SYSTEM MAINTENANCE MANUAL TACTICAL ENGAGEMENT SIMULATION SYSTEM (TESS) TARGET TRAINING SYSTEM (TTS) OCONUS FIXED LOCATION INSTALLATION
|
|
- Lora Mosley
- 5 years ago
- Views:
Transcription
1 SYSTEM MAINTENANCE MANUAL TACTICAL ENGAGEMENT SIMULATION SYSTEM (TESS) TARGET TRAINING SYSTEM (TTS) OCONUS FIXED LOCATION INSTALLATION INITIAL SETUP Preconditions Coordinate the TTS setup with the training exercise planners to ensure the TTS is configured with the correct Player Identification (PID) and player type. And the correct setup location is identified. Service upon receipt completed (WP 0006) IPU, WLS, and IPS batteries fully charged (WP 0009) Personnel Required 1 Person Tools Required Screwdriver, cross-tip, No. 2 (WP 0029 figure 3 item 3) Wrench, open End, 7/16 (WP 0029 figure 3 item 4) Hex Key, 3/16, 9-1/4 Blade Length (WP 0029 figure 3 item 11) Equipment Required Target Training System (TTS) kit OCONUS Antenna kit Consumables Required Velcro self-adhesive strip - AR PROCEDURES WARNING If you do the OCONUS TTS fixed location installation in extreme temperature and/or high humidity, make sure you have appropriate clothing, shade, and hydrating fluids. Follow local standard operating procedures and guidance when working in extreme conditions
2 0010 SMM Make sure that the IPU battery is fully charged. If BB-390B/U, BA-5590/U, or BA-5390A/U battery is utilized, IPU operation time can be less than 48 hours. Make sure the Instrumentation Power Supply (IPS) batteries are fully charged. Make sure the WLS batteries are fully charged. The WLS batteries may be installed in the WLS already. The WLS is capable of operating on AA disposable and rechargeable 1.5V batteries of different chemistry than the provided AA rechargeable alkaline. If batteries of other chemistry are utilized, the battery must be removed when the WLS is turned off. Instrumentation Player Unit (IPU) Installation If different chemistry batteries are installed in the WLS, identify the WLS with type of battery installed. Use tape and permanent marker. Do not put tape on top part of housing or obstruct indicator light. 1. Open the TTS storage case and remove the IPU, IPU GreenLinks antenna, antenna pole mount, six Wireless Laser Sensors (WLS), and IPU power cable (Figure 1). STORAGE CASE IPU POLE MOUNT WIRELESS LASER SENSORS (X6) IPU GREENLINKS IPU POWER CABLE Figure 1. TTS Storage Case
3 2. Loosen the two screws on the IPU battery door, open the door, and remove the battery (Figure 2). 3. Make sure the battery is fully charged. CAUTION Do not apply power to the IPU before connecting the TM antenna cable to the IPU applicable antenna connection. If the IPU is operated in the telemetry mode without the TM antenna cable attached to the applicable IPU ANT connector, damage to the radio transceiver can occur. Do not force battery onto connector. connector can occur. Damage to battery or 4. Install the IPU battery, align the battery with the IPU connector. Make sure that the battery is fully seated onto connector. 5. Make sure Compact Flash (CF) memory card is installed in the CF memory card slot. CAUTION Do not tighten battery door screws more than 15 in-lb. (1.69 N m). If you tighten the screws too much, damage to the screws or threaded inserts can occur. 6. Close the battery door and tighten the two screws, tighten screws hand-tight. 7. Install the GreenLinks antenna on the IPU, tighten antenna hand tight. GREENLINKS BATTERY DOOR SCREWS (X2) CF MEMORY CARD BATTERY Figure 2. IPU
4 0010 SMM The IPU should be placed in any location where it can be easily seen from the surrounding area. The IPU can be placed on top of the TTS storage case, if no other suitable location exists. 8. Place the TTS case in an open and visible location (Figure 3). IPU TTS CASE Figure 3. IPU and TTS Case. 9. Connect the IPU to power supply cable to the IPU POWER J4 connector (Figure 4). POWER J4 Figure 4. IPU Power Connection. 10. Connect the opposite end of the IPU to power supply panel cable to the TTS case external connector panel 28 VDC OUT connector (Figure 5)
