Metropolis ADM MultiService Mux Compact Shelf

Transcription

1 Metropolis ADM MultiService Mux Compact Shelf Engineering and Ordering Information Release 5.0 ED8C Issue 5 13-May-2005 AN55 Copyright 2005 Lucent Technologies All Rights Reserved A A

2 About This Drawing This document provides application engineering details and ordering codes for Metropolis ADM MultiService MUX. Specifications and application considerations are included to properly engineer the network element for desired functionality, as well as condition the location for proper operation and maintenance. The most current Issue of this drawing can be obtained in paper format or electronically downloaded from the Lucent Corporate Information Center (CIC) by specifying the drawing number. The CIC website is accessed by non-lucent employees at In addition, comments or questions concerning the document content should be directed through a Lucent Account Representative. For Lucent employees, the CIC website is accessed at Comments or questions can be directed to a SME identified via: Associated References Application and Planning Guide User Operations Guide Alarm and Trouble Clearing Guide Installation Guide Part Installation Guide Part Provisioning Guide ED8C Interconnect Information Reason for Re-issue Issue Original Issue Issue Release 3.3 Update Issue Release 4.0 Added Software Ordering Table Issue Release 4.0 Update Added PDP-M Kits Issue Release 5.0 Added prefabricated cable assemblies ED8C Issue 5 A2

3 Table of Contents Description of Sheet Sheet Number Updated This Issue Title Sheet A1 * About This Drawing A2 * Reason for Re-issue A2 * Table of Contents A3 Engineering Notes A4 * Table A - Equipment Kits and Assemblies B1 Table B - Orderable Circuit Packs B2 * Table C- Paddle Boards B3 Table D - Line Build Outs (LBO) B3 * Table E - Cable Assemblies and Cable Kits B4 * Table F - Software Ordering Table B6 * Floor Plan Data C1 Figure 1 - ETSI 2200mm Rack Dimensions D1 Figure 2 - ETSI 2600mm Rack Dimensions D2 Figure 3 -Slot Identification D3 Figure 4 - Subrack Interconnect Interface D4 Figure 5 - Subrack Interface Dimensions for 19 Rack Mounting D5 Figure 6 - Subrack Interface Dimensions for ETSI Rack Mounting D6 Figure 7 - PDP-M Interface Dimensions D7 Figure 8 - PDP-MA D8 Figure 9 - Circuit Pack Faceplate SFP Interface LKA12 D9 Figure 10 - Patch Panel Kit D10 Figure 11 - E1 (2 Mbit/s) Paddle Boards and Patch Panel Interface D11 Figure 12 - Other Paddle Board Interfaces D12 Total Sheets 23 ED8C Issue 5 A3

4 Engineering Notes 1. For Lucent Engineered orders, job information shall be recorded by comcode number in the regional wiring lists. 2. The High Density Subrack (EHA1) includes mounting brackets for both ETSI Rack and 19" Rack installation. 3. Quick Copy block (QCB) kit comcodes listed are for the raw cable only. Order the QCB to receive all associated hardware to assemble the cable or kit. 4. If a PI- EI/63 unit is inserted in slot 7, it is in the protection unit and may not be used to carry traffic. 5. If LKA5 is inserted in Slots 1 and 2, only a 2Mbit/s Tributary interface unit (LKA2) is allowed in Slot The 2Mbit/s Paddle Boards extend below the bottom of the subrack when installed. This extends the overall height of the subrack to 925mm. Be sure to allow enough space below the subrack for installation or if future 2Mbit/ paddle boards will be required. 7. The Cable and Connector Kit provides the following: 1 MD 1 Connector Kit 15P DSUB Male Connector, Hood and Ferrules 1 Station Alarm Kit 15P DSUB Male Connector, Hood and Ferrules 2 V11 Connector Kits 15P DSUB Male Connector, Hood and Ferrules 1 MD 2 Connector Kit 9P DSUB Male Connector, Hood and Ferrules 1 Q-Lan Connector Kit 9P DSUB Male Connector, Hood and Ferrules 2 G703 Connector Kits 9P DSUB Male Connector, Hood and Ferrules 2 Station Clock IN Connector Kits 9P DSUB Female Connector, Hood and Ferrules 2 Station Clock OUT Connector Kits 9P DSUB Male Connector, Hood and Ferrules 8. The Patch Panel kit is used when conversion from SC to FC interfaces are required for the optical tributaries. One Patch Panel kit is required for every LKA6 or LKA13 requiring this interface. Only one Patch Panel Kit is required for two of either LKA11 or LKA14 Circuit Packs. 9. Slot 7 is reserved for 1:N Protection when using electrical 2 Mbit/s or STM-1 tributary units. It can also be used for unprotected STM-1 optical interfaces (only in combination with core unit LKA5B). TransLAN units are not allowed in Slot The Patch Panel Kit can accommodate a maximum of 8 optical interfaces. An additional connector strip and cable kit increases the optical interfaces to The PDP-M Kit Supports 2 Subracks. If connecting more Subracks to the PDP-M, additional alarm cables must be ordered. The kit contains: 1 PDP-M 1 PDP-MA 1 1.6M (5.25 Ft) Alarm Cable (Upper Subrack) 1 3.2M (10.5 Ft) Alarm Cable (Lower Subrack) 12. The PDP-M Power Kit is required when ordering a PDP-M or PDP-M Kit. It Contains 2 Circuit Breakers (16A) and 2 Power Cables. One PDP-M power kit is required for each Subrack. 13. A Maximum of two subracks may be installed in a 300mm deep bay. 14. The LKA12B Circuit Pack may be used with release 4.0 software only for the Quality of Service (QOS) feature. Previous releases must use LKA12. ED8C Issue 5 A4

