RUGGEDCOM Modules. Preface. Introduction 1. Power Supply Modules 2. Copper Ethernet Modules 3. Fiber Optic Ethernet Modules 4.

Transcription

1 Preface Introduction 1 RUGGEDCOM Modules Power Supply Modules 2 Copper Ethernet Modules 3 Fiber Optic Ethernet Modules 4 Serial Modules 5 Control Modules 6 Switch Modules 7 Network Redundancy Modules 8 Blank Modules 9 For MX5000RE 06/2018 RC1333-EN-03

2 RUGGEDCOM Modules Copyright 2018 Siemens Canada Ltd All rights reserved. Dissemination or reproduction of this document, or evaluation and communication of its contents, is not authorized except where expressly permitted. Violations are liable for damages. All rights reserved, particularly for the purposes of patent application or trademark registration. This document contains proprietary information, which is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced or translated to another language without the prior written consent of Siemens Canada Ltd. Disclaimer Of Liability Siemens has verified the contents of this document against the hardware and/or software described. However, deviations between the product and the documentation may exist. Siemens shall not be liable for any errors or omissions contained herein or for consequential damages in connection with the furnishing, performance, or use of this material. The information given in this document is reviewed regularly and any necessary corrections will be included in subsequent editions. We appreciate any suggested improvements. We reserve the right to make technical improvements without notice. Registered Trademarks RUGGEDCOM and ROS are trademarks of Siemens Canada Ltd. Linux is the registered trademark of Linus Torvalds in the United States and other countries. The registered trademark Linux is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a world-wide basis. Other designations in this manual might be trademarks whose use by third parties for their own purposes would infringe the rights of the owner. Security Information Siemens provides products and solutions with industrial security functions that support the secure operation of plants, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens' products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates. For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. For more information about industrial security, visit To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit support.automation.siemens.com. Warranty For warranty details, visit or contact a Siemens customer service representative. Contacting Siemens Address Siemens Canada Ltd Industry Sector 300 Applewood Crescent Concord, Ontario Canada, L4K 5C7 Telephone Toll-free: Tel: Fax: ruggedcom.info.i-ia@siemens.com Web ii

3 RUGGEDCOM Modules Table of Contents Table of Contents Preface... v Alerts... v Related Documents... vi Training... vi Customer Support... vi Ordering RUGGEDCOM Products... vii Chapter 1 Introduction Available Modules Installing/Removing Modules Dimensions... 7 Chapter 2 Power Supply Modules RUGGEDCOM MX5000REPN PS MHIF Chapter 3 Copper Ethernet Modules RUGGEDCOM MX5000REPN LM M4CG RUGGEDCOM MX5000REPN LM M8TX RUGGEDCOM MX5000REPN LM M12TX Chapter 4 Fiber Optic Ethernet Modules RUGGEDCOM MX5000REPN LM M4FG RUGGEDCOM MX5000REPN LM M4FG RUGGEDCOM MX5000REPN LM M4FX RUGGEDCOM MX5000REPN LM M8FX Chapter 5 Serial Modules RUGGEDCOM MX5000REPN LM MS iii

4 Table of Contents RUGGEDCOM Modules Chapter 6 Control Modules RUGGEDCOM MX5000REPN MCM01 L3SEL3HW RUGGEDCOM MX5000REPN CM01 L3SECL3HW Chapter 7 Switch Modules RUGGEDCOM MX5000REPN MSM RUGGEDCOM MX5000REPN SM MSM RUGGEDCOM MX5000REPN SM MSM Chapter 8 Network Redundancy Modules RUGGEDCOM MX5000REPN LM MPRP Chapter 9 Blank Modules RUGGEDCOM MX5000REPN PS XX RUGGEDCOM MX5000REPN LM XX iv

5 RUGGEDCOM Modules Preface Preface This document details RUGGEDCOM power and line modules available for use with devices in the RUGGEDCOM MX5000RE series of multi-service routers and switches. It is intended for use by network technical support personnel responsible for the installation, commissioning and maintenance of routers and switches. It is also recommended for use by network and system planners, system programmers, and line technicians. CONTENTS Alerts Related Documents Training Customer Support Ordering RUGGEDCOM Products Alerts The following types of alerts are used when necessary to highlight important information. DANGER! DANGER alerts describe imminently hazardous situations that, if not avoided, will result in death or serious injury. WARNING! WARNING alerts describe hazardous situations that, if not avoided, may result in serious injury and/or equipment damage. CAUTION! CAUTION alerts describe hazardous situations that, if not avoided, may result in equipment damage. IMPORTANT! IMPORTANT alerts provide important information that should be known before performing a procedure or step, or using a feature. NOTE NOTE alerts provide additional information, such as facts, tips and details. Alerts v

6 Preface RUGGEDCOM Modules Related Documents Other documents that may be of interest include: RUGGEDCOM MX5000RE Installation Guide Training Siemens offers a wide range of educational services ranging from in-house training of standard courses on networking, Ethernet switches and routers, to on-site customized courses tailored to the customer's needs, experience and application. Siemens' Educational Services team thrives on providing our customers with the essential practical skills to make sure users have the right knowledge and expertise to understand the various technologies associated with critical communications network infrastructure technologies. Siemens' unique mix of IT/Telecommunications expertise combined with domain knowledge in the utility, transportation and industrial markets, allows Siemens to provide training specific to the customer's application. For more information about training services and course availability, visit or contact a Siemens Sales representative. Customer Support Customer support is available 24 hours, 7 days a week for all Siemens customers. For technical support or general information, contact Siemens Customer Support through any of the following methods: Online Visit to submit a Support Request (SR) or check on the status of an existing SR. Telephone Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit Mobile App Install the Industry Online Support app by Siemens AG on any Android, Apple ios or Windows mobile device and be able to: Access Siemens' extensive library of support documentation, including FAQs and manuals Submit SRs or check on the status of an existing SR Contact a local Siemens representative from Sales, Technical Support, Training, etc. Ask questions or share knowledge with fellow Siemens customers and the support community vi Related Documents