5 28 VDC OUT CONNECTOR Figure 5. TTS Case External Connections. 11. Slide the antenna pole mount into the mounting bracket on the side of the TTS storage case (Figure 6). POLE MOUNT MOUNTING BRACKET END OF TASK Figure 6. Antenna Pole Mount Mounting Bracket. OCONUS TTS Telemetry Antenna Installation CAUTION Do not apply power to the IPU before connecting the TM antenna cable to the IPU applicable antenna connection. If the IPU is operated in the telemetry mode without the TM antenna cable attached to the applicable IPU ANT connector, damage to the radio transceiver can occur. The adapter may already be installed on the ground plane. 1. Remove the ground plane, adapter, OCONUS antenna, Telemetry (TM) OCONUS cable, and modified antenna pole from the antenna storage case
6 0010 SMM Install the OCONUS antenna onto the ground plane as follows (Figure 7): CAUTION The antenna nut should be only hand tightened to prevent damage to the antenna filament. If the adapter is already installed on the ground plane skip steps 2.a thru 2.e. a. Unscrew the adapter nut from the adapter and remove the nut and flat washer from the adapter. b. Insert the adapter threaded end through the ground plane. c. Install the flat washer and adapter nut onto the adapter. d. Hand-tighten the adapter nut. e. Make sure the O-ring is on the adapter. f. Install the antenna on the adapter, tighten base hand tight only. CLAMP COLLAR FLAT WASHER ADAPTER NUT ADAPTER O-RING BASE ( MHZ) GROUND PLANE Figure 7. OCONUS Antenna ( MHz) Assembly. 3. Slide the TM OCONUS cable connector through the modified antenna pole slot and out of the end of the pole approximately 6 inches. (Figure 8). CABLE Figure 8. Cable Installation. 4. Attach the TM OCONUS cable to the adapter (Figure 9). POLE
7 COLLAR GROUND PLANE CABLE UHF MODIFIED POLE ADAPTER Figure 9. Antenna Cable Connection. 5. Place the ground plane collar on the top of the modified antenna pole (Figure 10). 6. Tighten the ground plane collar screw to clamp and hold the antenna assembly onto the modified antenna pole. Use the T-handle hex wrench supplied with the antenna kit. GROUND PLANE MODIFIED POLE T-HANDLE HEX WRENCH. COLLAR 7. Remove the pole from the antenna case. Figure 10. Antenna and Ground Plane Installation. 8. Slide the pole down through the top bracket and onto the lower bracket (Figure 11)
8 0010 SMM POLE TTS CASE UPPER BRACKET LOWER BRACKET Figure 11. TTS Antenna Installation. 9. Place the antenna and modified antenna pole assembly onto the top of the pole (Figure 12). 10. Place the antenna and modified pole assembly onto the top of the pole placed in the antenna mast holder. 11. Place the IPU near the antenna. Figure 12. OCONUS TTS. 12. Connect the TM OCONUS cable to the MHz connector on the IPU (Figure 13)
9 PROCEDURES CONTINUED MHZ CONNECTOR END OF TASK WLS Installation Figure 13. IPU MHz Antenna Connection. The WLS batteries may be installed in the WLS already. If the batteries are already installed, skip steps 1.a. thru 1.d. 1. If necessary, install the battery in the WLS as follows(figure 14): a. Loosen the two captive screws securing the battery cover to the WLS, remove battery cover. b. Install the AA battery in the WLS. c. Install the battery cover and tighten the two captive screws. d. Repeat steps 1.a. thru 1.c. for all six WLS. BATTERY COVER SCREWS (X2) BATTERY COVER WLS (X6) AA BATTERY Figure 14. WLS. 2. Place the six WLS around the TTS, within 10 meters, to provide 360 degree coverage (Figure 12). END OF TASK END OF WORK PACKAGE /(10 blank)
FLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N
FLOE WIRELESS REMOTE ASSEMBLY INSTRUCTIONS KIT P/N 5-0083-00 TOOLS REQUIRED - 3/4" SOCKET - 3/4" WRENCH - /3" WRENCH - PHILLIPS SCREW DRIVER - TORQUE WRENCH INSTRUCTION P/N 6-0083-00 ISSUED: 3//7 SHEET
More informationSmart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction
Smart Multivariable Transmitter (SMV 3000) Electronics Module Replacement Kit Instruction Electronics Module (Part number 51404208 503, -513) Document Form: 34-SM-33-01 Effective: 09-01 Supersedes: 34-SM-33-01,
More informationInstallation Guide Philips MP60/70 IntelliVue VHM Arm Rail Mount Kit
Installation Guide Philips MP60/70 IntelliVue VHM Arm Rail Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter (page 2) 2. Describe attachment of Down
More informationInstallation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit
Installation Guide Philips MP20/30/40/50/60/70 IntelliVue M-Series Arm Rail Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter on Arm (page 2). 2.
