MAKING MODERN LIVING POSSIBLE. Quick Guide. VLT HVAC Basic Drive Cascade Control *MG18F102*

Size: px
Start display at page:

Download "MAKING MODERN LIVING POSSIBLE. Quick Guide. VLT HVAC Basic Drive Cascade Control *MG18F102*"

Transcription

1 MAKING MODERN LIVING POSSIBLE Quick Guide VLT HVAC Basic Drive Cascade Control 30R0265 MG8F02 *MG8F02* Rev

2 Contents Contents Quick Guide 2. Safety 2.. Warnings 2..2 Safety Instructions 2.2 Introduction 2.2. Available Literature Approvals IT Mains Avoid Unintended Start Disposal Instruction 3.3 Installation 3.3. Before Starting Repair Work Side-by-Side Installation Mechanical Dimensions Electrical Installation in General Connecting to Mains and Motor Fuses EMC-Correct Electrical Installation Control Terminals Electrical Overview 0.4 Programming.4. Programming with the Local Control Panel (LCP).4.2 The Start-up Wizard for Open Loop Applications 2.5 Cascade Controller 9.5. BASIC Cascade Controller System Status and Operation Start/Stop Conditions Cascade Application Wizard 22.6 Parameter Overview 23.7 Warnings and Alarms 30.8 General Specifications Mains Supply 3 x VAC EMC Test Results 35.9 Special Conditions Derating for Ambient Temperature Derating for Low Air Pressure 38.0 Options for VLT HVAC Basic Drive FC 38 MG.8.F.02 - VLT is a registered Danfoss trademark

3 Quick Guide. Safety.. Warnings WARNING High Voltage Warning The voltage of the frequency converter is dangerous whenever it is connected to mains. Incorrect installation of the motor or frequency converter may cause damage to the equipment, serious injury or death. Consequently, it is essential to comply with the instructions in this manual as well as local and national rules and safety regulations. WARNING Electrical Hazard Touching the electrical parts may be fatal - even after the equipment has been disconnected from mains. Also make sure that other voltage inputs have been disconnected (linkage of DC intermediate circuit). Be aware that there may be high voltage on the DC link even when the LEDs are turned off. Before touching any potentially live parts of the frequency converter, wait at least as stated in the table below: Motor Thermal Protection: Motor overload protection is possible by setting Parameter -90 Motor thermal protection to the value Electronic Thermal Relay (ETR) trip. WARNING Installation at high altitudes For altitudes above 2 km, please contact Danfoss regarding PELV...2 Safety Instructions Make sure the frequency converter is properly connected to earth. Do not remove mains connections, motor connections or other power connections while the frequency converter is connected to power. Protect users against supply voltage. Protect the motor against overloading according to national and local regulations. The earth leakage current exceeds 3.5 ma. The [OFF] key is not a safety switch. It does not disconnect the frequency converter from mains. Voltage (V) Power range (kw) Min. waiting time (min.) 3 x 400 0,37 7,5 4 3 x CAUTION Leakage Current: The earth leakage current from the frequency converter exceeds 3.5 ma. According to IEC a reinforced Protective Earth connection must be ensured by means of a min. 0mm² Cu or an addtional PE wire - with the same cable cross section as the Mains wiring - must be terminated separately. Residual Current Device: This product can cause a DC current in the protective conductor. Where a residual current device (RCD) is used for extra protection, only an RCD of Type B (time delayed) shall be used on the supply side of this product. See also Danfoss Application Note on RCD, MN.90.GX.YY. Protective earthing of the frequency converter and the use of RCDs must always follow national and local regulations..2 Introduction.2. Available Literature This quick guide contains the basic information necessary for installing and running the frequency converter. If more information is needed, literature can be found on the enclosed cd or downloaded from: +Documentation.htm.2.2 Approvals 2 MG.8.F.02 - VLT is a registered Danfoss trademark

4 .2.3 IT Mains CAUTION IT Mains Installation on isolated mains source, i.e. IT mains. Max. supply voltage allowed when connected to mains: 440V (3x V units). On V IP20 0,37-22kW, open the RFI switch by removing the screw on the side of the frequency converter when at IT grid. 30BB Installation.3. Before Starting Repair Work. Disconnect FC from mains (and external DC supply, if present.) 2. Wait as stated in the table below for discharge of the DC-link: Voltage (V) Power range (kw) Min. waiting time (min.) 3 x x Remove motor cable.3.2 Side-by-Side Installation The frequency converter can be mounted side-by-side and requires the clearance above and below for cooling. Illustration. IP20 0,37-22kW V. : EMC screw On all units, set par RFI filter to OFF when operating in IT mains. CAUTION If reinserted, only use M3x2 screw..2.4 Avoid Unintended Start While the frequency converter is connected to mains, the motor can be started/stopped using digital commands, bus commands, references or via the LCP. Disconnect the frequency converter from mains whenever personal safety considerations make it necessary to avoid unintended start of any motors. To avoid unintended start, always activate the [OFF] key before changing parameters. Power Frame IP class 3 x V H IP kW/ 0.5-2Hp H2 IP kW/ 3-5.4Hp H3 IP kw/ Hp H4 IP20-5kW/ 5-20Hp H5 IP kW/ 25-30Hp H6 IP kW/ 40-60Hp H7 IP kW/ 00-20Hp H8 IP20 90kW/ 25Hp Clearance above/ below (mm/inch) 00/4 00/4 00/4 00/4 00/4 200/7,9 200/7,9 225/8,9 NOTE With IP2/Nema Type option kit mounted, a distance of 50mm between the units is required..2.5 Disposal Instruction Equipment containing electrical components must not be disposed of together with domestic waste. It must be separately collected with electrical and electronic waste according to local and currently valid legislation. MG.8.F.02 - VLT is a registered Danfoss trademark 3

