Multi Function POS SP-7262

Transcription

1 Multi Function POS SP-7262 User s Manual Edition: Jun 2015 Version 0.9

2 PREFACEE Federal Communications Commission (FCC) This equipment has been tested t andd found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCCC Rules. These T limits are designed to provide reasonable protection against harmful interferencee in a residential installation. This equipment generates, uses and can radiatee radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio orr televisionn reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following f measures: Reorient or relocate the receiving antenna. Increasee the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Declaration of Conformity These devices comply with part 15 of the FCC Rules. Operationn is subject to the following two conditions: 1. Thesee devices may not cause harmful interference. 2. Thesee devices must accept any interference received, including interference that may cause undesired operation. Lithium Battery Replace ement To avoid possible danger of explosion, ensuree correct polarity when changing the lithium battery. Replace only with the same or equivalent type recommended by the manufacturer. WEEEE (Waste from Electrical and Electronicc Equipment) The WEEE wheeled bin symbol on the product or on its packaging indicates that the product must not be disposed of with other waste. It should be the user s responsibility to dispose of their waste equipment by handing it over to an approved location for the recycling of waste electrical and electronic equipment. For more information about where to send your waste equipment for recycling, please contact your local city office, your household d waste disposal service or where you purchased the product. SP 7262 Multi Function POS II

3 Disclaimer PREFACE The material in this document is for information purpose and is subject to change without prior notice. APPOSTAR has made every effort to ensure that this user s manual is accurate and complete. However, no liability is assumed for any errors and omissions that may have occurred. Nor are any liability assumed for any damages resulting from the use of this product and the information contained in this document. APPOSTAR reserves the right to make improvements to this publication from time to time in the contents hereof without obligation of the manufacturer to notify any person of such revision or changes. Copyright This work is copyrighted. Reproduction or retransmission of this documentation, in whole or in part, without prior written permission from the manufacture is a violation of copyright law APPOSTAR Technology Co., Ltd. All rights reserved. Trademark Recognition 1. Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp. 2. Intel is a registered trademark of Intel International Inc. 3. Other software or product names used in this manual are the properties of their respective owners and are acknowledged. III SP-7262 Multi Function POS

4 PREFACE Important Safety Instructions Failure to observe these safety instructions may cause bodily injury, or damage to the product. Read these instructions carefully and keep this user s manual in an accessible location for future reference. The product may cause a fire or electric shock when it is used improperly. Observe the above safety measures at all times. If the product is damaged, immediately turn off the power and disconnect the power cord. Contact your dealer for assistance. 1. Do not plug in or unplug the power cord with wet hands. 2. Do not plug the product into an AC outlet with the incorrect voltage. (Be sure to use a voltage that is between AC 100V~240V) 3. Do not plug several products into one multi-outlet. 4. Do not apply pressure to the power cord or place heavy objects on it. 5. Immediately stop using the product if it emits strange noise, odor, or smoke. 6. Do not use aerosol sprayers containing flammable gas inside or around the product. 7. Do not allow foreign objects or liquids to enter the product, or serious damage may result. 8. Do not place the product on an unstable surface. The product may cause a fire if it is dropped, damaged, or broken. The following instructions will help you to make better use of this product. 1. Keep the machine away from locations subject to high humidity, dust, or temperatures that exceed the specification. (Refer to SEC. 1.4 Specification) 2. Clean the product only by using a dry cloth or a cloth soaked with detergent. Never use thinner or other volatile solvents for cleaning. 3. At the end of the day, clean and inspect the exterior of the machine after the machine is powered off. 4. Use only specified accessories. 5. Do not expose the accessories directly to sunlight, high temperatures, humidity, dust, or gas. 6. Do not place heavy objects on top of the product or lean them against the product. These items may fall down and cause injury. 7. Do not block the air vent of the product as this can cause heat accumulation inside the box machine and may cause a fire. SP 7262 Multi Function POS IV

5 Table of Contents CHAPTER 1 Product Overview Unpacking Appearance I/O Interface Specification... 6 CHAPTER 2 Hardware Installation Magnetic Stripe Reader (MSR) Installation... 7 CHAPTER 3 Software Installation Motherboard Driver Installation Peripheral Device Driver Installation... 9 CHAPTER 4 Board Setting Main Board Jumper Setting CHAPTER 5 INITIALIZING SCANNING BARCODES MAINTAINING CHAPTER 6 TROUBLESHOOTING APPENDIX General Scanner functionality USB Communication Decoding parameters Data formatting... 56

