Cisco HyperFlex HX240c M4 Node

Transcription

1 Spec Sheet Cisco HyperFlex HX240c M4 Node CISCO SYSTEMS PUBLICATION HISTORY 170 WEST TASMAN DR. SAN JOSE, CA, REV A.10 JANUARY 12,

2 CONTENTS OVERVIEW DETAILED VIEWS Chassis Front View Chassis Rear View BASE HX240c NODE STANDARD CAPABILITIES and FEATURES CONFIGURING the HX240c M4 Node STEP 1 VERIFY SKU STEP 2 SELECT RISER CARD (OPTIONAL) STEP 3 SELECT CPU(s) STEP 4 SELECT MEMORY STEP 5 SELECT DRIVE CONTROLLER SAS HBA (internal HDD/SSD/non-RAID support) STEP 6 SELECT HARD DISK DRIVES (HDDs) or SOLID STATE DRIVES (SSDs) STEP 7 SELECT PCIe OPTION CARD(s) STEP 8 ORDER GPU CARDS AND GPU POWER CABLES (OPTIONAL) STEP 9 ORDER POWER SUPPLY STEP 10 SELECT AC POWER CORD(s) STEP 11 ORDER TOOL-LESS RAIL KIT AND OPTIONAL REVERSIBLE CABLE MANAGEMENT ARM. 27 STEP 12 ORDER A TRUSTED PLATFORM MODULE (OPTIONAL) STEP 13 ORDER CISCO FLEXIBLE FLASH SD CARD MODULE STEP 14 SELECT OPERATING SYSTEM AND VALUE-ADDED SOFTWARE STEP 15 SELECT SERVICE and SUPPORT LEVEL OPTIONAL STEP - ORDER RACK(s) OPTIONAL STEP - ORDER PDU SUPPLEMENTAL MATERIAL Hyperconverged Systems Chassis Block Diagram CPUs and DIMMs Physical Layout Memory Population Rules DIMM Population Order Serial Port Details Upgrade and Servicing-Related Parts Adding an Additional CPU (with CPU heat sink) or Replacing CPUs Motherboard Lithium Battery Thermal Grease (with syringe applicator) for CPU to Heatsink Seal Air Baffle Replacement Kit CPU Heat Sink Cleaning Kit Riser Card Configuration and Options RACKS PDUs KVM CABLE TECHNICAL SPECIFICATIONS Dimensions and Weight Power Specifications Environmental Specifications Compliance Requirements

3 OVERVIEW OVERVIEW Cisco HyperFlex Systems unlock the full potential of hyperconvergence. The systems are based on an end-to-end software-defined infrastructure, combining software-defined computing in the form of Cisco Unified Computing System (Cisco UCS) servers; software-defined storage with the powerful Cisco HX Data Platform and software-defined networking with the Cisco UCS fabric that will integrate smoothly with Cisco Application Centric Infrastructure (Cisco ACI ). Together with a single point of connectivity and hardware management, these technologies deliver a preintegrated and adaptable cluster that is ready to provide a unified pool of resources to power applications as your business needs dictate. Figure 1 Cisco HX240c M4 Node (24-drive) Front View Rear View 3

4 DETAILED VIEWS DETAILED VIEWS Chassis Front View Figure 2 shows the 24-drive Cisco HX240c M4 Node (with front bezel removed). Figure 2 Chassis Front View (24-drive version) 1 2 HDD24 HDD23 HDD22 HDD21 HDD20 HDD19 HDD18 HDD17 HDD16 HDD15 HDD14 HDD13 HDD12 HDD11 HDD10 HDD09 HDD08 HDD07 HDD06 HDD05 HDD04 HDD03 HDD02 HDD Front Mount Drives 1 Up to 23 x 1.2 TB SAS HDDs (for data) 1 x 1.6 TB SATA SSD (for caching) 7 Temperature status LED 2 Operations panel buttons and LEDs 8 Power supply status LED 3 Power button/led 9 Network link activity LED 4 Unit Identification button/led 10 Pull-out asset tag 5 System status LED 11 KVM connector 6 Fan status LED Notes x 120 GB SATA SSD internal drive (on PCIe riser) is used for SDS logs (used with KVM cable that provides two USB 2.0, one VGA, and one serial connector) For more information about the KVM cable connection, see KVM CABLE, page 52. 4

5 DETAILED VIEWS Chassis Rear View Figure 3 shows the external features of the rear panel. Figure 3 Chassis Rear View PCIe 03 PCIe 02 PCIe 06 PCIe 05 PSU PCIe 01 mlom PCIe 04 PSU PCIe riser 1 (slots 1, 2, 3) 7 Serial connector (RJ-45) 1 2 PCIe riser 2 (slots 4, 5, 6) 8 Two embedded (on the motherboard) Intel i350 GbE Ethernet controller ports (LAN1, LAN2) 3 Power supplies (DC power supplies shown) 9 VGA video port (DB-15 connector) 4 Modular LAN-on-motherboard (mlom) card slot Notes For serial port pinout details, see Serial Port Details, page Rear Unit Identification button/led 5 USB 3.0 ports (two) 11 Grounding-lug holes (for DC power supplies) 6 1-Gbps dedicated management port 5

6 BASE HX240c NODE STANDARD CAPABILITIES and FEATURES BASE HX240c NODE STANDARD CAPABILITIES and FEATURES Table 1 lists the capabilities and features of the base node. Details about how to configure the node for a particular feature or capability (for example, number of processors, disk drives, or amount of memory) are provided in CONFIGURING the HX240c M4 Node, page 8. Table 1 Capabilities and Features Capability/Feature Chassis CPU Chipset Memory Multi-bit Error Protection Embedded NIC Expansion slots Video Internal storage devices Cisco Flexible Flash drives Description Two rack unit (2RU) chassis Two Intel Xeon E v3 or v4 series processor family CPUs Intel C610 series chipset 24 slots for registered ECC DIMMs (RDIMMs) Supports multi-bit error protection. Two embedded (on the motherboard) Intel i350 GbE ports, supporting the following: Pre-Execution Boot (PXE boot) iscsi boot Checksum and segmentation offload NIC teaming Up to six PCIe slots (on two riser cards) Riser 1 (PCIe slots 1, 2, and 3), controlled by CPU 1 Riser 2 (PCIe slots 4, 5, and 6), controlled by CPU 2. If GPU is ordered, it goes into slot 5. Dedicated disk controller slot (see Figure 7 on page 39) An internal slot is reserved for use by the Cisco 12 Gbps Modular SAS HBA. The Cisco Integrated Management Controller (CIMC) provides video using the Matrox G200e video/graphics controller: Integrated 2D graphics core with hardware acceleration DDR2/3 memory interface supports up to 512 MB of addressable memory (8 MB is allocated by default to video memory) Supports display resolutions up to 1920 x Hz High-speed integrated 24-bit RAMDAC Single lane PCI-Express host interface running at Gen 1 speed Drives are installed into front-panel drive bays that provide hot-pluggable access. Small Form Factor (SFF) drives. Up to TB front-mounting SAS HDDs (for data) One 1.6 TB front-mounting SATA SSD (for caching) One 120 GB internal SATA SSD (for SDS logs) The system supports two internal 64 GB Cisco Flexible Flash drives (SD cards). The SD cards are mirrored to each other and are used for booting. 6