7 RUGGEDCOM Modules Preface Ordering RUGGEDCOM Products Use the RUGGEDCOM-Selector to select and configure RUGGEDCOM products and accessories. Once selected, an item(s) can be transferred to the Siemens Industry Mall and ordered. RUGGEDCOM-Selector For more information, refer to Ordering RUGGEDCOM Products vii

8 Preface RUGGEDCOM Modules viii Ordering RUGGEDCOM Products

9 RUGGEDCOM Modules Chapter 1 Introduction Introduction This catalog details the various power and line modules available for the RUGGEDCOM MX5000RE. Modules allow network designers to quickly and cost effectively adjust their communications infrastructure to the needs of the facilities and the network. It is intended to be used as a supplement to the Installation Guide for the device: RUGGEDCOM MX5000RE Installation Guide IMPORTANT! Only qualified personnel should be allowed to install and work on this equipment. Qualified persons in the sense of the safety-related notices in this manual are defined as persons who are authorized to commission, to ground, and to tag circuits, equipment, and systems in accordance with established safety practices and standards. CONTENTS Section 1.1, Available Modules Section 1.2, Installing/Removing Modules Section 1.3, Dimensions 1

10 Chapter 1 Introduction RUGGEDCOM Modules Section 1.1 Available Modules The following is a list of all power and line modules available for use in the RUGGEDCOM MX5000RE. NOTE All modules are conformal coated. Power Supply Modules RUGGEDCOM MX5000REPN PS MHIF Specifications Input Range: 88 to 300 VDC or 85 to 264 VAC Terminal Type: Terminal located on chassis Article Numbers 6GK6050-0RL16-0AA1 Copper Ethernet Modules RUGGEDCOM MX5000REPN LM M4CG02 Specifications Ports: 4 Speed: 1000 Mbps Interface: TX Connector: Micro-D Article Numbers 6GK6050-0ML20-0FD1 (Module) 6GK6050-0RL20-0FD1 (Module with Patch Panel and Cables) 6GK6050-0AR00-4RD0 (Patch Panel and Cables) RUGGEDCOM MX5000REPN LM M8TX02 Specifications Ports: 8 Speed: 100 Mbps Interface: TX Connector: Micro-D Article Numbers 6GK6050-0ML20-0ND1 (Module) 6GK6050-0RL20-0ND1 (Module with Patch Panel and Cables) 6GK6050-0AR00-8RD0 (Patch Panel and Cables) RUGGEDCOM MX5000REPN LM M12TX01 Specifications Ports: 12 Speed: 100 Mbps Interface: TX Connector: RJ45 Article Numbers 6GK6050-0ML20-0NB1 (Module) 6GK6050-0RL20-0NE1 (Module with Patch Panel and Cables) 6GK6050-0AR00-6RR0 (Patch Panel and Cables) Fiber Optic Ethernet Modules RUGGEDCOM MX5000REPN LM M8FX11 Specifications Mode: MM Speed: 100 Mbps Interface: FX Ports: 8 Connector: LC Article Numbers 6GK6050-0ML20-0BD1 (Module) 6GK6050-0RL20-0BD1 (Module with Patch Panel and Cables) 6GK6050-0AR00-8MM0 (Patch Panel and Cables) 2 Available Modules

11 RUGGEDCOM Modules Chapter 1 Introduction RUGGEDCOM MX5000REPN LM M4FX11 RUGGEDCOM MX5000REPN LM M4FG01 RUGGEDCOM MX5000REPN LM M4FG03 Distance: 2 km (1.2 mi) Specifications Mode: MM Speed: 100 Mbps Interface: FX Ports: 4 Connector: LC Distance: 2 km (1.2 mi) Specifications Mode: MM Speed: 1000 Mbps Interface: SX Wavelength: 850 nm Ports: 4 Connector: LC Distance: 500 m (1640 ft) Specifications Mode: SM Speed: 1000 Mbps Interface: LX Wavelength: 1310 nm Ports: 4 Connector: LC Distance: 10 Km (6 mi) Article Numbers 6GK6050-0ML20-0BH1 (Module) 6GK6050-0RL20-0BH1 (Module with Patch Panel and Cables) 6GK6050-0AR00-4MM0 (Patch Panel and Cables) Article Numbers 6GK6050-0ML20-0BK1 (Module) 6GK6050-0RL20-0BK1 (Module with Patch Panel and Cables) 6GK6050-0AR00-4MM0 (Patch Panel and Cables) Article Numbers 6GK6050-0ML20-0CR1 (Module) 6GK6050-0RL20-0CR1 (Module with Patch Panel and Cables) 6GK6050-0AR00-4SM0 (Patch Panel and Cables) Serial Modules RUGGEDCOM MX5000REPN LM MS01 Specifications Standard: RS232/RS422/RS485 Ports: 8 Connector: DB9 Article Numbers 6GK6050-0ML20-0KB1 (Module) 6GK6050-0RL20-0KB1 (Module with Patch Panel and Cables) 6GK6050-0AR00-8DR0 (Patch Panel and Cables) Control Modules RUGGEDCOM MX5000REPN MCM01 L3SEL3HW Specifications Layer 3 Standard Edition, Layer 3 Hardware Article Numbers 6GK6050-0ML30-0BA1 (Module) 6GK6050-0RL30-0BA1 (Module with Patch Panel and Cables) 6GK6050-0AR00-1CP0 (Patch Panel and Cables) Available Modules 3

