DO YOU WANT TO AIM EVEN HIGHER? FOR THIS THERE IS DIGIMAR.

Transcription

1 - DO YOU WANT TO AIM EVEN HIGHER? FOR THIS THERE IS DIGIMAR. Mahr offers you the complete product program in order for you to obtain the most reliable solution for all your measuring tasks. Whether it s simply scribing a work piece or complex measurements in two dimensions - Digimar Height Measuring Instruments guarantee a maximum of both flexibility and quality. Our motorized Height Measuring Instruments Digimar CX1 and CX2 exceed all customer requirements; they are simple to operate, all the basic functions can be executed with a single key as well as offering a maximum of ease and accuracy.

2 + Overview Digimar Height Measuring Instruments 2-2 Motorized Height Measuring Instruments Digimar CX1 2-4 High-End Height Measuring Instrument with 2D and Statistics function Digimar CX2 2-8 Height Measuring Instrument for the workshop and test labor Accessories for CX1 and CX Manual Height Measuring Instruments Digimar M 814 N 2-13 With Cast Iron Base Digimar M 814 G 2-14 With Granite Table Plate Accessories for Digimar M Height Measuring and Scribing Instrument Digimar 27 ES 2-16 General Accessories for Height Measuring Instruments 2-17

3 - 2-2 Overview Digimar CX1 Digimar CX2 Catalog page Measuring range mm/inch / / / / 0-40 Application range up to mm/inch 935 / / / / Measuring error* (U95) in µm 2+L/600 (L in mm) 5+L/300 (L in mm) 5+L/300 (L in mm) 5+L/300 (L in mm) 1-D 1D Motorized measuring carriage Scribing/marking work pieces Bore diameter Max-Min 0 Tolerance monitoring Perpendicularity measurement Straightness measurement Angle calculation 2-D Statistics TOL 2D P rog Measuring program Air cushion Interface RS232 RS232 RS232 RS232 RS232C Printer interface Centronics Order no * with Standard Accessories

4 + 2-3 Overview Digimar M 814 N Digimar M 814 G Digimar 27 ES / / / / / / / / / / / / Opto RS232 Opto RS232 Opto RS232 Opto RS232 Opto RS232 Opto RS

5 - 2-4 Digimar CX1 P rog 2D Digimar CX mm / 24. High End measuring station. Do you have high expectations regarding accuracy and value extensive evaluation possibilities? The Digimar CX1 is easy to use, with numerous functions and setting possibilities, which meets customer requirements. RS232C Features Measuring System Excellent accuracy due to the opto-electric incremental measuring system Dynamic probing system enables high repeatability Precise measuring head travels on a fully encased steel guides which are protected from dirt Motorized measuring carriage simplifies the measuring task and minimizes the influence caused by the operator It is possible to have 2 additional zero points on a work piece Storage of 5 different probe constants are possible Probe constant retained even after switching off Battery operated air pump for easy, smooth movement Operating and Display Unit Large and easy to understand operating buttons Easy to read LCD with pictographs and background illumination Plain text dialog boxes, logical menus and easy to follow instructions Operator prompts available in different languages RS232 data output for transmitting data for further data processing Centronics-Interface enables connection to DOS compatible printers Can be connected to up to 4 measuring instruments Integrated rechargeable battery with long operation time for mains independent measurements Automatic Stand-by mode Selectable Auto-off function, without the loss of meas. values Technical Data Measuring range mm/inch 600 / 24 Application range mm/inch 935 / Resolution mm 0.01 / / / / inch / / / / Measuring error U95* µm (2+L/600), L in mm Repeatability* µm 0,5 (plane) 1 (bore) Perpendicularity error (electrically adjusted) µm frontal 8 Operating time between charges h up to 15 Measuring force N 1,0 ± 0,2 Permissible relative air humidity % 65 (non condensed) Working temperature C / F 20 ± 1 / 68 ± 33.8 Operating temperature C / F / Point air cushion, height µm approx. 3 Measuring system incremental scale with opto-electric reading Total height mm/inch 985 / Base area (L x W) mm/inch 240 x 250 / 9.45 x 9.84 Weight kg/lbs 29 / Order no * Base plate GK 0 according to DIN 876 with Probe K10/50

