K107A / K107B Half-duplex RS485 serial bus with 3-point insulation

Size: px
Start display at page:

Download "K107A / K107B Half-duplex RS485 serial bus with 3-point insulation"

Transcription

1 0 0 K0 R THE INTERNATIONAL CERTIFICATION NETWORK EN K0A / K0B Half-duplex RS serial bus with -point insulation General Description The K0A and K0B modules are half duplex serial buses with -point insulation. Although both modules feature: Timed automatic direction switching. Communication speeds that can be configured by dip-switch, They differ in the type of interface present on the X side: K0A: RS K0B: RSB Technical features Power supply features Power-supply : Consumption : X-side port characteristics Type: Capacity: Terminator: Protection: Y-side port characteristics Type: Capacity: Terminator: Protection: 9,..0 Vdc max ma at Vdc under normal operating conditions. K0A :RS, K0B: RSB standard nodes for K0A Yes for K0 A, No for K0B Up to 0 Vdc RS half-duplex standard nodes Yes Up to 0 Vdc Description of operation The device usually stays with both its communication ports in reception state (idle status); the first transition (character) detected at one of the ports enables the corresponding communication channel, while the opposing port becomes the data outlet by repeating the stream (data flow) received on the first. Whenever the data flow is interrupted, after a period of time depending on the communication speed set, the device returns to its previous state of reception on both ports (idle status).the time for return to idle status is usually around. characters starting from the reception line's last active status; in any case however, a different period of time can be selected whenever required by protocol. The table below indicates switching times on the basis of the transmission speed set: Speed (bps) Switching time (ms) 0 0, 00 0, 00 0, , 900, 00, 00 00,, Two modules can be used as insulator or repeater for a Full-Duplex connection. In this case, it is useful that the module installed on the master's Tx line inhibit communication direction by selecting either the X->Y direction or the Y->X direction; although switching both dip-switches ON does not cause malfunctions, it inhibits the device with both ports in transmission. Signalling by LED on the front panel LED Meaning Green Led Flashing: data presence at X-port. on X side Steady: inverted connection at X port or X -> Y direction inhibition enabled. Green Led Flashing: data presence at Y-port. on Y side Steady: inverted connection at Y port or Y -> X direction inhibition enabled. Central Green Led A blink of the LED when the device is turned on indicates the presence of voltage. Installation rules This module has been designed for assembly on a DIN rail. Assembly in vertical position is recommended in order to increase the module's ventilation, and no raceways or other objects that compromise aeration must be positioned in the vicinity. Do not position the module above equipment that generates heat; we recommend positioning the module in the lower part of the control panel or container compartment. We recommend rail-type assembly using the corresponding bus connector (Code K-BUS) that eliminates the need to connect the power supply to each module. Inserting the module in the rail -Attach the module in the upper part of the rail. - Press the module downwards. Using the K-BUS connector K0 Removing the module from the rail -Apply leverage using a screwdriver (as shown in the figure). - Rotate the module upwards. - Compose the K-BUS connectors as required in order to obtain the number of positions necessary (each K-BUSpermitstheinsertionofno. modules). - Insert the K-BUS connectors in the rail by positioning them on the upper side of the rail and then rotating them downwards. IMPORTANT: Pay particular attention to the position of the protrudent terminals of the K-BUS. The K-bus must be inserted in the guide with the protrudent terminals on the left (as shown in the figure) otherwise the modules are turned upside downs. - Never connect the power supply directly to the bus connector on the DIN rail.! - Never tap power supply from the bus connector either directly or by using the module's terminals. K0A Serial port electric connections X-side serial port: half-duplex RS Y-side serial port: half-duplex RS A B The use of screened cables is always recommended, and especially whenever the length of the connections is greater than m. A B MI000-I/E ENGLISH - / MI000-I/E ENGLISH - / MI000-I/E ENGLISH - / MI000-I/E ENGLISH - / Signal transmission/processing characteristics Handshake : Timed automatic Insulation : Optical Speed : bps Configuration : by dip-switch Other functions available : X or Y side terminator, X->Y or Y->X communication direction inhibition General Technical Features Insulation voltage : Protection : Environmental conditions : Storage temperature: Dissipation: Signalling by LED : Connections : Wire section : Wire stripping : Box : Dimensions and weight : Reference standards :. kv between each pair of ports IP0 Temperature: -0 + C Humidity: 0 90% non-condensing Altitude: up to 000 m. a. s. l C Lower than 00 mw Data Presence on X port, Data presence on Y port, inverted connection on X port and inverted connection on Y port. Cable clamp terminals and bus (rear connector for DIN and K-BUS bar) 0,.., mm mm PBT, black, x 9, x 0, mm, g. EN000--/00 (electromagnetic emission, industrial environment) EN000--/00 (electromagnetic immunity, industrial environment) EN00-/00 (safety). All circuits must be insulated from the other circuits under dangerous voltage with double insulation. The power supply transformer must comply with EN0: Insulated transformers and safety transformers. DIP-SWITCH SETTINGS Both the K0 A and K0 B modules can be completely configured by dip-switches. The meaning of the possible dip-switch settings is provided below. In all the following tables, the indication means that the DIP-switch is set in (ON); whenever no such indication is provided, it means that the DIP-switch is set in 0 (OFF). X->Y DIRECTION INHIBITION SW Y Terminator SW Transmission speed SW Y->X DIRECTION INHIBITION SW X Terminator (only for the K0A) SW Polarizer * (only for the RS of the K0 B) SW * When installed, the polarizer prevents the RS line from capturing noise when left disconnected Electrical Connections 0,.., mm mm Power supply There are various ways to provide the K Series modules with power. - Direct power supply to the modules by connecting Vdc power supply directly to Terminals (+)and (-)of each module. The module has been designed for spring-type terminal electrical connections. Proceed as follows to make the connections: - Strip the cables by 0. mm - Insert a screwdriver in the square hole and press it until the cable lock spring opens. - Insert the cable in the round hole. - Remove the screwdriver and make sure that the cable is tightly fastened in the terminal Vdc - - Using the K-BUS connector accessory for the distribution of the power supply to the modules via bus connector, in this way eliminating the need to connect power supply to each module. The bus can be supplied from any of the modules; the total absorption of the bus must be less than 00 ma. Higher absorption values can damage the module. An appropriately sized fuse must be connected in series to the power supply. - Using the K-BUS connector accessory for the distribution of the power supply to the modules via bus connector and the K- accessory for the connection of the power supply. The K- accessory is a. mm wide module that contains a set of protections designed to protect the modules connected via bus against over-voltage loads. The bus connector can be provided with power using the K- module if the total absorption of the bus is less than. A. Higher absorption values can damage both the module and the bus. An appropriately sized fuse must be connected in series to the power supply. K0B Serial port electric connections X-side serial port: half-duplex RS Y-side serial port: half-duplex RS A B The use of screened cables is always recommended, and especially whenever the length of the connections is greater than m This document is property of SENECA srl. Duplication and reprodution are forbidden, if not authorized. Contents of the present documentation refers to products and technologies described in it. All technical data contained in the document may be modified without prior notice Content of this documentation is subject to periodical revision. ISO Tx (out) Rx (in) PC Serial Port SENECA s.r.l. Via Germania, - - Z.I. CAMIN - PADOVA - ITALY Tel Fax info@seneca.it MI000-I/E ENGLISH - / MI000-I/E ENGLISH - / MI000-I/E ENGLISH - / MI00000-I/E ENGLISH - /