12 Chapter 1 Introduction RUGGEDCOM Modules RUGGEDCOM MX5000REPN MCM01 L3SECL3HW Specifications Layer 3 Security Edition, Layer 3 Hardware Article Numbers 6GK6050-0ML30-0CA1 (Module) 6GK6050-0RL30-0CA1 (Module with Patch Panel and Cables) 6GK6050-0AR00-1CP0 (Patch Panel and Cables) Switch Modules RUGGEDCOM MX5000REPN MSM36 RUGGEDCOM MX5000REPN MSM61 Specifications Mode: SM Speed: 1000 Mbps Interface: LX Wavelength: 1310 nm Ports: 2 Connector: LC Distance: 10 Km (6 mi) Specifications Layer 3 Article Numbers 6GK6050-0ML40-0RA1 (Module) 6GK6050-0RL40-0RA1 (Module with Patch Panel and Cables) 6GK6050-0AR00-1SP0 (Patch Panel and Cables) Article Numbers 6GK6050-0ML40-0VA1 (Module) 6GK6050-0RL40-0VA1 (Module with Patch Panel and Cables) 6GK6050-0AR00-0XF0 (Patch Panel and Cables) RUGGEDCOM MX5000REPN MSM70 Specifications SFP Sockets: 2 Speed: 10 Gbps Network Layer: Layer 3 Article Numbers 6GK6050-0ML40-0XA1 (Module) 6GK6050-0RL40-0WA1 (Module with Patch Panel and Cables) 6GK6050-0AR00-1SP0 (Patch Panel and Cables) Network Redundancy Modules RUGGEDCOM MX5000REPN LM MPRP Specifications Ports: 2 Speed: 1000 Mbps Interface: LX Port Type: RJ45 Distance: 10 km (6.2 mi) Protocol: PRP Article Numbers 6GK6050-0ML20-0PR1 (Module) 6GK6050-0RL20-0PR1 (Module with Patch Panel and Cables) 6GK6050-0AR00-2PR0 (Patch Panel and Cables) 4 Available Modules

13 RUGGEDCOM Modules Chapter 1 Introduction Blank Modules RUGGEDCOM MX5000REPN PS XX Specifications Blank power supply module, full panel Article Numbers 6GK6050-0RL10-0AA1 RUGGEDCOM MX5000REPN LM XX Specifications Blank line module, half panel Article Numbers 6GK6050-0RL20-0AA1 Available Modules 5

14 Chapter 1 Introduction RUGGEDCOM Modules Section 1.2 Installing/Removing Modules Always refer to the Installation Guide for the RUGGEDCOM MX5000RE for instructions on how to install or remove a power or line module. The Installation Guide cites important, chassis-specific safety warnings that should be followed to avoid damage to the module and/or device. Additional installation/removal instructions may also be provided in this for select modules. Make sure to review all information provided for a module before installing or removing it. 6 Installing/Removing Modules

15 RUGGEDCOM Modules Chapter 1 Introduction Section 1.3 Dimensions Power and line modules conform to the following dimensions: NOTE All dimensions are in millimeters (mm) Figure 1: Power and Line Module Dimensions Dimensions 7

16 Chapter 1 Introduction RUGGEDCOM Modules 8 Dimensions

17 RUGGEDCOM Modules Chapter 2 Power Supply Modules Power Supply Modules The following power supply modules are available for the RUGGEDCOM MX5000RE. CONTENTS Section 2.1, RUGGEDCOM MX5000REPN PS MHIF 9

18 Chapter 2 Power Supply Modules RUGGEDCOM Modules Section 2.1 RUGGEDCOM MX5000REPN PS MHIF The RUGGEDCOM MX5000REPN PS MHIF power supply module provides high VDC or VAC power to the RUGGEDCOM MX5000RE and features a failsafe relay to protect against critical error conditions. The module accepts either AC or DC power inputs from an external power supply. IMPORTANT! The required power input for the RUGGEDCOM MX5000REPN PS MHIF is located on the chassis. For more information about the RUGGEDCOM MX5000RE chassis options, refer to Article Number 6GK6050-0MB00-0AG1 and 6GK6050-0MB00-0AG2. LEDs indicate when the module is receiving and supplying power. LED State Description O Green The module is supplying power I Green The module is receiving power 1 2 Figure 2: RUGGEDCOM MX5000REPN PS MHIF 1. I LED 2. O LED Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Characteristics Environment Input Range 88 to 300 VDC or 85 to 264 VAC Ingress Protection IP30 Internal Fuse Rating 6.3 A, 250 V(T) a Operating Temperature -40 to 85 C (-40 to 185 F) Maximum Power Consumption b Insulation 84 W c 2800 VDC for 1 minute Operating Relative Humidity Storage Temperature 5 to 95% (non-condensing) -40 to 85 C (-40 to 185 F) a (T) denotes time-delay fuse. Internal fuse is not user-replaceable. b Power consumption varies based on the device configuration. c Rating at 85 C (185 F) ambient temperature at worst-case load. Ordering Information Description Article Numbers VDC or VAC, supports terminal block on front. 6GK6050-0RL16-0AA1 10 RUGGEDCOM MX5000REPN PS MHIF

19 RUGGEDCOM Modules Chapter 3 Copper Ethernet Modules Copper Ethernet Modules The following copper Ethernet modules are available for the RUGGEDCOM MX5000RE. CONTENTS Section 3.1, RUGGEDCOM MX5000REPN LM M4CG02 Section 3.2, RUGGEDCOM MX5000REPN LM M8TX02 Section 3.3, RUGGEDCOM MX5000REPN LM M12TX01 11

20 Chapter 3 Copper Ethernet Modules RUGGEDCOM Modules Section 3.1 RUGGEDCOM MX5000REPN LM M4CG02 The RUGGEDCOM MX5000REPN LM M4CG02 module features four 10/100/1000Base-TX Micro-D ports. IMPORTANT! This module is only compatible with RUGGEDCOM MX5000REPN SM 61. Each port features a dedicated LED that indicates its link/activity state. State Description 2 Green (Solid) Green (Blinking) Off Link established Activity No link detected Figure 3: RUGGEDCOM MX5000REPN LM M4CG02 1. Alarm LED 2. Micro-D Ports 3. Port LEDs Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Pin-Out Description The following are the pin-out descriptions for the Micro-D ports: Pin 10/100Base-TX 1000Base-TX 1 1 TX+ B+ 2 Reserved (Do Not Connect) D+ 3 Reserved (Do Not Connect) 4 Reserved (Do Not Connect) C+ 6 Figure 4: Micro-D 10/100Base-TX Port Pin Configuration 5 RX+ A+ 6 TX- B- 7 Reserved (Do Not Connect) D- 8 Reserved (Do Not Connect) C- 9 RX- A- 12 RUGGEDCOM MX5000REPN LM M4CG02