7 BASE HX240c NODE STANDARD CAPABILITIES and FEATURES Capability/Feature Interfaces Rear panel Power subsystem Modular LAN on Motherboard (mlom) slot WoL Front Panel One DB15 VGA connector One RJ45 serial port connector Two USB 3.0 port connectors One RJ-45 10/100/1000 Ethernet management port, using Cisco Integrated Management Controller (CIMC) firmware Two Intel i350 embedded (on the motherboard) GbE LOM ports One flexible modular LAN on motherboard (mlom) slot that accommodates the Cisco UCS VIC1227 VIC MLOM - Dual Port 10Gb SFP+ interface card. Two PCIe 3.0 slots Front panel One KVM console connector (supplies two USB 2.0 connectors, one VGA DB15 video connector, and one serial port (RS232) RJ45 connector) Up to two of the following hot-swappable power supplies: 650 W (AC) 930 W (DC) 1200 W (AC) 1400 W (AC) One power supply is mandatory; one more can be added for redundancy. The mlom slot accommodates the following card: Cisco VIC 1227 Virtual Interface Cards The 1-Gb Base-T Ethernet LAN ports support the wake-on-lan (WoL) standard. A front panel controller provides status indications and control buttons ACPI This system supports the advanced configuration and power interface (ACPI) 4.0 standard. Fans Chassis: Six hot-swappable fans for front-to-rear cooling Storage controller Cisco 12 Gbps Modular SAS HBA with internal SAS connectivity Integrated management processor Description Supports up to 23 front-mount HDDS (for data), one front-mount SSD (for caching) and one internal SSD drive (for SDS logs) Plugs into a dedicated internal disk controller slot No RAID support Baseboard Management Controller (BMC) running Cisco Integrated Management Controller (CIMC) firmware. Depending on your CIMC settings, the CIMC can be accessed through the 1-GbE dedicated management port, the 1-GbE LOM ports, or a Cisco virtual interface card (VIC). 7

8 CONFIGURING the HX240c M4 Node CONFIGURING the HX240c M4 Node For the most part, this system comes with a fixed configuration. Follow these steps to see or change the configuration of the HX240c M4 Node: STEP 1 VERIFY SKU, page 9 STEP 3 SELECT CPU(s), page 11 STEP 4 SELECT MEMORY, page 14 STEP 5 SELECT DRIVE CONTROLLER, page 18 STEP 6 SELECT HARD DISK DRIVES (HDDs) or SOLID STATE DRIVES (SSDs), page 19 STEP 7 SELECT PCIe OPTION CARD(s), page 20 STEP 8 ORDER GPU CARDS AND GPU POWER CABLES (OPTIONAL), page 21 STEP 10 SELECT AC POWER CORD(s), page 24 STEP 11 ORDER TOOL-LESS RAIL KIT AND OPTIONAL REVERSIBLE CABLE MANAGEMENT ARM, page 27 STEP 12 ORDER A TRUSTED PLATFORM MODULE (OPTIONAL), page 28 STEP 13 ORDER CISCO FLEXIBLE FLASH SD CARD MODULE, page 29 STEP 14 SELECT OPERATING SYSTEM AND VALUE-ADDED SOFTWARE, page 30 STEP 15 SELECT SERVICE and SUPPORT LEVEL, page 31 OPTIONAL STEP - ORDER RACK(s), page 35 OPTIONAL STEP - ORDER PDU, page 36 8

9 CONFIGURING the HX240c M4 Node STEP 1 VERIFY SKU Verify the product ID (PID) from Table 2. Table 2 PID of the HX240c M4 Node Product ID (PID) HX240C-M4SX Description HX240c M4 Node, with two CPUs, memory, 23 HDDs, two SSDs, two power supplies, two SD cards, one VIC 1227 mlom card, no PCIe cards, and no rail kit The HX240c M4 Node: Includes two power supplies, two CPUs, memory, hard disk drives (HDDs), solid-state drives (SSDs), VIC 1227 mlom card, and SD cards Does not include rail kit or plug-in PCIe cards. NOTE: Use the steps on the following pages to see or change the configuration of the system. 9

10 CONFIGURING the HX240c M4 Node STEP 2 SELECT RISER CARD (OPTIONAL) There is one optional riser card, riser card 2. Order one riser card 2 from Table 3. Riser card 2 is the one on the right when viewed from the back of the server, and provides slots 4, 5, and 6. Table 3 Riser 2 Options Product ID (PID) Description UCSC-PCI-2-C240M4 PCIe Riser Board (Riser 2) for HXC240c M4 (3 slots: 2x8 and 1x16) NOTE: If no riser is selected, a riser blanking panel will be installed. You will not be able to install any PCIe cards without a riser selected For additional details, see Riser Card Configuration and Options, page

11 CONFIGURING the HX240c M4 Node STEP 3 SELECT CPU(s) The standard CPU features are: Intel Xeon E v3 or v4 series processor family CPUs Intel C610 series chipset Cache size of up to 55 MB Select CPUs The available CPUs are listed in Table 4. Table 4 Available Intel CPUs Highest Product ID (PID) Clock Cache DDR4 DIMM Intel Power Freq Size Cores QPI Clock Number (W) (GHz) (MB) Support (MHz) 1 E v4 Series Processor Family CPUs UCS-CPU-E52699E E v GT/s 2400 UCS-CPU-E52698E E v GT/s 2400 UCS-CPU-E52697AE E5-2697A v GT/s 2400 UCS-CPU-E52697E E v GT/s 2400 UCS-CPU-E52695E E v GT/s 2400 UCS-CPU-E52690E E v GT/s 2400 UCS-CPU-E52683E E v GT/s 2400 UCS-CPU-E52680E E v GT/s 2400 UCS-CPU-E52667E E v GT/s 2400 UCS-CPU-E52660E E v GT/s 2400 UCS-CPU-E52650E E v GT/s 2400 UCS-CPU-E52650LE E5-2650L v GT/s 2400 UCS-CPU-E52640E E v GT/s 2133 UCS-CPU-E52630E E v /0 GT/s 2133 UCS-CPU-E52630LE E5-2630L v GT/s 2133 UCS-CPU-E52620E E v GT/s 2133 UCS-CPU-E52609E E v GT/s 1866 UCS-CPU-E52658E E v GT/s

12 CONFIGURING the HX240c M4 Node Table 4 Available Intel CPUs (continued) Product ID (PID) Intel Number E v3 Series Processor Family CPUs Clock Freq (GHz) Power (W) Cache Size (MB) Cores UCS-CPU-E52699D E v GT/s 2133 UCS-CPU-E52698D E v GT/s 2133 UCS-CPU-E52697D E v GT/s 2133 UCS-CPU-E52695D E v GT/s 2133 UCS-CPU-E52690D E v GT/s 2133 UCS-CPU-E52683D E v GT/s 2133 UCS-CPU-E52680D E v GT/s 2133 UCS-CPU-E52670D E v GT/s 2133 UCS-CPU-E52667D E v GT/s 2133 UCS-CPU-E52660D E v GT/s 2133 UCS-CPU-E52658D E v GT/s 2133 UCS-CPU-E52650D E v GT/s 2133 UCS-CPU-E52650LD E5-2650L v GT/s 2133 UCS-CPU-E52640D E v GT/s 1866 UCS-CPU-E52630D E v GT/s 1866 UCS-CPU-E52630LD E5-2630L v GT/s 1866 Notes If higher or lower speed DIMMs are selected than what is shown in the table for a given CPU, the DIMMs will be clocked at the lowest common denominator of CPU clock and DIMM clock. QPI Highest DDR4 DIMM Clock Support (MHz) 1 12

13 CONFIGURING the HX240c M4 Node Approved Configurations (1) 2-CPU Configurations: Caveats Select two identical CPUs from any one of the rows of Table 4 on page 11. You must select two identical processors. For optimal performance, select DIMMs with the highest clock speed for a given processor (see Table 4 on page 11). If you select DIMMs whose speeds are lower or higher than that shown in the tables, suboptimal performance will result. 13