6 PRODUCT OVERVIEW CHAPTER 1 Product Overview Welcome The Multi Function POS series is the All-in-one POS Terminal which is conceptualized to save power consumption to meet the trend for green product. The features of Multi Function POS includes energy saving, s loww noise operation and highh performance value. The main board of Multi Function POS is skillfully embedded in the slim touch monitor. The compact and solidd stand gives you flexible working space arrangement. Up to five color options for the front panel are also providedd to match the mood of the operation environments. 1.1 Unpacking Confirm that all the following items are contained inn the carton. If any item is missing or damaged, contact the dealer from whom you y purchased the product. 1. POS Terminal Main Unit 2. Power Adapter 3. Power cord 4. Quick Reference Guide 5. Driver CD (User s Manual included) SP-7262 Multi Functionn POS 2

7 1.2 Appearance PRODUCT OVERVIEW Front View 15 LCD touch panel MSR (optional) / Attachable on both sides Scanner Rear View Left Side USB I/O Cover 3 SP-7262 Multi Function POS

8 PRODUCT OVERVIEW Side View Tilt angle 0~90 degree Scanner View Scanner angle 0~66 degree SP-7262 Multi Function POS 4

9 1.3 I/O Interface PRODUCT OVERVIEW No Port Description SPEAKER 1.5W integratedd x 2 DC Input 12V /2.5A DC Jack Cash Drawer Digital I/O with 12V (Digital I/O) RJ11 Connector (single/dual) COM3 COM1 Serial port with COM5 COM2 DB9/M and RJ-45 No Port Description Switch Power on/off VGA-OUT DB15/F VGA for second display PS/2 PS/2 Keyboard & Mouse Connector LAN RJ45 LAN Connector USB USB 2.0 A-type Connector x 4 Audio-in Line -in with Audio Jack Printer Port Parallel port withh DB25/ /F Connector Audio-out Line-out with Audio Jack DC Output O 12V / 2A DC Jack Storage HDD or SSD with removable bracket NOTE: To avoid confusion with the LAN port, the COMM 5 is protected with a lid. Remove the lid before use. With the removable HDD / SSD bracket, the HDD / SSD can be easily removed from the slot. 5 SP-7262 Multi Function POS

10 PRODUCT OVERVIEW 1.4 Specification System Main Board IAT CPU Intel Celeron 1037U 1.8 GHz Dual Core Chipset Intel NM70 Main Memory 1GB DDRIII RAM Display Size 15 TFT-LCD with Touch Panel Display Resolution 1024 x 768 Touch Panel 5 wire resistive touch HDD 2.5 SATA HDD 320G Expansion slot 1 x Mini PCIe OS Support POSReady 2009, POSReady7, Windows XP / XPE, Windows 7, Windows 8, Linux Power AC 100V ~240V / 60W Adapter I/O Interface Serial Port 4 x External COM Ports with 5V /12V selectable Cash Drawer Port 1 x RJ11 with DC 12V (Default) / 24V Keyboard Port 1 x PS/2 VGA Port 1 x VGA (DB15) Audio Port 1 x Line in, 1x Line out Speaker 2 x Integrated 1.5W Stereo Speaker Ethernet Port 1 x RJ45 10M / 100M / 1G Base-T USB Port 4 x USB 2.0 Type A, 5 x USB 2.0 Type A DC Output 1 x 12V / 2.5A Optional Peripheral Magnetic Card Reader ISO 7811 option 1 / 2 / 3 track Finger Print 512 dpi x 8 bit gray scale, Capture area: 14.6 x 18.1 mm i-button Dallas Key Wireless LAN b/g Customer Display VFD / LCD Customer Display Second Display TFT-LCD Display / non-touch Environment EMC & Safety CE/FCC Class A Operating Temperature 5 C ~ 40 C Storage Temperature -20 C ~ 60 C Operating Humidity 15%~80% RH Storage Humidity 20% ~90% RH Laser Safety IEC (1993) Class I, U.S. 21CFR1040 Class IIa Mechanical Housing Color Black Construction ABS + SECC Dimension (W x D x H) 355 x 240 x 390 mm Weight N.W 6.7kg SP-7262 Multi Function POS 6