2 ASYNCHRONOUS SERIAL CONVERTER RS/USB S0USB/K0USB GENERAL DESCRIPTION The S0USB and K0USB instruments, represent an interface able to implement an asynchronous RS serial port, by using an USB port present on the PC. Thanks to the provided driver, the serial interface is considered by the operating system as a standard serial port; so the use of the product is directly allowed through any software able to communicate with the standard serial ports of the operating system (COM, COM, etc). The electrical insulation between the RS and the USB ports, allows to remove many problems of electrical noise which may occur when the connected equipment is very far from the PC. GENERAL FEATURES Usable in Windows 9, 000 and XP Environments. Usable in Linux Environment with Kernel..0 or later, for which the direct support exists. Compatible with. and.0 USB standard port. Insulation between USB and RS: 00 V. Max Consumption: 0 ma. Power Supply provided from the USB port of the PC. Terminator of RS line, settable through an external bridge. Baudrate: 00 bps)00 bps. RS Serial communication through MODBUS RTU protocol, nodes max. Possibility of multiple connection of more S0USB or K0USB to the same PC. Three leds to view the status of the module s activity. Accessories: CD with driver. USB connection cable: USB A and MINI USB B connectors. RS Connections of S0USB: removable -way screw terminals. RS Connections of K0USB: Spring terminals, Conductor Section: 0... mm, Wire stripping: mm. Environmental conditions: Temperature: -0.. C. Humidity: 0%..90% non-condensing. Installation Category: II. Pollution Degree. Storage Temperature: -0.. C Protection Index: IP0 Weight, Dimensions: Standards: TECHNICAL SPECIFICATIONS S0USB: g, 0 x x 0, mm K0USB: g,, x 9, x 0, mm EN000--/00 (electromagnetic emission, industrial environment) EN000--/00 (electromagnetic immunity, industrial environment) EN00-/00 (safety). INSTALLATION RULES S0USB INSTALLATION RULES For S0USB module there are not particular warnigs, we only advise to use screened cables for the RS line in case of long connections or noisy environments (refer to Electrical Connections section). MI000 Pagina of

3 K0USB INSTALLATION RULES This module has been designed for mounting on a DIN rail. Assembly in vertical position is recommended in order to increase the module's ventilation, and no raceways or other objects that compromise aeration must be positioned in the vicinity. Do not position the module above equipment that generates heat; we recommend positioning the module in the lower part of the control panel or container compartment. Inserting the module in the rail Removing the module from the rail ) Attach the module in the upper part of the rail. ) Press the module downwards. ) Apply leverage using a screwdriver (as shown in the figure). ) Rotate the module upwards. In case of long connections or noisy environments, it is advisable to use screened cables for the RS line (refer to Electrical Connections section). ELECTRICAL CONNECTIONS S0USB ELECTRICAL CONNECTIONS The following figure shows the electrical connections for S0USB module. By inserting an external bridge between T and T terminals, the terminator of the RS line is inserted. In case of long connections or noisy environments, it is advisable to use screened cables for the RS line. MI000 Pagina of

4 K0USB ELECTRICAL CONNECTIONS The following figure shows the electrical connections for K0USB module. By inserting an external bridge between T and T terminals, the terminator of the RS line is inserted. In case of long connections or noisy environments, it is advisable to use screened cables for the RS line. Terminals Connections The module has been designed for spring-type terminal electrical connections. Proceed as follows to make the connections: - Strip the cables by 0. mm - Insert a screwdriver in the square hole and press it until the cable lock spring opens. - Insert the cable in the round hole. - Remove the screwdriver and make sure that the cable is tightly fastened in the terminal. MI000 Pagina 9 of

5 LEDS SIGNALLING Both the modules have three leds which allow to visualize the status of the module s activity. LEDS POSITION ON S0USB On S0USB module, the leds are positioned on the following way: LEDS POSITION ON K0USB On K0USB module, the leds are positioned on the following way: LEDS MEANING On both modules the leds are identified with the same name and have the following meaning: NAME COLOUR MEANING Yellow If it is lighted, it indicates that the instrument is correctly supplied. Rx Red It lights when the module receives data through the RS port. Tx Red It lights when the module transmits data through the RS port. MI000 Pagina 0 of

6 PROBLEMS SOLVING For any problems with the converter, verify the following points: PROBLEM The Led does not light The Rx Led is steady on The received data are not correct VERIFY Verify that the USB port of the PC provides the V which are necessary to supply the module. Verify that the RS cables have not been swapped. Verify the communication speed. DRIVER INSTALLATION The CD containing the instrument s driver is provided to the user. In this section the installation procedure of the driver will be briefly described. It is necessary to specify that the installation in Linux (with Kernel..0 or later) environments is automatic and does not need the CD with the driver. The standard serial port of the PC which identifies the device is the following: /dev/ttyusb0. As regards Windows operating systems, it is important to underline that the procedure is divided into two phases which are both fundamental for the final use of the instrument. On the first phase, the driver of the out-and-out serial converter is installed. By the second phase instead the virtual driver will be installed: this will allow to use the peripheral as a standard serial port of the operating system. If case of use of Windows 000, these two phases are identical and are performed step by step: the user has only to follow the guided procedure; instead in Windows 99 the second phase is automatically managed by the operating system without any further dialogue with the user. In Windows XP the two phases are performed very quickly by the operating system if it the CD with the drivers has been inserted. For the correct installation it is important to insert the CD with the driver and connect the device to the PC already turned on, so that the operating system may automatically detect the presence of the device. At this point the the user has only to follow the guided installation. VISUALIZATION OF THE VIRTUAL COM PORT At the end of the installation, it is possibile to view the name which has been assigned to the virtual serial port associated to the used S0USB or K0USB device. For example on the following Device Manager panel, it has been identified as COM: MI000 Pagina of