14 CONFIGURING the HX240c M4 Node STEP 4 SELECT MEMORY The standard memory features are: DIMMs Clock speed: 2400 and 2133 MHz Ranks per DIMM: 1, 2, 4, or 8 Operational voltage: 1.2 V Registered ECC DDR4 DIMMs (RDIMMs), load-reduced DIMMS (LR-DIMMs), or thru-silicon-via DIMMs (TSV-DIMMs). Memory is organized with four memory channels per CPU, with up to three DIMMs per channel, as shown in Figure 4. Figure 4 HX240c M4 Mode Memory Organization Slot 1 Slot 2 Slot 3 A1 A2 A3 Slot 3 E3 Slot 2 Slot 1 E2 E1 Chan A Chan E B1 B2 B3 F3 F2 F1 Chan B Chan F C1 C2 C3 CPU 1 CPU 2 G3 G2 G1 Chan C Chan G D1 D2 D3 H3 H2 H1 Chan D Chan H 24 DIMMS 1.5 TB maximum memory (with 64 GB DIMMs) 4 memory channels per CPU, up to 3 DIMMs per channel 14

15 CONFIGURING the HX240c M4 Node Select DIMMs Select the desired DIMMs from Table 5. Table 5 Available DDR4 DIMMs Product ID (PID) PID Description Voltage Ranks/ DIMM DIMM Options 2400-MHz DIMM Options UCS-ML-1X644RV-A 64 GB DDR MHz LRDIMM/PC /quad rank/x4 1.2 V 4 UCS-MR-1X322RV-A 32GB DDR MHz RDIMM/PC /dual rank/x4 1.2 V 2 UCS-MR-1X161RV-A 16GB DDR MHz RDIMM/PC /single rank/x4 1.2 V MHz DIMM Options UCS-MR-1X648RU-A 64 GB DDR MHz TSV-RDIMM/PC /octal rank/x4 1.2 V 8 UCS-MR-1X322RU-A 32GB DDR MHz RDIMM/PC /dual rank/x4 1.2 V 2 UCS-MR-1X162RU-A 16GB DDR MHz RDIMM/PC /dual rank/x4 1.2 V 2 Approved Configurations (1) 2-CPU configuration: Select either 8 or 12 identical DIMMs per CPU (16 or 24 total identical DIMMs). Refer to Memory Population Rules, page 42, for more detailed information. NOTE: System performance is optimized when the DIMM type and quantity are equal for both CPUs, and when all channels are filled equally across the CPUs in the system. 15

16 CONFIGURING the HX240c M4 Node Caveats System speed is dependent on how many DIMMs are populated per channel and the CPU DIMM speed support. See Table 6 for details. Table 6 DIMM Memory Speeds with Different CPUs DIMM Speed DPC 1866-MHz Capable CPU RDIMM (DR) 2133-MHz Capable CPU RDIMM (DR) 2133 DIMM 1 3 DPC (32 GB RDIMMs and 16 GB DIMMs) 2 DPC DPC Notes MHz DIMMs are the only offered and supported DIMMs for the HX220c M4 Node. Table MHz DIMM Memory Speeds with Different v4 CPUs DIMM and CPU Frequencies DPC LRDIMM (QRx4) - 64 GB RDIMM (2Rx4) - 32 GB RDIMM (SRx4) - 16 GB 1.2 V 1.2 V 1.2 V DIMM = 2400 MHz CPU = 2400 MHz 1DPC 2400 MHz 2400 MHz 2400 MHz 2DPC 2400 MHz 2400 MHz 2400 MHz 3DPC 2133 MHz 1866 MHz 2133 MHz DIMM = 2400 MHz CPU = 2133 MHz 1DPC 2133 MHz 2133 MHz 2133 MHz 2DPC 2133 MHz 2133 MHz 2133 MHz 3DPC 1866 MHz 1866 MHz 1866 MHz DIMM = 2400 MHz CPU = 1866 MHz 1DPC 1866 MHz 1866 MHz 1866 MHz 2DPC 1866 MHz 1866 MHz 1866 MHz 3DPC 1866 MHz 1600 MHz 1600 MHz The HX240c M4 Node supports the following memory reliability, availability, and serviceability (RAS) modes: Independent Channel Mode Lockstep Channel Mode Below are the system level RAS Mode combination limitations: Mixing of Independent and Lockstep channel mode is not allowed per platform. DIMMs for CPU 1 and CPU 2 must always be configured identically. 16

17 CONFIGURING the HX240c M4 Node Non-ECC DIMMs are not supported. Pairs of DIMMs (A1/B1, A2/B2, etc) MUST be the exact same (same PID, rev, DIMM loading order) Cisco memory from previous generation systems (DDR3) is not compatible with this system For more information regarding memory, see CPUs and DIMMs, page

18 CONFIGURING the HX240c M4 Node STEP 5 SELECT DRIVE CONTROLLER SAS HBA (internal HDD/SSD/non-RAID support) Choose the following SAS HBA for internal drive connectivity (non-raid): Cisco 12 Gbps Modular SAS HBA, which plugs into a dedicated RAID controller slot. Select Controller Options Select the following: Cisco 12 Gbps Modular SAS HBA (see Table 8) Table 8 Hardware Controller Options Product ID (PID) Controllers for Internal Drives PID Description Note that the following Cisco 12Gbps Modular SAS HBA controller is factory-installed in the dedicated internal slot. UCSC-SAS12GHBA Cisco 12 Gbps Modular SAS HBA Supports up to 24 internal SAS HDDs and SAS/SATA SSDs No RAID functionality. Ideal for SDS (Software Defined Storage) applications. It is also ideal for environments demanding the highest IOPs (for external SSD attach), where a RAID controller can be an I/O bottleneck. Approved Configurations The Cisco 12 Gbps Modular SAS HBA supports up to 24 internal drives with non-raid support. 18

19 CONFIGURING the HX240c M4 Node STEP 6 SELECT HARD DISK DRIVES (HDDs) or SOLID STATE DRIVES (SSDs) The standard disk drive features are: 2.5-inch small form factor Hot-pluggable Drives come mounted in sleds Select Drives The available drives are listed in Table 9. Table 9 Available Hot-Pluggable Sled-Mounted HDDs and SSDs Product ID (PID) HDD Data Drive PID Description Drive Type Capacity UCS-HD12TB10K12G 1.2 TB 12G SAS 10K RPM SFF HDD SAS 1.2 TB SATA SSD Caching Drive UCS-SD16TB12S3-EP 1.6 TB 2.5 inch Enterprise Performance 6G SATA SSD (3X endurance) SATA 1.6 TB SATA SSD SDS Logs Drive UCS-SD120GBKS4-EB 120 GB 2.5 inch Enterprise Value 6G SATA SSD SATA 120 GB Approved Configurations (1) Cisco 12 Gbps Modular SAS HBA Caveats Select the following drives: Up to 23 front-mount 1.2 TB 12G SAS 10K RPM SFF HDD data drives (UCS-HD12TB10K12G) One front-mount 1.6 TB 2.5 inch Enterprise Performance 6G SATA SSD caching drive (UCS-SD16TB12S3-EP) One internal 120 GB 2.5 inch Enterprise Value 6 G SATA SSD SDS logs drive (UCS-SD120GBKS4-EB) See SELECT DRIVE CONTROLLER, page 18 for more details. You must choose up to 23 HDDs for data, one SSD caching drive, and one SATA SSD SDS logs drive. 19