11 CHAPTER 2 Hardware Installation HARDWARE INSTALLATION Before starting any hardware configuration, ensure that the system is powered off and the power cord is disconnected to prevent possible damage to the product. 2.1 Magnetic Stripe Reader (MSR) Installation An optional MSR can be installed on both right and left side of SP By default, the MSR is installed on the right side. Step 1 Remove the cover from the MSR extension slot. Step 2 Connect the MSR cable correctly. 7 SP-7262 Multi Function POS

12 SOFTWARE INSTALLATION CHAPTER 3 Software Installation This chapter describes the driver requirements and how to install the drivers from the driver CD. All step-by-step procedures described below are for Windows XP and similar on all other Microsoft Windows platforms. Insert the driver CD into your CD ROM drive. Windows will automatically detect it and the Appostar Driver Installer appears on the screen. If not, locate the Setup.exe file at CD:\ and double click it to execute the one step driver installation. Follow the on screen instructions to complete the installation. 3.1 Motherboard Driver Installation a. Click Install Motherboard Drivers. Select your model name and click Next to continue. b. Click Drivers icon on the upper left corner to continue. c. Select the Drivers option, including Chipset, Graphics, and LAN. Click Install to continue. d. Select Yes to reboot system. SP-7262 Multi Function POS 8

13 3.2 Peripheral Device Driver Installation Touch Panel Driver Installation SOFTWARE INSTALLATION a. Click Touch Panel. b. Click Next on the Welcome screen to continue. c. Uncheck the Install PS/2 interface driver option. Click Next to continue. d. Select the Install RS232 interface driver option. Click Next to continue. e. Select the None option and click Next to continue. f. Select the Support Multi Monitor System option. Click Next to continue. 9 SP-7262 Multi Function POS

14 SOFTWARE INSTALLATION g. Select the Destination Folder or use the default one listed. h. Type a Folder name or use the default one listed. Click Next to continue. i. A progress window appears. Please wait. j. Click Yes. The installation completes in seconds. SP-7262 Multi Function POS 10

15 INITIALIZING CHAPTER 4 Board Setting 4.1 Main Board Jumper Setting NOTE: represents the 1 st pin. JCMOS1: Clear CMOS Jumper Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the mainboard. 11 SP-7262 Multi Function POS

16 INITIALIZING Serial Port Connectors & Headers: JPC4: Serial Port Voltage Switch Jumper for JCOM4 JPC3/JPC5/JPC6: Serial Port Voltage Switch Jumpers for JCOM3/JCOM5/JCOM6 JP2: Voltage Switch Jumper for Cash Draw Connector This jumper is for controlling the Pin4 of RJ11 (JRJ11) to switch 12V or 24V. SP-7262 Multi Function POS 12

17 INITIALIZING Serial Port Voltage Switch for COM1 / COM2 through BIOS setting Enter BIOS / Advanced / F81866 Super IO Configuration / UART1 RI Function for COM1 or UART2 RI Function for COM2 13 SP-7262 Multi Function POS

18 INITIALIZING CHAPTER 5 INITIALIZING When using this scanner for the first time, you need to initialize the communication. parameters first. Follow the steps below to initialize: 1. Power up POS. 2. Initialize the communication parameters by scanning the programming barcode 1.1 and 1.3 on the APPENDIX (A. Change Scanner Settings). NOTE The procedure is required only once. However, when changing the cable from one type to another, you need to perform the procedure again. 3. In USB mode, the scanner defaults to Keyboard Emulation Mode. This scanner transmits the data in International Keyboard layout (ALT-method) for communication. NOTE The USB must be directly connected to the host-usb port and not through an (un-powered) USB hub. 5.1 SCANNING BARCODES This scanner is an omni-directional presentation scanner featuring a 6 directional scan field with a 24-line scan pattern. Barcode labels can easily be read by presenting them to the scanner. NOTE Since this scanner is a presentation scanner, best results are obtained if the barcode is moved towards the scanner. SP-7262 Multi Function POS 14

19 INITIALIZING 5.2 MAINTAINING This scanner requires little maintenance. Only occasional cleaning of the scanner window is necessary to remove dirt and fingerprints. Cleaning can be performed during operation with a non-abrasive glass spray cleaner and a soft lint-free cloth. 15 SP-7262 Multi Function POS