5 .3.3 Mechanical Dimensions C B b 0 D 30BB64.0 a A Power Height (mm/inch) Width (mm/inch) Depth (mm/ inch) Hole (mm) Frame IP class 3 x V A A incl. A B b C D Decoupling plate H IP kW/ 95/ /0.7 83/7.2 75/3 56/2.2 68/ Hp H2 IP kW/ 227/ /.9 22/8.3 90/3.5 65/2.6 90/ Hp H3 IP kW/ 255/0 329/3 240/9.4 00/3.9 74/ / Hp H4 IP20-5kW/ 296/.7 359/4. 275/0.8 35/5.3 05/4. 24/ Hp H5 IP kW/ 334/3. 402/5.8 34/2.4 50/5.9 20/ / Hp H6 IP kW/ 58/ / / / / / Hp 635/25 H7 IP kW/ 550/ / / / / / Hp 690/27.2 H8 IP20 90kW/ 20Hp 660/26 800/3.5 63/ / /3 335/ Table. Mechanical Dimensions.3.4 Electrical Installation in General All cabling must comply with national and local regulations on cable cross-sections and ambient temperature. Copper conductors required, (75 C) recommended. Power (kw) Torque (Nm) Frame IP class 3 x Line Motor DC connection Control Earth Relay terminals H IP H2 IP H3 IP H4 IP H5 IP H6 IP H7 IP H7 IP H8 IP H8 IP Cable dimensions 95mm 2 2 Cable dimensions > 95mm 2 4 MG.8.F.02 - VLT is a registered Danfoss trademark

6 .3.5 Connecting to Mains and Motor The frequency converter is designed to operate all standard three-phased asynchronous motors. For maximum cross-section on wires please see section Mains Supply. 30BB634.0 Use a shielded/armored motor cable to comply with EMC emission specifications, and connect this cable to both the decoupling plate and the motor metal. Keep motor cable as short as possible to reduce the noise level and leakage currents. For further details on mounting of the decoupling plate, please see instruction MI. 02.QX.YY Also see EMC-Correct Installation in the Design Guide, MG.8.CX.YY. 2 2 MAINS Motor U V W -DC +DC 4. Mount the earth wires to earth terminal Connect motor to terminals U, V and W. 3. Mount mains supply to terminals L, L2 and L3 and tighten. Illustration.2 IP V kW. Line 2 Earth 3 Motor 4 Relays MG.8.F.02 - VLT is a registered Danfoss trademark 5

7 IP V 30-45kW IP V 90kW 30BB BB L 9 / L2 92 / L3 93 L L L U V w U 96 / V 97 / W Line 2 Motor 3 Earth 4 Relays IP V 55-75kW 30BB763.0 Line 2 Relays 3 Earth 4 Motor.3.6 Fuses Branch circuit protection In order to protect the installation against electrical and fire hazard, all branch circuits in an installation, switch gear, machines etc., must be short-circuit and overcurrent protected according to national/international regulations. Short circuit protection Danfoss recommends using the fuses mentioned in the following tables to protect service personnel or other equipment in case of an internal failure in the unit or short-circuit on DC-link. The frequency converter provides full short circuit protection in case of a short-circuit on the motor Overcurrent protection Provide overload protection to avoid overheating of the cables in the installation. Overcurrent protection must always be carried out according to national regulations. Fuses must be designed for protection in a circuit capable of supplying a maximum of 00,000Arms (symmetrical), 480V maximum. Line 2 Relays 3 Earth 4 Motor 6 MG.8.F.02 - VLT is a registered Danfoss trademark