20 CONFIGURING the HX240c M4 Node STEP 7 SELECT PCIe OPTION CARD(s) The standard PCie card offerings is: Modular LAN on Motherboard (mlom) Select PCIe Option Card The available PCIe option card is listed in Table 10. Table 10 Available PCIe Option Cards Product ID (PID) PID Description Card Height Modular LAN on Motherboard (mlom) 1 UCSC-MLOM-CSC-02 Cisco UCS VIC1227 VIC MLOM - Dual Port 10Gb SFP+ N/A Notes The mlom card does not plug into any of the riser 1 or riser 2 card slots; instead, it plugs into a connector inside the chassis. Caveats Other considerations for the Cisco VIC 1227 card: VIC 1227 supports 10G SFP+ optical and copper twinax connections The VIC 1227 is supported with the following software releases: 2.0.8h (CIMC) and above, and 2.2.6f (UCSM). 20

21 CONFIGURING the HX240c M4 Node STEP 8 ORDER GPU CARDS AND GPU POWER CABLES (OPTIONAL) Select GPU Options The available GPU PCIe options are listed in Table 11. Table 11 Available PCIe Option Cards Product ID (PID) PID Description Card Size GPU PCIe Cards UCSC-GPU-VGXK1 NVIDIA GRID K1 Full-height, double wide UCSC-GPU-VGXK2 NVIDIA GRID K2 Full-height, double wide UCSC-GPU-M60 1 M60 GPU GRID 2.0 Notes Requires 300 W cable kit (UCS-300WKIT-240M4) Full-height, double wide CAUTION: When using GPU cards, the operating temperature range is 32 to 95 F (0 to 35 C). NOTE: All GPU cards require two CPUs and a minimum of two power supplies in the server W power supplies are recommended. Use the power calculator at the following link to determine the needed power based on the options chosen (CPUs, drives, memory, and so on): Select GPU Power Cables Whenever you select a K1 or K2 GPU for this server, you must also select one power cable for each GPU selected (however, a maximum of one GPU can be selected). The available GPU power cables are listed in Table 12. Table 12 Available GPU Power Cables Product ID (PID) UCSC-GPUCBL-240M4 PID Description C240 M4 GPU Power Cable 21

22 CONFIGURING the HX240c M4 Node Caveats NVIDIA GPUs can support only less than 1 TB of total memory in the server. Do not install more than fourteen 64-GB DIMMs when using an NVIDIA GPU card in this server. NVIDIA GRID K1 and K2 GPUs can be mixed. No other GPU mixing is allowed. Slot 5 on optional riser card 2 is the required slot for the GPU. A maximum of one GPU can be installed. If a GPU is installed, the chassis must be equipped with either a 1200 W or 1400 W power supply. 22

23 CONFIGURING the HX240c M4 Node STEP 9 ORDER POWER SUPPLY The HX240c M4 node requires at least one power supply. A lightly loaded system may require one or two 650 W power supplies. A fully loaded system might need to be powered with two larger capacity power supplies. Use the power calculator at the following link to determine the needed power based on the options chosen (CPUs, drives, memory, and so on): Table 13 Power Supply 1 Product ID (PID) UCSC-PSU2-1400W UCSC-PSU2V2-1200W 2 UCSC-PSU-930WDC UCSC-PSU2V2-650W PID Description 1400W AC Power Supply ( V) 2U & 4U C Series System 1200W / 800W V2 AC Power Supply for 2U C-Series Systems 930 W -48V DC Common Slot Power Supply for C-series Systems 650W V2 AC Power Supply for C-Series Systems Notes If a GPU is installed, the chassis must be equipped with a 1200 W or 1400 W power supply. 2. The power output is 1200W with a V input and 800W with a V input. NOTE: In a two power supply system, both power supplies must be identical. 23

24 CONFIGURING the HX240c M4 Node STEP 10 SELECT AC POWER CORD(s) Using Table 14, select the appropriate AC power cords. You can select a minimum of no power cords and a maximum of two. If you select the option R2XX-DMYMPWRCORD, no power cord is shipped with the system. Table 14 Available Power Cords Product ID (PID) PID Description Images R2XX-DMYMPWRCORD CAB-N5K6A-NA No power cord (dummy PID to allow for a no power cord option) Power Cord, 200/240V 6A, North America Not applicable Plug: NEMA 6-15P Cordset rating: 10 A, 250 V Length: 8.2 ft Connector: IEC60320/C CAB-AC-L620-C13 AC Power Cord, NEMA L C13, 2M/6.5ft CAB-C13-CBN CABASY,WIRE,JUMPER CORD, 27" L, C13/C14, 10A/250V CAB-C13-C14-2M CABASY,WIRE,JUMPER CORD, PWR, 2 Meter, C13/C14,10A/250V CAB-C13-C14-AC CORD,PWR,JMP,IEC60320/C14,IEC6 0320/C13, 3.0M 24

25 16A 250V OVE CONFIGURING the HX240c M4 Node Table 14 Available Power Cords Product ID (PID) PID Description Images CAB-250V-10A-AR Power Cord, 250V, 10A, Argentina 2500 mm Plug: EL 219 (IRAM 2073) Cordset rating: 10 A, 250/500 V MAX Length: 8.2 ft Connector: EL 701 (IEC60320/C13) CAB-9K10A-AU Power Cord, 250VAC 10A 3112 Plug, Australia Cordset rating: 10 A, 250 V/500 V MAX Length: 2500mm Plug: EL 210 (BS 1363A) 13 AMP fuse Connector: EL 701C (EN 60320/C15) CAB-250V-10A-CN AC Power Cord - 250V, 10A - PRC CAB-9K10A-EU Power Cord, 250VAC 10A CEE 7/7 Plug, EU Plug: M2511 Cordset rating: 10A/16 A, 250 V Length: 8 ft 2 in. (2.5 m) Connector: VSCC SFS-250V-10A-ID Power Cord, SFS, 250V, 10A, India Plug: EL 208 Cordset rating 16A, 250V (2500mm) Connector: EL SFS-250V-10A-IS Power Cord, SFS, 250V, 10A, Israel EL-212 Cordset rating 10A, 250V/500V MAX (2500 mm) Plug: EL 212 (SI-32) Connector: EL 701B (IEC60320/C13) CAB-9K10A-IT Power Cord, 250VAC 10A CEI 23-16/VII Plug, Italy Plug: I/3G (CEI 23-16) Cordset rating: 10 A, 250 V Length: 8 ft 2 in. (2.5 m) Connector C15M (EN60320/C15 )

26 From Plug End CONFIGURING the HX240c M4 Node Table 14 Available Power Cords Product ID (PID) PID Description Images CAB-9K10A-SW Power Cord, 250VAC 10A MP232 Plug, Switzerland Plug: MP232-R Cordset rating: 10 A, 250 V Length: 8 ft. 2 in (2.5 m) Connector: IEC C CAB-9K10A-UK Power Cord, 250VAC 10A BS1363 Plug (13 A fuse), UK Cordset rating: 10 A, 250 V/500 V MAX Length: 2500mm Plug: EL 210 (BS 1363A) 13 AMP fuse Connector: EL 701C (EN 60320/C15) CAB-9K12A-NA Power Cord, 125VAC 13A NEMA 5-15 Plug, North America CAB-250V-10A-BR Power Cord - 250V, 10A - Brazil 2,133.6 ± 25 CAB-JPN-3PIN Power Cord 3PIN, Japan Image not available 26

27 CONFIGURING the HX240c M4 Node STEP 11 ORDER TOOL-LESS RAIL KIT AND OPTIONAL REVERSIBLE CABLE MANAGEMENT ARM Select a Tool-Less Rail Kit Select a tool-less rail kit from Table 15. Table 15 Tool-Less Rail Kit Options Product ID (PID) UCSC-RAILB-M4 PID Description Ball Bearing Rail Kit Select an Optional Reversible Cable Management Arm The reversible cable management arm mounts on either the right or left slide rails at the rear of the system and is used for cable management. Use Table 16 to order a cable management arm. Table 16 Cable Management Arm Product ID (PID) UCSC-CMA-M4 PID Description Reversible CMA for tool-less ball bearing rail kit For more information about the tool-less rail kit and cable management arm, see the Cisco UCS C240 M4 Installation and Service Guide at this URL: NOTE: If you plan to rackmount your HX240c M4 node, you must order a tool-less tool-less rail kit. 27