6 + 2-5 Digimar CX1 Measuring Functions 1D-Standard Measurement Functions in semi-automatic mode Measuring made easy with the 16 easily recognizable pictograph operating buttons 1 Contacting a surface from above 9 Contacting a surface from below 4 3 Checking a groove horizontally (center and width) Assessing a bore (center and diameter) 2 Contacting a bore from above Contacting a shaft from above 1 0 Contacting a bore from below Contacting a shaft from below Determining the center of a bore (with a taper probe) 4 Z4 Z Z2-Z1 Z1 Z2 Calculation Functions 5 Calculate the distance between 2 measured values 0 Calculate the symmetry (center) between 2 measured values Measuring Perpendicularity and Straightness Automatic and semi-automatic perpendicularity and straightness measurement Z1 Z2 Z3 3 ø2 ø3 5 Z2-Z3 z 1 α 0 α

7 - 2-6 Digimar CX1 Dynamic Measurements Parallelity Deviation Max-Min Roundness Deviation Max-Min 2D-Measuring functions 8 2D The most important 2D measuring functions can be executed with the touch of a single key, e.g.: perpendicularity measurements, the calculation of an angle or pitch circle. Determine center point and diameter of an index circle. Z X1 Determine the distance and angle between 2 elements D1 Determine the angle between 3 elements d Z1 X Determine the angle of a taper s mean line with respect to the abscissa. Determine the tilting angle. Z Z Z' X' Z2 Z2 Z1 X1 X3 X X2 X

8 + 2-7 Digimar CX1 Measuring program and evaluation of repetitive measurements Measuring program With the Teach-in mode you can quickly devise a measuring program. You only need to measure the work piece once, save this and the measuring program is ready to go. The motorized carriage will travel automatically to the measuring position. The measuring function will start automatically, this reduces the testing time for a mini series consisting of only a few test pieces. 1D and 2D measuring program Creation of a measuring program via the Teach-In function Simple programming and storage of up to 40 measuring programs Tolerance monitoring during a measuring program Creation of production and measuring programs Testing of attributive features Connecting additional hand measuring instruments Statistics Extensive yet enables selective statistical evaluation in the form of histograms, control charts and Pareto charts on either the CX1 or optionally on a PC. Statistical evaluation of individual features Histograms Process control charts Pareto charts Creation of production and measuring programs Evaluation of the basis stored measuring results For the creation and evaluation of inspection plans with the optional software Visustat for PC Print out directly on a DOS-compatible printer Visustat-Software The Visustat program from Mahr can be used for transferring the measured values of either one or several Digimar DX1 instruments to a master computer (PC) where they are stored and are available for statistical evaluations. Furthermore, measuring programs can either be sent from or to the master computer. If necessary the measuring programs can even be edited with Visustat. All printers and plotters compatible to Windows can be used for outputting measuring records. Order no. Visustat-Software Languages (D, E, F, ES, I, P) Data Cable CX1 to PC

9 - 2-8 Digimar CX2 1D P rog RS232C Digimar CX / 600 / 1000 mm (14 / 24 / 40 ) The perfect partner, for use in workshop and inspection areas! Obtain your measurement results without complicated procedures; simple, fast and accurate! The Digital Height Measuring Instrument Digimar CX2 is your perfect partner for use in workshop and inspection areas. Features Measuring System Extremely accurate due to the capacitive incremental measuring system Dynamic probing system enables high repeatability Precise measuring head Motorized measuring carriage simplifies the measuring task and minimizes the influence caused by the operator Switch between Absolute and Relative modes Probe constant remains even after switching off Battery operated air pump for both easy and smooth movement (CX2, 1000 mm/ 40 ) Operating and Display Unit Large, easy to read operating buttons Easy to read Liquid Crystal Display RS232 data output for transmitting data for further data processing Interface for a Digital Indicator for conducting perpendicularity measurements Integrated rechargeable battery with a long operating time for mains independent measurements Auto-off Function Technical Data Measuring range mm/inch 350 / / / 40 Application range mm/inch 685 / / / Resolution mm 0.01 / inch / Measuring error* (U95) µm (5+L/300), L in mm Repeatability* µm 2 (plane) 3 (bore) Perpendicularity error (electrically adjusted) µm Operating time between charges h up to 100 up to 100 up to 15 Measuring force N 1,0 ±0,3 Permissible relative air humidity % 65 (non condensed) Working temperature C / F 20 ± 1 / 68 ± 33.8 Operating temperature C / F / Point air cushion, height µm Yes (approx. 3) Measuring system Incremental capacitive Total height mm/inch 741 / / / Base area (L x W) mm/inch 240 x 250 / 9.45 x 9.84 Weight kg/lbs 14 / / / Order no * Base plate GK 0 according to DIN 876 with Probe K10/50