8 Non UL compliance If UL/cUL is not to be complied with, Danfoss recommends using the fuses mentioned in the below table, which will ensure compliance with IEC : In case of malfunction, not following the fuse recommendation may result in damage to the frequency converter. UL Power kw 3 x V Non UL Bussmann Bussmann Bussmann Bussmann Max. Fuse Type RK5 Type RK Type J Type T Type gg 0.37 FRS-R-0 KTS-R0 JKS-0 JJS FRS-R-0 KTS-R0 JKS-0 JJS FRS-R-0 KTS-R0 JKS-0 JJS FRS-R-5 KTS-R5 JKS-5 JJS FRS-R-5 KTS-R5 JKS-5 JJS FRS-R-5 KTS-R5 JKS-5 JJS FRS-R-25 KTS-R25 JKS-25 JJS FRS-R-25 KTS-R25 JKS-25 JJS FRS-R-50 KTS-R50 JKS-50 JJS FRS-R-50 KTS-R50 JKS-50 JJS FRS-R-80 KTS-R80 JKS-80 JJS FRS-R-80 KTS-R80 JKS-80 JJS FRS-R-80 KTS-R80 JKS-R80 JJS-R FRS-R-00 KTS-R00 JKS-R00 JJS-R FRS-R-25 KTS-R25 JKS-R25 JJS-R FRS-R-50 KTS-R50 JKS-R50 JJS-R FRS-R-200 KTS-R200 JKS-R200 JJS-R FRS-R-250 KTS-R250 JKS-R250 JJS-R EMC-Correct Electrical Installation General points to be observed to ensure EMC-correct electrical installation. Use only screened/armoured motor cables and screened/armoured control cables. Connect the screen to earth at both ends. Avoid installation with twisted screen ends (pigtails), since this ruins the screening effect at high frequencies. Use the cable clamps providedinstead. It is important to ensure good electrical contact from the installation plate through the installation screws to the metal cabinet of the frequency converter. Use starwashers and galvanically conductive installation plates. Do not use unscreened/unarmoured motor cables in the installation cabinets. MG.8.F.02 - VLT is a registered Danfoss trademark 7

9 30BB76.0 PLC etc. Panel Output contactor etc. PLC Earthing rail Cable insulation stripped Min. 6 mm 2 Equalizing cable Control cables All cable entries in one side of panel Motor cable Mains-supply L L2 L3 PE Reinforced protective earth Illustration.3 EMC-correct Electrical Installation Min. 200mm between control cable, mains cable and between mains motor cable Motor, 3 phases and Protective earth For North America use metal conduits instead of shielded cables. 8 MG.8.F.02 - VLT is a registered Danfoss trademark

10 .3.8 Control Terminals IP V kW: 30BB622.0 Control terminals: Illustration.5 shows all control terminals of the frequency converter. Applying Start (term. 8), connection between terminal 2-27 and an analog reference (term. 53 or 54 and 55) make the frequency converter run. BUS TER. OFF ON BB985.0 Illustration.4 Location of Control Terminals COMM. GND P N DIGI IN DIGI IN DIGI IN/OUT DIGI IN/OUT 0/4-20mA A OUT / DIG OUT Illustration.5 Control Terminals 0V/20mA IN 0V/20mA IN 0V OUT 0/4-20mA A OUT / DIG OUT V COM A IN COM DIG IN. Place a screwdriver behind the terminal cover to activate snap. 2. Tilt the screwdriver outwards to open the cover. IP V 30-90kW. 30BB Place a screwdriver behind the terminal cover to activate snap. 2. Tilt the screwdriver outwards to open the cover. Digital input 8, 9 and 27 mode is set in 5-00 Terminal 8 Digital Input (PNP is default value) and digital input 29 mode is set in 5-03 Digital Input 29 Mode (PNP is default value). MG.8.F.02 - VLT is a registered Danfoss trademark 9

11 .3.9 Electrical Overview 3 Phase power input L L2 L3 PE PE U V W Motor 30BB984.0 UDC- Not present on all power sizes UDC+ +0Vdc 0-0Vdc- 0/4-20 ma 50 (+0V OUT) 53 (A IN) relay V AC 3A 0-0Vdc- 0/4-20 ma 54 (A IN) 55 (COM A IN/OUT) 42 0/4-20mA A OUT / DIG OUT 45 0/4-20mA A OUT / DIG OUT 04 relay V AC 3A 2 (+24V OUT) 8 (DIGI IN) 9 (DIGI IN) 20 (COM D IN) 27 (DIGI IN/DIGI OUT) 29 (DIGI IN/ DIGI OUT) 24V 0V 24V 0V 24V (NPN) OV (PNP) 24V (NPN) OV (PNP) 24V (NPN) OV (PNP) 24V (NPN) OV (PNP) Bus ter. 2 Bus ter. ON RS-485 Interface ON=Terminated OFF=Unterminated 0 (N PS-485) 69 (P RS-485) 68 (Com RS-485 ) 6 (PNP)-Source (NPN)-Sink RS-485 Do not connect shield to 6 on 6,7 and 8 unites NOTE Please note there is no access to UDC- and UDC+ on the following units: IP V 30-90kW 0 MG.8.F.02 - VLT is a registered Danfoss trademark

