COGNEX. Checker SensorView. Quick Reference Guide

Transcription

1 COGNEX Checker SensorView Quick Reference Guide 890

2 SensorView 890 Overview SensorView 890 provides self-contained IP-65 touchscreen configuration, control, and monitoring of one or more Checker 4G series sensors The SensorView 890 must be panel mounted using the SensorView IP-65 Mounting Kit (SV-BKT-000) to achieve IP-65 protection. SensorView 890 Connectors and Controls Insert CF Card 1 Insert supplied CF card in slot. CF card can only be inserted in one orientation (observe markings on label). Do not force insertion. USB Ports CF Card Slot 2 Not used DC-IN - + Ethernet Connector Power Connector Power Switch Not used 2 SensorView 890 Quick Reference Guide SensorView 890 Quick Reference Guide 3

3 Connect to Checker or Network Connect SensorView 890 directly to a single Checker 4G sensor using CAT5 Ethernet cable. Connect to Power 1 2 DC- DC+ Observe polarity as shown. Polarity is marked on power connector on SensorView. Connect 8-35 VDC power to supplied power plug (Dinkle 5ESDV-02P 2P 15A 300V 5mm pitch) Insert plug in SensorView 890 power connector. Connect SensorView 890 to factory network or user-supplied router to manage multiple Checker 4G sensors. 3 Turn power switch ON. 4 SensorView 890 Quick Reference Guide SensorView 890 Quick Reference Guide 5

4 Using SensorView 890 Mounting SensorView 890 For information on connecting and configuring your Checker 4G sensor, refer to the documentation supplied with your Checker 4G sensor. The SensorView 890 supports non-ip panel mounting using four M3 threaded mounting points on the rear of the unit (M3 fasteners not included). Maximum thread depth of mounting points is 6 mm. For additional information, see The SensorView 890 must be panel mounted using the SensorView IP-65 Mounting Kit (PN SV-BKT-000) to achieve IP-65 protection. Mount SensorView using any VESA-compatible (75mm) mounting bracket and supplied hardware. VESA mounting does not provide IP-65 protection. 6 SensorView 890 Quick Reference Guide SensorView 890 Quick Reference Guide 7

5 Specifications Weight Operating Temperature Storage Temperature Maximum Humidity Environmental 468 g 0ºC 50ºC (32ºF 122ºF) -10ºC 60ºC (-14ºF 140ºF) 90% (non-condensing) IP65 (front panel only, when used with IP65 Mounting Kit) Vibration EN61373 including IEC , , and Power Supply Requirements 8 35VDC Maximum 5V: 1.5A Safety DO NOT ATTEMPT TO OPEN OR TO DISASSEMBLE THE CHASSIS (ENCLOSURE) OF THIS PRODUCT. PLEASE CONTACT YOUR COGNEX REPRESENTATIVE FOR ASSISTANCE. Read these Safety instructions carefully. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet. Do not expose the SensorView 890 to rain or moisture, in order to prevent shock and fire hazard. Keep SensorView 890 away from excessive humidity. Never touch un-insulated terminals or wire unless your power adaptor is disconnected. Locate your SensorView 890 as close as possible to wiring connection points. Avoid applying excessive force to cables connected to the SensorView 890. USB connectors supply a maximum of 500 ma. If more power is required by a device, external power must be used. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 8 SensorView 890 Quick Reference Guide SensorView 890 Quick Reference Guide 9

6 Compliance Dimensions (mm) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense. European Compliance The CE mark on the product indicates that the system has been tested to and conforms to the provisions noted within the 2004/108/EC Electromagnetic Compatibility Directive. For further information please contact: Cognex Corporation One Vision Drive Natick, MA USA Cognex Corporation shall not be liable for use of our product with equipment (i.e., power supplies, personal computers, etc.) that is not CE marked and does not comply with the Low Voltage Directive. 10 SensorView 890 Quick Reference Guide SensorView 890 Quick Reference Guide 11

7 Copyright 2012 Cognex Corporation All Rights Reserved. This document may not be copied in whole or in part, nor transferred to any other media or language, without the written permission of Cognex Corporation. The hardware and portions of the software described in this document may be covered by one or more of the U.S. patents listed on the Cognex web site Other U.S. and foreign patents are pending. Cognex, the Cognex logo, SensorView and Checker are trademarks, or registered trademarks, of Cognex Corporation. P/N