20 INITIALIZING CHAPTER 6 TROUBLESHOOTING This section contains information on solving problems you may encounter when using the scanner. If troubles occur, take a moment to read the information in this section. However, before referring to the diagnostic tips ensure that the scanner is installed as described in Chapter 2 and that all cables are properly connected. Problem Diagnostic Tips The scanner window is dirty. Clean the scanner window as described in section 5.2. The scanner is on but a barcode cannot be read. The scanner does not accept more than two or three barcodes. A barcode is read by the scanner but not accepted by the host system. USB communication is not working. The presented barcode type is not enabled. Select the barcode type with the Configuration Guide. The scanner is disabled by the host. The barcode type you presented to the scanner is not supported by this scanner. There is no proper handshaking with the host system. Switch the host system on and check connection and communication settings. The communication cable is not connected to the serial port of your host system. Refer to the manual of your host system to locate the serial port. The communication settings of the host and scanner do not match. Ensure that the setting values for both devices are the same. For proper adjustment values, refer to the Configuration Guide. The communication cable does not suit your host system. Contact your supplier for the correct communication cable. The data format is not supported by the software running on the host system. In case of KB emulation you can select various keyboard languages or the universal Alt-input-method (default). You may want to try programming barcodes from section 3.4 on the Configuration Guide. In case of KB emulation in combination with the Alt-input method, check that Num-Lock of your keyboard is on. In MS-windows environment, verify with the device manager that the HID (Human Interface Device) is installed for the scanner. Check that the scanner and the host system both expect the same USB protocol (KB emulation, RS232 emulation or IBM POS protocol). See the Configuration Guide for setup codes and reset the scanner after making any changes. When using a standard-usb cable, the scanner defaults to the USB KB emulation protocol with ALT-method character transmission. When using USB plus power cable (with the green connector), the scanner defaults to USB-IBM-POS protocol for tabletop scanners. These settings are restored after programming back to default using the Configuration Guide. SP-7262 Multi Function POS 16

21 APPENDIX Change Scanner Settings In order to change the scanner settings please follow the sequence below: 1. OPEN the scanner Programming Mode by scanning code CHANGE SCANNER SETTINGS by scanning any of the codes 2.1.x to 10.x.x. 3. CLOSE the scanner Programming Mode by scanning code 1.1. Reading the OPEN/CLOSE code 1.1 gives a double tone beep (Low High). An example: For changing the baudrate to 4800 the following codes must be scanned successively: After reading a valid barcode in Programming mode the scanner will give a High beep. The scanner will generate a Low beep after receiving an unexpected code. Reading a code, for example a predefined ASCII character, directly after entering the Programming Mode, is not allowed and the scanner will not accept this data. At any moment (in Programming Mode) you can scan code 1.2 to close the programming mode without update, or code 1.3 to return to default setting. SP 7262 Multi Function POS 17

22 Factory default settings SLEEP MODE DEFAULT Sleep mode After 10 minutes RS232 COMMUNICATION DEFAULT Baudrate 9600 Parity None Data bits 8 Stop bits 2 RTS/CTS Off Postamble <CR> KEYBOARD WEDGE COMMUNICATION DEFAULT Terminal type PC/AT Keyboard International (ALT Method) + Inter character delay 2 msec ++ Postamble Enter (alpha numeric) USB COMMUNCATION DEFAULT Mode USB Keyboard Emulation DECODER SELECTION DEFAULT EAN/UPC On (Add-On Off) Code 128/EAN 128 On Code 39 On Code 32 Off Codabar Off Interleaved 2/5 Off MSI Plessey Off Code 93 Off ISBN Off ISSN Off GS1 DataBar Off GS1 DataBar Expanded Off DECODER CONFIGURATION DEFAULT Min. length Interleaved 2/5 8 CODE IDENTIFIERS DEFAULT Code identifiers Off NOTE: + In Asian Mode, it is set at US Keyboard. ++ In Asian Mode, it is set at 0 msec. SP-7262 Multi Function POS 18