12 .4 Programming A number of information can be read from the display..4. Programming with the Local Control Panel (LCP) NOTE The frequency converter can also be programmed from a PC via RS485 com-port by installing the MCT-0 Set-up Software. This software can either be ordered using code number 30B000 or downloaded from the Danfoss Web site: softwaredownload The following instructions are valid for the FC LCP. The LCP is divided into four functional sections. Parameter number and name. 2 Parameter value. 3 Set-up number shows the active set-up and the edit setup. If the same set-up acts as both active and edit set-up, only that set-up number is shown (factory setting). When active and edit set-up differ, both numbers are shown in the display (2). The number flashing, indicates the edit set-up. 4 Motor direction is shown to the bottom left of the display indicated by a small arrow pointing either clockwise or counterclockwise. 5 The triangle indicates if the LCP is in status, quick menu or main menu A. Alphanumeric display B. Menu key C. Navigation keys and indicator lights (LEDs) D. Operation keys and indicator lights (LEDs) A B C Com On -20 Motor Power [2] 0.2kW-0.6HP Warn Alarm Menu Back Status OK Quick Menu Main Menu 2 30BB B. Menu Key Use the menu key to select between status, quick menu or main menu. C. Navigation keys and indicator lights (LEDs) 6 Com led: Flashes when bus communication is communicating. 7 Green LED/On: Control section is working. 8 Yellow LED/Warn.: Indicates a warning. 9 Flashing Red LED/Alarm: Indicates an alarm. 0 [Back]: For moving to the previous step or layer in the navigation structure Arrows [ ] [ ]: For maneuvering between parameter groups, parameters and within parameters. Can also be used for setting local reference. 2 [OK]: For selecting a parameter and for accepting changes to parameter settings D. Operation keys and indicator lights (LEDs) D Hand On Off Reset Auto On A. Alpha Numeric Display The LCD-display is back-lit with 2 alpha-numeric lines. All data is displayed on the LCP. 3 [Hand on]: Starts the motor and enables control of the frequency converter via the LCP. NOTE Please note that terminal 27 Digital Input (5-2 Terminal 27 Digital Input) has coast inverse as default setting. This means that [Hand On] will not start the motor if there is no 24V to terminal 27, so please connect terminal 2 to terminal [Off/Reset]: Stops the motor (off). If in alarm mode the alarm will be reset. 5 [Auto on]: Frequency converter is controlled either via control terminals or serial communication. MG.8.F.02 - VLT is a registered Danfoss trademark

13 At power-up At the first power-up the user is asked to choose preferred language. Once selected this screen will never be shown again in the following powerups, but language can still be changed in 0-0 Language. Select Language [ 0 ] English 30BB The Start-up Wizard for Open Loop Applications The built in wizard menu guides the installer through the set up of the drive in a clear and structured manner in order to setup an open loop application. A open loop application is here an application with a start signal, analog reference (voltage or current) and optionally also relay signals (but no feed back signal from the process applied). FC +24V 2 DIG IN 8 DIG IN 9 COM DIG IN 20 DIG IN 27 DIG IN 29 Start 30BB V A IN A IN COM A OUT / D OUT A OUT / D OUT R2 R V Reference The wizard will initially be shown after power up until any parameter has been changed. The wizard can always be accessed again through the quick menu. Press [OK] to start the wizard. If [BACK] is pressed, the FC will return to the status screen. Press OK to start Wizard Push Back to skip it 30BB MG.8.F.02 - VLT is a registered Danfoss trademark

14 At power up the user is asked to choose the prefered laguage. - the HVAC FC 0 Wizard starts Select Regional Settings [0] Power kw/50 Hz 4 30BB993.0 Select language [] English Menu Status Quick Menu On Warn Alarm Back OK Main Menu Grid Type V/50Hz/Delta 5 Asynchronous Motor Set Motor Power.0 kw 7 Set Motor Voltage 0050 V 8 Hand On Off Reset Power Up Screen OK Auto On Set Motor Frequency 0050 Hz Set Motor Current A The next screen will be the Wizard screen. On Press OK to start Wizard Press Back to skip it Warn Menu Alarm Hand On Back Status OK Off Reset Quick Menu Wizard Screen Main Menu Auto On if OK Set Motor Nominal Speed 420 RPM Set Motor Speed Low Limit 006 Hz Set Motor Speed High Limit 0050 Hz Set Ramp Ramp Up Time 0003 s Set Ramp Ramp Down Time 0003 s Active Flying start? [0] Disable if Back Current 22 Select Terminal 53 Mode [0] Current Voltage Hz 0.0 kw Menu Status Quick Menu Main Menu Set Terminal 53 Low Current 04.66A Set Terminal 53 High Current 3.30A Set Terminal 53 Low Voltage 0050 V Set Terminal 53 High Voltage 0220 V On Warn Alarm Hand On Back Status Screen The Wizard can always be reentered via the Quick Menu! Wizard completed Auto Motor Tuning OK AMA running Press OK to accept 34 Press OK Hz 0.0 kw OK Off Reset Auto On (Do not AMA) AMA OK Set Minimum Reference 006 Hz Set Maximum Reference 0050 Hz Select Function of Relay [0] No function Select Function Relay 2 [0] No function Automatic Motor Adaption (AMA) [] Enable Do AMA AMA failed AMA Failed MG.8.F.02 - VLT is a registered Danfoss trademark 3

