ENGLISH version. Safety informations / introduction... page 2. Introduction... page 3. Technical features... page 4

Transcription

1 Safety informations / introduction... page 2 Introduction... page 3 Technical features... page 4 Lamp installation, replacement (halogen)... page 5 ENGLISH version Lamp installation, replacement (discharge)... page 6 Main supply connection... page 7 DMX signal connection /DMX terminal line... page 7 Control panel... page 8 Example of connection DMX controller-spot... page 8 DMX Listing... page 9 Setup and configuration... page 10 1

2 ! WARNING SAFETY INFORMATION READ ALL CAUTIONS AND WARNINGS PRIOR TO OPERATE THIS EQUIPMENT. INSTRUCTION TO PREVENT INJURY OR DAMAGE DUE TO ELECTRIC SHOCK, FIRE, MECHANICAL HAZARDS, UV RADIATION HAZARDS AND DANGEROUS MATTERS. PROTECTION AGAINST DANGEROUS MATTERS At the end of its working life, the product must not be disposed of as urbamn waste. It must be taken to a special local authority differentiate waste collection centre or to a dealer providing this service. The wrong disposal must be cause of environment and people damages in the presence of possible dangerous matters. There are provided for sanctions to a unauthorized disposal of these products. PROTECTION AGAINTS FIRE 1) This equipment is designed for use with the following lamps only: MSD 575, MSR 575/2, HPL 575 halogen. DO NOT USE ANY OTHER TYPE LAMP! 2) Maintain minimum distance of 0.5 meter from walls or any other type flammable surfaces. 3) Maintain minimum distance to lighted objects of 2.0 meters. 4) Replace fuses only with the specified type and rating. 5) Do not install the spot close to heat sources. Do not lay the connection cable on the spot when it is warm. PROTECTION AGAINST ELECTRIC SHOCK 1) This equipment must be earthed. 2) Class I equipment. The power supply cord includes a protective earthing conductor as part of the cord. 3) The equipment must be connected to branch circuit having a circuit- breacker In=6.3A Id=0.03A (230VAC) 4) Disconnect power before lamp s replacement or servicing (service personnel). 2m F PROTECTION AGAINST MECHANICAL HAZARDS 1) Use secondary safety chain when fixing this equipment. 2) Hot lamp explosion hazard. Do not open the equipment for 5 minites after switching off. 3) Equipment surface may reach temperature higher then 130 C. Allow about five minutes before handling. 4) Replace the lamp if it is damaged or thermally deformed. PROTECTION AGAINST UV RADIATION HAZARDS 1) Do not start on this equipment without lamp enclosure or if the protection screens, or ultraviolets screens are damaged. 2) The protection screens, the lenses, or the ultraviolet filters must be replaced if they are visibly damaged and their effectiveness has been reduced, for example, by cracks or deep scratches. 3) Do not look directly at the lamp while lamp is lit-up. 2

3 INTRODUCTION Thank you for choosing the CS1 wash light moving head! The CS1 is a moving head wash light projector: it s equiped with four different lenses for four different beam angles: 15 (very narrow beam), 19 (narrow beam), 21 x34 (medium beam), 30 x51 (wide beam). The CS1 comes in two versions: Art CS1 575 for discharge lamp Art CS1 575 for halogen lamp The input protocol is the DMX 512. To drive the CS1 we suggest to use either our controller Control Show 512,Control Five, Fancy or the Easy Control. To make the most of its possibilites and for a correct functioning of this unit in the years to come, we suggest you to read carefully this manual before connecting or putting the spot into use. By doing so you will gain experience with its commands and connections and you will be easily able to use it. YOUR REFERENCE Always remember to give the serial number and to specify the model any time you address the seller for information or assistance. BASIC KIT The basic kit of the CS1 moving head consist of: Projector Four lenses User s manual Power connector Standard fixing bracket Studio Due warranty Available on request: Lamp art. Clamp: clamp to hang the fixture to any structure and regulate its position art. FL2: kit 2 fast lock art CS1/dimmer: mechanical dimmer (for CS1 dicharge) art CS1/color scroller: color scroller (for CS1 halogen)! WARNING Check that the fixture has not been damaged during transport. If it has been damaged or it does not work, address the seller. Whether the fixture has been shipped to you directly, please contact the shipping company. Only the consignee (person or company) can claim for these damages. 3

4 TECHNICAL FEATURES SOURCE Art : CS1 575W discharge MSD 575 or MSR 575/2 Color temperature: K (MSD575) or K (MSR575) Lamp life: hrs (MSD575) or hrs (MSR575) Luminous flux: lm (MSD575) or lm (MSR575) Color rendering index (Ra): 75 (MSD575) or 80 (MSR575) Art : CS1 575W halogen HPL 575 Color temperature: K Lamp life: 300 hrs Luminous flux: lm OPTIC Equipped with 4 version of lenses for 4 beam angles (50%) 15 with VNSP lens (very narrow beam) 19 with NSP lens (narrow beam) 21 x34 with MFL lens (medium beam) 30 x51 with WFL lens (wide beam) PAN TILT Movement: stepper motor 8 or 16 bit resolution: 540 Pan, 270 Tilt Encoder close loop with autorepositioning ELECTRONIC PROGRESSIVE DIMMER for CS1 575W halogen: electronic dimmer 100%-0% for CS1 575W discharge: electronic dimmer 100%-60% (mechanical 100% - 0% with art. 0501: CS dimmer) CONTROL INPUT Standard interface: RS-485, opto-coupled input Protocol: USITT DMX512 SETTING Built-in microprocessor with display and buttons DMX CHANNELS 1= motor speed 2= aux 3= reset/lamp off 4= dimmer 5= pan coarse 6= pan fine 7= tilt coarse 8= tilt fine POWER SUPPLY Rated voltage: V; 50/60Hz, electronic ballast (for CS1-575 halogen lamp, it is necessary to utilize the lamp code OSRAM: for 117V, for 230V) PHISYCAL dimensions (wxdxh) - weight Art (halogen): mm 400x320x525 - Kg 10 Art (discharge): mm 435x320x525 - Kg 12 4

