ANT CNTR DC ALRM LNB RX DC ALRM +18V OFF

Transcription

1 Instruction Manual Model Power Supply July 2012, Rev. B MODEL 2082 POWER SUPPLY CROSS TECHNOLOGIES INC. PRIMARY PWR AC BUC +48V AUX BUC TX SELECT 48V +18V/48V LNB RX +18V ANT CNTR +29V AC 18V Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc. for purposes of operating the equipment. When ordering parts from Cross Technologies, Inc., be sure to include the equipment model number, equipment serial number, and a description of the part. CROSS TECHNOLOGIES, INC Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free WEB: info@crosstechnologies.com

2 INSTRUCTI MANUAL MODEL Power Supply TABLE OF CTENTS PAGE Warranty General Equipment Description Technical Characteristics Installation Mechanical Rear Inputs, Outputs and Indicators Front Controls and Indicators Operation Environmental Use Information 10 WARRANTY - The following warranty applies to all Cross Technologies, Inc. products. All Cross Technologies, Inc. products are warranted against defective materials and workmanship for a period of one year after shipment to customer. Cross Technologies, Inc. s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc. s option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall not be liable for any special, indirect, or consequential damages. This warranty does not cover parts or equipment which have been subject to misuse, negligence, or accident by the customer during use. All shipping costs for warranty repairs will be prepaid by the customer. There are not other warranties, express or implied, except as stated herein. CROSS TECHNOLOGIES, INC Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free WEB info@crosstechnologies.com Manual_Rev.B Page 2 07/26/12

3 MODEL Power Supply 1.0 General 1.1 Equipment Description The Power Supply is a voltage Power Supply used for BUC and LNB applications. Power is inserted via two L-Band loop-throughs and a +48 V, 8A output is provided on the BUC output. The two L-Band loop-throughs insertion, a +18V, 1A output is provided on the Antenna LNB input and either 3A or 5A is provided on the Antenna AUX BUC TX output. The unit facilitates the installation of a TracStar Antenna Controller and provides the +29V 150W needed with all of the TracStar connectors accessible through the rear panel. Front panel locking toggle switches allow the user to independently disable the power on either L-Band loop-through, the BUC output and the TracStar antenna controller. The AUX BUC TX and BUC output are interlocked to prevent both outputs from being simultaneously enabled. The user is also able to select +18V or +48V insertion on the AUX BUC TX loop-through. A 500mA AUX output is provided for user devices. Primary power is either 19-72V or VAC. If both primary power sources are connected the user can select which will be enabled and the other source will be put in a standby mode and serve as a backup power source. If only one primary source is connected, the Power Supply will use the available power source regardless of the selected primary power source switch position. Each power source is fused using rear panel mount fuse holders. Front panel LEDs indicate AC or primary power (green), and Standby (yellow). output indications are provided for all four outputs (three outputs and the TracStar antenna controller). Front panel LEDs (green) and rear panel LEDs (yellow) indicate the presence of voltage on LNB, BUC, Aux BUC and the TracStar. Front panel LEDs (yellow) indicate the output is in a Standby condition. Front panel LEDs (red) indicate an Alarm condition which is the result of a blown or missing fuse. The alarm condition will only occur if the output is enabled. Front panel test points are provided for each of the four output voltages and ground. All loop-through connectors are TNC female. The unit is housed in a RU x 3.50 High x Deep chassis. MODEL 2082 POWER SUPPLY CROSS TECHNOLOGIES INC. PRIMARY PWR AC BUC +48V AUX BUC TX SELECT 48V +18V/48V LNB RX +18V ANT CNTR +29V AC 18V FRT PANEL AUX +48V 1/2 AMP MAX ANT MOD PC ICC BUC +48 V 8A MAX V IN 60A DO NOT OBSTRUCT AIR INTAKE VAC 15A MODEM ANTENNA RX TX LNB AUX BUC TX ANT CTR LNB RX AUX BUC TX BUC DS1 FUSE DS2 FUSE DS3 FUSE DS4 FUSE REAR PANEL FIGURE 1.1 Front and Rear Panels Manual_Rev.B Page 3 07/26/12

4 1.1 Equipment Description (continued) AUX +48 V 1/2A MAX V INPUT +48 V BUC +48 MAX AUX BUC TX (Antenna) LOGIC & CTROL TX (Modem) +18 V LNB (Antenna) VAC INPUT AC PS +48 V RX (Modem) +29 V ANTENNA CTROLLER Block Diagram FIGURE Power Supply Block Diagram Manual_Rev.B Page 4 07/26/12

5 1.2 Technical Characteristics TABLE Power Supply Equipment Specifications* L-Band Insertion RF Input/Outout Characteristics Impedance/Return Loss 50Ω / 10 db minimum Frequency 950 to 2150 MHz and 10 MHz Insertion Loss 1 ± 0.5 db (L-Band); 1 db max. (10 MHz) Frequency Response ± 1.0 db, MHz; ± 0.5 db, 36 MHz BW Output Power Characteristics Voltage/Current, BUC AUX +48 V, 5 A, max. OR +18 V, 3 A selectable Voltage/Current, LNB +18 V, 1 A, max. Voltage/Current, BUC +48 V, 8 A, max. Voltage/Current, TracStar +29 V, 5 A, max. Voltage/Current AUX +48 V +48 V, 500 ma max. Load Regulation ± 5% Primary Input Power Characteristics Voltage/Current, Voltage/Current, AC Connectors Input AC Input BUC TracStar AUX +48 V V, 60A, max. 1200W VAC. 15A, max., Hz, 1200Q Barrier Strip, M5 screw, 3-10 AWG CU wire Schurter with cord Retention TBD (Circular Bayonet 2-pin with sockets) Refer to TracStar documentation Molex 2-pin receptacle with sockets (mating connector: (mating connector: Molex , with pin ). Other RF Connectors (Call for other connectors) Size Power Weight TNC, 50 Ω (female) 19 inch, 1 RU, 3.50 X 12.0 D** V, 1200W OR VAC Hz. 1200W 20 lbs. *10 C to 40 C; Specifications subject to change without notice. **Does not account for connector protrusion TracStar Systems, Inc All Rights Reserved Manual_Rev.B Page 5 07/26/12