15 The FC Start-up Wizard for Open Loop Applications No & Name Range Default Function 0-03 Regional Settings [0] International [] US 0-06 Grid Type 0] V/50Hz/IT-grid [] V/50Hz/Delta [2] V/50Hz [0] V/50Hz/IT-grid [] V/50Hz/Delta [2] V/50Hz [20] V/50Hz/IT-grid [2] V/50Hz/Delta [22] V/50Hz [30[ V/50Hz/IT-grid [3] V/50Hz/Delta [32[ V/50Hz [00] V/60Hz/IT-grid [0] V/60Hz/Delta [02] V/60Hz [0] V/60Hz/IT-grid [] V/60Hz/Delta [2] V/60Hz [20] V/60Hz/IT-grid [2] V/60Hz/Delta [22] V/60Hz [30] V/60Hz/IT-grid [3] V/60Hz/Delta [32] V/60Hz 0 Size related Select operating mode for restart upon reconnection of the drive to mains voltage after power down -20 Motor Power 0.2-0kW/0.6-50hp Size related Enter motor power from nameplate data -22 Motor Voltage V Size related Enter motor voltage from nameplate data -23 Motor Frequency Hz Size related Enter motor frequency from nameplate data -24 Motor Current A Size related Enter motor current from nameplate data -25 Motor Nominal Speed 4-2 Motor Speed Low Limit [Hz] 4-4 Motor Speed High Limit [Hz] 3-4 Ramp Ramp up time 3-42 Ramp Ramp down time -73 Flying Start [0] Disabled RPM Size related Enter motor nominal speed from nameplate data Hz 0 Hz Enter the minimum limit for low speed Hz 65 Hz Enter the maximum limit for high speed s Size related Ramp up time from 0 to rated -23 Motor Frequency s Size related Ramp down time from rated -23 Motor Frequency [] Enabled 6-9 Terminal 53 mode [0] Current 6-0 Terminal 53 Low Voltage 6- Terminal 53 High Voltage 6-2 Terminal 53 Low Current 6-3 Terminal 53 High Current [] Voltage to 0 0 Select Enable to enable the frequency converter to catch a spinning motor i.e. fan applications Select if terminal 53 is used for current- or voltage 0-0V 0.07V Enter the voltage that corresponds to the low input reference value 0-0V 0V Enter the voltage that corresponds to the high reference value 0-20mA 4 Enter the current that corresponds to the low reference value 0-20mA 20 Enter the current that corresponds to the high reference value 3-02 Minimum Reference The minimum reference is the lowest value obtainable by summing all references 4 MG.8.F.02 - VLT is a registered Danfoss trademark

16 No & Name Range Default Function 3-03 Maximum Reference The maximum reference is the lowest obtainable by summing all references 5-40 Function Relay [0] See 5-40 Function Relay Alarm Select the function to control output relay Function relay 5-40 Function Relay [] See 5-40 Function Relay Drive running Select the function to control output relay 2 Function relay -29 Auto Tune See -29 Auto Tune Off Performing an AMA optimizes motor performance MG.8.F.02 - VLT is a registered Danfoss trademark 5

17 Closed Loop Set-up Wizard Regional Settings [0] International 0-0 Configuration Mode [0] Open Loop Asynchronous Motor 30BB Motor Power.0 kw -22 Motor Voltage 0050 V -23 Motor frequency 0050 Hz -24 Motor current A -25 Motor nominal speed 420 RPM Motor speed low limit 006 Hz Motor speed high limit 0050 Hz Ramp ramp-up time 0003 s Ramp ramp-down time 0003 s 8-73 Flying Start [0] No 8a Feedback source [2] Analog in 54 This dialog is forced to be set to [2] Analog in Min Reference [] Max Reference [] Preset reference [0] [] Preset reference is the set-point Current Terminal 54 Mode [] Voltage mode Voltage Terminal 54 Low Current 4 ma 6-20 Terminal 54 Low Voltage 0,07 V Terminal 54 Low Ref./Feedb. Value 006 Hz Terminal 54 Filter time constant 0,0 s 6-24 Terminal 54 Low Ref./Feedb. Value 0 Hz Terminal 54 High Current 20 ma 6-25 Terminal 54 High Ref./Feedb. Value PI Normal/Inverse Control [0] Normal PI Start Speed 0 Hz PI Proportional Gain 0,0 s 6-2 Terminal 54 High Voltage 0 V 6-25 Terminal 54 High Ref./Feedb. Value 0050 Hz PI Integral Time 9999 s -29 Automatic Motor Adaption [] Enable Please note that Terminal 27 Digital Input (par. 5-2) has coast inverse as default setting. This means that AMA can not be performed if there is no 24V to terminal 27 so please connect terminal 2 to terminal MG.8.F.02 - VLT is a registered Danfoss trademark