23 Default message format CODE MESSAGE FORMAT EAN13 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11D12 D13 EAN8 D1 D2 D3 D4 D5 D6 D7 D8 UPCA D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11D12 UPCE 0 D1 D2 D3 D4 D5 D6 Code 128 D1 - Dx EAN 128 ]C1 D1 - Dx Code 39 D1 - Dx Code 32 D1 - Dx Codabar D1 - Dx Interleaved 2/5 D1 - Dx MSI Plessey D1 - Dx Code 93 D1 - Dx ISBN D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 ISSN D1 D2 D3 D4 D5 D6 D7 D8 GS1 DataBar D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11D12 D13 GS1 DataBar DD11-4D74 (numeric) D1- D42 (alphanumeric) Expanded Important: Please note that EAN/UPC codes with Add-On are transmitted without a separator. Programming flow chart CHANGE SCANNER SETTINGS OPEN PROGRAMMING MODE BY SCANNING CODE 1.1 CHANGE SCANNER SETTINGS BY SCANNING CODE 2.1.x 10.x.x CLOSE PROGRAMMING MODE BY SCANNING CODE 1.1 SAVE AND EXIT 19 SP-7262 Multi Function POS

24 1. General 1.1 OPEN PROGRAMMING MODE OR CLOSE PROGRAMMING MODE WITH UPDATE CLOSE PROGRAMMING MODE WITHOUT UPDATE 1.2 SP-7262 Multi Function POS 20

25 1.3 RETURN TO FACTORY DEFAULT SETTINGS 1.3 Use this code to return to the original factory default setting. Important: Programming Mode is closed after scanning this code. 1.8 EMEA MODE 1.8 Note: For European, Middle East and African countries, read the following bar codes to set in EMEA mode SP-7262 Multi Function POS

26 1.9 ASIA MODE Note: For Asian and other countries (except European, Middle East and African countries), read the following bar codes to set in Asia mode FIRMWARE VERSION 1.15 Note: Output the firmware version by read the following bar codes: SP-7262 Multi Function POS 22

27 2. Scanner functionality 2.1 Speaker settings SPEAKER FERQUENCY Note: Repeat reading this bar code to obtain different tone SPEAKER VOLUME Note: Repeat reading this bar code to obtain different volume. 23 SP-7262 Multi Function POS

28 2.2 Sleep mode SLEEP MODE OFF Note: This setting will reduce the product life time SLEEP MODE AFTER 10 MINUTES (DEFAULT) SP-7262 Multi Function POS 24

29 2.2.3 SLEEP MODE AFTER 30 MINUTES SLEEP MODE AFTER 60 MINUTES SP-7262 Multi Function POS

30 2.3 Scanner timing SAME CODE DELAY 300MSEC SAME CODE DELAY 600MSEC SP-7262 Multi Function POS 26

31 3. USB Communication 3.1 USB SETTINGS For scanners with integrated USB-interface, you may activate this interface by connecting to appropriate communication cable. Depending on the firmware version of the scanner, various protocol versions may be possible: 1. USB Keyboard Emulation (default) 2. USB IBM fixed POS scanner 3. USB IBM handheld scanner emulation Important: Reset (re-power) the scanner after changing one of the options listed above USB KEYBOARD EMULATION (DEFAULT) USB IBM FIXED POS SCANNER SP-7262 Multi Function POS

32 3.1.3 USB IBM HANDHELD SCANNER EMULATION USB COMPORT EMULATION SP-7262 Multi Function POS 28

33 4. Decoding parameters 4.1 Decoder selection EAN/UPC ON + ADDON OFF (DEFAULT) EAN/UPC OFF + ADDON OFF SP-7262 Multi Function POS

34 4.1.3 EAN/UPC ON + ADDON ON Note: Important: Add-On codes are optional. The scanner will accept bar codes with or without Add-On. If the scanner reads an EAN/UPC code without Add-On, the scanner will look for a certain extra time for an Add-On. If this time has elapsed and no Add-On is found, the scanner will just send the EAN/UPC main code EAN/UPC + ADDON MANDATORY ON (FOR378/379/414/419/434/439/529/977) SP-7262 Multi Function POS 30

35 CODE 128/EAN 128 ON CODE 128/EAN 128 OFF SP-7262 Multi Function POS

36 CODE 39 ON CODE 39 FULL ASCII ON SP-7262 Multi Function POS 32

37 CODE 32 ON CODE 39/CODE 32 OFF SP-7262 Multi Function POS

38 CODABAR ON CODABAR OFF SP-7262 Multi Function POS 34

39 INTERLEAVED 2/5 ON It is mandatory to select a minimum code length using the appropriate bar code in paragraph 4.2 to prevent short reads INTERLEAVED 2/5 OFF SP-7262 Multi Function POS

