole

More information

Cutter Option Installation Instructions

Cutter Option Installation Instructions This kit includes the parts and documentation necessary to install the cutter option on the Zebra XiII, XiIII, and XiIIIPlus-Series printers. NOTE: The Cutter Option is not available for the 96XiIII. Adding

More information

TRC-190 User s Manual

TRC-190 User s Manual User s Manual Edition 3.2, May 2017 www.moxa.com/product 2017 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used only

More information

Oracle <Insert Picture Here>

Oracle <Insert Picture Here> Slide 1 Oracle Slide 2 WZT-6509 version B Sun Fire Nehalem and Westmere Rack-Mount Server Installation and Replacement Welcome to the installation and replacement

More information

Eaton LCD Lift Flat Panel Display System. Installation Guide

Eaton LCD Lift Flat Panel Display System. Installation Guide Eaton LCD Lift Flat Panel Display System Eaton LCD Lift Flat Panel Display System Installation Guide Copyright 2011 Eaton Corporation, Worcester, MA, USA. All rights reserved. Information in this document

More information

WEASEL N/B MAINTENANCE

WEASEL N/B MAINTENANCE 2. System Assembly & Disassembly 2.1 System View 2.1.1 Front View ❶ Microphone Connector ❷ Audio Input Connector ❸ Audio Output Connector ❹ Top Cover Latch ❹ ❶ ❸ ❷ 2.1.2 Left-Side View ❶ VGA Port ❷ S-Video

More information

INSTRUCTION BULLETIN

INSTRUCTION BULLETIN INSTRUCTION BULLETIN No. 9008755 Machine: T16 Published: 03-2011 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine

More information

ColorMaxLP Label Roll Rewinder

ColorMaxLP Label Roll Rewinder ColorMaxLP Label Roll Rewinder 5/2017 INSTALLATION/OPERATOR MANUAL Included: Rewinder Base plate Power supply Power Cord Thumb screws Assembly instructions 1. Install base plate Lift front of printer and

More information

UPLIFT 4-Leg Height Adjustable Standing Desk (Version v4.1 Control Box)

UPLIFT 4-Leg Height Adjustable Standing Desk (Version v4.1 Control Box) UPLIFT -Leg Height Adjustable Standing Desk (Version v. Control Box) DIRECTIONS FOR ASSEMBLY AND USE TABLE OF CONTENTS PAGE Safety and Warnings 2 2 Usage 2 3 Parts List 3 Assembly Instructions 5 Desk Placement

More information

Hard Drive user manual

Hard Drive user manual Hard Drive Docking Kit user manual Model 450096 MAN-450096-UM-1007-02 introduction Thank you for purchasing the MANHATTAN Hard Drive Docking Kit, Model 450096. The easy-to-follow instructions in this user

More information

EPROM REPLACEMENT INSTRUCTIONS

EPROM REPLACEMENT INSTRUCTIONS MOTION CONTROL ENGINEERING, INC. 11354 WHITE ROCK ROAD RANCHO CORDOVA, CA 95742 TELEPHONE (916) 463-9200 FAX (916) 463-9201 CAR CONTROLLER MAIN PROCESSOR BOARD EPROM REPLACEMENT INSTRUCTIONS 42-02-G002

More information

E1135C PDU and Pod Upgrade Procedure

E1135C PDU and Pod Upgrade Procedure E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support

More information

PIX 515/515E. PIX 515/515E Product Overview CHAPTER

PIX 515/515E. PIX 515/515E Product Overview CHAPTER CHAPTER 4 PIX 515/515E This chapter describes how to install the PIX 515/515E, and includes the following sections: PIX 515/515E Product Overview Installing a PIX 515/515E PIX 515/515E Feature Licenses

More information

Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options

Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options CHAPTER 4 Installing the Cisco ADE 2130 and 2140 Series Appliance Hardware Options This chapter provides instructions for installing, replacing, and removing various hardware options in your Cisco ADE

More information