More informationDelta Unifence Kit Installation Instructions
Delta Unifence Kit Installation Instructions Please note this installation kit is designed for installation on the Delta Commercial Unifence (units made between 1993 and current). Accurate Technology manufactures
More informationReplacing the Power Supply
APPENDIX B This appendix includes information on how to replace the power supply for the Cisco AS550XM universal gateway and contains the following sections: Safety Recommendations, page B-1 Required Tools
More informationRaven Adapter Harness
Note: Indented items indicate parts included in an assembly listed above Quantity by System Part Name/Description Part Number With Switch Box With Built-in Switches Raven Harness Adapter Kit 4100504 1
More informationE2460GS Oscilloscope Upgrade Kit
Installation Instructions for E2460GS Oscilloscope Upgrade Kit Agilent 1670G-Series Logic Analyzers This kit upgrades either the Agilent Technologies 1670G, Agilent 1671G, Agilent 1672G, or the Agilent
More informationUniversal Tablet Mount Accessory for Flex TechBridge
Assembly Instructions Universal Tablet Mount Accessory for Flex TechBridge Universal Tablet Mount Accessory Universal Tablet Mount Accessory mounted on Flex Arm CONTENTS Important User Information...........................2
More informationSeries 3700 Screw Terminal Assemblies Installation Instructions
Keithley Instruments, Inc. 28775 Aurora Road Cleveland, Ohio 44139 1-888-KEITHLEY www.keithley.com Series 3700 Screw Terminal Assemblies Installation Instructions Introduction This document contains handling
More informationEVOLVE1-M MONITOR ARM
EVOLVE1-M MONITOR ARM EVOLVE1-M Rev A 2/17 Model EVOLVE1-M-SLV Model EVOLVE1-M-BLK Model EVOLVE1-M-WHT ASSEMBLY AND ADJUSTMENT EVOLVE1-M MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before
More informationTo connect the AC adapter:
Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator
More informationEpson SureColor F6070 Setup Guide
Epson SureColor F6070 Setup Guide 2 Unpacking and Assembling the Printer Read all of these instructions before using your printer. Also be sure to follow all warnings and instructions marked on the printer
More informationRemoval and Installation8
8 Screw Types 8-4 Top Cover Assembly 8-5 Left Hand Cover 8-6 Right Hand Cover 8-10 Front Panel Assembly 8-14 Left Rear Cover 8-15 Right Rear Cover 8-16 Extension Cover (60" Model only) 8-17 Media Lever
More informationInstallation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate
Installation Guide Mounting Kit for Mounting Philips Avalon CTS Cordless Fetal Transducer System on Wall, 2'' Post, Rail, or Slide-on Mounting Plate The purpose of this guide is to: 1. Describe mounting
More informationINSTRUCTION BULLETIN
INSTRUCTION BULLETIN No. 9008755 Machine: T16 Published: 03-2011 Rev. 00 NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts List in the appropriate place in the machine
More informationInstallation Guide. Retrofit Kit for USB Ready Intraoral Systems
Installation Guide Retrofit Kit for USB Ready Intraoral Systems Table of Contents Wall-Mount Retrofit Kit... 2 Introduction... 2 Connecting the Articulating and Horizontal Arm Cables... 2 Installing the
More informationZ Series and S4M Ribbon Take-Up Spindle Maintenance Kit
Z Series and SM Installation Instructions This kit includes the parts and documentation necessary to install the Ribbon Take-Up Spindle Maintenance Kit into the following printers: Z Series (ZM, Z6M, ZMplus,
More informationInstalling the A4504A PMC Bridge Adapter and A4509A Expansion Adapter. HP Part No. A Edition E1197 Printed in U.S.A.