28 CONFIGURING the HX240c M4 Node STEP 12 ORDER A TRUSTED PLATFORM MODULE (OPTIONAL) Trusted Platform Module (TPM) is a computer chip (microcontroller) that can securely store artifacts used to authenticate the platform (system). These artifacts can include passwords, certificates, or encryption keys. A TPM can also be used to store platform measurements that help ensure that the platform remains trustworthy. Authentication (ensuring that the platform can prove that it is what it claims to be) and attestation (a process helping to prove that a platform is trustworthy and has not been breached) are necessary steps to ensure safer computing in all environments. The TPM ordering information is listed in Table 17. Table 17 Trusted Platform Module Product ID (PID) UCSX-TPM2-001 PID Description Trusted Platform Module 1.2 SPI-based NOTE: The module used in this system conforms to TPM v1.2 and 2.0, as defined by the Trusted Computing Group (TCG). It is also SPI-based. 28

29 CONFIGURING the HX240c M4 Node STEP 13 ORDER CISCO FLEXIBLE FLASH SD CARD MODULE You must order two 64 GB SD cards. The SD cards are mirrored to each other and are used for booting. See Figure 7 on page 39 for the location of the SD cards. There are two locations, SD1 and SD2. Table GB Secure Digital (SD) Card Product ID (PID) UCS-SD-64G-S PID Description 64 GB SD Card Caveats You must select two 64 GB SD cards 29

30 CONFIGURING the HX240c M4 Node STEP 14 SELECT OPERATING SYSTEM AND VALUE-ADDED SOFTWARE Several operating systems and value-added software programs are available. Select as desired from Table 1. Table 19 OSs and Value-Added Software PID Description Product ID (PID) VMware 1 HX-VSP-STD-D HX-VSP-STD-DL HX-VSP-EPL-D HX-VSP-EPL-DL HX-VSP-FND-D HX-VSP-FND-DL HX-VSP-STD-D HX-VSP-STD-DL Software Subscription HXDP-001-2YR HXDP-001-4YR Factory Installed - VMware vsphere6 Std SW and Lic (2 CPU) Factory Installed - VMware vsphere6 Standard SW Download Factory Installed - VMware vsphere6 Ent Plus SW+Lic (2 CPU) Factory Installed - VMware vsphere6 Enterprise Plus SW Dnld Factory Installed - vsphere SW (End user to provide License) Factory Installed - VMware vsphere6 Foundation SW Download Factory Installed - VMware vsphere6 Std SW and Lic (2 CPU) Factory Installed - VMware vsphere6 Standard SW Download Cisco HyperFlex HX Data Platform SW 1 Yr Subscription Cisco HyperFlex HX Data Platform SW 3 Yr Subscription HXDP-S001-1YR= Cisco HyperFlex HX Data Platform SW 1 yr Subscription v2.0 HXDP-S001-2YR= Cisco HyperFlex HX Data Platform SW 2 yr Subscription v2.0 HXDP-S001-3YR= Cisco HyperFlex HX Data Platform SW 3 yr Subscription v2.0 HXDP-S001-4YR= Cisco HyperFlex HX Data Platform SW 4 yr Subscription v2.0 HXDP-S001-5YR= Cisco HyperFlex HX Data Platform SW 5 yr Subscription v2.0 Notes Although VMware 6.0 is installed at the factory, both VMware 5.5 and VMware 6.0 are supported. 30

31 CONFIGURING the HX240c M4 Node STEP 15 SELECT SERVICE and SUPPORT LEVEL A variety of service options are available, as described in this section. Unified Computing Warranty, No Contract If you have noncritical implementations and choose to have no service contract, the following coverage is supplied: Three-year parts coverage. Next business day (NBD) onsite parts replacement eight hours a day, five days a week. 90-day software warranty on media. Ongoing downloads of BIOS, drivers, and firmware updates. UCSM updates for systems with Unified Computing System Manager. These updates include minor enhancements and bug fixes that are designed to maintain the compliance of UCSM with published specifications, release notes, and industry standards. Smart Net Total Care for UCS For support of the entire Unified Computing System, Cisco offers the Cisco Smart Net Total Care for UCS Service. This service provides expert software and hardware support to help sustain performance and high availability of the unified computing environment. Access to Cisco Technical Assistance Center (TAC) is provided around the clock, from anywhere in the world. For systems that include Unified Computing System Manager, the support service includes downloads of UCSM upgrades. The Cisco Smart Net Total Care for UCS Service includes flexible hardware replacement options, including replacement in as little as two hours. There is also access to Cisco's extensive online technical resources to help maintain optimal efficiency and uptime of the unified computing environment. You can choose a desired service listed in Table 20. Table 20 Cisco Smart Net Total Care for UCS Service Product ID (PID) On Site? Description CON-PREM-HX240M4S Yes ONSITE 24X7X2 HX240C M4 SFF - SFF CON-OSPT-HX240M4S Yes ONSITE Troubleshooting 24x7x4 HX240C M4 SFF-SFF CON-C4P-HX240M4S Yes ONSITE 24X7X4 HX240C M4 SFF - SFF CON-OSE-HX240M4S Yes ONSITE 8X5X4 HX240C M4 SFF - SFF CON-OS-HX240M4S Yes ONSITE 8X5XNBD HX240C M4 SFF - SFF CON-S2P-HX240M4S No SMARTNET 24X7X2 HX240C M4 SFF - SFF CON-SNTP-HX240M4S No SMARTNET 24X7X4 HX240C M4 SFF - SFF CON-SNTE-HX240M4S No SMARTNET 8X5X4 HX240C M4 SFF - SFF CON-SNT-HX240M4S No SMARTNET 8X5XNBD HX240C M4 SFF - SFF 31

32 CONFIGURING the HX240c M4 Node Unified Computing Partner Support Service Cisco Partner Support Service (PSS) is a Cisco Collaborative Services service offering that is designed for partners to deliver their own branded support and managed services to enterprise customers. Cisco PSS provides partners with access to Cisco's support infrastructure and assets to help them: Expand their service portfolios to support the most complex network environments Lower delivery costs Deliver services that increase customer loyalty Partner Unified Computing Support Options enable eligible Cisco partners to develop and consistently deliver high-value technical support that capitalizes on Cisco intellectual assets. This helps partners to realize higher margins and expand their practice. PSS is available to all Cisco PSS partners. The Partner Unified Computing Support Option for the Cisco HX240C Node is: Partner Support Service for UCS Partner Support Service for UCS provides hardware and software support, including triage support for third party software, backed by Cisco technical resources and level three support. See Table 21. Table 21 Partner Support Service for UCS Product ID (PID) Service Level GSP On Site? Description CON-PSJ1-HX240M4S PSJ1 No UCS SUPP PSS 8X5XNBD HX240C M4 SFF - SFF CON-PSJ2-HX240M4S PSJ2 No UCS SUPP PSS 8X5X4 HX240C M4 SFF - SFF CON-PSJ3-HX240M4S PSJ3 No UCS SUPP PSS 24X7X4 HX240C M4 SFF - SFF CON-PSJ4-HX240M4S PSJ4 No UCS SUPP PSS 24X7X2 HX240C M4 SFF - SFF Unified Computing Combined Support Service Combined Services makes it easier to purchase and manage required services under one contract. Smart Net Total Care services for UCS help increase the availability of your vital data center infrastructure and realize the most value from your unified computing investment. The more benefits you realize from the Cisco Unified Computing System (Cisco UCS), the more important the technology becomes to your business. These services allow you to: Optimize the uptime, performance, and efficiency of your UCS Protect your vital business applications by rapidly identifying and addressing issues Strengthen in-house expertise through knowledge transfer and mentoring Improve operational efficiency by allowing UCS experts to augment your internal staff resources 32

