Alternative B Type Mid-Span Power Sourcing Equipment. User s Guide

Transcription

1 Alternative B Type Mid-Span Power Sourcing Equipment User s Guide

2 REGULATORY STATEMENTS FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Changes or modifications not expressly approved by party responsible for compliance could void the user authority to operate the equipment.

3 Table of Contents Introduction...1 SAMPLE APPLICATION...2 PARTS NAMES AND FUNCTIONS...3 Front Panel...3 Rear Panel...4 Hardware Installation...5 DESKTOP INSTALLATION...5 RACK-MOUNTING INSTALLATION...5 CONNECTING OTHER POWER DEVICES...5 How to Manage the Midspan PSE...6 RUN THE GUI UTILITY...6 BASIC GUI UTILITY OPERATION...10 A. System Setup & Control...11 B. System Info:...13 C. Port Specific Control...14 specifications...16 INTERFACE...16 LED INDICATORS...16 INPUT POWER SUPPLY...16 OUTPUT POWER SUPPLY...16 ENVIRONMENTAL...17 REGULATORY...17 PHYSICAL...17

4 INTRODUCTION This Midspan Power Sourcing Equipment (Midspan PSE) is an Alternative B Type 12-port Midspan Power Sourcing Equipment which uses the IEEE 802.3af draft standard to supply Power over Ethernet (PoE) capabilities. This Midspan PSE detects IEEE 802.3af-compliant Alternative B type network devices connected on the front ports, such as IP phones, wireless access points, and video devices among other devices. The Midspan PSE automatically supplies the DC voltage required by each connected appliance at a unique current required for that particular device. Using the Midspan PSE, you can use any 802.3af-draft-compliant network device without connecting the device separately to a power source. The Midspan PSE allows data and power to be transmitted over a category-5 unshielded twisted-paired or twisted-paired cable. It provides continuous data and policy-enabled telephony services by providing 802.3af-draft-compliant PoE over each front-panel RJ-45 port

5 Sample Application - 2 -

6 Parts Names and Functions Front Panel The front panel of the Midspan PSE, displayed below, has 12 pairs of switching ports supported. 1 Power LEDs Glows when the Midspan PSE is powered on. 2 Reset Use a pin-shaped item to reset this device when it is malfunctioning. 3 Console port RS232 Serial Port Connects to the serial port on your PC with the RS- 232 cable. The console port allows you to access the GUI screens and customize your network using the supplied menus and screens. The console port is a DB-9 standard serial port connector. You can use a straight-through DB-9 serial cable (Male/Female) to connect this Midspan PSE with a management station via this port. 4 Port connectors The Midspan PSE uses 12 10BASE-T/100BASE-TX RJ-45 (8-pin modular) port connectors

7 5 Status LED Rear Panel Glows when this Midspan PSE discovers a PD (power device) plugged. Status LED will keep glowing when the PD is successfully powered by this Midspan PSE. Dims when there s no PD detected. Flashes when there is short circuit or over-current being detected. Table2. Parts in the front panel 1 AC Power Connector 2 System Fans/Vents Plug the female end of the provided power cord into this connector, and the male end into the wall outlet. Input voltages ranges from 100 to 120 V. The fans and the vents are used to help cool the Midspan PSE. Always leave two inches of space around the Midspan PSE so that air can circulate and cool the Midspan PSE

8 HARDWARE INSTALLATION The Midspan PSE can be placed directly on your desktop, or mounted in a rack. Desktop Installation To connect the external power source, take the following steps in exactly this order: 1. Plug the cord from the Midspan PSE into the wall outlet. 2. Using the 2-pin connector, plug the external power source into the DC connector receptacle on the back of the Midspan PSE. Rack-Mounting Installation The Midspan PSE may stand alone, or may be mounted in a standard size, 19-inch rack. Rack mounting produces an orderly installation when you have a number of related network devices. The Midspan PSE is supplied with two mounting brackets and screws. These are used for rack mounting the unit. Follow these steps to install the Midspan PSE on a rack: 1. Disconnect all cables from the Midspan PSE before continuing the installation. 2. Attach a mounting bracket to each side of the Midspan PSE with the screws provided. 3. Slide the Midspan PSE into the rack and use the screws provided to secure the Midspan PSE to the rack. 4. Connect the power cord and verify that if the Midspan PSE is receiving adequate power. 5. Reconnect all cables. Connecting Other Power Devices Connect other power devices (PD) to the Midspan PSE with CAT 5 Ethernet cable. Plug one end of the CAT5 cable into one of the Power/Data Connector ports, and the other end into the PD s PoE compatible RJ-45 port

9 HOW TO MANAGE THE MIDSPAN PSE You can configure or monitor this Midspan PSE through the provided GUI utility saved in the included CD. Run the GUI Utility Run the GUI utility provided in the included CD. (Double-click setup.) The installation program will proceed to copy files automatically. Click OK to continue

10 Click the setup button as shown below to start the installation. Click OK to complete the setup. You may now run the utility program to setup your PSE. Go to Start Programs P6012S