40 MSI PLESSEY ON MSI PLESSEY OFF SP-7262 Multi Function POS 36

41 CODE 93 ON CODE 93 OFF SP-7262 Multi Function POS

42 ISBN ON ISBN OFF SP-7262 Multi Function POS 38

43 ISSN ON ISSN OFF SP-7262 Multi Function POS

44 GS1 DATABAR ON GS1 DATABAR OFF SP-7262 Multi Function POS 40

45 GS1 DATABAR EXPANDED ON GS1 DATABAR EXPANDED OFF SP-7262 Multi Function POS

46 GS1 DATABAR LIMITED ON GS1 DATABAR LIMITED OFFF SP-7262 Multi Functionn POS 42

47 4.2 Decoder configuration Programming flow chart for minimum length off bar code PROGRAMMING MINIMUM LENGTH OF BAR CODE SET MINIMUM LENGTH OF BAR CODE (SCAN CODE 4.2.1~ ) LENGTH (SCAN CODE ~ ) SAVE AND EXIT SET MIN. LENGTH CODE SET MIN. LENGTH CODE39 43 SP-7262 Multi Function POS

48 SET MIN. LENGTH CODABAR R SET MIN. LENGTH INTERLEAVED 2/ SP-7262 Multi Functionn POS 44

49 SET MIN. LENGTH MSI Plessey SET MIN. LENGTH CODE SP-7262 Multi Function POS

50 LENGTH = LENGTH = SP-7262 Multi Functionn POS 46

51 LENGTH = LENGTH = SP-7262 Multi Function POS

52 LENGTH = LENGTH = SP-7262 Multi Functionn POS 48

53 LENGTH = LENGTH = SP-7262 Multi Function POS

54 LENGTH = LENGTH = SP-7262 Multi Functionn POS 50

55 LENGTH = LENGTH = SP-7262 Multi Function POS

56 LENGTH = LENGTH = SP-7262 Multi Functionn POS 52

57 4.3 Japanese book code DISABLE 978/192 JAPANESEE BOOK CODE(DEFAULT) ENABLE 978/192 JAPANESE BOOK CODE SP-7262 Multi Function POS

58 4.3.5 ENABLE JAPANESE BOOK CODE SEPARATOR (DEFAULT) DISABLE JAPANESE BOOK CODE SEPARATOR SP-7262 Multi Functionn POS 54

59 4.3.7 OPEN PROGRAMMING JAPANESE BOOK CODE SEPARATOR (ONE CHARACTER) Note: Only one separator is available. To set Japanese book code separator, scan: ASCII code SP-7262 Multi Function POS

60 5. Data formatting 5.1 Preambles Programming sequence preambles The scanner can be programmed to output bar code data according to the following format: [PREAMBLE STRING BAR CODE DATA] The preamble string is limited to a maximum length of 3 characters. Use the chart on the next page to program the preamble string. Example: To send a <STX> in front of the bar code, scan successively (while in Programming Mode) Free programmable preambles : Open Programming mode <STX> Free programmable preambles : Close programming mode with update As a result, the scanner will give the following bar code data output: SP-7262 Multi Function POS 56

61 Programming flow chart preambles PROGRAMMMING PREAMBLE STRING OPEN PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES (SCAN CODE 5.1.1) SELECT PREAMBLE CHARACTER (SCAN CODE 10.1.X) Yes SAVE AND EXIT NUMBER OF PREAMBLE CHARACTERS = 3? NO MOREPREAMBLE CHARACTERS TO BE PROGRAMMED? Yes 57 NO SP-7262 Multi Function POS Yes SAVE PROGRAMMED DATA?

62 5.1.1 FREE PROGRAMMABLE PREAMBLES: OPEN PROGRAMMING MODE / CLOSE PROGRAMMING MODE WITHOUT UPDATE FREE PROGRAMMABLE PREAMBLES: CLOSE PROGRAMMING MODE WITH UPDATE SP-7262 Multi Function POS 58

63 Postambles Programming sequence preambles The scanner can be programmed to output bar code data according to the following format: [BAR CODE DATA] [POSTAMBLE STRING] The preamble string is limited to a maximum length of 3 characters. Use the chart on the next page to program the preamble string. Example: To send a <ETX>after of the bar code, scan successively (while in Programming Mode) Free programmable preambles : Open Programming mode <ETX> Free programmable preambles : Close programming mode with update As a result, the scanner will give the following bar code data output: 59 SP-7262 Multi Function POS

