multiport Floppy Drive User s Manual

Transcription

1 multiprt Flppy Drive User s Manual ISO9001 and AS9100 Certified BDM Rev. A

2 multiprt Flppy Drive RTD EMBEDDED TECHNOLOGIES, INC. 103 Innvatin Blvd State Cllege, PA Phne: FAX: Web Site Page 2 f 11

3 Manual Revisin Histry Rev A Initial Release Published by: RTD Embedded Technlgies, Inc. 103 Innvatin Bulevard State Cllege, PA Cpyright 2005 by RTD Embedded Technlgies, Inc. All rights reserved. The RTD Embedded Technlgies Lg is a registered trademark f RTD Embedded Technlgies. dspmdule, cpumdule, and utilitymdule are trademarks f RTD Embedded Technlgies. PC/104, PC/104-Plus, and PCI-104 are registered trademark f PC/104 Cnsrtium. All ther trademarks appearing in this dcument are the prperty f their respective wners. Page 3 f 11

4 Table f Cntents Intrductin... 5 Prduct Overview... 5 Bard Features... 5 Flppy Drive Features... 5 Physical Attributes... 5 Available Optins... 5 XK-CM IDAN-IFK Getting Technical Supprt... 6 Bard Hardware... 7 Cnnectr and Jumper Lcatins... 7 Jumpers... 7 JP2 Pullup Optins Jumper (Default = 3-4)... 7 External I/O Cnnectins... 8 Drive Pwer In... 8 multiprt Cnnectrs... 8 Drive Pwer Out... 9 Flppy Signals Cnnectr... 9 Bard Installatin Installing the Hardware Static Precautins Steps fr Installing BIOS Cnfiguratin Limited Warranty Page 4 f 11

5 Intrductin Prduct Overview The multiprt Flppy Drive is designed t prvide flppy drive supprt t the RTD line f cpumdules. Selected cpumdules are capable f prviding the flppy drive signals n the parallel prt cnnectr, r multiprt. This flppy drive then attaches t the multiprt. There is n sftware r BIOS emulatin, s the flppy drive appears t the perating system as a standard flppy drive. Bard Features Flppy Drive Features Standard Flppy Drive interface can be used with any perating system Includes Flppy Drive and all required cables. Can be munted in a 3.5 drive bay Physical Attributes Cable Length: 12 inches Size: 6.00 L x 4.00 W x 1.00 H (152mm L x 102mm W x 25mm H) Weight: 1.0 lbs (454 g) Operating Temperature: 4 C t +50 C Strage Temperature: -22 C t +60 C Pwer Requirements: Max: VDC Typical: VDC Available Optins The multiprt Flppy Drive is available in the fllwing cable kits. XK-CM49 Cnfigured fr bare bard applicatins Includes cable t attach t 26-pin, DIL multiprt Includes cable t attach t 26-pin,2mm DIL multiprt Includes pwer cable IDAN-IFK-3 Cnfigured fr IDAN applicatins. Includes cable t attach t DB-25 multiprt Includes pwer cable Page 5 f 11

6 Getting Technical Supprt Fr help with this prduct, r any ther prduct made by RTD, yu can cntact RTD Embedded Technlgies via the fllwing methds: Phne: techsupprt@rtd.cm Be sure t check the RTD web site ( frequently fr prduct updates, including newer versins f the bard manual and applicatin sftware. Page 6 f 11

7 Bard Hardware Cnnectr and Jumper Lcatins The fllwing diagram shws the lcatin f all cnnectrs and jumpers n the multiprt Flppy Drive. Fr a descriptin f each jumper and cnnectr, refer t the fllwing sectins. Cnnectr and Jumper Lcatins Drive Pwer In 2mm multiprt 0.1 multiprt n.c. GND GND +5V Drive Pwer Out (Bttm Side) JP2: Pullup Optins CN15: Flppy Signal (Bttm Side) Jumpers The fllwing sectins describe the jumper cnfiguratin ptins available n the multiprt Flppy Drive. JP2 Pullup Optins Jumper (Default = 3-4) Several f the flppy drive signals require pullup resistr in rder t perate prperly. These pullup resistrs are prvided n the multiprt Flppy Drive bard. They can be pwered either frm the flppy drive pwer cnnectr, r frm the pwer signal n the multiprt. The default cnfiguratin shuld be used fr all applicatins. JP2 Descriptin 1-2 Pullups pwered frm multiprt 3-4 Pullups pwered frm pwer cnnectr (default) Page 7 f 11