10 + 2-9 Digimar CX2 Measuring Functions 1D-Standard Measurement Functions in semi-automatic mode The quick reference buttons enables accurate results to be obtained rapidly. 1 Contacting a surface from above 9 Contacting a surface from below 3 2 Checking a groove horizontally (center and width) Assessing a bore (center and diameter) Fct Contacting a bore from above Fct Contacting a shaft from above Fct Contacting a bore from below Fct Contacting a shaft from below 1 Fct 5 Determining the center of a bore (with a taper probe) / continuous display 3 Z4 1 4 Z2-Z1 Z3 5 Z1 Z2 Calculation Functions 4 Calculate the distance between 2 measured values 2 Fct ø2 4 7 Calculate the symmetry (center) between 2 measured values Z1 Z2 Z3 ø3 Z2-Z3 6

11 Digimar CX2 Perpendicularity Measurements Fct Automatic and Semi-automatic α 0 Dynamic Measurements Parallel Deviation Roundness Deviation Max-Min Max-Min Measuring Program With the Teach-in function measuring programs can be simply generated, for example a work piece can be measured, both the results and operating steps can be saved immediately. The motorized measuring head travels to the measuring position, the measuring function will start automatically, therefore even small component batches can be checked quicker and easier. Generated with a Teach-In mode function Simply program and saved up to 20 features Monitoring of tolerances via the measuring program The measuring program remains saved even when the CX2 is switched off Tolerance monitoring with the measuring program

12 Accessories for Digimar CX1 and CX2 Spherical Probes 817 Cl-m K 4/72 17 Catalog no. dia. D A Order no. mm (inch) mm (inch) ø4 A ø4 ø Cl-m 4 (.157 ) 72 (2.83 ) K 4/72 4 (.157 ) 71 (2.78 ) K 4/30 4 (.157 ) 30 (1.18 ) K 6/40 6 (.236 ) 40 (1.57 ) K 10/50 10 (.394 ) 50 (1.97 ) * K 10/60 10 (.394 ) 60 (2.36 ) K 10/ (.394 ) 100 (3.94 ) * Standard accessories K 10/50 ø10 A K 4/30... K 10/100 ød A (55) A Special Probes S 15/47,5 3 TMT Catalog no. Description Order no. ø15 ø12 S 15/47,5 Disc probe Z 10/60 Cylindrical probe MKe 20 Taper probe TMT 86 Spherical probe for recess meas CI-sa Probe with meas. pin CI-am Holder (threaded) for Dial Indicators and Test Indicators te Styli carbide tipped dia. 2 mm* tr Styli ruby dia. 2.5 mm* Z 10/60 ø10 MKe 20 ø20 R7, ,5 ø CI-am 801t ød 16,1 M1,6 817 CI-sa * for 817 CI-am Carriers for Probes and Transducers Carrier 1 ø12 Carrier 2 ø12 Catalog no. Description Order no. Carrier 1 for Probes * Carrier 2 for Probe with joint Carrier 3 for Digital Indicators or Incremental Measuring Probe Carrier 4 for Inductive Measuring Probe 1318 (Only in conjunction with CX1) Carrier 3 79 ø12 72 Carrier 4 ø * Standard accessories Setting Blocks EB EB I Catalog no. Description Order no. EB Setting block * EB I Setting block for taper probe with calibration certificate ø6 H7 * Standard accessories