18 Closed Loop Set-up Wizard No & Name Range Default Function 0-03 Regional Settings [0] International [] US 0-20 Motor power kW Size related Enter motor power from nameplate data -22 Motor Voltage V Size related Enter motor voltage from nameplate data -23 Motor Frequency Hz Size related Enter motor frequency from nameplate data -24 Motor Current A Size related Enter motor current from nameplate data -25 Motor Nominal Speed RPM Size related Enter motor nominal speed from nameplate data 4-2 Motor Speed Low Limit [Hz] Hz 0.0 Hz Enter the minimum limit for low speed 4-4 Motor Speed High Limit [Hz] Hz 65Hz Enter the maximum limit for high speed 3-4 Ramp Ramp up time s Size related Ramp up time from 0 to rated motor frequency par Ramp Ramp down time s Size related Ramp down time from rated motor frequency par. -23 to 0-73 Flying Start [0] Disabled 0 Select Enable to enable the drive to catch a spinning motor [] Enabled 3-02 Minimum Reference The minimum reference is the lowest value obtainable by summing all references 3-03 Maximum Reference The maximum reference is the highest value obtainable by summing all references 3-0 Preset Reference % 0 Enter the set point 6-29 Modo terminal 54 [0] Current Select if terminal 54 is used for current- or voltage input [] Voltage 6-20 Terminal 53 Low Voltage 0-0V 0.07V Enter the voltage that corresponds to the low reference value 6-2 Terminal 53 High Voltage 0-0V 0V Enter the voltage that corresponds to the low high reference value 6-22 Terminal 60 Low Current 0-20mA 4 Enter the current that corresponds to the high reference value 6-23 Terminal 60 High Current 0-20mA 20 Enter the current that corresponds to the high reference value 6-24 Terminal 60 Low Ref./Feedb. Value Enter the feedback value that corresponds to the voltage or current set in par. 6-20/ Terminal 60 High Ref./Feedb. Value Enter the feedback value that corresponds to the voltage or current set in par. 6-2/ Terminal 60 Filter Time 0-0 s 0.0 Enter the filter time comstant Constant 20-8 PI Normal/Inverse control [0] Normal [] Inverse 0 Select Normal [0] to set the process control to increase the output speed when the process error is positive. Select Inverse [] to reduce the output speed PI Start Speed 0-200Hz 0 Enter the motor speed to be attained as a start signal for commencement of PI control PI Proportional Gain Enter the process controller proportional gain. Quick control is obtained at high amplification. However if amplification os too great, the process may become unstable PID Integral Time s 999.0s Enter the process controller integral time. Obtain quick control through a short integral time, though if the integral time is too short, the process becomes unstable. An excessively long integral time disables the integral action. -29 Automatic Motor Adaption (AMA) Off Performing an AMA optimizes motor performance MG.8.F.02 - VLT is a registered Danfoss trademark 7

19 Motor Set-up The Quick Menu Motor Set-up guides through the needed motor parameters. No & Name Range Default Function 0-03 Regional Settings -20 Motor power -22 Motor Voltage -23 Motor Frequency -24 Motor Current -25 Motor Nominal Speed 4-2 Motor Speed Low Limit [Hz] 4-4 Motor Speed High Limit [Hz] 3-4 Ramp Ramp up time 3-42 Ramp Ramp down time -73 Flying Start [0] International [] US 0.2-0kW/ Hp 0 Size related Enter motor power from nameplate data V Size related Enter motor voltage from nameplate data Hz Size related Enter motor A RPM Size related Size related frequency from nameplate data Enter motor current from nameplate data Enter motor nominal speed from nameplate data Hz 0.0 Hz Enter the minimum limit for low speed 0-400HZ 65 Enter the maximum limit for high speed s Size related Ramp up time from 0 to rated motor frequency -23 Motor Frequency s Size related Ramp down time [0] Disabled [] Enabled from rated motor frequency -23 Motor Frequency to 0 0 Select Enable to enable the frequency converter to catch a spinning motor Changes Made Changes Made lists all parameters changed since factory setting. Only the changed parameters in current edit-setup are listed in changes made. If the parameter's value is changed back to factory setting's value from another different value, the parameter will NOT be listed in Changes Made.. Press [MENU] key to enter the Quick Menu until indicator in display is placed above Quick Menu. 2. Press [ ] [ ] to select either FC wizard, closed loop setup, motor setup or changes made, then press [OK]. 3. Press [ ] [ ] to browse through the parameters in the Quick Menu. 4. Press [OK] to select a parameter. 5. Press [ ] [ ] to change the value of a parameter setting. 6. Press [OK] to accept the change. 7. Press either [Back] twice to enter Status, or press [Menu] once to enter Main Menu. The Main Menu accesses all parameters.. Press [MENU] key until indicator in display is placed above Main Menu. 2. Use [ ] [ ] to browse through the parameter groups. 3. Press [OK] to select a parameter group. 4. Use [ ] [ ] to browse through the parameters in the specific group. 5. Press [OK] to select the parameter. 6. Use [ ] [ ] to set/change the parameter value. 8 MG.8.F.02 - VLT is a registered Danfoss trademark