Installing the A4504A PMC Bridge Adapter and A4509A Expansion Adapter HP Part No. A4504-90601 Edition E1197 Printed in U.S.A. Hewlett-Packard Co. 1997 Printing History First Printing: November 1997 UNIX
More informationIBM. Rack Installation Instructions
IBM Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following:
More informationTABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION
S6 USER S MANUAL TABLE OF CONTENTS SECTION 1 TABLETOP CONFIGURATION SECTION 2 TABLETOP CONFIGURATION ACCESSORIES SECTION 3 SLIDE CONFIGURATION SECTION 4 SLIDE CONFIGURATION ACCESSORIES SECTION 5 RACK MOUNT
More informationCutter Option Installation Instructions
This kit includes the parts and documentation necessary to install the cutter option on the Zebra XiII, XiIII, and XiIIIPlus-Series printers. NOTE: The Cutter Option is not available for the 96XiIII. Adding
More informationInstalling the A4979A PMC Graphics Card. HP Part No. A Edition E1098 Printed in U.S.A.
Installing the A4979A PMC Graphics Card HP Part No. A4979-90602 Edition E1098 Printed in U.S.A. Hewlett-Packard Co. 1998 Printing History First Printing: July 1998 Latest Printing: October 1998 UNIX is
More informationValidator Update Instructions for Rowe BC1200 $1 - $20
Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit
More informationV5420 Host Card Upgrade Kit for R3082D Quick Start Guide
Quick Start Guide Upgrade kit contents The table below shows the contents of the V5420 Host Card Upgrade Kit (components are not shown to scale). Part Function Pieces V5420 Host Card 1 Host card bracket
More informationQuick Start Guide. Preparation. Installation. Operation. Support. Vaisala NOMAD 3 Data Logger. Online manuals
Quick Start Guide www.vaisala.com Vaisala NOMAD 3 Data Logger Preparation Package Contents Plan Instrumentation Create a SkyServe Account Activating the Nomad 3 Nomad 3 Toolbox Create Setup Files 2 4 5
More informationRack Installation Instructions
Rack Installation Instructions Review the documentation that comes with your rack cabinet for safety and cabling information. When installing your server in a rack cabinet, consider the following: v Two
More information*520886* IntelliTouch Pool & Spa Control System MobileTouch Wireless Controller. User s and Installation Guide. P/N Rev A
pool/spa control system IntelliTouch Pool & Spa Control System MobileTouch Wireless Controller User s and Installation Guide P/N 520886 - Rev A *520886* i MobileTouch Wireless Controller kit contents The
More informationA-100G6 - Basic frame assembly diagram
doepfer System A - 100 Rack system A-100 G A-100G6 - Basic frame assembly diagram Parts: 1 Rail with lip, and with tapped hole strip inserted (with M3 threads). 2 Rail with lip, with three M3 hexagon nuts
More informationTOYOTA YARIS H/B PREMIUM AUDIO Preparation
Preparation Part Number: PT296-47141 (Extension Box) Kit Contents Item # Quantity Reqd. Description 1 1 Extension Module w/bt cable 2 1 Wire harness 3 4 Screws (M5x8) Hardware Bag Contents Item # Quantity
More informationMk II 3DR MULTI-LINE LASER INSTRUCTION MANUAL
Mk II 3DR MULTI-LINE LASER INSTRUCTION MANUAL SAFETY Read the following safety instructions before attempting to operate this product. Keep these instructions in a safe place or store in the carry case
More informationGeneral Applicability All Scion xb models, including 10 Year Anniversary Edition.
Preparation Part Number: PT296-00140, PT296-00142 or PT296-00151 (Extension Box w/aha) Kit Contents Item # Quantity Req. Description 1 1 Extension Module w/bt cable 2 1 DA/Ext Harness 3 1 GPS Antenna kit
More informationCanon EOS Rebel T2i Top Cover Replacement
Canon EOS Rebel T2i Top Cover Replacement Replacing the top piece of a Canon T2i (550D). In my case, I had a broken hot-shoe, but as most controls on this camera are built into the same part, this repair
More informationDelta Unifence Kit Installation Instructions
Delta Unifence Kit Installation Instructions Please note this installation kit is designed for installation on the Delta Commercial Unifence (units made between 1993 and current). Accurate Technology manufactures
More informationCisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2. Cisco CRS 3-Phase AC Power Distribution Unit 2
Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide Cisco CRS 3-Phase AC Power Distribution Unit Installation Guide 2 Cisco CRS 3-Phase AC Power Distribution Unit 2 Revised: November 18, 2016,
More informationInstalling the Cisco 2524 and Cisco 2525 Routers
CHAPTER 3 Installing the Cisco 2524 and Cisco 2525 Routers This chapter guides you through the installation of the Cisco 2524 and Cisco 2525 routers and includes the following sections: Required Tools
More informationDST550 Digi-Stem Thermometer
DST550 Digi-Stem Thermometer User Manual 09/16/09 WD1045 Rev C Wahl Instruments, Inc. 234 Old Weaverville Road Asheville, NC 28804 Toll Free 800-421-2853 Phone 828-658-3131 Fax 828-658-0728 www.palmerwahl.com
More informationDell Inspiron XPS and Inspiron 9100 Service Manual
Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card
More informationG12/G12x USER S MANUAL
G12/G12x USER S MANUAL TABLE OF CONTENTS SECTION 1 SLIDE CONFIGURATION SECTION 2 SLIDE CONFIGURATION ACCESSORIES SECTION 3 TABLETOP CONFIGURATION SECTION 4 TABLETOP CONFIGURATION ACCESSORIES SECTION 5
More informationTactical Weather Station Set-Up Guide 1
Tactical Weather Station Set-Up Guide 1 This is a generic overview of a portable WEATHERPAK 3 meter tripod set-up. Your system may not include all of the components listed, or may have different components.