7 SENECA s.r.l. Via Germania, - Z.I. CAMIN - PADOVA - ITALY Tel Fax info@seneca.it MI000 Pagina of

ASYNCHRONOUS SERIAL CONVERTER RS485/USB S107USB/K107USB

ASYNCHRONOUS SERIAL CONVERTER RS485/USB S107USB/K107USB ASYNCHRONOUS SERIAL CONVERTER RS485/USB S107USB/K107USB GENERAL DESCRIPTION The S107USB and K107USB instruments, represent an interface able to implement an asynchronous RS485 serial port, by using an

More information

K-LINE. USB RS485 Asynchronous Converter CONVERTERS AND INTERFACES. Serial Converters

K-LINE. USB RS485 Asynchronous Converter CONVERTERS AND INTERFACES. Serial Converters CONVERTERS AND INTERFACES K-LINE USB RS485 Asynchronous Converter Serial Converters FUNCTION: Connect an RS-485 Network to the USB Port Speed selectable from 1.200 bps to 250 Kbps Compatible with standard

More information

Product EASY-USB. Description. USB - UART TTL converter. Seneca s.r.l. Series of product. Pag.

Product EASY-USB. Description. USB - UART TTL converter. Seneca s.r.l.    Series of product. Pag. INSTALLATION AND USER S GUIDE Language manual Product English EASY-USB Description USB - UART TTL converter Series of product Contents: 1.0 Disclaimer.0 Description and general specifications Pag..1 Description.

More information

S SENECA. Installation Manual Z-TWS4. Z-PC Line. Web Multifunction Controller Straton / Linux

S SENECA. Installation Manual Z-TWS4. Z-PC Line. Web Multifunction Controller Straton / Linux S SENECA Z-PC Line EN Installation Manual Contents: - General specifications - Technical features - Modbus and CANopen connections - Installation rules - Electrical connections - LEDs signallings - Default

More information

Strain Gauge Converter

Strain Gauge Converter EN Z-SG General Description Module Z-SG is a strain gauge signal converter. Measurements taken using the 6-wires or 4-wires technique are available through Modbus-RTU serial protocol or the analog output.

More information

RS232/USB and TTL/USB ASYNCRONOUS SERIAL CONVERTER CB CONFIG BOX

RS232/USB and TTL/USB ASYNCRONOUS SERIAL CONVERTER CB CONFIG BOX RS232/USB and TTL/USB ASYNCRONOUS SERIAL CONVERTER CB CONFIG BOX GENERAL DESCRIPTION CB CONFIG BOX is a converter that realizes a serial asyncronous connection via RS232 or TTL, using an USB port on the

More information

RS232/USB, TTL/USB and RS485/USB ASYNCRONOUS SERIAL CONVERTER CONFIG BOX PLUS

RS232/USB, TTL/USB and RS485/USB ASYNCRONOUS SERIAL CONVERTER CONFIG BOX PLUS RS232/USB, TTL/USB and RS485/USB ASYNCRONOUS SERIAL CONVERTER CONFIG BOX PLUS GENERAL DESCRIPTION CONFIG BOX PLUS is a converter that realizes a serial asyncronous connection via RS232, RS485 or TTL, using

More information

USER MANUAL Z-8NTC 8 CHANNELS NTC TEMPERATURE SENSOR CONVERTER WITH USB / RS485 PORT AND MODBUS RTU PROTOCOL

USER MANUAL Z-8NTC 8 CHANNELS NTC TEMPERATURE SENSOR CONVERTER WITH USB / RS485 PORT AND MODBUS RTU PROTOCOL USER MANUAL Z-8NTC 8 CHANNELS NTC TEMPERATURE SENSOR CONVERTER WITH USB / RS485 PORT AND MODBUS RTU PROTOCOL SENECA S.r.l. Via Austria 26 35127 Z.I. - PADOVA (PD) - ITALY Tel. +39.049.8705355 8705355 Fax

More information

CEM M-RS485 INSTRUCTION MANUAL (M014B A)

CEM M-RS485 INSTRUCTION MANUAL (M014B A) Communications interface CEM M-RS485 INSTRUCTION MANUAL (M014B01-03-14A) 2 SAFETY PRECAUTIONS Follow the warnings described in this manual with the symbols shown below. DANGER Warns of a risk, which could

More information

INSTALLATION MANUAL Z-UMTS

INSTALLATION MANUAL Z-UMTS INSTALLATION MANUAL Datalogger HSPA + with built-in I/O, telecontrol functions, embedded UPS and advanced programming language EN SENECA s.r.l. Headquarters: Via Austria, 26 35127 PADOVA ITALY Phone +39.049.8705355-8705359

More information

Language of the manual

Language of the manual USER S MANUAL INSTALLATION AND Language of the manual Product English Single-phase switching power supply: 24V @ 1.5A Description Contents: 1.0 Disclaimer 2.0 Description and General features Page 2 2

More information

S401-L Panel Mounting Indicator with OLED data Display.