20 .5 Cascade Controller.5. BASIC Cascade Controller Constant Speed Pumps (2) Variable Speed Pumps () Motor starter Pressure Sensor Frequency Converter with Cascade Controller The BASIC Cascade Controller is used for pump applications where a certain pressure ( head ) or level needs to be maintained over a wide dynamic range. Running a large pump at variable speed over a wide for range is not an ideal solution because of low pump efficiency and because there is a practical limit of about 25% rated full load speed for running a pump. In the BASIC Cascade Controller the frequency converter controls a variable speed motor as the variable speed pump (lead) and can stage up to two additional constant speed pumps on and off. By varying the speed of the initial pump, variable speed control of the entire system is provided. This maintains constant pressure while eliminating pressure surges, resulting in reduced system stress and quieter operation in pumping systems. 30BA362.0 event occurs. Selections include whenever an alternation timer expires, at a predefined time of day or when the lead pump goes into sleep mode. Staging is determined by the actual system load. A separate parameter limits alternation only to take place if total capacity required is > 50%. Total pump capacity is determined as lead pump plus fixed speed pumps capacities. Bandwidth Management In cascade control systems, to avoid frequent switching of fixed speed pumps, the desired system pressure is kept within a bandwidth rather than at a constant level. The Staging Bandwidth provides the required bandwidth for operation. When a large and quick change in system pressure occurs, the Override Bandwidth overrides the Staging Bandwidth to prevent immediate response to a short duration pressure change. An Override Bandwidth Timer can be programmed to prevent staging until the system pressure has stabilized and normal control established. When the Cascade Controller is enabled and running normally and the frequency converter issues a trip alarm, the system head is maintained by staging and destaging fixed speed pumps. To prevent frequent staging and destaging and minimize pressure fluxuations, a wider Fixed Speed Bandwidth is used instead of the Staging bandwidth..5.2 System Status and Operation If the lead pump goes into Sleep Mode, the function is displayed on the LCP. It is possible to alternate the lead pump on a Sleep Mode condition. Fixed Lead Pump The motors must be of equal size. The BASIC Cascade Controller allows the frequency converter to control up to 3 equal size pumps using the drives two built-in relays. When the variable pump (lead) is connected directly to the frequency converter, the other 2 pumps are controlled by the two built-in relays. When lead pump alternations is enabled, pumps are connected to the built-in relays and the frequency converter is capable of operating 2 pumps. Lead Pump Alternation The motors must be of equal size. This function makes it possible to cycle the frequency converter between the pumps in the system (maximum of 2 pumps). In this operation the run time between pumps is equalized reducing the required pump maintenance and increasing reliability and lifetime of the system. The alternation of the lead pump can take place at a command signal or at staging (adding another pump). The command can be a manual alternation or an alternation event signal. If the alternation event is selected, the lead pump alternation takes place every time the When the Cascade Controller is enabled, the operation status for each pump and the Cascade Controller is displayed by 25-8, Pump Status and 25-80, Cascade Status on the LCP. Information displayed includes: Pumps Status, is a read out of the status for the relays assigned to each pump. The display shows pumps that are disabled, off, running on the frequency converter or running on the mains/ motor starter. Cascade Status, is a read out of the status for the Cascade Controller. The display shows the Cascade Controller is disabled, all pumps are running off, fixed speed pumps are being staged/ de-staged and lead pump alternation is occurring. When all relays are de-energized, the first built-in relay to be energized will cut in the contactor corresponding to the pump controlled by the relay. E.g. RELAY cuts in contactor K, which becomes the lead pump. MG.8.F.02 - VLT is a registered Danfoss trademark 9

21 K blocks for K2 via the mechanical interlock preventing mains to be connected to the output of the frequency converter (via K). Auxiliary break contact on K prevents K3 to cut in. RELAY 2 controls contactor K4 for on/off control of the fixed speed pump. At alternation, both relays de-energize and now RELAY 2 will be energized as the first relay. 20 MG.8.F.02 - VLT is a registered Danfoss trademark

22 .5.3 Start/Stop Conditions Commands assigned to digital inputs. See Digital Inputs, parameter group 5-*. Variable speed pump (lead) Fixed speed pumps Start (SYSTEM START /STOP) Ramps up (if stopped and there is a Staging (if stopped and there is a demand) demand) Lead Pump Start Ramps up if SYSTEM START is active Not affected Coast (EMERGENCY STOP) Coast to stop Cut out (built in relays are de-energized) External Interlock Coast to stop Cut out (built in relays are de-energized) Function of buttons on LCP: Variable speed pump (lead) Fixed speed pumps Hand On Ramps up (if stopped by a normal stop Destaging (if running) command) or stays in operation if already running Off Ramps down Destaging Auto On Starts and stops according to commands via terminals or serial bus Staging/Destaging MG.8.F.02 - VLT is a registered Danfoss trademark 2