21 RUGGEDCOM Modules Chapter 3 Copper Ethernet Modules Technical Specifications Characteristics Environment Speed 10/100/1000 Mbps Ingress Protection IP40 Interface TX Operating Temperature -40 to 85 C (-40 to 185 F) Connector Micro-D Operating Relative Humidity 5 to 95% (non-condensing) Cable Type > CAT-5 Storage Temperature -40 to 85 C (-40 to 185 F) Duplex FDX/HDX Wiring Standard TIA/EIA T568A/B Nominal Distance 100 m (328.1 ft) Isolation 1.5 kv Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module 4 x 10/100/1000TX Micro-D 6GK6050-0ML20-0FD1 Module with Patch Panel and Cables 4 x 10/100/1000TX Micro-D 6GK6050-0RL20-0FD1 Patch Panel and Cables 4 x Micro-D connectors to RJ45 connectors 6GK6050-0AR00-4RD0 RUGGEDCOM MX5000REPN LM M4CG02 13

22 Chapter 3 Copper Ethernet Modules RUGGEDCOM Modules Section 3.2 RUGGEDCOM MX5000REPN LM M8TX02 The RUGGEDCOM MX5000REPN LM M8TX02 module features eight 10/100Base-TX Micro-D ports. Each port features a dedicated LED that indicates its link/activity state. State Description 2 2 Green (Solid) Green (Blinking) Off Link established Activity No link detected 1 3 Figure 5: RUGGEDCOM MX5000REPN LM M8TX02 1. Alarm LED 2. Port LEDs 3. Micro-D Ports Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Pin-Out Description The following are the pin-out descriptions for the Micro-D ports: Pin 10/100Base-TX 1000Base-TX 1 1 TX+ B+ 2 Reserved (Do Not Connect) D+ 3 Reserved (Do Not Connect) 4 Reserved (Do Not Connect) C+ 6 Figure 6: Micro-D 10/100Base-TX Port Pin Configuration 5 RX+ A+ 6 TX- B- 7 Reserved (Do Not Connect) D- 8 Reserved (Do Not Connect) C- 9 RX- A- Technical Specifications Characteristics Environment 14 RUGGEDCOM MX5000REPN LM M8TX02

23 RUGGEDCOM Modules Chapter 3 Copper Ethernet Modules Speed 10/100 Mbps Ingress Protection IP40 Interface TX Operating Temperature -40 to 85 C (-40 to 185 F) Connector Micro-D Operating Relative Humidity 5 to 95% (non-condensing) Duplex FDX/HDX Storage Temperature -40 to 85 C (-40 to 185 F) Cable Type > CAT-5 Wiring Standard TIA/EIA T568A/B Nominal Distance 100 m (328.1 ft) Isolation 1.5 kv Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module 8 x 10/100Base-TX Micro-D 6GK6050-0ML20-0ND1 Module with Patch Panel and Cables 8 x 10/100Base-TX Micro-D 6GK6050-0RL20-0ND1 Patch Panel and Cables 8 x Micro-D connectors to RJ45 connectors 6GK6050-0AR00-8RD0 RUGGEDCOM MX5000REPN LM M8TX02 15

24 Chapter 3 Copper Ethernet Modules RUGGEDCOM Modules Section 3.3 RUGGEDCOM MX5000REPN LM M12TX01 The RUGGEDCOM MX5000REPN LM M12TX01 module features sixteen 10/100 Base-TX RJ45 ports, but only twelve ports are connected to the RUGGEDCOM MX5000RE enclosure via the associated patch panel. The module features two dedicated LEDs to indicate link/activity state. LED State Description 2 3 Speed Yellow The port is operating at 1000 Mbps Off The port is operating at 10 or 100 Mbps Link/Activity Yellow (Solid) Link established Yellow (Blinking) Activity 1 4 Off No link detected Figure 7: RUGGEDCOM MX5000REPN LM M12TX01 1. Alarm LED 2. Speed LED 3. Link/Activity LED 4. Ethernet Ports Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Pin-Out Description The following are the pin-out descriptions for the RJ45 ports: 8 1 Pin 10/100Base-TX Name 1000Base-TX Description 1 RX+ BI_DB+ Receive Data+ or Bi-Directional Figure 8: RJ45 Ethernet Port Pin Configuration 2 RX- BI_DB- Receive Dataor Bi-Directional 3 TX+ BI_DA+ Transmit Data+ or Bi-Directional 4 Reserved (Do Not Connect) 5 Reserved (Do Not Connect) 6 TX- BI_DA- Transmit Dataor Bi-Directional 7 Reserved (Do Not Connect) 8 Reserved (Do Not Connect) 16 RUGGEDCOM MX5000REPN LM M12TX01

25 RUGGEDCOM Modules Chapter 3 Copper Ethernet Modules Technical Specifications Characteristics Environment Speed 10/100 Mbps Ingress Protection IP40 Interface TX Operating Temperature -40 to 85 C (-40 to 185 F) Connector RJ45 Operating Relative Humidity 5 to 95% (non-condensing) Cable Type > CAT-5 Storage Temperature -40 to 85 C (-40 to 185 F) Duplex FDX/HDX Wiring Standard TIA/EIA T568A/B Nominal Distance 100 m (328.1 ft) Isolation 1.5 kv Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module 16 x 10/100Base-TX RJ45 6GK6050-0ML20-0NB1 Module with Patch Panel and Cables 12 x 10/100Base-TX RJ45 6GK6050-0RL20-0NE1 Patch Panel and Cables 12 x RJ45 connectors to RJ45 connectors 6GK6050-0AR00-6RR0 RUGGEDCOM MX5000REPN LM M12TX01 17

26 Chapter 3 Copper Ethernet Modules RUGGEDCOM Modules 18 RUGGEDCOM MX5000REPN LM M12TX01

27 RUGGEDCOM Modules Chapter 4 Fiber Optic Ethernet Modules Fiber Optic Ethernet Modules The following fiber optic Ethernet modules are available for the RUGGEDCOM MX5000RE. CONTENTS Section 4.1, RUGGEDCOM MX5000REPN LM M4FG01 Section 4.2, RUGGEDCOM MX5000REPN LM M4FG03 Section 4.3, RUGGEDCOM MX5000REPN LM M4FX11 Section 4.4, RUGGEDCOM MX5000REPN LM M8FX11 19