More informationH3C S12500 Routing Switch Series
H3C S12500 Routing Switch Series Quick Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: APW201-20131030 Copyright 2013, Hangzhou H3C Technologies Co., Ltd. and
More informationDC Outdoor Power Supply/Chargers
DC Outdoor Power Supply/Chargers Installation Guide Models Include: WayPoint3 WayPoint7-2.5A @ 12VDC or 24VDC. - 6A @ 12VDC or 24VDC. - 115/230VAC input. - 115VAC input. WayPoint5 WayPoint7V - 4A @ 12VDC
More informationRemoval and Installation 8
Removal and Installation 8 8 Introduction 8-2 Service Calibration Guide to Removal and Installation 8-4 Window 8-8 Covers and Trims 8-12 Rear Tray 8-31 Rear Cover 8-32 Media Lever 8-33 Media Lever Position
More informationShop Fox Fence Kit Installation Instructions:
Shop Fox Fence Kit Installation Instructions: Please note this installation kit is designed solely for installation on a Shop Fox Classic Fence. Accurate Technology manufactures kits for other saw fences
More informationInstalling the Interface Line Card in the Cisco cbr Chassis 6
Installing the Interface Line and PIC Cards in the Cisco cbr Chassis Installing the Interface Line and PIC Cards 2 Installing PICs in the Cisco cbr Chassis 2 Installing the Interface Line Card in the Cisco
More informationArticulating TV/Monitor Clamp/Grommet Desk Mount Model: DE640S (Hydro Series)
Articulating TV/Monitor Clamp/Grommet Desk Mount Model: DE640S (Hydro Series) Instruction Manual Images may be different from actual product Disclaimer It is Dyconn s intention to have all the correct
More informationInstalling and Removing SDRAM and DRAM
CHAPTER 4 This chapter explains how to remove and replace the main memory modules on the network processing engine or network services engine. For the location of the memory module you are replacing, find
More informationPeel/Rewind Upgrade Kit
Peel/Rewind Upgrade Kit Installation Instructions This kit includes the parts and documentation necessary to install the Peel/Rewind upgrade kit on the following printers: ZM400 ZM600 Read these instructions
More informationAirLink GX Series X-Card Installation Guide
This installation is to be performed only by certified Sierra Wireless AirLink distributors. If it is performed by anyone other than the certified AirLink distributor, the terms of the warranty agreement
More information2U STORAGE ENCLOSURE QUICK INSTALL GUIDE FS4100, FS4500, SC4100, AND FC4100
2U STORAGE ENCLOSURE QUICK INSTALL GUIDE FS4100, FS4500, SC4100, AND FC4100 Kit Contents Adaptec Storage Enclosure (FS4100, FS4500, SC4100, or FC4100) CD, including software, drivers, and documentation
More informationInstallation Note. Source Attenuators and Bias Tees Upgrade Kit. For E8362B/C PNA Series Microwave Network Analyzers. Network Analyzer Model Number
Installation Note Source Attenuators and Bias Tees Upgrade Kit For E8362B/C PNA Series Microwave Network Analyzers Network Analyzer Model Number Upgrade Kit Part Number E8362B/C E8362-60115 Agilent Part
More informationCLIMB2 DUAL MONITOR SIT/STAND WORKSTATION
CLIMB2 DUAL MONITOR SIT/STAND WORKSTATION CLIMB2 Rev A 3/17 Model CLIMB2-SLV ASSEMBLY AND ADJUSTMENT CLIMB2 PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and adjustment
More informationRemoving and Replacing Parts
Removing and Replacing Parts Preparing to Work Inside the Computer Recommended Tools Screw Identification System Components Hard Drive Fixed Optical Drive Media Bay Devices Memory Modules Mini PCI Card
More informationNavigator II INstallatIoN MaNUal For static and PaN/tIlt configurations
Navigator II Installation MANUAL For Static and Pan/Tilt Configurations Document Number: 432-0001-00-12, rev 100 FLIR Systems, Inc., 2008. All rights reserved worldwide. No parts of this manual, in whole
More informationDIGITAL Server Rackmount Installation Guide
DIGITAL Server Rackmount Installation Guide Part Number: ER-PCSRA-IA. E01 Digital Equipment Corporation December 1997 The information in this document is subject to change without notice and should not
More informationInstallation and Maintenance
CHAPTER 4 Installation and Maintenance Revised: April 19, 2010, Introduction This chapter explains how to install a SCE 1000 platform in a rack or in a general tabletop or workbench installation. Additionally,
More informationxtablet T1600 Vehicle Holder Installation Guide