33 CONFIGURING the HX240c M4 Node Enhance business agility by diagnosing potential issues before they affect your operations You can choose a service listed in Table 22. Table 22 UCS Computing Combined Support Service Product ID (PID) Service Level GSP On Site? Description CON-NCF2-HX240M4S NCF2 No CMB SPT SVC 24X7X2 HX240C M4 SFF - SFF CON-NCF2P-HX240M4S NCF2P Yes CMB SPT SVC 24X7X2OS HX240C M4 SFF - SFF CON-NCF4P-HX240M4S NCF4P Yes CMB SPT SVC 24X7X4OS HX240C M4 SFF - SFF CON-NCF4S-HX240M4S NCF4S Yes CMB SPT SVC 8X5X4OS HX240C M4 SFF - SFF CON-NCFCS-HX240M4S NCFCS Yes CMB SPT SVC 8X5XNBDOS HX240C M4 SFF - SFF CON-NCFE-HX240M4S NCFE No CMB SPT SVC 8X5X4 HX240C M4 SFF - SFF CON-NCFP-HX240M4S NCFP No CMB SPT SVC 24X7X4 HX240C M4 SFF - SFF CON-NCFT-HX240M4S NCFT No CMB SPT SVC 8X5XNBD HX240C M4 SFF - SFF Smart Net Total Care for UCS with Drive Retention With the Smart Net Total Care for UCS with Drive Retention (UCSDR) Service, you can obtain a new disk drive in exchange for a faulty drive without returning the faulty drive. In exchange for a Cisco replacement drive, you provide a signed Certificate of Destruction (CoD) confirming that the drive has been removed from the system listed, is no longer in service, and has been destroyed. Sophisticated data recovery techniques have made classified, proprietary, and confidential information vulnerable, even on malfunctioning disk drives. The UCDR service enables you to retain your drives and ensures that the sensitive data on those drives is not compromised, which reduces the risk of any potential liabilities. This service also enables you to comply with regulatory, local, and federal requirements. If your company has a need to control confidential, classified, sensitive, or proprietary data, you might want to consider one of the Drive Retention Services listed in Table 23 on page 34. NOTE: Cisco does not offer a certified drive destruction service as part of this service. 33

34 CONFIGURING the HX240c M4 Node Table 23 Drive Retention Service Options Service Description Service Program Name Service Level GSP Service Level Product ID (PID) Smart Net Total Care for UCS with Drive Retention UCS DR UCSD8 24x7x2 Onsite CON-UCSD8-HX240M4S OSPTD 24x7x4 Onsite Troubleshooting CON-OPSTD-HX240M4S UCSD7 24x7x4 Onsite CON-UCSD7-HX240M4SF UCSD5 8x5xNBD Onsite CON-UCSD5-HX240M4SF For a complete listing of available services for Cisco Unified Computing System, see this URL: 34

35 OPTIONAL STEP - ORDER RACK(s) OPTIONAL STEP - ORDER RACK(s) The optional R42610 rack is available from Cisco for the C-Series systems, including the HX240c M4 Node. This rack is a standard 19-inch rack and can be ordered with a variety of options, as listed in Table 24. Racks are shipped separately from the HX240c M4 Node. Table 24 Racks and Rack Options Product ID (PID) RACK-UCS 1 RACK-UCS2 1 RACK-BLANK-001 RACK-CBLMGT-001 RACK-CBLMGT-011 RACK-FASTEN-001 RACK-FASTEN-002 RACK-JOIN-001 PID Description Cisco R42610 expansion rack, no side panels Cisco R42610 standard rack, w/side panels Filler panels (qty 12), 1U, plastic, toolless Cable mgt D rings (qty 10), metal Cable mgt straps (qty 10), Velcro Mounting screws (qty 100), M6 Cage nuts (qty 50), M6 Rack joining kit Notes Use these same base PIDs to order spare racks (available only as next-day replacements). For more information about the R42610 rack, see RACKS, page

36 OPTIONAL STEP - ORDER PDU OPTIONAL STEP - ORDER PDU An optional power distribution unit (PDU) is available from Cisco for the C-Series rack systems, including the HX240c M4 Node. This PDU is available in a zero rack unit (RU) style (see Table 25). Table 25 PDU Options Product ID (PID) RP P-U-2 PID Description Zero RU PDU For more information about the PDU, see PDUs, page

37 SUPPLEMENTAL MATERIAL SUPPLEMENTAL MATERIAL Hyperconverged Systems Cisco HyperFlex Systems let you unlock the full potential of hyperconvergence and adapt IT to the needs of your workloads. The systems use an end-to-end software-defined infrastructure approach, combining software-defined computing in the form of Cisco HyperFlex HX-Series nodes; software-defined storage with the powerful Cisco HX Data Platform; and software-defined networking with the Cisco UCS fabric that will integrate smoothly with Cisco Application Centric Infrastructure (Cisco ACI). Together with a single point of connectivity and management, these technologies deliver a preintegrated and adaptable cluster with a unified pool of resources that you can quickly deploy, adapt, scale, and manage to efficiently power your applications and your business. Figure 5 shows a small footprint cluster and Figure 6 shows a compute-intensive hybrid cluster. Figure 5 Small Footprint Cluster Using HX420c M4 Nodes Cisco HyperFlex Systems Connectivity (small footprint cluster) Cisco Nexus 9000 Series Switch (optional) Cisco Nexus 9000 Series Switch (optional) vpc Shared Services peer link vcenter Cisco UCS 6248UP Fabric Interconnect vpc vpc Cisco UCS 6248UP Fabric Interconnect DHCP NTP DNS Active Directory Legend Cisco HX240c M4 Nodes (3 minimum) Converged 10 GbE Interconnects Each HX240c M4 Node contains: - 2 x Intel Xeon CPU E (v3 2.5 GHz processor) GB (24 x 16 GB DDR4) RAM - 1 x Cisco 12G SAS HBA - 1 x 120 GB SATA SSD - 1 x 1.6 TB SATA SSD - 23 x 1.2 TB SAS 12 Gbs10K RPM HDDs - Cisco VIC1227 MLOM (2 x 10G ports) - 2 x 64 GB SD Cards 37

38 SUPPLEMENTAL MATERIAL Figure 6 Compute-Intensive Hybrid Cluster Using HX240c M4 Nodes and B200 M4 Blades Cisco HX Connectivity (compute-intensive hybrid cluster) Cisco Nexus 9000 Series Switch (optional) Cisco Nexus 9000 Series Switch (optional) vpc Shared Services peer link vcenter Cisco UCS 6248UP Fabric Interconnect vpc vpc Cisco UCS 6248UP Fabric Interconnect DHCP NTP DNS Active Directory Legend Cisco UCS HX240c M4 Nodes (3 minimum) Converged 10 GbE Interconnects CiscoUCS 5108 BladeChassis With 3 x B200 M4 Blades Each HX240c M4 contains: - 2 x Intel Xeon CPU E (v3 2.5 GHz processor) GB (24 x 16 GB DDR4) RAM - 1 x Cisco 12G SAS HBA - 1 x 120 GB SATA SSD - 1 x 1.6 TB SATA SSD - 23 x 1.2 TB SAS 12 Gbs10K RPM HDDs - Cisco VIC1227 MLOM (2 x 10G ports) - 2 x 64 GB SD Cards Each B200 M4 blade contains: - 2 x Intel Xeon ES-2680 v3 2.5 GHz processors GB (24 x 16 GB DDR4) RAM - Cisco VIC x 64 GB SD Cards. 38