28 Chapter 4 Fiber Optic Ethernet Modules RUGGEDCOM Modules Section 4.1 RUGGEDCOM MX5000REPN LM M4FG01 The RUGGEDCOM MX5000REPN LM M4FG01 module features four 1000Base-SX fiber optic Ethernet ports. IMPORTANT! This module is only compatible with RUGGEDCOM MX5000REPN SM 61. NOTE When connecting cables, make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. Each port set (transmit/receive) features a dedicated LED that indicates its link/activity state. State Description 2 Green (Solid) Green (Blinking) Off Link established Activity No link detected Figure 9: RUGGEDCOM MX5000REPN LM M4FG01 1. Alarm LED 2. Ethernet Ports 3. Port LEDs Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Optical Characteristics Cabling Transmit Power -9 to -2.5 dbm Speed 1 Gbps Receiver Sensitivity -20 dbm Mode MM (Multi-Mode) Receiver Saturation 0 dbm Interface SX Power Budget 11 db Connector LC Environment Ingress Protection Operating Temperature IP40-40 to 85 C (-40 to 185 F) Cable Type Wavelength a Nominal Distance a 62.5/125 μm 850 nm 0.5 km (0.3 mi) Operating Relative Humidity 5 to 95% (non-condensing) 20 RUGGEDCOM MX5000REPN LM M4FG01

29 RUGGEDCOM Modules Chapter 4 Fiber Optic Ethernet Modules Storage Temperature -40 to 85 C (-40 to 185 F) a Typical. Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module 4 x 1000SX, Multimode, 850nm, LC, 500m 6GK6050-0ML20-0BK1 Module with Patch Panel and Cables 4 x 1000SX, Multimode, 850nm, LC, 500m 6GK6050-0RL20-0BK1 Patch Panel and Cables 4 x Multi Mode Military Circular Fiber Connectors with LC connectors 6GK6050-0AR00-4MM0 RUGGEDCOM MX5000REPN LM M4FG01 21

30 Chapter 4 Fiber Optic Ethernet Modules RUGGEDCOM Modules Section 4.2 RUGGEDCOM MX5000REPN LM M4FG03 The RUGGEDCOM MX5000REPN LM M4FG03 module features four 1000Base-LX fiber optic Ethernet ports. IMPORTANT! This module is only compatible with RUGGEDCOM MX5000REPN SM 61. NOTE When connecting cables, make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. Each port set (transmit/receive) features a dedicated LED that indicates its link/activity state. State Description 1 Green (Solid) Green (Blinking) Off Link established Activity No link detected 2 2 Figure 10: RUGGEDCOM MX5000REPN LM M4FG03 1. Ethernet Ports 2. Port LEDs Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Optical Characteristics Cabling Transmit Power -9.5 to -3 dbm Speed 1000Base-LX Receiver Sensitivity -21 dbm Mode Single-Mode Receiver Saturation -3 dbm Interface LC Power Budget 11.5 db Cable Type 9/125 μm Environment Ingress Protection IP40 Wavelength b Nominal Distance a 1310 nm 10 km (6.2 mi) Operating Temperature -40 to 85 C (-40 to 185 F) Operating Relative Humidity 5 to 95% (non-condensing) 22 RUGGEDCOM MX5000REPN LM M4FG03

31 RUGGEDCOM Modules Chapter 4 Fiber Optic Ethernet Modules Storage Temperature -40 to 85 C (-40 to 185 F) b Typical. Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module 4x 1000LX Singlemode, 1310nm, LC, 10km 6GK6050-0ML20-0CR1 Module with Patch Panel and Cables 4x 1000LX Singlemode, 1310nm, LC, 10km 6GK6050-0RL20-0CR1 Patch Panel and Cables 4 x Single Mode Military Circular Fiber Connectors with LC connectors 6GK6050-0AR00-4SM0 RUGGEDCOM MX5000REPN LM M4FG03 23

32 Chapter 4 Fiber Optic Ethernet Modules RUGGEDCOM Modules Section 4.3 RUGGEDCOM MX5000REPN LM M4FX11 The RUGGEDCOM MX5000REPN LM M4FX11 module features four 100Base-FX fiber optic Ethernet ports. NOTE When connecting cables, make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. Each port set (transmit/receive) features a dedicated LED that indicates its link/activity state. State Description 2 Green (Solid) Green (Blinking) Off Link established Activity No link detected Figure 11: RUGGEDCOM MX5000REPN LM M4FX11 1. Alarm LED 2. Ethernet Ports 3. Port LEDs Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Optical Characteristics Cabling Transmit Power -19 to -14 dbm Speed 100 Mbps Receiver Sensitivity -32 dbm Mode MM (Multi-Mode) Receiver Saturation -14 dbm Interface FX Power Budget 13 db Connector LC Environment Ingress Protection Operating Temperature IP40-40 to 85 C (-40 to 185 F) Cable Type Wavelength c Nominal Distance a 62.5/125 μm 1300 nm 2 km (1.2 mi) Operating Relative Humidity 5 to 95% (non-condensing) Storage Temperature -40 to 85 C (-40 to 185 F) c Typical. 24 RUGGEDCOM MX5000REPN LM M4FX11

33 RUGGEDCOM Modules Chapter 4 Fiber Optic Ethernet Modules Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module 4 x 100FX, Multimode, 1300nm, LC, 2km 6GK6050-0ML20-0BH1 Module with Patch Panel and Cables 4 x 100FX, Multimode, 1300nm, LC, 2km 6GK6050-0RL20-0BH1 Patch Panel and Cables 4 x Multi Mode Military Circular Fiber Connectors with LC connectors 6GK6050-0AR00-4MM0 RUGGEDCOM MX5000REPN LM M4FX11 25