S401-L Panel Mounting Indicator with OLED data Display. EN S401-L Panel Mounting Indicator with OLED data Display. 1. GENERAL SPECIFICATIONS The S401-Lmodule is a panel mounting indicator with OLED data display. The module has two RS485 serial ports, both supporting

More information

ICF-1150 Series Quick Installation Guide

ICF-1150 Series Quick Installation Guide ICF-1150 Series Quick Installation Guide Second Edition, March 2012 2012 Moxa Inc. All rights reserved. P/N: 1802011500011 Overview Introduction The ICF-1150 series fiber converters are equipped with a

More information

ICF-1150 Series Quick Installation Guide

ICF-1150 Series Quick Installation Guide ICF-1150 Series Quick Installation Guide Fifth Edition, July 2015 2015 Moxa Inc. All rights reserved. P/N: 1802011500014 1802011500014 Overview Introduction ICF-1150 series fiber converters have a multi-interface

More information

SENECA s.r.l. Commercial

SENECA s.r.l. Commercial INSTALLATION MANUAL EN Serie Z PC INDUSTRIAL MODEM /GPRS Quadband CHAPTER INDEX 1. PRELIMINARY WARNINGS 2. DESCRIPTION AND CHARACTERISTICS 2.1 Module description 2.2 General characteristics 3. TECHNICAL

More information

ELSETA IOMOD 8DI8DO. User manual. Elseta 3/2017 V1.0

ELSETA IOMOD 8DI8DO. User manual. Elseta 3/2017 V1.0 ELSETA User manual Elseta 3/2017 V1.0 COPYRIGHTS AND TRADEMARKS Elseta is UAB Aedilis trademark that identifies UAB Aedilis manufactured products. All of the products copyright belongs to "Aedilis. These

More information

UNIVERSAL CURRENT CONVERTER

UNIVERSAL CURRENT CONVERTER UNIVERSAL CURRENT / VOLTAGE CONVERTER AC/DC Current / Voltage Analyzer The is the first CURRENT / VOLTAGE CONVERTER & ANALYZER ALL IN ONE - of the market. It allow you to connect all isolated current sensors.

More information

USB/RS-485 INTERFACE CONVERTER PD10 TYPE USER S MANUAL

USB/RS-485 INTERFACE CONVERTER PD10 TYPE USER S MANUAL USB/RS-485 INTERFACE CONVERTER PD10 TYPE USER S MANUAL Contents 1. APPLICATION... 5 2. CONVERTER SET... 5 3. CONVERTER INSTALLATION... 6 3.1. Converter installation and safety requirements... 6 3.2. Description

More information

DCC-8 DIGITAL TO EIGHT CURRENT LOOP CONVERTER OPERATING MANUAL

DCC-8 DIGITAL TO EIGHT CURRENT LOOP CONVERTER OPERATING MANUAL DCC-8 DIGITAL TO EIGHT CURRENT LOOP CONVERTER OPERATING MANUAL 1 TABLE OF CONTENTS 1. MOUNTING INSTRUCTIONS 1.1 Standard DIN Rail mounting 1.2 Screw Mounting 2. FUSE REPLACEMENT 3. ASSEMBLING THE UNIT

More information

MED102A. Industrial Serial to Single-mode Fiber Converter

MED102A. Industrial Serial to Single-mode Fiber Converter MED102A - 0708 pg. 1 / 5 MED102A Industrial Serial to Single-mode Fiber Converter Data Rates up to 115.2 kbps 9 Mile (15 km) Range 10 to 48 VDC Input Voltage Wide Operating Temperature 2000V Isolation

More information

MINI MCR-SL-UI-2I. Configurable signal duplicator. Data sheet. 1 Description

MINI MCR-SL-UI-2I. Configurable signal duplicator. Data sheet. 1 Description Configurable signal duplicator Data sheet 102382_en_03 PHOENIX CONTACT 2012-05-02 1 Description The MINI MCR-SL-UI-2I(-SP)(-NC) configurable signal duplicator is used to electrically isolate, condition,

More information

ICD105A 1008 page 1/ r001 ICD105A. Industrial RS-232 to RS-422/485 Converter

ICD105A 1008 page 1/ r001 ICD105A. Industrial RS-232 to RS-422/485 Converter ICD105A 1008 page 1/5 7319 r001 ICD105A Industrial RS-232 to RS-422/485 Converter Data Rates up to 115.2 Kbps 10 48 VDC Input Power Range Wide Operating Temperature 3-Way 2000V Optical Isolation Modbus

More information

TCF-142 Quick Installation Guide

TCF-142 Quick Installation Guide TCF-142 Quick Installation Guide Edition 15.0, February 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777 Fax: 1-714-528-6778

More information

PTC-101-M12 Hardware Installation Guide

PTC-101-M12 Hardware Installation Guide PTC-101-M12 Hardware Installation Guide Moxa Industrial Media Converter Third Edition, May 2014 2014 Moxa Inc. All rights reserved. P/N: 1802001016021 Overview The PTC-101-M12 industrial media converter

More information

Advanced GSM/GPRS device for the telecontrol

Advanced GSM/GPRS device for the telecontrol S SENECA EN MyALARM2-2 Advanced GSM/GPRS device for the telecontrol Installation Manual Contents: - General features - Technical specifications - Installation - Constructive elements - Terminal connections

More information

Modbus Digital Remote I/O. ARM Series. Modbus Sensor Connector Type Digital Remote I/O. Features. User Manual For Communication. Ordering Information

Modbus Digital Remote I/O. ARM Series. Modbus Sensor Connector Type Digital Remote I/O. Features. User Manual For Communication. Ordering Information RM Series Modbus Digital Remote I/O Modbus Connector Type Digital Remote I/O Features Modbus RTU standard protocol Connects with sensor connector, e-con: saves wiring work (sensor connector, CNE Series,

More information

AI561 Analog Input Module

AI561 Analog Input Module Ordering Data DATA SHEET AI561 Analog Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R1101 AI561, analog input module, 4 AI, U/I 1TNE 968 901 R3101 1TNE 968

More information

TCF-142-RM Series Hardware Installation Guide

TCF-142-RM Series Hardware Installation Guide TCF-142-RM Series Hardware Installation Guide Third Edition, March 2015 2015 Moxa Inc. All rights reserved. P/N: 1802001420622 *1802001420622* Overview Introduction The TCF-142-RM series fiber converters

More information

INSTALLATION MANUAL. VPN Industrial Gateway, Serial Device Server, Router 3G+ /4G, GPS and built-in I/O s

INSTALLATION MANUAL. VPN Industrial Gateway, Serial Device Server, Router 3G+ /4G, GPS and built-in I/O s INSTALLATION MANUAL Z-PASS2 - IO VPN Industrial Gateway, Serial Device Server, Router 3G+ /4G, GPS and built-in I/O s Z-PASS2-S - IO VPN RTU IEC61131, IDE Straton, Router 3G+ / 4G, GPS and built-in I/O