39 SUPPLEMENTAL MATERIAL Chassis An internal view of the HX240c M4 Node chassis with the top cover removed is shown in Figure 7. The location of the two SD cards is marked with callout #5 and the location of the SATA SSD SDS logs drives is marked with callout #11. Figure 7 HX240c M4 Node Chassis With Top Cover Off FAN 06 SD2 SD1 7 1 FAN 05 FAN 04 FAN 03 FAN 02 FAN 01 CPU 2 CPU 1 Riser 2 Riser Drives (SAS/SATA drives are hot-swappable) 10 PCIe riser 1 (PCIe slots 1, 2, 3*) 2 Fan modules (six, hot-swappable) 11 SATA SSD SDS logs drives (two sockets available only on PCIe riser 1) 3 DIMM sockets on motherboard (either 16 or 24 DIMMs populated) 12 mlom card socket on motherboard under PCIe riser 1 4 CPUs and heatsinks (two) 13 Socket for embedded RAID interposer board (not used) 5 Cisco SD card slots on motherboard (two) 14 Cisco modular drive controller PCIe slot (dedicated slot and bracket) 6 USB 3.0 slot on motherboard (not used) 15 RTC battery on motherboard 7 Power supplies (hot-swappable, accessed through rear panel) 8 Trusted platform module (TPM) socket on motherboard, under PCIe riser 2 9 PCIe riser 2 (PCIe slots 4, 5, 6) 16 Embedded RAID header for RAID key (not used) 17 SuperCap power module (RAID backup) mounting location on air baffle (not shown) (not used) 39

40 SUPPLEMENTAL MATERIAL Block Diagram A simplified block diagram of the HX240c M4 Node is shown in Figure 8. Figure 8 HX240c M4 Node Block Diagram (simplified) UCSC-C240-M4S, 2U, 8-2.5" drives X4 SAS Connector SAS x4 SAS x4 UCSC-C240-M4S2, 2U, " drives 24-port SAS Expander X4 SAS Connector SAS x4 X4 SAS Connector... X4 SAS Connector. SAS x4 UCSC-C240-M4SX, 2U, " drives 36-port SAS Expander SAS x4 X4 SAS Connector... X4 SAS Connector. SAS x4 UCSC-C240-M4L, 2U, " drives 20-port SAS Expander SATA SAS x4 X4 SAS Connector... X4 SAS Connector X4 SAS Connector X4 SAS Connector Cables to modular RAID card or Wellsburg connectors or PCIe Interposer* SATA Cables to modular RAID card connectors or PCIe Interposer* A1A2 A3 B1B2 B3 Chan A Chan B C1C2 C3 Chan C D1D2 D3 Chan D Cables to Modular RAID card connectors or PCIe Interposer* E1 E2 E3 F1 F2 F3 Chan E Chan F G1G2 G3 H1H2 H3 Chan G Chan H. SAS x4 SAS/SATA Intel Wellsburg PCH X4 SAS Connector X4 SAS Connector Cables to modular RAID card connectors SAS/SATA USB Thumbdrive X2 AHCI PCIe DMI2 (x4) Gen2 SD1 SD2 DMI2 Intel Xeon Haswell XP (CPU 1) QPI (9.6 GT) Intel Xeon Haswell XP (CPU 2) Modular RAID Card PCIe x8 Gen 3 BMC PCIe PCIe x16 Gen3 PCIe x8 Gen3 PCIe x8 Gen3 PCIe x8 Gen3 PCIe x8 Gen3 X2 AHCI PCIe x16 Gen3 PCIe x8 Gen3 PCIe x8 Gen3 PCIe x16 Gen3 PCIe x8 Gen3 2-port i350 NIC GbE switch mlom Module (a variety of network cards can be installed here) PCIe Riser 1 (option 1) Slot 2 Slot 1 PCIe Riser 1 (option 2) Slot 3 Slot 2 Slot 1 PCIe Riser 1 (option 3) SATA 1 SATA 2 Slot 2 Slot 1 PCIe Riser 2 Slot 6 Slot 5 Slot 4 Rear Panel USB USB VGA Serial 1 GB-T 1 GB-T 1 GB-T (Mgmt) Network connectors (types vary with mlom module) Cisco tem Block Diagram Four Options for Drive Backplane Gen2 (6 Gb/s) Gen3 (12 Gb/s) USB 3.0 PCIe SD controller SD 3.0 QPI (9.6 GT) Front Panel KVM Connector X2 USB VGA 1 Serial PCIe x8 Gen 3 *For PCIe drives in slots 1 and 2 only PCIe x4 Gen3 PCIe x4 Gen3 PCIe Interposer (optional) X2 mini SAS HD 40

41 SUPPLEMENTAL MATERIAL CPUs and DIMMs Physical Layout Each CPU has four DIMM channels: CPU1 has channels A, B, C, and D CPU2 has channels E, F, G, and H Each DIMM channel has three slots: slot 1, slot 2, and slot 3. The blue-colored DIMM slots are for slot 1, the black-colored slots for slot 2, and the white slots for slot 3. As an example, DIMM slots A1, B1, C1, and D1 belong to slot 1, while A2, B2, C2, and D2 belong to slot 2. Figure 9 shows how slots and channels are physically laid out on the motherboard. The DIMM slots on the right half of the motherboard (channels A, B, C, and D) are associated with CPU 1, while the DIMM slots on the left half of the motherboard (channels E, F, G, and H) are associated with CPU 2. The slot 1 (blue) DIMM slots are always located farther away from a CPU than the corresponding slot 2 (black) and slot 3 (white) slots. Slot 1 slots (blue) are populated before slot 2 slots (black) and slot 3 (white) slots. Figure 9 Physical Layout of CPU DIMM Channels and Slots 41

42 SUPPLEMENTAL MATERIAL Memory Population Rules When considering the memory configuration of your HX240c Node, consider the following items: Each channel has three DIMM slots (for example, channel A = slots A1, A2, and A3). A channel can operate with one, two, or three DIMMs installed. If a channel has only one DIMM, populate slot 1 first (the blue slot). When both CPUs are installed, populate the DIMM slots of each CPU identically. Fill blue slots in the channels first: A1, E1, B1, F1, C1, G1, D1, H1 Fill black slots in the channels second: A2, E2, B2, F2, C2, G2, D2, H2 Fill black slots in the channels third: A3, E3, B3, F3, C3, G3, D3, H3 Any DIMM installed in a DIMM socket for which the CPU is absent is not recognized. Observe the DIMM mixing rules shown in Table 26 Table 26 DIMM Rules for HX240c Nodes DIMM Parameter DIMMs in the Same Channel DIMM in the Same Slot 1 DIMM Capacity RDIMM = 16, 32, or 64 GB DIMM Speed 2133-MHz 2 DIMMs in the same channel (for example, A1, A2, and A3) can have different capacities. DIMMs will run at the lowest speed of the DIMMs/CPUs installed For best performance, DIMMs in the same slot (for example, A1, B1, C1, D1) should have the same capacity. DIMMs will run at the lowest speed of the DIMMs/CPUs installed DIMM Type RDIMMs Do not mix DIMM types in a channel Do not mix DIMM types in a slot DIMMs per Channel (DPC) 1 DPC, 2 DPC, or 3 DPC See Table 6 on page 16 for valid RDIMM 1 DPC, 2 DPC, and 3 DPC memory configurations Notes Although different DIMM capacities can exist in the same slot, this will result in less than optimal performance. For optimal performance, all DIMMs in the same slot should be identical. 2. Only 2133-MHz DIMMs are currently available for the HX240c M4 node. 42