34 Chapter 4 Fiber Optic Ethernet Modules RUGGEDCOM Modules Section 4.4 RUGGEDCOM MX5000REPN LM M8FX11 The RUGGEDCOM MX5000REPN LM M8FX11 module features eight 100Base-FX fiber optic Ethernet ports. NOTE When connecting cables, make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. Each port set (transmit/receive) features a dedicated LED that indicates its link/activity state. State Description 1 Green (Solid) Green (Blinking) Off Link established Activity No link detected Figure 12: RUGGEDCOM MX5000REPN LM M8FX11 1. Ethernet Ports 2. Alarm LED 3. Port LEDs Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Optical Characteristics Cabling Transmit Power -19 to -14 dbm Speed 100 Mbps Receiver Sensitivity -32 dbm Mode MM (Multi-Mode) Receiver Saturation -14 dbm Interface FX Power Budget 13 db Connector LC Environment Ingress Protection Operating Temperature IP40-40 to 85 C (-40 to 185 F) Cable Type Wavelength d Nominal Distance 62.5/125 μm 1300 nm 2 km (1.2 mi) Operating Relative Humidity 5 to 95% (non-condensing) Storage Temperature -40 to 85 C (-40 to 185 F) d Typical. 26 RUGGEDCOM MX5000REPN LM M8FX11

35 RUGGEDCOM Modules Chapter 4 Fiber Optic Ethernet Modules Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module 8 x 100FX, Multimode, 1300nm, LC, 2km 6GK6050-0ML20-0BD1 Module with Patch Panel and Cables 8 x 100FX, Multimode, 1300nm, LC, 2km 6GK6050-0RL20-0BD1 Patch Panel and Cables 8 x Multi Mode Military Circular Fiber Connectors with LC connectors 6GK6050-0AR00-8MM0 RUGGEDCOM MX5000REPN LM M8FX11 27

36 Chapter 4 Fiber Optic Ethernet Modules RUGGEDCOM Modules 28 RUGGEDCOM MX5000REPN LM M8FX11

37 RUGGEDCOM Modules Chapter 5 Serial Modules Serial Modules The following serial modules are available for the RUGGEDCOM MX5000RE. CONTENTS Section 5.1, RUGGEDCOM MX5000REPN LM MS01 29

38 Chapter 5 Serial Modules RUGGEDCOM Modules Section 5.1 RUGGEDCOM MX5000REPN LM MS01 The RUGGEDCOM MX5000REPN LM MS01 module features eight serial DB9 ports that may be used with a null modem (crossover) serial cable. 2 1 Figure 13: RUGGEDCOM MX5000PN LM MS01 1. Alarm LED 2. Serial Ports Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Operating Modes Each serial port can be run in RS232, RS485 or RS422 mode. On initial power-up, all serial ports default to RS485 mode. However, each port can be individually set to RS232, RS485 or RS422 mode via RUGGEDCOM ROX II. For more information, refer to the RUGGEDCOM ROX II User Guide for the RUGGEDCOM MX5000RE. Pin-Out Description The following are the pin-outs for the DB9 connectors: 5 1 Pin Function RS232 Mode RS422 Mode RS485 Mode Figure 14: DB9 Serial Port RX- 2 RX TX+ TX+/RX+ 3 TX RX+ 4 Reserved (Do Not Connect) 5 COM (Isolated GND) 6 COM (Isolated GND) 7 TX- TX-/RX- 8 Reserved (Do Not Connect) 30 RUGGEDCOM MX5000REPN LM MS01

39 RUGGEDCOM Modules Chapter 5 Serial Modules Pin Function RS232 Mode RS422 Mode RS485 Mode 9 COM (Isolated GND) Body Screws Chassis GND a Chassis GND a a Connected internally. Connecting to RS485 Devices Each RS485 port can communicate with multiple RS485 devices by wiring devices together in sequence over a single twisted pair with transmit and receive signals on the same two wires (half duplex). For reliable, continuous communication, adhere to the following guidelines: To minimize the effects of ambient electrical noise, use shielded cabling. The correct polarity must be observed throughout a single sequence or ring. The number of devices wired should not exceed 32, and total distance should be less than 1219 m (4000 ft) at 100 kbps. The Common terminals should be connected to the common wire inside the shield. The shield should be connected to earth ground at a single point to avoid loop currents. The twisted pair should be terminated at each end of the chain. The following shows the recommended RS485 wiring < 1219 m (4000 in) 120Ω 10nF 6 120Ω 10nF Figure 15: Recommended RS485 Wiring 1. MX5000RE Device 2. Common (Isolated Ground) 3. Negative 4. Positive 5. Shield to Earth (Connected At a Single Point) 6. RS485 Devices (32 Total) RUGGEDCOM MX5000REPN LM MS01 31

40 Chapter 5 Serial Modules RUGGEDCOM Modules Technical Specifications Characteristics Environment Baud Rate 1200 to kbps Ingress Protection IP40 Connector DB9 Operating Temperature -40 to 85 C (-40 to 185 F) Isolation 2.5 kv Operating Relative Humidity 5 to 95% (non-condensing) Storage Temperature -40 to 85 C (-40 to 185 F) Certification This module has been certified to comply with the requirements of the relevant standards. Category Standard EMC FCC Part 15 (Class A), EN (CISPR22 Class A), IEC , IEEE 1613 Safety UL , CSA C22.2 No Hazardous Location (CSA/UL) Class I, Div 2 Emitted Interference EN (Class A) Interference Immunity EN Railway EN 50155, EN Ordering Information Item Description Article Number Module Module with Patch Panel and Cables 8 x RS232/RS422/RS485 via DB9 Serial Line Module 8 x RS232/RS422/RS485 via DB9 Serial Line Module 6GK6050-0ML20-0KB1 6GK6050-0RL20-0KB1 Patch Panel and Cables Panels for MX5000RE Serial module. 6GK6050-0AR00-8DR0 32 RUGGEDCOM MX5000REPN LM MS01

41 RUGGEDCOM Modules Chapter 6 Control Modules Control Modules Control modules are the central processing engine for the device. The RUGGEDCOM ROX II operating system running on the module controls and coordinates the functions of all modules installed in the system. Each control module is equipped with an RS232 serial console port for initial management functions, and a locally connected 10/100Base-T Ethernet port for system management out-of-band from the switch fabric. Other features include: Alarm LED to indicate the system status Removable 1 GB Compact Flash (CF) card, which contains active and fallback installations of the RUGGEDCOM ROX II operating system, the configuration database, and other system data A failsafe alarm relay, activated by the operating system to indicate a critical alarm. A lamp test and alarm cutoff button A utility USB port for uploading/downloading files The following control modules are available for the RUGGEDCOM MX5000RE. CONTENTS Section 6.1, RUGGEDCOM MX5000REPN MCM01 L3SEL3HW Section 6.2, RUGGEDCOM MX5000REPN CM01 L3SECL3HW 33