13 l l Accessories Sets for Digimar CX1 and CX2 Probe Sets Accessories Set CXt1 consists of: Carrying case for accessories Carrier 2 with joint for probe S 15/47,5 Disc probe K 4/30 Spherical probe K 4/72 Spherical probe K 6/40 Spherical probe K 10/60 Spherical probe K 10/100 Spherical probe MKe 20 Spherical probe TMT 86 Spherical probe for measuring recesses or equivalent Z 10/60 Cylindrical probe Universal Probe Set CXt2 consists of: Carrying box Probe carrier Probe carrier 51 37,5 Dimension Shaft length Measuring crook d = 0.5 mm l = 78 mm Probe with pin/tip: dia. d = 1.2 mm l = 75 mm ls = 15.5 mm Taper probe dia. d = mm Spherical probe TC-dia. dk = 3 mm l = 24 mm Spherical probe TC-dia. dk = 2 mm l = 24 mm Spherical probe TC-dia. dk = 1 mm l = 24 mm Extension M3 M3 d = 4 mm l = 20 mm Extension M3 M2.5 d = 4 mm l = 20 mm Measuring crook d Pin probe ls d Taper probe M3 25 Spherical probe dk M3 l Extension piece d M3 l Accessories Sets for checking perpendicularity and straightness Accessories Set CX1p1 consists of: Incremental Measuring Probe 12 mm Carrier 3 for Incremental Measuring Probe Connection cable for Incremental Measuring Probe 1512 to CX Accessories Set CX1p2 consists of: Digital Indicator 12.5 mm Carrier 3 for Digital Indicators Connection cable for 1082 to CX Accessories Set CX2p2 consists of: Digital Indicator 12.5 mm Carrier3 for Digital Indicators Connection cable for 1082 to CX Checking perpendicularity with a 1082 Digital Indicator

14 Digimar M 814 N - standard version 1D Application Ideal for measuring: Heights Center distances between bores and surfaces, widths of ledges, plus marking and scribing of work pieces Features With extra rugged, cast iron base with three-point support. To be used on base plates, machine beds and work piece surfaces. It is also possible to convert into an 814 G version, this can be done simply and quickly at any time. High accuracy Incremental inductive measuring system Measuring head with an ball bush guide Resistance free measuring system Large, easy to read digital display Measuring system and display unit are incorporated in the measuring head Easy to operate due to the hand crank on the side of the measuring head, thus making height adjustment simple Constant measuring force; acting upwards or downwards as required For scribing tasks the measuring head can be locked in position as desired With fine adjustment Data transmission via Opto RS232C interface Digital Preset Zero setting in any position MAX, MIN and MAX-MIN Functions Only 1 tolerance limit can be entered at any one time mm/inch switchable Broad range of accessories Technical Data Measuring range mm/inch 320 / / 24.4 Resolution mm 0.01 / inch / Measuring error µm/µinch 20 / / Repeatability µm/µinch 5 / Perpendicularity error µm frontal 20 (300 mm) frontal 30 (600 mm) Operating time of the Battery h 2000 Measuring force N approx. 3 Working temperature C/ F 20 ± 1 / 68 ± 33.8 Operating temperature C/ F / Measuring system inductive Total height mm/inch 513 / / Cast iron base (L x B) mm/inch 205 x 175 / 8.07 x 6.89 Weight kg/lbs 6.2 / / Order no

15 Digimar M 814 G - Measuring Table Version 1D Application Ideal for measuring: Heights Center distances between bores and surfaces, widths of ledges, plus marking and scribing of work pieces Features Table plate is made of fine grained black granite (greenstone) which is extremely hard and stable. It is also possible to convert into an 814 N version, this can be done simply and quickly at any time. High accuracy Incremental inductive measuring system Measuring head with an ball bush guide Resistance free measuring system Large, easy to read digital display Measuring system and display unit are incorporated in the measuring head Easy to operate due to the hand crank on the side of the measuring head, thus making height adjustment simple Constant measuring force; acting upwards or downwards as required For scribing tasks the measuring head can be locked in position as desired With fine adjustment Data transmission via Opto RS232C interface Digital Preset Zero setting in any position MAX, MIN and MAX-MIN Functions Only 1 tolerance limit can be entered at any one time mm/inch switchable Broad range of accessories Technical Data Measuring range mm/inch 320 / / 24.4 Resolution mm 0.01 / inch / Measuring error µm/µinch 20 / / Repeatability µm/µinch 5 / Perpendicularity error µm frontal 20 (300 mm) frontal 30 (600 mm) Operating time of the battery h 2000 Measuring force N approx. 3 Working temperature C/ F 20 ± 1 / 68 ± 33.8 Operating temperature C/ F / Measuring system inductive Total height mm/inch 558 / / Granite plate (L x W) mm/inch 200 x 300 / 7.87 x Grade 1 DIN 876 Weight kg/lbs 14 / ,3 / Order no