43 SUPPLEMENTAL MATERIAL DIMM Population Order Populate the DIMMs for a CPU according to Table 27. Table 27 DIMM Population Order per CPU DIMMs per CPU Populate CPU 1 Slots Populate CPU 2 Slots 8 A1, B1, C1, D1, A2, B2, C2, D2 12 A1, B1, C1, D1, A2, B2, C2, D2 A3, B3, C3, D3 E1, F1, G1, H1, E2, F2, G2, H2 E1, F1, G1, H1, E2, F2, G2, H2 E3, F3, G3, H3 43

44 SUPPLEMENTAL MATERIAL Serial Port Details The pinout details of the rear RJ-45 serial port connector are shown in Figure 10. Figure 10 Serial Port (Female RJ-45 Connector) Pinout Serial Port (RJ-45 Female Connector) Pin Signal RTS (Request to Send) DTR (Data Terminal Ready) TxD (Transmit Data) GND (Signal Ground) GND (Signal Ground) RxD (Receive Data) DSR (Data Set Ready) CTS (Clear to Send) 44

45 SUPPLEMENTAL MATERIAL Upgrade and Servicing-Related Parts This section lists the upgrade and servicing-related parts you may need during the life of your HX240c Node. Some of these parts are configured with every system, and some may be ordered when needed or may be ordered and kept on hand as spares for future use. See Table 28. Table 28 Upgrade and Servicing-related Parts for HX240c M4 Node Spare Product ID (PID) Description UCSC-PCIF-01F= PCIe Full Height blanking panel 1 UCSC-PCIF-C240M4= PCIe Riser Blanking Panel 1 UCSC-PCI-2-C240M4= PCIe Riser 2 Assembly 1 UCSC-PCI-1A-240M4= PCIe Riser 1 Assembly UCSC-PCI-1B-240M4= PCIe Riser 1 Assembly (3 x8 slots) 1 UCSC-PCI-1C-240M4= UCSC-MLOM-BLK= M4 PCIe Riser 1 Assembly MLOM Blanking Panel UCSC-HS-C240M3= Heat Sink 1 UCS-CPU-LPCVR= CPU load plate dust cover (for unpopulated CPU sockets) N20-MBLIBATT= Replacement Lithium Battery for motherboard (CR2032) 1 UCSC-FAN-C240M4= UCSC-BAFF-C240M4= Fan Module (one) Air Baffle Replacement Kit UCSC-PSU-BLKP240= Power Supply Blanking Panel 1 UCSC-RAILB-M4= UCSC-CMAB-M4= UCS-SD-64G-S= N20-BKVM= Tool-Less Ball Bearing Rail Kit Reversible CMA for ball bearing rail kit 64 GB SD Card KVM local IO cable for console port UCS-CPU-GREASE3= CPU thermal grease syringe - needed for heatsink seal 2 UCSX-HSCK= UCS Processor Heat Sink Cleaning Kit (when replacing a CPU) 3 Notes This part is included/configured with your HX240c M4 Node (in some cases, as determined by the configuration of your node). 2. This part should be ordered with the purchase of each optional or spare Intel Xeon E v3 or v4 CPU processor kit 45

46 SUPPLEMENTAL MATERIAL Adding an Additional CPU (with CPU heat sink) or Replacing CPUs All Cisco UCS two CPU socket-capable systems can be upgraded from having one to having two CPUs configured or can also support replacement of the CPUs. You will need to order and install a heat sink when adding any additional CPU to a system. Instructions for installing the new CPU or replacing CPUs and heat sink can be found at the following link: NOTE: Unlike previous generation systems, the HX240c M4 Node has tool-less CPU sockets, so no separate tools (such as pick n place tools) are required to add or replace CPUs. See the section titled Replacing CPUs and Heatsinks. Motherboard Lithium Battery You can order a replacement motherboard battery. Installation instructions are found at this link: See the section titled Replacing the Motherboard RTC Battery. Thermal Grease (with syringe applicator) for CPU to Heatsink Seal Thermal grease must be applied to the top of the CPU where it comes in contact with the heat sink (a grease syringe also ships with each CPU spare option kit). Instructions for applying thermal grease are found at: See the section titled Replacing CPUs and Heatsinks. CAUTION: Use only the thermal grease specified for this system (UCS-CPU-GREASE3=). This thermal grease comes in a white-tipped syringe and is to be used only in the HX220c M4 and HX240c M4 Nodes. Other systems use thermal grease in a blue-tipped syringe (UCS-CPU-GREASE=). Thermal grease for other systems may have different thermal conductivity properties and may cause overheating if used in the HX220c M4 or HX240c M4 Nodes. DO NOT use thermal grease available for purchase at any commercial electronics store. If these instructions are not followed, the CPU may overheat and be destroyed. 46

47 SUPPLEMENTAL MATERIAL NOTE: When you purchase a spare CPU, the thermal grease with syringe applicator is included. Air Baffle Replacement Kit Air baffles are designed to direct airflow through the system to maintain the temperature at a safe operating level. These baffles must always remain installed during operation. The Air Baffle Replacement Kit includes the air baffles needed for one HX240c M4 node. CPU Heat Sink Cleaning Kit The cleaning kit is used to remove the existing thermal compound from the bottom of the heat sink during a CPU replacement process. Instructions for cleaning are found at the following link: See the section titled Replacing CPUs and Heatsinks. NOTE: When you purchase a spare CPU, the CPU cleaning kit is included. 47

48 SUPPLEMENTAL MATERIAL Riser Card Configuration and Options The riser card 2 slot assignments are fixed and are shown in Table 29. Table 29 Riser Card 2 Slots Slot # Height Length Electrical Mechanical NCSI Physical Riser Card 2 Slot 6 Slot 5 Slot 4 6 Full Full x8 x16 No 5 Full Full 1 x16 x24 Yes 2 4 Full 3/4 x8 x24 Yes 2 Notes GPU capable slot 2. NCSI supported in only one slot at a time (default slot 5). If a GPU card is present in slot 5, NCSI support automatically moves to slot 4. 48

49 SUPPLEMENTAL MATERIAL RACKS The Cisco R42610 rack (see Figure 11 on page 50) is certified for Cisco UCS installation at customer sites and is suitable for the following equipment: Cisco UCS B-Series servers and fabric interconnects Cisco UCS C-Series and select Nexus switches The rack is compatible with hardware designed for EIA-standard 19-inch racks. Rack specifications are listed in Table 30. Table 30 Cisco R42610 Rack Specifications Parameter Standard Rack Expansion Rack Dimensions (H x W x D) Dimensions (H x W x D) with packaging x 24 x in. (2000 x 610 x 1102 mm) 89 x 33 x 47 in. (2261 x 838 x 1194 mm) x x in. (2000 x 599 x 1102 mm) 89 x 33 x 47 in. (2261 x 838 x 1194 mm) Distance from front mounting rail to rear mounting rail 29.2 in (741 mm) 29.2 in (741 mm) Weight lb (136 kg) lb (105 kg) Weight with packaging 354 lb (161 kg) 284 lb (129 kg) Side panels included Yes No Equipment mounting capacity Static load capacity 42RU 2100 lb (954 kg) 42RU 2100 lb (954 kg) Dynamic load capacity Not applicable Not applicable NOTE: The AC input connector is an IEC 320 C A/250 VAC power inlet. 49

50 SUPPLEMENTAL MATERIAL Figure 11 Cisco R42610 Rack Front view - door closed Front view - door open Front view - door removed 50