42 Chapter 6 Control Modules RUGGEDCOM Modules Section 6.1 RUGGEDCOM MX5000REPN MCM01 L3SEL3HW The RUGGEDCOM MX5000REPN MCM01 L3SEL3HW control module features Layer 3 hardware and is preconfigured with RUGGEDCOM ROX II Layer 3 Standard Edition Figure 16: RUGGEDCOM MX5000REPN MCM01 L3SEL3HW 1. LT/ACO Button 2. CF Card Slot 3. Alarm LED 4. MGMT Port 5. USB Port 6. Console Port 7. Failsafe Relay Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Operating Temperature Operating Relative Humidity Storage Temperature -40 to 85 C (-40 to 185 F) 5 to 95% (non-condensing) -40 to 85 C (-40 to 185 F) Ordering Information Item Description Article Number Module Module with Patch Panel and Cables Control module with Layer 3 Standard Edition Layer 3 hardware Control module with Layer 3 Standard Edition Layer 3 hardware 6GK6050-0ML30-0BA1 6GK6050-0RL30-0BA1 Patch Panel and Cables Panels for MX5000RE Control Module 6GK6050-0AR00-1CP0 34 RUGGEDCOM MX5000REPN MCM01 L3SEL3HW

43 RUGGEDCOM Modules Chapter 6 Control Modules Section 6.2 RUGGEDCOM MX5000REPN CM01 L3SECL3HW The RUGGEDCOM MX5000REPN CM01 L3SECL3HW control module features Layer 3 hardware and is preconfigured with RUGGEDCOM ROX II Layer 3 Security Edition Figure 17: RUGGEDCOM MX5000REPN CM01 L3SECL3HW 1. LT/ACO Button 2. CF Card Slot 3. Alarm LED 4. MGMT Port 5. USB Port 6. Console Port 7. Failsafe Relay Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Operating Temperature Operating Relative Humidity Storage Temperature -40 to 85 C (-40 to 185 F) 5 to 95% (non-condensing) -40 to 85 C (-40 to 185 F) Ordering Information Item Description Article Number Module Module with Patch Panel and Cables Control module with Layer 3 Security Edition Layer 3 hardware Control module with Layer 3 Security Edition Layer 3 hardware 6GK6050-0ML30-0CA1 6GK6050-0RL30-0CA1 Patch Panel and Cables Panels for MX5000RE Control Module 6GK6050-0AR00-1CP0 RUGGEDCOM MX5000REPN CM01 L3SECL3HW 35

44 Chapter 6 Control Modules RUGGEDCOM Modules 36 RUGGEDCOM MX5000REPN CM01 L3SECL3HW

45 RUGGEDCOM Modules Chapter 7 Switch Modules Switch Modules Switch modules connect devices together on a computer network by using packet switching to receive, process and forward data to the destination device. The following switch modules are available for the RUGGEDCOM MX5000RE. CONTENTS Section 7.1, RUGGEDCOM MX5000REPN MSM36 Section 7.2, RUGGEDCOM MX5000REPN SM MSM61 Section 7.3, RUGGEDCOM MX5000REPN SM MSM70 37

46 Chapter 7 Switch Modules RUGGEDCOM Modules Section 7.1 RUGGEDCOM MX5000REPN MSM36 The RUGGEDCOM MX5000REPN MSM36 module features two 1000Base-LX fiber optic Ethernet ports. NOTE When connecting cables, make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. Each port set (transmit/receive) features a dedicated LED that indicates its link/activity state. State Description 2 Green (Solid) Green (Blinking) Off Link established Activity No link detected 1 3 Figure 18: RUGGEDCOM MX5000REPN MSM36 1. Alarm LED 2. Ethernet Ports 3. Port LEDs Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Optical Characteristics Cabling Transmit Power -10 to -3 dbm Speed 1 Gbps Receiver Sensitivity -20 dbm Mode SM (Single-Mode) Receiver Saturation -3 dbm Interface LX Power Budget 10 db Connector LC Environment Operating Temperature Operating Relative Humidity Storage Temperature a Typical. -40 to 85 C (-40 to 185 F) 5 to 95% (non-condensing) -40 to 85 C (-40 to 185 F) Cable Type 9/125 μm Wavelength a 1310 Nominal Distance a 10 km (6.2 mi) 38 RUGGEDCOM MX5000REPN MSM36

47 RUGGEDCOM Modules Chapter 7 Switch Modules Ordering Information Item Description Article Number Module 2x 1000LX singlemode, 1310nm, LC, 10km 6GK6050-0ML40-0RA1 Module with Patch Panel and Cables Patch Panel and Cables 2x 1000LX singlemode, 1310nm, LC, 10km 2 x Singlemode Military Circular Fiber Connectors with LC connectors 6GK6050-0RL40-0RA1 6GK6050-0AR00-1SP0 RUGGEDCOM MX5000REPN MSM36 39

48 Chapter 7 Switch Modules RUGGEDCOM Modules Section 7.2 RUGGEDCOM MX5000REPN SM MSM61 The RUGGEDCOM MX5000REPN SM MSM61 is a Layer 3/88 Gigabit throughput switch module that enables Gigabit throughput for up to 24 fiber optic Ethernet ports. 1 Figure 19: RUGGEDCOM MX5000REPN SM MSM61 1. Alarm LED Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Operating Temperature -40 to 85 C (-40 to 185 F) Ordering Information Item Description Article Number Module Module with Patch Panel and Cables Layer 3/88 Gigabit Throughput, no uplink ports Layer 3/88 Gigabit Throughput, no uplink ports 6GK6050-0ML40-0VA1 6GK6050-0RL40-0VA1 Patch Panel and Cables Full Blank Panel 6GK6050-0AR00-0XF0 40 RUGGEDCOM MX5000REPN SM MSM61