8 External I/O Cnnectins The fllwing sectins describe the external I/O cnnectins f the multiprt Flppy Drive. Drive Pwer In This cnnects t a standard flppy drive pwer cnnectr. It supplies pwer t the drive, and can als supply pwer t the n-bard pull-up resistrs. The pin assignments fr the pwer cnnectr are: Nte: Pin 1 can be identified by a square slder pad. Pin Signal Wire Clr 1 +5V Red 2 GND Black 3 GND Black 4 12V(n.c.) Yellw multiprt Cnnectrs Tw cnnectrs are prvided fr the multiprt t accmmdate the full line f cpumdules. One cnnectr has 0.1 pin spacing and the ther has 2mm pin spacing. Only ne cnnectr shuld be used at a time. The pin assignments are the same fr bth, and are as fllws: Nte: Pin 1 can be identified by a square slder pad. Pins 2 10 have rund slder pads. Pin DB25 Functin DR0 3 2 INDEX# 4 15 HDSEL# 5 3 TRK0# 6 16 DIR# 7 4 WRTPRT# 8 17 STEP# 9 5 RDATA# GND 11 6 DSKCHG GND GND GND GND DS1# GND MTR# GND GND WGATE# V Page 8 f 11

9 Drive Pwer Out This cnnectr mates t the pwer cnnectr n the flppy drive. It is a direct cnnectin t the Drive Pwer In cnnectr. Flppy Signals Cnnectr This is a standard 34-pin flppy drive cnnectr. It mates with the signal cnnectr f the flppy drive. All f the signals fr this cnnectr are prvided by the multiprt cnnectr. Page 9 f 11

10 Bard Installatin Installing the Hardware The multiprt Flppy Drive can be attached t any RTD cpumdule that supprts flppy thrugh the multiprt. It can be attached either directly t the cpumdule, r t the multiprt cnnectr n an IDAN frame. Static Precautins Keep yur drive in its antistatic bag until yu are ready t install it int yur system! When remving it frm the bag, hld the drive at the edges and d nt tuch the cmpnents r cnnectrs. Handle the bard in an antistatic envirnment and use a grunded wrkbench fr testing and handling f yur hardware. Steps fr Installing 1. Shut dwn the PC/104 system and unplug the pwer crd. 2. Grund yurself with an anti-static strap. 3. Set the jumpers as described in the previus chapter. 4. Attach the apprpriate cable between the drive and the cpumdule. 5. Bt the system and setup the BIOS as described in the manual fr the cpumdule. 6. Verify that all f the hardware is wrking prperly. BIOS Cnfiguratin After physically installing the drive, the cpumdule BIOS must be cnfigured t use it. The settings that need t be changed depend n the cpumdule used. Check the multiprt: Flppy Cntrller Mde sectin f the cpumdule manual fr the apprpriate setting fr yur cpumdule. Page 10 f 11

11 Limited Warranty RTD Embedded Technlgies, Inc. warrants the hardware and sftware prducts it manufactures and prduces t be free frm defects in materials and wrkmanship fr ne year fllwing the date f shipment frm RTD EMBEDDED TECHNOLOGIES, INC. This warranty is limited t the riginal purchaser f prduct and is nt transferable. During the ne year warranty perid, RTD EMBEDDED TECHNOLOGIES will repair r replace, at its ptin, any defective prducts r parts at n additinal charge, prvided that the prduct is returned, shipping prepaid, t RTD EMBEDDED TECHNOLOGIES. All replaced parts and prducts becme the prperty f RTD EMBEDDED TECHNOLOGIES. Befre returning any prduct fr repair, custmers are required t cntact the factry fr an RMA number. THIS LIMITED WARRANTY DOES NOT EXTEND TO ANY PRODUCTS WHICH HAVE BEEN DAMAGED AS A RESULT OF ACCIDENT, MISUSE, ABUSE (such as: use f incrrect input vltages, imprper r insufficient ventilatin, failure t fllw the perating instructins that are prvided by RTD EMBEDDED TECHNOLOGIES, "acts f Gd" r ther cntingencies beynd the cntrl f RTD EMBEDDED TECHNOLOGIES), OR AS A RESULT OF SERVICE OR MODIFICATION BY ANYONE OTHER THAN RTD EMBEDDED TECHNOLOGIES. EXCEPT AS EXPRESSLY SET FORTH ABOVE, NO OTHER WARRANTIES ARE EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND RTD EMBEDDED TECHNOLOGIES EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED HEREIN. ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES FOR MECHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS WARRANTY. IN THE EVENT THE PRODUCT IS NOT FREE FROM DEFECTS AS WARRANTED ABOVE, THE PURCHASER'S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED ABOVE. UNDER NO CIRCUMSTANCES WILL RTD EMBEDDED TECHNOLOGIES BE LIABLE TO THE PURCHASER OR ANY USER FOR ANY DAMAGES, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, LOST PROFITS, LOST SAVINGS, OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS AND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. Page 11 f 11