More information

ADAM-4510 RS-422/RS-485 Repeater ADAM-4510S Isolated RS-422/485 Repeater ADAM-4520 Isolated RS-422/485 Converter Startup Manual

ADAM-4510 RS-422/RS-485 Repeater ADAM-4510S Isolated RS-422/485 Repeater ADAM-4520 Isolated RS-422/485 Converter Startup Manual ADAM-510 RS-/RS-85 Repeater ADAM-510S Isolated RS-/85 Repeater ADAM-50 Isolated RS-/85 Converter Startup Manual Packing List Before you begin installing your module, please make sure that the following

More information

IMC-21 Quick Installation Guide

IMC-21 Quick Installation Guide IMC-21 Quick Installation Guide Moxa Industrial Media Converter Edition 5.0, February 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

VirtualSCADA VSU-485G USB to RS422/485 Isolated Converter User Manual

VirtualSCADA VSU-485G USB to RS422/485 Isolated Converter User Manual VirtualSCADA USB to RS422/485 Isolated Converter User Manual Revision 1.01.00 Page 1 (15) Table of contents Warranty and support... 3 Product return... 3 1 About the VirtualSCADA USB to RS422/485 Converter...

More information

DIRIS Digiware D and C Communication and control power interfaces

DIRIS Digiware D and C Communication and control power interfaces Multi-circuit metering and measurement diris-dw_006_a_us_cat diris-dw_142_a The solution for > Industry > Building > Infrastructure > Data centers DIRIS D-40/D-50/D-70 Centralization and display of data

More information

Industrial Serial RS-232 to Fiber Converter. KSC-200 Series. Installation Guide

Industrial Serial RS-232 to Fiber Converter. KSC-200 Series. Installation Guide Industrial Serial RS-232 to Fiber Converter KSC-200 Series Installation Guide DOC.100803-KSC-200-1- (C) 2006 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any

More information

USER S MANUAL TP series

USER S MANUAL TP series USER S MANUAL TP1043 02 series ME7056_06 07/18 TP1043 02 INDEX 1. Introduction... 1 1.1. Staff skill... 1 1.2. Simbols... 1 1.3. Terms... 2 1.4. Security... 2 1.5. REFERENCE MANUAL... 2 2. System description...

More information

PTC-101 Quick Installation Guide

PTC-101 Quick Installation Guide PTC-101 Quick Installation Guide Moxa Industrial Media Converter Edition 5.1, November 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

OTB1S0DM9LP I/O distributed module OTB - Modbus non isolated serial link m

OTB1S0DM9LP I/O distributed module OTB - Modbus non isolated serial link m Characteristics I/O distributed module OTB - Modbus non isolated serial link - 0..10 m Complementary Topology Bus length Main Number of devices per segment 0...32 Data format Parity Discrete input voltage

More information

TN-5308 Quick Installation Guide

TN-5308 Quick Installation Guide TN-5308 Quick Installation Guide Moxa ToughNet Switch Edition 6.0, February 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

Industrial 3-Port Fast Ethernet Media Converter Switches

Industrial 3-Port Fast Ethernet Media Converter Switches Industrial 3-Port Fast Ethernet Media Converter Switches KSD-103-A series KSD-103-B series Installation Guide DOC.081111 1/20 (C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation

More information

Installation Instructions

Installation Instructions Installation Instructions (Cat. No. 1794-PS1) 1 2 3 4 5 7 6 Component Identification 1 Supply module 1794-PS1 2 Indicator 3 120/230V ac ground 4 120/230V ac common L2/N connections 5 120/230V ac power

More information

MINI MCR-SL-UI-2I-NC. Extract from the online catalog. Order No.:

MINI MCR-SL-UI-2I-NC. Extract from the online catalog. Order No.: Extract from the online catalog MINI MCR-SL-UI-2I-NC Order No.: 2864176 4-way signal duplicator for electrical isolation and duplication of analog signals with screw connection, standard configuration

More information

XPSMF35. Product data sheet Characteristics. Preventa safety PLC compact - Profibus DP protocol. Main. Complementary. Safety module name

XPSMF35. Product data sheet Characteristics. Preventa safety PLC compact - Profibus DP protocol. Main. Complementary. Safety module name Product data sheet Characteristics XPSMF3542 Preventa safety PLC compact - Profibus DP protocol Main Range of product Product or component type Safety module name Safety module application Nov 13, 2018

More information

RAD-DO8-IFS. I/O extension module, eight digital transistor outputs. Data sheet. 1 Description

RAD-DO8-IFS. I/O extension module, eight digital transistor outputs. Data sheet. 1 Description I/O extension module, eight digital transistor outputs Data sheet 105364_en_00 PHOENIX CONTACT 2013-03-26 1 Description The I/O extension module can be used in conjunction with Radioline wireless modules

More information

3 CH Analog Output module / CANopen

3 CH Analog Output module / CANopen 3 CH Analog Output module / CANopen Power Supply 1..4 Vdc, 19..28 Vac Isolation 1,5 kvac (5 way) Accuracy,5% A/D resolution 14 bit Channels 3 Voltage range 1 V Current range..2, 4..2 ma RPDO < 2 ms (-1%

More information

Mini Energy Web Server

Mini Energy Web Server 87045 LIMOGES Cedex Telephone : 05 55 06 87 87 Fax: 05 55 06 88 88 Mini Energy Web Server Contents Pages 1. Description - Use... 1 2. Range... 1 3. Overall dimensions... 1 4. Preparation - Connection...

More information

INJ-24A Series Quick Installation Guide

INJ-24A Series Quick Installation Guide INJ-24A Series Quick Installation Guide Moxa High-Power PoE+ Injector Edition 4.1, August 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

CEM M-ETH INSTRUCTION MANUAL (M060B A)

CEM M-ETH INSTRUCTION MANUAL (M060B A) Communications interface CEM M-ETH INSTRUCTION MANUAL (M060B01-03-14A) 2 SAFETY PRECAUTIONS Follow the warnings described in this manual with the symbols shown below. DANGER Warns of a risk, which could

More information

USB RS-485/422 Communication adapter virtual serial port ELO E211. Operation manual

USB RS-485/422 Communication adapter virtual serial port ELO E211. Operation manual USB RS-485/422 Communication adapter virtual serial port Virtual IDLE ECHO ON OFF COM to Fiber Optics through USB ELO E211 Operation manual 2 ELOE211ZKE001 1.0 Introduction 4 1.1 Use of the converter 4

More information

DI572 Digital Input Module

DI572 Digital Input Module Ordering Data DATA SHEET DI572 Digital Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 230 500 R0000 1TNE 968 901 R3101 1TNE 968 901 R3102 1TNE 968 901 R3103 1TNE 968

More information

USER S MANUAL TP1043 series

USER S MANUAL TP1043 series USER S MANUAL series ME7029_04 06/15 INDEX 1. Introduction... 1 1.1. Staff skill... 1 1.2. Simbols... 1 1.3. Terms... 2 1.4. Security... 2 1.5. REFERENCE MANUAL... 2 2. System description... 2 2.1. Specification...