64 Programming flow chart preambles PROGRAMMMING PREAMBLE STRING OPEN PROGRAMMING MODE FREE PROGRAMMABLE PREAMBLES (SCAN CODE 5.2.5) SELECT PREAMBLE CHARACTER (SCAN CODE 10.1.X) Yes NUMBER OF PREAMBLE CHARACTERS = 3? NO SAVE SP-7262 AND Multi EXIT Function POS 60 MOREPREAMBLE CHARACTERS

65 Yes PREDEFINED POSTAMBLE = CR(DEFAULT) 61 SP-7262 Multi Function POS

66 PREDEFINED POSTAMBLE = LF PREDEFINED POSTAMBLE = CR + LF SP-7262 Multi Function POS 62

67 FREE PROGRAMMABLE POSTAMBLES: OPEN PROGRAMMING MODE / CLOSE PROGRAMMING MODE WITHOUT UPDATE SP-7262 Multi Function POS

68 5.2.6 FREE PROGRAMMABLE POSTAMBLES: CLOSE PROGRAMMING MODE WITH UPDATE Code identifiers Set message format with code identifiers A code identifier is a data string, giving information to the host system concerning the bar code type that has been read. After scanning code 5.3.1, the scanner is programmed to transmit data according to the following format: CODE CODE MESSAGE FORMAT EAN13 F D1 - D13 EAN8 FF D1 - D8 UPCA A D1 - D12 UPCE E 0 D1 - D6 Code 128 # D1 - Dx EAN 128 P ]C1 D1 - Dx Code 39 * D1 - Dx Code 32 * D1 - Dx Codabar % D1 - Dx Interleaved 2/5 i D1 - Dx MSI Plessey O D1 - Dx Code 93 L D1 - Dx ISBN F D1 - D10 ISSN F D1 - D8 GS1 DataBar U D1 - D14 GS1 DataBar Expanded W D1 - D74 (numeric) or D1 - D42 (alphanumeric) Important: Please note that the UPCE format will be changed. The scanner will transmit UPCE codes with leading zero and without check digit. To return to default format without code identifiers scan code SP-7262 Multi Function POS 64

69 5.3.1 SET MESSAGE FORMAT WITH CODE IDENTIFIERS APPENDIX SET MESSAGE FORMAT WITHOUT CODE IDENTIFIERS versions of preset code identifier are available. The comparison between default version 65 SP-7262 Multi Function POS

70 and Datalogic version is listed below. Default Datalogic EAN13 F F EAN8 FF FF UPCA A A UPCE E E Code 128 # # EAN 128 P Null(none) Code 39 * * Code 32 * p ITF 25 i l Codabar % % Code 93 L & MSI/PLESSY DataBar Omni-directional U R4 DataBar Limted V RL DataBar Expanded W RX Note: Scan code for Datalogic version. *Datalogic is the trade mark of Datalogic S.p.A. SP-7262 Multi Function POS 66

71 5.3.3 DEFAULT CODE IDENTIFIER APPENDIX DATALOGIC CODE IDENTIFIER Programming flow chart for setting codee identifier PROGRAMMING CODE IDENTIFIER 67 SP-7262 Multi Function POS

72 SET IDENTIFIER OF BAR CODE (SCAN CODE ~ ) ASCII CODE (SCAN CODE ~ ) EXIT PROGRAMMING IDENTIFIER WITH UPDATE (SCAN CODE ) SAVE AND EXIT SETTING IDENTIFIER EAN SETTING IDENTIFIER EAN SP-7262 Multi Functionn POS 68

73 SETTING IDENTIFIER UPCAA SETTING IDENTIFIER UPCE SP-7262 Multi Function POS

74 SETTING IDENTIFIER EAN SETTING IDENTIFIER CODE SP-7262 Multi Functionn POS 70

75 SETTING IDENTIFIER CODE SETTING IDENTIFIER CODE SP-7262 Multi Function POS

76 SETTING IDENTIFIER CODABAR SETTING IDENTIFIER INTERLEAVED 2/ SP-7262 Multi Functionn POS 72

77 SETTING IDENTIFIER MSI/ /PLESEY SETTING IDENTIFIER CODE SP-7262 Multi Function POS

78 EXIT PROGRAMMING FREE PROGRAMMABLE IDENTIFII ER WITH UPDATE EXIT PROGRAMMING FREE UPDATE PROGRAMMABLE IDENTIFII ER WITHOUT SP-7262 Multi Functionn POS 74