5 Features B Table A - Equipment Kits and Assemblies Description Comcode Figures Notes MADM (ETSI) Rack, 2200 mm DA MADM (ETSI) Rack, 2600 mm DA MADM (ETSI) Rack, 2200 mm MADM (ETSI) Rack, 2600 mm High Density Subrack Kit Contains subrack (EHA1) and mounting Hardware ,4,5,6 13 High Density Subrack (EHA1) ,4,5,6 DA Patch Panel Kit and Cables ,10 Patch Panel Connector Strip (Additional) Patch Panel Cable Kit (Additional) PDP-M Kit PDP-M Power Distribution Panel PDP-MA Alarm Interface PDP-M Power Kit Circuit Breaker 16 Amp ED8C Issue 5 B1

6 Features Table B - Orderable Circuit Packs Description Comcode Slot Notes Core Packs LKA1D, (SCI) SYSTEM CONTROLLER PLUS, 48 V, 1 UN, LKA5B, SI-L16.1C1/1 (RUBY) CROSS CONNECT ,2 LKA10, SI-L16.2C1/1 CROSS CONNECT ,2 LKA15, CC/PT 64/32 CROSS CONNECT ,2 LKA42, 2X STM-4 L um CC/PT 64/32 LONG HAUL ,2 LKA44, 2X STM-4 S um CC/PT 64/32 SHORT HAUL ,2 STM-4, STM-1 Optical Tributary Port Units LKA11, (SI-S4.1/1) 1.3 um STM ,4,5,6,7 1 Port LKA14, (SI-L4.2/1) LONG HAUL, 1.5 um STM ,4,5,6,7 1 Port LKA6, (SI-S1.1/4) 1.3 um STM ,4,5,6,7 4 Port LKA13, (SI-LI.2/4) LONG HAUL 1.5 um STM ,4,5,6,7 4 Port Electrical Tributary Circuit Packs LKA2, (PI-E1/63) 2 Mbit/s ,4,5,6,7 LKA8B, (PI-E3DS3/12) 34/45 Mbit/s ,4,5,6 LKA3, (SI-1/4) 155Mbit/s ,4,5,6 LKA4, (IP-LAN/8) 10/100Mbit/s ,4,5,6 LKA16, (PI/DS1/63) ,4,5,6,7 Other Circuit Packs and SFP (Small Form Factor Pluggable) LKA12, (IP-GE/2) 1000Base-SX/LX Lan Interface ,4,5,6,7 LKA12B, (IP-GE/2) 1000Base-SX/LX Lan Interface with QOS ,4,5,6,7 14 OMGBE-SX SX Gigabit Ethernet Module (SFP) See Fig 9 2 per OMGBE-LX LX Gigabit Ethernet Module (SFP) See Fig 9 LKA12 or LKA12B ED8C Issue 5 B2

7 Features Table C- Paddle Boards Description Code Use With Pack Notes PBE1-25 Pin D-Sub Connectors (75 Ohm) LKA2 Figure 11 PBE2-25 Pin D-Sub Connectors (120 Ohm) LKA2 Note 6 PBE4 - Field IO Connectors (75 Ohm) LKA2 2 Mbit/s (E1) PBE4 - Field IO Connectors (120 Ohm) LKA2 Figure 11 PBP7-15 pin D-Sub Connectors (75 Ohm) LKA2 34 and 45 Mbit/s (E3/DS3) 155 Mbit/s (STM-1e) PBG4 (unprotected) 1.6/5.6 connectors LKA8 PBG5 (protected) 1.6/5.6 connectors LKA8 PBG2 (unprotected) 1.6/5.6 connectors LKA3 PBG3 (protected) 1.6/5.6 connectors LKA3 10 or 100 Mbit/s PBG1, IP-FE/8 PB-LAN/100/ LKA4 P1-DS1/63 PBE12 - Field IO Connectors (100 Ohm) LKA16 Figure 12 Table D - Line Build Outs (LBO) Description Code Use with Universal Build Out Block (UBOB) Use with SC connectors STM1 and STM 4 SC Type Connector 0 DB A SC Type Connector 10 DB A3060D FC Type Connector 0 DB A FC Type Connector 10 DB A3080D SC Buildout 0.5 DB ABSCS SC Buildout 5 DB ABSCS SC Buildout 10 DB ABSCS ED8C Issue 5 B3