More information

Island bus expansion module

Island bus expansion module s 8 184 8184P01 TX-I/O Island bus expansion TXA1.IBE Expand island bus to a distance of up to 2 x 200 meters Compact design per DIN 43 880, requires little space Easy installation and setup Mounted on

More information

485DRCI. Industrial RS-232 to RS-422/485 Converter B&B ELECTRONICS PRODUCT INFORMATION. Specifications Serial Technology

485DRCI. Industrial RS-232 to RS-422/485 Converter B&B ELECTRONICS PRODUCT INFORMATION. Specifications Serial Technology 485DRCI RS-232 RS-485 2-Wrie RS-422/485 4-Wire RS-232 CON. RS-422/485 CON. Data Rate Isolation Surge Protection Industrial Bus Source Input Voltage Power Consumption Connector p/n 7207r3 485DRCI-4108ds

More information

Operating Manual UMB ISO Converter ISOCON Order Number: 8160.UISO

Operating Manual UMB ISO Converter ISOCON Order Number: 8160.UISO Order Number: 8160.UISO Status: V3; 17.09.2010c G. Lufft Mess- und Regeltechnik GmbH, Fellbach, Germany 1 TABLE OF CONTENTS PLEASE READ BEFORE USE... 3 DESCRIPTION... 5 UMB ISO CONVERTER ISOCON... 6 CONFIGURATION...

More information

MOXA Industrial Media Converter

MOXA Industrial Media Converter MOX Industrial Media Converter IMC-1 Hardware Installation Guide First Edition, September 005 Moxa Networking Co., Ltd. Tel: +886--910-130 Fax: +886--910-131 www.moxa.com support@moxanet.com (Worldwide)

More information

USB to RS232 Converter USB-013 (Rev3) User s Manual Ver. 1.2 HuMANDATA LTD.

USB to RS232 Converter USB-013 (Rev3) User s Manual Ver. 1.2 HuMANDATA LTD. USB to RS232 Converter USB-013 (Rev3) User s Manual Ver. 1.2 HuMANDATA LTD. Table of Contents Precautions... 1 Revision History... 2 Introduction... 2 1. Overview... 3 2. Power Supply... 3 3. Specifications...

More information

MINI MCR-SL-PT100-UI-200

MINI MCR-SL-PT100-UI-200 Configurable temperature transducer for PT00 INTERFACE Data sheet 078_en_0 PHOENIX CONTACT 00-0-5 Description The MINI MCR-SL-PT00-UI-00... is a configurable -way isolated temperature transducer. It is

More information

DI561 Digital Input Module

DI561 Digital Input Module Ordering Data DATA SHEET DI561 Digital Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R2101 1TNE 968 901 R3101 1TNE 968 901 R3103 1TNE 968 901 R3105 DI561, digital

More information

XPSMF40. Main. Safety module name. Monitoring safety detection discrete input Monitoring safety dialogue discrete output

XPSMF40. Main. Safety module name. Monitoring safety detection discrete input Monitoring safety dialogue discrete output Product datasheet Characteristics XPSMF4000 Preventa safety PLC compact - Safe Ethernet Main Range of product Product or component type Safety module name Safety module application Preventa Safety automation

More information

OTB1S0DM9LP I/O distributed module OTB - Modbus non isolated serial link m

OTB1S0DM9LP I/O distributed module OTB - Modbus non isolated serial link m Characteristics I/O distributed module OTB - Modbus non isolated serial link - 0..10 m Product availability : Stock - Normally stocked in distribution facility Price* : 494.00 USD Main Range of product

More information

AO561 Analog Output Module

AO561 Analog Output Module Ordering Data DATA SHEET AO561 Analog Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R1201 AO561, analog output module, 2 AO, U/I 1TNE 968 901 R3102 Terminal

More information

DX561 Digital Input/Output Module

DX561 Digital Input/Output Module Ordering Data DATA SHEET DX561 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R2301 1TNE 968 901 R3101 DX561, digital input/output module, 8 DI

More information

MINI MCR-SL-CVS NC

MINI MCR-SL-CVS NC Constant voltage source Data sheet 105264_en_01 PHOENIX CONTACT 2013-04-03 1 Description Configurable constant voltage source for generating highprecision constant voltages. The voltage supply is also

More information

CONVERTER OF RS-232/RS-485 INTERFACES PD51 TYPE USER S MANUAL

CONVERTER OF RS-232/RS-485 INTERFACES PD51 TYPE USER S MANUAL CONVERTER OF RS-232/ INTERFACES PD51 TYPE USER S MANUAL 1 2 CONVERTER OF RS-232/ INTERFACES PD51 TYPE USER S MANUAL CONTENTS 1. APPLICATION... 5 2. CONVERTER SET... 5 3. INSTALLATION OF PD51-A TYPE...

More information

TP32MTT.03 TP32MTT [ GB ] Probes for soil thermal profile measurement

TP32MTT.03 TP32MTT [ GB ] Probes for soil thermal profile measurement TP32MTT.03 [ GB ] Probes for soil thermal profile measurement [ GB ] [ GB ] Description Temperature measurement at 7 levels (TP32MTT.03) or 6 levels () In accordance with the requirements of the World

More information

MINI MCR-SL-UI-REL(-SP)

MINI MCR-SL-UI-REL(-SP) Configurable Threshold Value Switch Data Sheet 11/2004 Method of Operation The configurable 3-way threshold value switch MINI MCR-SL-UI-REL(-SP) is used to control and monitor analog standard signals.