This document will step you through setting up the T1600 Vehicle Holder installation and tips for a safe, clean and long lasting installation. Preparing to Mount the Vehicle Holder Warning : Dock mounting
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationAlphaGateway SMG-01PE Quick Start Guide
AlphaGateway SMG-01PE Quick Start Guide 9 Power-Passing Tap 2 AlphaGateway SMG 5 1 8 6 3 4 7 PoE Devices Security Camera Wi-Fi Radio 1. 1 RF Connector Test Port A -20dB test port allowing measurement of
More informationedrive RAM Battery Alternate Replacement Procedure
edrive RAM Battery Summary This technical note describes the process for replacing the TINI RAM battery with a higher capacity battery. With the edrive turned on, the external battery can be changed without
More informationCycles Integrated LCD Screen Option. Cardio Theater Integrated Bracket Assembly Instructions
Recumbent Upright Cycles Integrated LCD Screen Option Cardio Theater Integrated Bracket Assembly Instructions Table of Contents 1 2 3 4 5 6 7 Before You Begin... 4 Obtaining Service... 4 Unpacking the
More informationBiesemeyer Fence Kit Installation Instructions:
Biesemeyer Fence Kit Installation Instructions: Please note this installation kit is designed solely for installation on a Biesemeyer Commercial Fence. Accurate Technology manufactures kits for other saw
More informationA-dec 584 Monitor Mount on a Central Cabinet
Installation Guide A-dec 584 Monitor Mount on a Central Cabinet Before You Begin This procedure applies to the A-dec Inspire TM 592 Central Console and the standard and tall Preference cabinet central
More informationHP UPS R/T3000 G2. Overview. Precautions. Kit contents. Installation Instructions
HP UPS R/T3000 G2 Installation Instructions Overview The HP UPS R/T3000 G2 features a 2U rack-mount with convertible tower design and offers power protection for loads up to a maximum of 3300 VA/3000 W
More informationThis chapter shows you how to install a 100G ERT Module on a Sensus meter. The following items are required to install Itron's 100G ERT Module.
C HAPTER 3 Sensus Meter Installation This chapter shows you how to install a 100G ERT Module on a Sensus meter. Sensus meters are also known by the following names: Invensys, Equimeter, and Rockwell. For
More informationWritten By: Teren Wallace
In this guide, we will be showing you how to remove and replace the Touch Pad. Written By: Teren Wallace ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION In this guide, we will be showing you
More informationInstallation Job Aid for VSP 4450GTX-HT- PWR+
Installation Job Aid for VSP 4450GTX-HT- PWR+ Notices Release 6.1.0.0 NN46251-305 Issue 02.01 November 2017 Notice paragraphs alert you about issues that require your attention. The following paragraphs
More informationPracticeWire. Field Support: Page 1
PracticeWire Field Support: 1-877-233-9114 Page 1 Table of Contents Required Tools Page 3 Software Hardware 1) Admin Login.... Page 3 2) Checking AT&T signal strength Page 3 3) Port test.. Page 4 1) Cradlepoint
More informationCHAPTER 5 UNIT MAINTENANCE INSTRUCTIONS
FPU SYSTEMS OPERATION MANUAL (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) STANDARD AND SPECIALIZED FPU MODULES BOH FPU Field Pack-up Units CHAPTER 5 UNIT MAINTENANCE INSTRUCTIONS BOH-PM-0-5 06 BOH Environmental
More informationIntelliLED TM. Controls: User Guide. Picture for DALI only. Wireless adds external antenna. NOTE: These parts are NOT user serviceable
IntelliLED TM Controls: User Guide Picture for DALI only. Wireless adds external antenna. NOTE: These parts are NOT user serviceable www.dialight.com 9100127299899_D April 2018 Table of Contents Introduction
More informationInstallation Job Aid for VSP 4850GTS
Installation Job Aid for VSP 4850GTS Notices Release 6.1.0.0 NN46251-308 Issue 02.01 November 2017 Notice paragraphs alert you about issues that require your attention. The following paragraphs describe
More informationHumidity + Temperature + Pressure Datalogger
User's Guide Humidity + Temperature + Pressure Datalogger Model RHT50 Introduction Congratulations on your purchase of the Relative Humidity / Temperature / Pressure Datalogger. This datalogger can measure
More informationDell Inspiron N5110 Service Manual
Dell Inspiron N5110 Service Manual Regulatory model: P17F Regulatory type: P17F001 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.