8 Features Table E - Cable Assemblies and Cable Kits Description Note Comcode Fiber Optic Cable Single Mode SC to SC 10.7 Meters (35 Feet) Single Mode SC to SC 22.9 Meters (75 Feet) Single Mode FC to PC 22.9 Meters (75 Feet) Single Mode FC to PC 20 Meters (65.6 Feet) Single Mode SC to FC 20 Meters (65.6 Feet) Electrical Cable Assemblies Power Cables Subrack to PDP-M ( 2 Included with PDP-M Power Kit) 3 Meters (9.8 Feet) Rack Alarm Cable Upper Subrack ( 1 Included with PDP-M Kit) 1.6 Meters (5.25 Feet) Rack Alarm Cable Lower Subrack ( 1 Included with PDP-M Kit) 3.2Meters (10.5 Feet) E1(2Mbit/s) 25 Pin Dsub to Open End (120 Ohm) 30 Meters (98.4 Feet) E1 (2 Mbit/s) Field IO Cables 8 way Coax (75 Ohm) E1 (2 Mbit/s) STP Field IO Cables 8 way STP (120 Ohm) Without Overall Shield E1 (2 Mbit/s) UTP Field IO Cables 8 way UTP (120 Ohm) With Aluminum Foil and Copper Braid Shield DS1 (1.5 Mbit/s) Field IO Cables 8 way STP (100 Ohm) E3/DS3 1.6/5.6 Angle Connector Single Coax Cables (75 Ohm) 8 Meters (26.2 Feet) Meters (39.4 Feet) Meters (49.2 Feet) Meters (72.1 Feet) Meters (98.4 Feet) Meters (164.0 Feet) Meters (227.7 Feet) Meters (26.2 Feet) Meters (39.4 Feet) Meters (49.2 Feet) Meters (72.1 Feet) Meters (98.4 Feet) Meters (164.0 Feet) Meters (227.7 Feet) Meters (26.2 Feet) Meters (39.4 Feet) Meters (49.2 Feet) Meters (72.1 Feet) Meters (98.4 Feet) Meters (164.0 Feet) Meters (227.7 Feet) Meters (328.0 Feet) Meters (26.2 Feet) Meters (49.2 Feet) Meters (72.1 Feet) Meters (98.4 Feet) Meters (164.0 Feet) Meters (6.6 Feet) Meters (16.4 Feet) Meters (32.8 Feet) Meters (49.2 Feet) Meters (65.6 Feet) ED8C Issue 5 B4

9 Table E - Cable Assemblies and Cable Kits (Continued) Description Note Comcode E3/DS3 1.6/5.6 Angle Connector 8-Fold Coax Cables (75 Ohm) 2 Meters (6.6 Feet) Meters (16.4 Feet) Meters (32.8 Feet) Meters (49.2 Feet) Meters (65.6 Feet) Cable (For building custom length) CIT Cable 200 Meters (656 Feet) Station Clock Cable (1 Pair) 200 Meters (656 Feet) G.703 Interface Cable (2 Pair) 500 Meters (1640 Feet) Cat 5 Cable (4 Pair 26 AWG) 500 Meters (1640 Feet) Q-LAN Cable (4 Pair UTP Shielded) 500 Meters (1640 Feet) Connector and Cable Kits Connector Kit 2MB Field IO Connectors For Coax Cable 1 Piece Connector Kit 2MB Field IO Connectors For STP Cable 1 Piece Crimping Tool for 2MB Field IO Connectors (Coax or STP) Connector Kit 2MB 75/120 Ohm (25 Pin D-Sub) 16 Pieces Connector Kit E3/DS3 75 Ohm (1.6/5.6) 24 Pieces Connector Kit STM-1 (1.6/5.6) 8 Pieces Connector Kit LAN (RJ-45) 8 Pieces Cable and Connector Kit (Subrack Interface Cables) DA Cable and Connector Kit (Subrack Interface Cables) See Note Quick Copy Block kits (See Note 3) 6 MM2 Red QCB MM2 Blue 15 Meters Rack Power Cables 10 MM2 Red QCB MM2 Blue 25 Meters MM2 Red QCB MM2 Blue 35 Meters Rack Ground Cable 35 MM2 Green/Yellow QCB Concrete Floor Connection Kit - Expanding Bolts M8 QCB-6705 Raised Floor Connection Kit - Hex Bolts M10 QCB-6706 Fiber Duct Kit - Orange and Black Conduit QCB-6707 ED8C Issue 5 B5