5 INSTALLATION OF THE HALOGEN LAMP! WARNING In case of replacement of the lamp or maintenance, do not open the fixture unless 5 minutes have passed from the switching off. 1) Disconnect power before the lamp installation or lamp replacement. Wear gloves and goggles. 2) Unscrew the lampholder pawl A on the back of the head fixture. (pict.1) 3) Open the lampholder on the back of head fixture. (pict.2) 4) Insert the lamp into the lampholder socket (pict.3). Do not touch the quarz bulb with fingers. If this happens, clean the bulb before use with cloth and alcohol. Polish with a dry cloth. 5) Close again the lampholder (pict.4) and screw the pawl A. 6) Check if the lampholder box is wedged into the cooling ribs (pict.1) COOLING RIBS LAMPHOLDER BOX LAMPHOLDER BOX PAWL (A) pict.1 LAMP LAMPHOLDER pict.2 pict.3 pict.4 5

6 INSTALLATION OF THE DISCHARGE LAMP! WARNING In case of replacement of the lamp or maintenance, do not open the fixture unless 5 minutes have passed from the switching off. 1) Disconnect power before the lamp installation or lamp replacement. Wear gloves and goggles. 2) Unscrew the lampholder pawl A on the back of the head fixture. (pict.1) 3) Open the lampholder on the back of head fixture. (pict.2) 4) Insert the lamp into the lampholder socket (pict.3). Do not touch the quarz bulb with fingers. If this happens, clean the bulb before use with cloth and alcohol. Polish with a dry cloth. 5) Close again the lampholder (pict.4) and screw the pawl A. 6) Check if the lampholder box is wedged into the cooling ribs (pict.1) PAWL (A) COOLING RIBS LAMPHOLDER BOX pict.1 LAMPHOLDER BOX LAMP LAMPHOLDER pict.2 PAWL (A) pict.3 pict.4 6

7 CONNECTION TO THE MAIN POWER This equipment must be earthed. Class I equipment. The power supply cord includes a protective earthing conductor as part of the cord. MAIN IN Power input L=LIVE (brown) N=NEUTRAL (blue) I =EARTH (green/yellow) Rated voltage Volts / Hz DMX TERMINAL LINE The wrong connection of the terminal line or its non-connection are probably the most frequent reasons for the defective functioning of the DMX line. The terminator is a terminal resistor fitted at the end of the cable furthest from the transmitter. The terminal resistor should have the same value as the impedance of the connection cable. We suggest to use a terminal with a 100 ohm resistor. It is recommanded that all DMX 512 systems have the terminal resistor fitted in the DMX output of the last fixture. PIN WIRE SIGNAL 1 SHIELD GROUND/RETURN/OV 2 INNER CONDUCTOR DATA COMPLEMENT ( -, INVERTED) 3 INNER CONDUCTOR DATA TRUE ( +, NOT INVERTED) 7

8 HALOGEN/DICHARGE FIXTURE CONTROL PANEL On the control panel of the fixture you can find, besides the display, the leds and the buttons to use to set the spot. Sulla base dell apparecchio troverete il pannello dei comandi per il SetUp composto da 4 tasti, un display e 4 led di controllo. LED DMX led flashing: off: LAMP OFF led flashing: off: LAMP DIM led* flashing: off: ERROR led flashing: off: DMX input present / presenza del segnale DMX no DMX input / DMX assente the lamp switching off is remotely controlled / la lampada è spenta dal controllo remoto lamp switched on / la lampada è accesa the lamp dimmered 0/40% off is remotely controlled / la lampada risulta dimmerata dal controllo remoto lamp switched on 100% / la lampada è al 100% SetUp Fixture in mode music synch / è in funzione il modo sincronismo musicale SetUp Fixture in mode Normal os Slave / è in modo Normale o Slave DMX LAMP OFF LAMP DIM BUTTONS ERROR Four buttons are used to programme the spot: DOWN DISPLAY ESC Usare i quattro pulsanti per la programmazione: UP ENTER ESC - exit from menu and return to a previus menu level - esce dal menu e torna ad un livello inferiore DOWN - to go backward in the selected options - scorrimento indietro UP - to go forward in the selected options - scorrimento avanti ENTER - to confirm the selected options - conferma delle opzioni selezionate ERROR UP + DOWN = Fixture reset reset dell apparecchio DISPLAY Shows the various menus and the selected options. Mostra i vari menu e le opzioni selezionate. EXAMPLE OF CONNECTION DMX CONTROLLER-SPOT 8 ERROR

9 DMX LISTING 9

10 SETUP AND CONFIGURATION 10

11 NOTE 11