More informationCAMERA ASSEMBLY. Removal/Replacement of the Camera Box Assembly APR-CA. Install Camera Assembly. Remove Camera Assembly
CAMERA ASSEMBLY Removal/Replacement of the Camera Box Assembly APR-CA REQUIRED TOOLS: 9/64 hex key Small flat-tip screwdriver Remove Camera Assembly camera 1. Locate the camera assembly underneath the
More informationTRC-190 User s Manual
User s Manual Edition 3.2, May 2017 www.moxa.com/product 2017 Moxa Inc. All rights reserved. User s Manual The software described in this manual is furnished under a license agreement and may be used only
More informationTASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS
TASER Axon Dock Installation Manual IMPORTANT SAFETY INSTRUCTIONS Read all warnings and instructions. Save these instructions. The most up-to-date warnings and instructions are available at www.taser.com
More informationIBM Systems. Quick start guide for IBM System p5 505 ( )
IBM Systems Quick start guide for IBM System p5 505 (9115-505) 1 Before you begin This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly unpack and set up
More informationDell XPS L702X Service Manual
Dell XPS L702X Service Manual Regulatory model: P09E series Regulatory type: P09E002 Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer.
More informationGCX Mounting Assembly Installation Guide. Pedestal Mount for Philips IntelliVue MP5/20/30/40/50/60/70, MX400/450/500/550/600/700/800
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com GCX Mounting Assembly Installation Guide Pedestal Mount for Philips IntelliVue MP5/20/30/40/50/60/70, MX400/450/500/550/600/700/800
More informationInstallation Instructions
Second Kit for the GrandSTAR Jukebox Kit #26694913 Purpose: These instructions outline the procedures to install a second 1000W into the GrandSTAR jukebox with the AV controller (shown) or the 4 Channel
More information2T-RMSMC System Management Station Kit Installation Guide
2T-RMSMC System Management Station Kit Guide Order Number: EK RMSMC IN. A01 Digital Equipment Corporation Maynard, Massachusetts March 1996 Digital Equipment Corporation makes no representations that the
More informationDIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL
DIGITAL OBSERVATION GUARD LOW PROFILE PAN TILT KIT USER MANUAL Version 2.1 June 4, 2013 0 Table of Contents Low Profile Pan Tilt Kit Description... 3 Low Profile Pan Tilt Unit Basic Operation... 4 Mounting
More informationMac Mini Mid 2011 SSD Dual Drive Installation
Mac Mini Mid 2011 SSD Dual Drive Installation Install a second hard drive in your mid 2011 Mac Mini. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 19 INTRODUCTION Use this guide to install
More informationUpgrade Instructions. P/N Revision A. October Printer Terminal Holder * *
Upgrade Instructions P/N 96-08-0 Revision A October 000 480 Printer Terminal Holder P/N 96-08-0 Revision A *96080* Instructions This terminal holder connects the INTERMEC R 600 Series and 700 Series Computers
More informationQuick Start. This document describes how to install the Juniper Networks PTX5000 Packet Transport
PTX5000 Packet Transport Router Quick Start September 2017 Part Number: 530-066788 Revision 01 This document describes how to install the Juniper Networks PTX5000 Packet Transport Router. Contents Quick
More informationMac Mini Mid 2011 SSD Installation
Mac Mini Mid 2011 SSD Installation Replace your Mac Mini Mid 2011's hard drive for more storage space and an increase in speed. Written By: Dozuki System 2017 guides.crucial.com Page 1 of 14 INTRODUCTION
More informationReplacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Backlight Assembly