10 System Software CIT Interface Software Table F - Software Ordering Table Description Code Release CD Rom Downloadable Release 3.1 CD Rom Downloadable Release CD Rom Downloadable Release CD-Rom Downloadable Release 4.0 Earth CD-Rom Downloadable Release 5.0 Mars CD-Rom Downloadable Release 9.14 Pearl Use with Release Release Garnet Use with Release 3.1, 3.2, 3.3 Release Mercury Release Venus Use with Release 3.1, 3.2.1, Release Earth M5 Use With Release Release Earth M2 Use With Release ED8C Issue 5 B6

11 Floor Plan Data - Metropolis ADM MultiService Mux (Compact Shelf) Description Power Consumption Value 204W (MAX) 600 [23.62] Operating Voltage Range Subrack Weight (With Circuit Packs, Paddle Boards and Cables) Operating Temperature -48 to -60 VDC 70 Kg (154 LBS) -5C to 45C 300 [11.81] Storage Temperature -25C to 55C 550 [21.65] Transport Temperature -40C to 70C Hole Locations for Anchors Mounting Details for 300mm Racks 750mm REAR AISLE 750 FRONT AISLE TYPICAL BAY FRAME LAYOUT FOR CENTRAL OFFICE TOP VIEW ED8C Issue 5 C1

12 D Figure 1 - ETSI 2200mm Rack Dimensions Rack Alarm Assembly 600 [23.62] 300 [11.81] 2200 [86.61] ED8C Issue 5 D1

13 Figure 2 - ETSI 2600mm Rack Dimensions Rack Alarm Assembly 400 [15.75] 600 [23.62] 300 [11.81] 2200 [86.61] ED8C Issue 5 D2

14 Figure 3 -Slot Identification Core 1 Core 2 TS1 TS2 TS3 TS4 TS5 SC Slot PB1 PB2 PB3 PB4 ED8C Issue 5 D3

15 Figure 4 - Subrack Interconnect Interface View A Power 1 2 OUT 1 IN 1 OUT 2 IN 2 FAN MD 1 STAT ALM V11-1 G703-1 G703-2 Q-LAN CITF STAT CLOCK BTALM MD 2 V11-2 SEEPROM ED8C Issue 5 D4

16 Figure 5 - Subrack Interface Dimensions for 19 Rack Mounting [19.0] [10.4] 16.7 [0.7] 27.8 [1.1] [9.6] [24.6] 335 [13.2] [11.0] ED8C Issue 5 D5

17 Figure 6 - Subrack Interface Dimensions for ETSI Rack Mounting 535 [21.1] [10.4] 515 [20.3] 16.7 [0.7] 18.5 [0.7] 20.8 [0.8] 10.1 [0.4] [10.0] [24.6] 335 [13.2] [10.1] ED8C Issue 5 D6

18 Figure 7 - PDP-M Interface Dimensions [18.83] [18.31] ETSI Mounting Bracket Mounting Holes For ETSI-2 Mounting GROUNDING THREADS 25.0 [0.98] 40.3 [1.59] 97.6 [3.84] [22.28] [21.15] [4.54] ED8C Issue 5 D7

19 Figure 8 - PDP-MA PDP-MA Mounted on top of PDP-M 4-pin locking connectors 6 places 62.4 [2.5] 67.5 [2.7] Left View 28.5 [1.1] [4.9] Top View ED8C Issue 5 D8

20 Figure 9 - Circuit Pack Faceplate SFP Interface LKA12 Remove dust caps insert SFP Modules RX1 TX1 RX2 TX2 LKA12 ED8C Issue 5 D9

21 Figure 10 - Patch Panel Kit [4.44] 7.5 [0.30] 7.4 [0.29] Patch Panel Cable Kit Patch Panel Connector Strip 189 [7.44] Fiber optic cable SC to SC 1.3 Meters Long (8) 59 [2.32] 15 [0.59] SC to FC Adapter (8) 23.5 [0.93] ED8C Issue 5 D10

22 Figure 11 - E1 (2 Mbit/s) Paddle Boards and Patch Panel Interface 925 [36.4] PBE3 PBE4 Field IO (16) PBP7 15 Pin D-Sub (16) Patch Panel PBE1 PBE2 25 Pin D-Sub (16) ED8C Issue 5 D11

23 Figure 12 - Other Paddle Board Interfaces PBG3 1.6/5.6 (8) PBG5 1.6/5.6 (24) PBE12 Field IO (16) PBG1 RJ-45 (8) PBG2 1.6/5.6 (8) PBG4 1.6/5.6 (24) Protected Configuration ED8C Issue 5 D12