More information

EMS CX 3 - Modbus/EMS Interface

EMS CX 3 - Modbus/EMS Interface 87045 LIMOGES Cedex Telephone : 05 55 06 87 87 Fax: 05 55 06 88 88 EMS CX 3 - Modbus/EMS Interface Contents Pages 1. Description - Use... 1 2. Range... 1 3. Overall dimensions... 1 4. Preparation - Connection...

More information

DC562, digital input/output module,

DC562, digital input/output module, Ordering Data DATA SHEET DC562 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 231 900 R0000 1TNE 968 901 R3101 1TNE 968 901 R3102 1TNE 968 901 R3103 1TNE

More information

INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS. KCD-400 Series. Installation Guide

INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS. KCD-400 Series. Installation Guide INDUSTRIAL 1000BASE-T TO 1000BASE-X MEDIA CONVERTERS KCD-400 Series Installation Guide DOC.060227-KCD-400-1- (C) 2005 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced

More information

ELSETA IOMOD 8DI8DO. User manual. Elseta V1.0

ELSETA IOMOD 8DI8DO. User manual. Elseta V1.0 ELSETA IOMOD 8DI8DO User manual Elseta V1.0 /2017 COPYRIGHTS AND TRADEMARKS Elseta is UAB Aedilis trademark that identifies UAB Aedilis manufactured products. All of the products copyright belongs to "Aedilis.

More information

EDS-G308 Series Quick Installation Guide

EDS-G308 Series Quick Installation Guide EDS-G308 Series Quick Installation Guide Moxa EtherDevice Switch Edition 6.1, September 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

OTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP m

OTB1E0DM9LP I/O distributed module OTB - Ethernet TCP/IP m Characteristics I/O distributed module OTB - Ethernet TCP/IP - 0..100 m Main Range of product Product or component type Integrated connection type Mar 31, 2018 Modicon OTB I/O distributed module Discrete

More information

XPSMCMCO0000EM Modbus TCPIP diagnostic expansion module with screw term

XPSMCMCO0000EM Modbus TCPIP diagnostic expansion module with screw term Characteristics Modbus TCPIP diagnostic expansion module with screw term Main Range of product Product or component type Device short name [Us] rated supply voltage Complementary Power dissipation in W

More information

CMU 100 RS485 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star Coupler User Manual

CMU 100 RS485 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star Coupler User Manual CMU 100 RS485 to 7x, 6x, 5x, 4x Multimode Fiber Optic Star Coupler User Manual CMU 100 / 2.5.6.6.6.6.6.6.6 12, CMU 100 / 8.5.6.6.6.6.6.6.6 12, CMU 100 / 2.5.6.6.6.6.6.6 12, CMU 100 / 8.5.6.6.6.6.6.6 12,

More information

CAN Repeater CAN-CR200, CAN-CR220, CAN-CR210/FO

CAN Repeater CAN-CR200, CAN-CR220, CAN-CR210/FO Hardware Manual CAN Repeater CAN-CR200, CAN-CR220, CAN-CR210/FO The expert for industrial and automotive communication IXXAT Headquarter US Sales Office IXXAT Automation GmbH IXXAT Inc. Leibnizstr. 15

More information

USER MANUAL Z-SG / Z-SG-L. Advanced Digital Strain gauge converter. Via Austria, PADOVA ITALY

USER MANUAL Z-SG / Z-SG-L. Advanced Digital Strain gauge converter. Via Austria, PADOVA ITALY USER MANUAL Z-SG / Z-SG-L Advanced Digital Strain gauge converter SENECA s.r.l. Via Austria, 26 35127 PADOVA ITALY Tel. +39.049.8705355 8705359 Fax. +39.049.8706287 Web site: www.seneca.it Technical assistance:

More information

DIGITAL CLOCK. DLZ Type. Service manual

DIGITAL CLOCK. DLZ Type. Service manual DIGITAL CLOCK DLZ Type Service manual Table of contents: 1. APPLICATION...5 2. CLOCK KIT...5 3. BASIC REQUIREMENTS AND OPERATIONAL SAFETY INSTRUCTIONS...5 4. CONSTRUCTION AND INSTALLATION...6 5. ELECTRICAL

More information

Moxa Industrial Media Converter PTC-101-M12 Hardware Installation Guide

Moxa Industrial Media Converter PTC-101-M12 Hardware Installation Guide Moxa Industrial Media Converter PTC-101-M12 Hardware Installation Guide First Edition, February 2012 2012 Moxa Inc. All rights reserved. P/N: 1802001016020 Overview Moxa Industrial Media Converter, which

More information

TRP-C08. USB to RS232/422/485 Isolated Converter. User s Manual. Printed Sep.2014 Rev 1.4

TRP-C08. USB to RS232/422/485 Isolated Converter. User s Manual. Printed Sep.2014 Rev 1.4 TRP-C08 USB to RS232/422/485 Isolated Converter User s Manual Printed Sep.2014 Rev 1.4 Trycom Technology Co.,Ltd No.35, Zhongxing Rd., Guishan Township, Taoyuan County 333, Taiwan. Tel : 886-3-350-3351

More information

TCNM-ACBB1 Installation Manual

TCNM-ACBB1 Installation Manual The TCNM-ACBB1 is a connection box that can be used as an accessory to facilitate system connections for installation and device replacement of several Banner family reading devices. System cabling is

More information

EDS-G205A-4PoE Quick Installation Guide

EDS-G205A-4PoE Quick Installation Guide EDS-G205A-4PoE Quick Installation Guide Moxa EtherDevice Switch Edition 4.1, June 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

DC561, digital input/output module,

DC561, digital input/output module, Ordering Data DATA SHEET DC561 Digital Input/Output Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R2001 DC561, digital input/output module, 16 configurable inputs/outputs,

More information

MINI MCR-SL-RPS-I-I. Repeater power supply, active. Data sheet. 1 Description

MINI MCR-SL-RPS-I-I. Repeater power supply, active. Data sheet. 1 Description Repeater power supply, active Data sheet 09_en_0 PHOENIX CONTACT 0--0 Description The. mm wide... repeater power supply supplies transmitters in the field and electrically isolates the input signal from

More information

MINI MCR-SL-UI-2I(-SP)(-NC)

MINI MCR-SL-UI-2I(-SP)(-NC) Data Sheet 03/2005 Product Description Features Configurable signal duplicator MINI MCR-SL-UI-2I(-SP)(-NC) is used to electrically isolate, condition, amplify, and filter analog standard signals. On the

More information

PROFIBUS-DP/MODBUS RTU REPEATER

PROFIBUS-DP/MODBUS RTU REPEATER RP303 PROFIBUS-DP/MODBUS RTU REPEATER USER S MANUAL JAN/15 RP303 R P 3 0 3 M E smar www.smar.com Specifications and information are subject to change without notice. Up-to-date address information is available

More information

MINI MCR-SL-PT100-UI. Active resistance thermometer measuring transducer. Data sheet. 1 Description

MINI MCR-SL-PT100-UI. Active resistance thermometer measuring transducer. Data sheet. 1 Description Active resistance thermometer measuring transducer Data sheet 099_en_06 PHOENIX CONTACT 0-0- Description The 6. mm wide MINI MCR-SL-PT00-UI-... is a configurable, -way isolated temperature measuring transducer.