79 5.4 Code representation UPCA FORMAT TRANSMITTED AS UPCA (12 DIGITS) UPCA FORMAT TRANSMITTED AS EAN13 (WITHH LEADING ZERO) SP-7262 Multi Function POS

80 5.4.5 UPCA FORMAT UPCE TO UPCAA EXPANSION ON UPCA FORMAT UPCE TO UPCAA EXPANSION OFF SP-7262 Multi Functionn POS 76

81 5.4.7 UPCE FORMAT WITH LEADING ZERO UPCE FORMAT WITHOUT LEADING ZERO SP-7262 Multi Function POS

82 5.4.9 UPCE FORMAT WITH CHECK DIGIT UPCE FORMAT WITHOUT CHECK DIGIT SP-7262 Multi Function POS 78

83 EAN 128 CODE INDENTIFIER ]C1 ON EAN 128 CODE INDENTIFIER ]C1 OFF SP-7262 Multi Function POS

84 TRANSMITT EAN8 CHECKDIG GIT ON TRANSMITT EAN8 CHECKDIG GIT OFF SP-7262 Multi Functionn POS 80

85 TRANSMITT EAN13 CHECKDIGIT ON TRANSMITT EAN13 CHECKDIGIT OFF SP-7262 Multi Function POS

86 TRANSMITT UOCA CHECKDIG GIT ON TRANSMITT UPCA CHECKDIG GIT OFF SP-7262 Multi Functionn POS 82

87 EXPAND EAN8 TO UPCA ON EXPAND EAN8 TO UPCA OFF SP-7262 Multi Function POS

88 TRANSMITT FIRST DIGIT UPCA OFF TRANSMITT FIRST DIGIT UPCA ON SP-7262 Multi Functionn POS 84

89 TRANSMISSION OF THE CHECK CHARACTER AT CODE39 OFF TRANSMISSION OF THE CHECK CHARACTER AT CODE39 ON SP-7262 Multi Function POS

90 VERIFICATION OF THE CHECK CHARACTER AT A CODE39 OFF VERIFICATION OF THE CHECK CHARACTER AT A CODE39 ON SP-7262 Multi Functionn POS 86

91 TRANSMISSION OF THE CHECK CHARACTER AT CODABAR OFF TRANSMISSION OF THE CHECK CHARACTER AT CODABAR ON SP-7262 Multi Function POS

92 VERIFICATION OF THE CHECK CHARACTER AT A CODABAR OFF VERIFICATION OF THE CHECK CHARACTER AT A CODABAR ON SP-7262 Multi Functionn POS 88

93 TRANSMISSION OF THE CHECK DIGIT AT INTERLEAVED 2/5 OFF TRANSMISSION OF THE CHECK DIGIT AT INTERLEAVED 2/5 ON SP-7262 Multi Function POS

94 VERIFICATION OF THE CHECK DIGIT AT INTERLEAVEDD 2/5 OFFF VERIFICATION OF THE CHECK DIGIT AT INTERLEAVEDD 2/5 ON SP-7262 Multi Functionn POS 90

95 VERIFICATION MSI/PLESSEY CHECK DIGIT OFF O VERIFICATION MSI/PLESSEY CHECK DIGIT ON O SP-7262 Multi Function POS

96 TRANSMISSION OF THE CHECK DIGIT AT ISBN OFF TRANSMISSION OF THE CHECK DIGIT AT ISBN ON SP-7262 Multi Functionn POS 92

97 DO NOT TRANSMITT START/ /STOP AT CODE TRANSMITT START/ /STOP AT CODE SP-7262 Multi Function POS

98 DO NOT TRANSMIT START/STOP CODABAR SP-7262 Multi Functionn POS 94

99 B. Predefined ASCII characters SOH STX SP-7262 Multi Function POS

100 ETX EOT SP-7262 Multi Function POS 96

101 C. Special keys On the following pages you find some special key programming bar codes, related to KBW communication. These codes are also applicable in USB interface with USB keyboard emulation TAB ENTER (ALPHANUMERIC) SP-7262 Multi Function POS

102 ENTER (NUMERIC) SP-7262 Multi Function POS 98