16 Accessories for Digimar M 814 N/G Order no. 814 t Probe arm * with joint for mounting probes, dial indicators, dial comparators and test indicators. Shaft length 150 mm (5.91 ) Mounting bore 8 mm (.315 ) 814 m Ball probe 2 mm Ball (.0787 ) mounted in a probe arm 814 t 3 mm Ball (.118 ) mm Ball (.157 ) mm Ball (.197 ) mm Ball (.236 ) mm Ball (.276 ) mm Ball (.315 ) * 814 s Disc probe for measuring heights, distances, surfaces and edges. Especially recommended for narrow shoulders, e.g. on centering edges. 814 h Probe holder M for mounting styli of dial indicators and dial comparators for special applications. 814 a Scriber for scribing and marking of work pieces. Carbide tipped. To be mounted on the Probe arm 814 t. 814 kh Holder ks1 Measuring taper 0 15 ( ) ks2 Measuring taper ( ) ks3 Measuring taper ( ) ks4 Measuring taper ( ) u Two direction probe 4 mm Ball (.157 ) for measuring outside and inside diameters, width of ledges, recesses, and slots. Actual ball diameter does not influence the results. 814 ua Interchangeable probe arm 2 mm Ball (.0787 ) for use in the Two dierction probe 814 u 814 ua 817 Cl-m Stylus 4 mm Ball (.157 ) Cl-am Holder with connection thread M 2.5, M 1.6, M Cl-sa Stylus with exchangeable measuring pin Cl-p Stylus with parallel measuring faces Battery 3 V, Type CR * Dust cover mm ( ) * Dust cover mm ( ) * 814 Nf Cast iron base ** 814 Gf Table plate ** 814 X Column with measuring head 320 mm (12.60 ) X Column with measuring head 620 mm (24.41 ) ESv Data connection cable Opto RS232C 2 m (78.74 ) * Scope of supply ** for upgrade

17 REF mm/inch ON/OFF RESET Digimar 27 ES 1D Application Scribing and marking of work pieces Measuring heights and distances Features Functions: ON/OFF RESET (Zero setting) mm/inch HOLD (Storage of measuring values) DATA (Data transmission) PRESET (entering a numerical value) Capacitive measuring system, life of battery approx. 2 years Max. measuring speed 1.5 m/s (60 /s) Data output: Opto RS232C via data connection cable High contrast 6 mm Liquid Crystal Display Sturdy heavy-duty base, easy to handle Hardened and lapped contact surface which produce both a smooth and thus even movement Slide and beam made of hardened stainless steel Fine adjustment Locking screw Interchangable scriber point, carbide tipped Standard accessories: Scriber point and battery c 27 ES d Dimensions mm a b c d x x x x a b Technical Data Measuring Resolution Error limit Weight Order no. Order no. Remarks range wooden case mm (inch) mm/inch mm/inch kg/lbs 300 (12 ) 0.01/ / / incl. scriber point 27 ESh 600 (24 ) 0.01/ / / incl. scriber point 27 ESh Accessories Order no. Scriber Point, carbide tipped 27 ESh Holder for test indicators 27 Sp Battery 3V, Type CR Data Connection Cable RS232C (2 m), SUB-D-jack 9-pin 16 ESv Sp 71 11,5x ESh ,5x7

18 General Accessories for Digimar Height Measuring Instruments MSP 2 Statistics Printer Two-line display for simple dialog operation Real time clock with date Measured values can be stored and/or transferred to a PC Optional operation with either mains power supply, batteries or with NIMHrechargeable batteries, Type AA Applicable as an Interface to a PC is possible Language can be simply switched between German, English and French Scope of supply: Mains plug V, paper rolls For further information as well as technical data please refer to page 11-4 Order no. MSP 2 Statistics printer, Euro Type 220V~ MSP 2 Statistics printer, US Type 110V~ Data Cable connects CX 1/ CX 2 to MSP Data Cable connects 814 / 27 ES to MSP OptoFace-Software for data transmission Measuring values can be directly be transferred into an application e.g. MS- EXCEL without the need for key activation Direct data transmission via the serial interface of the PC (COM1 - COM4 are supported) IBM AT compatible PC / MS Windows ; Windows 9x, ME, 2000, XP. Vacant COMinterface is suitable for interruptions of the connection to the measuring instrument Scope of supply: 3.5 floppy disc, operating instructions on a floppy disc Order no. Full version (Geman/English) Data Cable connects CX 1 / CX 2 to PC Data Cable connects 814 / 27 ES to PC