More information

RTU500 series Data Sheet Power Supply CP-E 24/2.5

RTU500 series Data Sheet Power Supply CP-E 24/2.5 Data Sheet Power Supply CP-E 24/2.5 Power Supply CP-E 24/2.5 Application The primary switch mode power supply offers two voltage input ranges. This enables the supply with AC or DC. Furthermore it is equipped

More information

IPM-S500 Series MID SINGLE PHASE AND THREE-PHASE ENERGY COUNTERS

IPM-S500 Series MID SINGLE PHASE AND THREE-PHASE ENERGY COUNTERS IPM-S500 Series MID SINGLE PHASE AND THREE-PHASE ENERGY COUNTERS The IPM-500 Series s for DIN rail mounting cover the most different application requirements for single-phase and threephase systems. Available

More information

MODEL: R2K-1 SEN TRONIC AG. R2K Series

MODEL: R2K-1 SEN TRONIC AG. R2K Series 1 MODEL: R2K-1 R2K Series /RS-485 CONVERTER Functions & Features Bidirectional converter between and RS-485 used when connecting Modbus RS-485 devices to a PC CE marking Standard: Conforms to, EIA Transmission

More information

Temperature controller Ducted systems

Temperature controller Ducted systems 2 725 Temperature controller Ducted systems Standard model without zoning functions RRV851 Multifunctional controller used for central control of ducted HVAC systems in combination with a QAX850 master

More information

IMC-21A Quick Installation Guide

IMC-21A Quick Installation Guide IMC-21A Quick Installation Guide Moxa Industrial Media Converter Edition 5.0, February 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

ADA User manual ADA RS-485 / RS-422 to RS-232 Converter. 1 io_ada-4010_v3.22_en. Copyright CEL-MAR sp.j.

ADA User manual ADA RS-485 / RS-422 to RS-232 Converter. 1 io_ada-4010_v3.22_en. Copyright CEL-MAR sp.j. User manual ADA-4010 RS-485 / RS-422 to RS-232 Converter Copyright 2001-2017 CEL-MAR spj 1 io_ada-4010_v322_en Contents 1 GENERAL INFORMATION 3 11 WARRANTED INFORMATION 3 12 GENERAL CONDITIONS FOR SAFE

More information

Gateway BACnet IP/MS-TP slave KNX TP Code: EK-BJ1-TP-IP / EK-BJ1-TP-MSTP

Gateway BACnet IP/MS-TP slave KNX TP Code: EK-BJ1-TP-IP / EK-BJ1-TP-MSTP writing single and multiple -bit registers (Coil and Status) as well as 6-bit registers (Holding and Input). It is also possible to read and write multiple registers containing -bit floating point values

More information

IMC-21GA Quick Installation Guide

IMC-21GA Quick Installation Guide IMC-21GA Quick Installation Guide Moxa Industrial Media Converter Edition 4.0, June 2017 Technical Support Contact Information www.moxa.com/support Moxa Americas: Toll-free: 1-888-669-2872 Tel: 1-714-528-6777

More information

Media Converters. Media Converters. Product Selection Guides

Media Converters. Media Converters. Product Selection Guides Product Selection Guides Media Converters Serial-to-Fiber Converter Selection Guide....................................-2 Serial-to-Serial Converter Selection Guide...................................-3

More information

Rhino Buffer Module PSM24-BFM600S. Operating Instructions

Rhino Buffer Module PSM24-BFM600S. Operating Instructions Rhino Buffer Module PSM24-BFM600S Operating Instructions RHINO BUFFER MODULE PSM24-BFM600S Description The PSM24-BFM600S Buffer Module will hold the output voltage of a 24 VDC power supply after brownouts

More information

10/100Base-TX Industrial Ethernet Extender

10/100Base-TX Industrial Ethernet Extender Quick Start Guide This quick start guide describes how to install and use the Ethernet Extender. The Ethernet Extender introduced here provides one channel for Ethernet over existing voice grade copper

More information

Nemo SX - Multifunction control module

Nemo SX - Multifunction control module Via Travaglia 7, 20094 Corsico (MI) - Italia Tel. +39 0244878.1 - Fax +39 024503448 Contents Pages 1. Description - Use... 1 2. Range... 1 3. Overall dimensions... 1 4. Preparation - Connection... 1 5.

More information

10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter. AMG9011G-H (-40 to 75C) User Manual

10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter. AMG9011G-H (-40 to 75C) User Manual 10/100/1000T to Mini-GBIC Industrial Switch Converter 10/100/1000T to 1000SX/LX Industrial Switch Converter AMG9011G-H (-40 to 75C) User Manual www.amgsystems.com Content Overview...1 Introduction... 1

More information

H704-42(H)(E), H704-42/1(H)(E)

H704-42(H)(E), H704-42/1(H)(E) POWER MONITORING INSTALLATION GUIDE H704-42(H)(E), H704-42/1(H)(E) Branch Current Monitor DANGER NOTICE Installer's Specifications General: Operating Temp. Range 0 to 60 C (32 to 140 F) (

More information

MXIO. Compact I/O module. Summary. Application Compact I/O module for data acquisition and HVAC control systems. Function

MXIO. Compact I/O module. Summary. Application Compact I/O module for data acquisition and HVAC control systems. Function MXIO Compact I/O module Summary The MXIO multiple I/O compact module is a microprocessor-controlled, communicative module with the I/O mix optimized for larger HVAC control applications. The module uses

More information