11 The GUI Utility will appear the management screen. At the upper left corner of the GUI screen, click the Serial Link Setup tab to set port. Select the COM port of your computer in which you have the device plugged

12 The GUI utility will detect the connection and then the GUI screen will appear. You can have the system always auto refresh by pressing down the Enable Auto Refresh button. A B C D - 9 -

13 Basic GUI Utility Operation The GUI operating page shown in the above figure can be broken down into three major functional operating regions (A to C) and one informational region (D) as described below: A. System Setup & Control Main system level parameters are established in this section. Parameters in this region will be updated after clicking on the Update System Control button. B. System Info The hardware revision code and the version of firmware being run are shown in this region. The state of the Internal sequencer is shown in the Current Port Serviced field. The summation of the total system 48-V power consumption is also shown. C. Port Specific Control Each tab of this section corresponds to each group of 12 ports in the system. A tab can be activated once the Ports in System parameter is set and updated with Update System Control. Parameters that are set for specific ports are updated once the Send Port Control is pressed down. Parametric updates in the parametric region of each port column will auto-refresh if Enable Auto Refresh is pressed down. D. Port Parametric Info

14 Real time and calculated port parameters are displayed in this region. The region to the left allows custom modification of these engineering units through the introduction of alternate gain and offset values. Details as how to set the respective fields shown in the above three functional operating regions (A-C) are separately described in the following sections. A. System Setup & Control Item Ports in System Fault Cycles/Power Cycles Master Enable Line Frequency Rejection Accept Legacy Types (Type 1~4) SW POR MSP 1 Description Number of ports in the system. Reserved component of the power management function in a future firmware release. This enable is AND d with the Port Enable and acts as a global system port on/off control. Sets the PD A/d converter for optimal AD hum rejection. Set the value to the AC power line frequency. Select the Legacy detection type used. Type 1= Accept port capacitance 6o uf < Cp <470uf) Software initiates a reset of the MSP device. 1 MSP: The Micro Controller of the Midspan PSE

15 SW POR TPS 2 Pause P6012S Port LED Direct Write Software initiates a reset of the TPS device. Pause P6012S halts the device. When not selected, the firmware will write port indicator status information directly to the port status LEDs. When selected, the port status LEDs can be controlled directly from the corresponding port LED control of the GUI. PD Discovery R (ohms): PD Discovery resistance limits (Upper/Lower Limit) If the default 802.3af PD discover resistance value limits need to be customized, they can be entered into the upper and lower limit fields. Startup Overload Delay (ms) Enables the current limited overload condition at startup to be extended past 50ms. Enter a value from 1 to 255 msec. P6012S 12C Address (dec) Update System Control Reserved Host 12C port address setting. It is necessary to press this button to enter the values of this frame into the system RAM. The system will then respond to the stored RAM values. 2 TPS: The Midspan PSE Power Manager

16 B. System Info: Item P6012S ID & REV Firmware Ver. Description Displays the version information of this device. Display the accessed version of this device firmware. System Status Current Port Serviced Reserved For the selected 12-port group tab, this parameter displays the present port being accessed by the system internal state sequencer. This value is the summation of all the individual port Total Port Power (W) power consumption in the system. The value is displayed in Watts

17 C. Port Specific Control Item Port Enable Bypass Detection Bypass Classification Description Check to enable the transition of power and data for the specified port. Resistive Legacy/detection is bypassed when checked. When Left un-checked, standard resistive detection is performed. Detection Resistance is shown in the Parametric Field Detection limits are set in the System Field. Prevents classification from being performed in the powering sequence when unchecked. Bypass Power Sampling Prevents power sampling from being performed in the when unchecked. Bypassing sampling decreases system response latency port voltage, current and power are displayed in the Parameter field. Detect Legacy Signature Allows Legacy/Capacitive devices to be detected. Capacitive threshold is 100 uf. Cap value is displayed in the Parameter Field

18 LED Control and Status (LED Output Drive/LED Status Indicators) LED Output Drive: Allows manual LED Control. LED Status Indicators: Port LED Direct Write set LED status as seen at the port is also displayed

19 SPECIFICATIONS Interface Standards Network Interface IEEE802.3af 1x RS-232 serial port, 12 x Power connector ports, 12 x Data connector ports. LED indicators Power Link Input Power Supply AC Input voltage VAC AC Frequency AC Input current Hz 1.39 Amps at 110 VAC Output Power Supply Output voltage 48 VAC (TRP.) Per Port Output Maximum Power Available Total Power Pin Assignment and Polarity 15.4 Watts 120 Watts 4/5(+), 7/8 (-)

20 Powering on two pairs simultaneously Environmental Operating Temperature Storage Temperature Operating Humidity Storage Humidity 0 C to 40 C -20 C to 70 C 5%-95% (20%-90% non-condensing for operation) Maximum 95%, non-condensing Regulatory EMC FCC Part 15, Class B Physical Dimensions Weight 45mm(H) * 440mm(W) * 185mm(D) 2.5 kg