Replacing the PanelMate Power Pro 1785 Series, PanelMate epro 7585x-8 and 7685x-8 Series Assembly Introduction The Replacement Kit provides a replacement backlight for the PanelMate Power Pro 1785 Series,
More information*E * E E0606
75000 SERIES B Instrument BASIC Installation Note Copyright Agilent Technologies, Inc., 1990-2006 *E1300-90020* E1300-90020 E0606 Manual Part Number: E1300-90020 Printed: June 2006 Edition 1 Rev 2 Microfiche
More informationOracle <Insert Picture Here>
Slide 1 Oracle Slide 2 WZT-6509 version B Sun Fire Nehalem and Westmere Rack-Mount Server Installation and Replacement Welcome to the installation and replacement
More informationACCESSORIES FOR SAFETY DEVICES
ACCESSORIES FOR SAFETY DEVICES - SE-DM: series: deviating mirrors - SE-LP: series: laser pointer - SE-S: series: floor stand - SE-SR2 series: safety relay - SE-SRT series: connection box INSTALLATION SE-DM
More informationTrimble R10 MODEL 2 GNSS SYSTEM. C WARNING For safety information, refer to the Safety Information FIVE SIMPLE STEPS TO GET STARTED
QUICK START GUIDE Trimble R10 MODEL 2 GNSS SYSTEM C WARNING For safety information, refer to the Safety Information section of the Trimble R10 Model 2 GNSS Receiver User Guide. FIVE SIMPLE STEPS TO GET
More informationINSTRUCTIONS FOR THE INSTALLATION OF THE INFINITY "L" DISPLAY HOOD (INTO PREVIOUSLY INSTALLED INFINITY "L" SYSTEMS)
Doc. 6001025 Rev B INSTRUCTIONS FOR THE INSTALLATION OF THE INFINITY "L" DISPLAY HOOD (INTO PREVIOUSLY INSTALLED INFINITY "L" SYSTEMS) Rev. B Doc. 6001025 Page 1 of 13 IMPORTANT NOTICE This document covers
More informationReplace the edrive TINI Module and Battery
Product All edrive Configurations Special Information INFORMATION: This service bulletin is for informational purposes only. It is intended for use by Northrop Grumman Cutting Edge Optronics (NG CEO) employees
More informationQuick Installation Guide
Quick Installation Guide AIRNET 54 Mb CPE Bridge Point to Point Kit Series Package Contents: 2 Netkrom CPE units Two Mounting bracket include: 2 stainless steel U-Bolt, 2 mounting brackets, 2 pipe Brackets
More informationPower Supply, 17-inch
apple imac G5 Power Supply, 17-inch Replacement Instructions Follow the instructions in this sheet carefully. Failure to follow these instructions could damage your equipment and void its warranty. Note:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 19 20 21 01 07 22 23 13 10 12 08 17 18 11 02 14 15 04 03 16 WELCOME PARTS LIST Thank you for purchasing this HealthPoint Technology Cabinet from Humanscale! Before you begin installing
More informationQuick start guide for i5 520 ( or )
Quick start guide for i5 520 (9405-520 or 9406-520) 1 Before you begin This Quick start guide contains an abbreviated set of setup instructions designed to help you quickly unpack and set up a standard
More informationInstallation Instructions for AV/VC One Screen Mount Kit
Installation Instructions for AV/VC One Screen Mount Kit AVS/021/SMK1 REFER ALSO TO MAIN INSTALLATION INSTRUCTIONS FOR AV/VC ONE For dual screen installations you will require 2x AVS/021/SMK1 PARTS INCLUDED:
More informationCommBox Interactive Table User Manual 1.0. Revision: 5
CommBox Interactive Table User Manual 1.0 Revision: 5 Table of Contents 1 Introduction 3 1.1 Table Assembly Components 3 1.2 Accessories 3 2 Table Assembly Procedure 4 2.1 Step 1 4 2.2 Step 2 5 2.3 Step
More informationAsset 4000 Hardware Installation Guide
Asset 4000 v1.0 Installation Guide Page 1 of 11 Asset 4000 Hardware Installation Guide Table of Contents Installation Overview 1 Mounting Location Selection 2 Mounting Hardware 3 Power Up and Down 4 Replacing
More information