49 RUGGEDCOM Modules Chapter 7 Switch Modules Section 7.3 RUGGEDCOM MX5000REPN SM MSM70 The RUGGEDCOM MX5000REPN SM MSM70 is a Layer 3/88 Gigabit throughput switch module that enables Gigabit throughput for up to 24 fiber optic Ethernet ports. It also features sockets for up to two Small Form-factor Pluggable (SFP) transceivers. NOTE When connecting cables, make sure the Transmit (Tx) and Receive (Rx) connections of each port are properly connected and matched to establish a proper link. Each transceiver socket features a dedicated LED that indicates the link/activity state of the associated SFP transceiver. State Description 2 Green (Solid) Green (Blinking) Off Link established Activity No link detected 1 3 Figure 20: RUGGEDCOM MX5000REPN SM MSM70 1. Alarm LED 2. SFP Transceiver Sockets 3. Port LEDs This module is only compatible with the following fiber optic Ethernet modules: RUGGEDCOM MX5000REPN LM M8FX11 Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Optical Characteristics Cabling Transmit Power -8.2 to 0.5 dbm Speed 10 Gbps Tx Minimum OMA -5.2 Minimum Extinction Ratio 3.5 Receiver Sensitivity OMA (dbm) Stressed RX Sensitivity (dbm) Receiver Saturation (dbm) 0.5 Power Budget (db) 4.4 Mode Interface Connector Cable Type Wavelength Nominal Distance SM (Single-Mode) LR LC 9/125 μm 1310 nm 10 km (6.2 mi) RUGGEDCOM MX5000REPN SM MSM70 41

50 Chapter 7 Switch Modules RUGGEDCOM Modules Channel Insertion Loss (db) 5.1 Allocation for Penalties (db) 2.3 Environment Operating Temperature Operating Relative Humidity Storage Temperature -40 to 85 C (-40 to 185 F) 0 to 85% (non-condensing) -40 to 85 C (-40 to 185 F) Ordering Information Item Description Article Number Module Layer 3/88 Gigabit Throughput, 2x 10G 6GK6050-0ML40-0XA1 Module with Patch Panel and Cables Layer 3/88 Gigabit Throughput, 2x 10G 6GK6050-0RL40-0WA1 Patch Panel and Cables 2 x Singlemode Military Circular Fiber Connectors with LC connectors 6GK6050-0AR00-1SP0 42 RUGGEDCOM MX5000REPN SM MSM70

51 RUGGEDCOM Modules Chapter 8 Network Redundancy Modules Network Redundancy Modules The following modules provide network redundancy functionality for the RUGGEDCOM MX5000RE. CONTENTS Section 8.1, RUGGEDCOM MX5000REPN LM MPRP 43

52 Chapter 8 Network Redundancy Modules RUGGEDCOM Modules Section 8.1 RUGGEDCOM MX5000REPN LM MPRP The RUGGEDCOM MX5000REPN LM MPRP module enables the device the interact with a redundancy network using the Parallel Redundancy Protocol (PRP). The module features individual Ethernet ports for connecting to each side of the network. NOTE For more information about PRP, refer to the RUGGEDCOM ROX II User Guide for the RUGGEDCOM MX5000RE Figure 21: RUGGEDCOM MX5000REPN LM MPRP 1. Alarm LED 2. Ethernet Ports 3. Port LEDs Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Technical Specifications Optical Characteristics Cabling Transmit Power -9.5 to -3.0 dbm Speed 1 Gbps Receiver Sensitivity to -3.0 dbm Mode SM (Single-Mode) Power Budget 9.5 db Interface LX Environment Connector LC Operating Temperature Operating Relative Humidity Storage Temperature -40 to 85 C (-40 to 185 F) 5 to 95% (non-condensing) -40 to 85 C (-40 to 185 F) Cable Type Wavelength Nominal Distance 9/125 μm 1310 nm 10 km (6.2 mi) 44 RUGGEDCOM MX5000REPN LM MPRP

53 RUGGEDCOM Modules Chapter 8 Network Redundancy Modules Ordering Information Item Description Article Number Module Module with Patch Panel and Cables 1x Pair (A/B) Gigabit PRP with 2x single-mode LC 10km Conformal Coating 1x Pair (A/B) Gigabit PRP with 2x single-mode LC 10km Conformal Coating 6GK6050-0ML20-0PR1 6GK6050-0RL20-0PR1 Patch Panel and Cables Panels for MX500RE PRP module 6GK6050-0AR00-2PR0 RUGGEDCOM MX5000REPN LM MPRP 45

54 Chapter 8 Network Redundancy Modules RUGGEDCOM Modules 46 RUGGEDCOM MX5000REPN LM MPRP

55 RUGGEDCOM Modules Chapter 9 Blank Modules Blank Modules The following blank modules are available for the RUGGEDCOM MX5000RE. IMPORTANT! Blank modules should be installed in empty slots to prevent the ingress of dirt or debris in the chassis. CONTENTS Section 9.1, RUGGEDCOM MX5000REPN PS XX Section 9.2, RUGGEDCOM MX5000REPN LM XX 47

56 Chapter 9 Blank Modules RUGGEDCOM Modules Section 9.1 RUGGEDCOM MX5000REPN PS XX The RUGGEDCOM MX5000REPN PS XX is a blank module designed to occupy empty power supply module slots in the RUGGEDCOM MX5000RE chassis. Figure 22: RUGGEDCOM MX5000REPN PS XX Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Ordering Information Description Article Numbers Power Supply Blank Module, Full Panel 6GK6050-0RL10-0AA1 48 RUGGEDCOM MX5000REPN PS XX

57 RUGGEDCOM Modules Chapter 9 Blank Modules Section 9.2 RUGGEDCOM MX5000REPN LM XX The RUGGEDCOM MX5000REPN LM XX is a blank module designed to occupy empty line module slots in the RUGGEDCOM MX5000RE chassis. Figure 23: RUGGEDCOM MX5000REPN LM XX Installing the Module For information about installing this module, refer to the Installation Guide for the RUGGEDCOM MX5000RE. Ordering Information Description Article Numbers Blank Module 6GK6050-0RL20-0AA1 RUGGEDCOM MX5000REPN LM XX 49

58 Chapter 9 Blank Modules RUGGEDCOM Modules 50 RUGGEDCOM MX5000REPN LM XX