6 2.0 Installation 2.1 Mechanical The consists of one RF PCB housed in a 19.0, 2 RU, X 3.50 high X deep chassis. Six front panel locking toggle switches allow the user to disable the power outputs and insertion on all outputs. The can be secured to a rack using the 4 holes on the front panel and six side screws for mounting or using rack slides. Figure 2.0 shows how the is assembled. POWER SUPPLY 19-72V and VAC FIGURE 2.1 Mechanical Assembly Manual_Rev.B Page 6 07/26/12

7 2.2 Rear Panel Inputs, Outputs, and Indicators Figure 2.2 shows the input and output signals and indicators on the rear panel TracStar I/05 refer to TracStar documentation. INPUT Barrier Strip MOLEX 2 pin connector EXHAUST VENT LNB AUX BUC AUX +48V 1/2 AMP MAX ANT MOD PC ICC BUC +48 V 8A MAX V IN 60A DO NOT OBSTRUCT AIR INTAKE VAC 15A MODEM ANTENNA RX TX LNB AUX BUC TX ANT CTR LNB RX AUX BUC TX BUC DS1 FUSE DS2 FUSE DS3 FUSE DS4 FUSE COOLING FANS Intake fans that provide cooling to the power supplies. AC INPUT Schurter w/cord retention +29V FUSE (5A fast-blo) and indicator +18V FUSE (1A fast-blo) and indicator +18/48V FUSE (5A fast-blo) and indicator +48V FUSE (8A fast-blo) and indicator EXHAUST VENTS Do Not Block FIGURE 2.2 Rear Panel Outputs 2.3 Front Panel Controls and Indicators Figure 2.3 shows the front panel controls and indicators. MODEL 2082 POWER SUPPLY CROSS TECHNOLOGIES INC. PRIMARY PWR AC BUC +48V AUX BUC TX SELECT 48V +18V/48V LNB RX +18V ANT CNTR +29V AC 18V LOCKING TOGGLE SWITCH FP SPST Locking Toggle switch (6 places) AC/ Select BUC/ On/Off Status AUX / BUC Loop-through On/Off/Status LNB Loop-through On/Off/Status TracStar On/Off/Status FIGURE 2.3 Front Panel Controls and Indicators Manual_Rev.B Page 7 07/26/12

8 2.4 Installation / Operation Power Supply 1. Connect L-Band Modem to appropriate TX and RX TNC connectors. 2. Connect Antenna to the LNB TNC and the BUC TNC if using the Aux TX power. 3. Connect the BUC power to the Ext BUC power connector if using the BUC Output terminal block (18-12 AWG depending on length). 4. Ensure the AUX BUC Select is in the desired position if using the Aux BUC TX power (either +48V or +18V). 5. Connect the Aux +48V output as desired ensuring not to exceed the 500mA output (mating connector Molex w/pins ). 6. Make sure that all of the on/off switches are in the off position (switches must be pulled out in order to change positions). 7. Connect desired primary power to the input terminal block using a minimum of 8 AWG wire for short distances and 6 AWG or larger (3 AWG max.) for input cables longer than 2 meters. The power source must be capable of supply 60A surge and 45A continuous power. 8. Connect the AC input using the supplied AC power cord and move the locking mechanism to secure the connector. The AC power source must be able to supply a minimum of 15A continuous current. 9. Select either AC or primary power on the front panel. 10. Apply primary power and verify that the shows a standby condition on all outputs and the desired primary power source is indicated. 11. Enable power outputs as desired. Note: The BUC output and Aux BUC TX outputs are interlocked and cannot both be enabled at the same time. Notes: 1. Connecting or disconnecting rear panel connections while power is enabled will result in damage to the connectors and possibly the power supply. 2. An alarm indication on the front panel when power is enabled on any of the four outputs indicates a missing or blown rear panel fuse. 3. The Aux 500mA has a reset able fuse that will open when the output current is exceeded. Should this occur, remove the load from the output and wait five minutes for the fuse to reset. Correct the overloading fault and reconnect the output Manual_Rev.B Page 8 07/26/12

9 3.0 Environmental Use Information A. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions located in the user manual furnished by the manufacturer of your equipment rack. The supply must be braced from the rear as well as the front panel. power B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition does not exist due to uneven weight distribution. C. Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack may be greater than room ambient temperature. Therefore, consideration should be given to Tmra. D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow required for safe operation of the equipment is not compromised. Additional space between units may be required. E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of circuits could have on over current protection and supply wiring. Appropriate consideration of equipment name plate rating should be used when addressing this concern. F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connection to the Branch (use of power strips). G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed. If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS emission problems Manual_Rev.B Page 9 07/26/12

10 CROSS TECHNOLOGIES, INC Shiloh Road Alpharetta, Georgia (770) FAX (770) Toll Free WEB Printed in USA Manual_Rev.B Page 10 07/26/12