23 .5.4 Cascade Application Wizard 30BB983.0 Fix lead pump application without lead pump alternation Set par.2505 (Fixed Lead Pump) to [] Yes Press [Off Reset] on the LCP to stop the frequency conveter Set par.00(configuation Mode) to [3] Closed Loop Set par.302/303(min/max Reference) according to specific application Set par.35 (Reference Source) to [] Analog in 53 Verify par.69 (Terminal 53 mode) meets reference mode (Current or Voltage) Set par.2000 (Feedback Source) to [2] Analog in 54 Verify par.629 (Terminal 54 mode) meets feedback mode (Current or Voltage) Set par. 20-9* (PI Controller) for close-loop application (Please refer to close-loop wizard) Set par.2500 (Cascade Controller) to [] Enabled Press [Auto On] on LCP to run drive Please make sure par.36 and 37 is set to [0] No Function Alter lead pump application, lead pump can be alternated at staging Set par (Fixed Lead Pump) to [0] No Set par.2550 (Lead Pump Alternation) to [] At staging Set par.2555 (Alternate if Load<50%) to [0] Disabled 22 MG.8.F.02 - VLT is a registered Danfoss trademark

24 .6 Parameter Overview MG.8.F.02 - VLT is a registered Danfoss trademark 23

25 Parameter Overview 0-** Operation / Display 0-0* Basic Settings 0-0 Language *[0] English [] Deutsch [2] Francais [3] Dansk [4] Espanol [5] Italiano [28] Portuguese [255] No Text 0-03 Regional Settings *[0] International [] US 0-04 Operating State at Powerup *[0] Resume [] Forced stop, ref=old 0-06 GridType 0] V/50Hz/IT-grid [] V/50Hz/Delta [2] V/50Hz [0] V/50Hz/IT-grid [] V/50Hz/Delta [2] V/50Hz [20] V/50Hz/IT-grid [2] V/50Hz/Delta [22] V/50Hz [30] V/50Hz/IT-grid [3] V/50Hz/Delta [32] V/50Hz [00] V/60Hz/IT-grid [0] V/60Hz/Delta [02] V/60Hz [0] V/60Hz/IT-grid [] V/60Hz/Delta [2] V/60Hz [20] V/60Hz/IT-grid [2] V/60Hz/Delta [22] V/60Hz [30] V/50Hz/IT-grid [3] V/50Hz/Delta [32] V/50Hz 0-07 Auto DC Braking IT [0] Off *[] On 0-* Set-up Operations 0-0 Active Set-up *[] Set-up [2] Set-up 2 [9] Multi Set-up 0- Programming Set-up [] Set-up [2] Set-up 2 *[9] Active Set-up 0-2 Link Setups [0] Not linked *[20] Linked 0-3* LCP Readout 0-30 Custom Readout Unit [0] None *[] % [5] PPM [0] /Min [] RPM [2] Pulse/s [20] l/s [2] l/min [22] l/h [23] m3/s [24] m3/min [25] m3/h [30] kg/s [3] kg/min [32] kg/h [33] t/min [34] t/h [40] m/s [4] m/min [45] m [60] Degree Celsius [70] mbar [7] bar [72] Pa [73] kpa [74] m Wg [80] kw [20] GPM [2] gal/s [22] gal/min [23] gal/h [24] CFM [27] ft3/h [40] ft/s [4] ft/min [60] Degree Fahr [70] psi [7] lb/in2 [72] in WG [73] ft WG [80] HP 0-3 Custom Readout Min Value ,000,000.0, * Custom Readout Max Value ,000,000.0, * Display Text 0-38 Display Text Display Text 3 0-4* LCP Keypad 0-40 [Hand on] Key on LCP [0] Disabled *[] Enabled 0-44 [Off / Reset] Key on LCP [0] Disable All *[] Enable All [7] Enable Reset Only 0-42 [Auto on] Key on LCP [0] Disabled *[] Enabled 0-5* Copy/Save 0-50 LCP Copy *[0] No copy [] All to LCP [2] All from LCP [3] Size indep. from LCP 0-5 Set-up Copy *[0] No copy [] Copy from setup [2] Copy from setup 2 [9] Copy from Factory setup 0-6* Password 0-60 Main Menu Password 0-999, * 0 -** Load and Motor -0* General Settings -00 Configuration Mode *[0] Open loop [3] Closed loop -0 Motor Control Principle [0] U/f *[] VVC+ -03 Torque Characteristics *[] Variable torque [3] Auto Energy Optim. -06 Clockwise Direction *[0] Normal [] Inverse -20 Motor Power [2] 0.2kW - 0.6Hp [3] 0.8kW Hp [4] 0.25kW Hp [5] 0.37 kw Hp [6] 0.55 kw Hp [7] 0.75 kw -.00Hp [8].0 kw -.50Hp [9].50 kw Hp [0] 2.20 kw Hp [] 3.00 kw Hp [2] 3.70 kw Hp [3] 4.00 kw Hp [4] 5.50 kw Hp [5] 7.50 kw - 0.0Hp [6].00 kw Hp [7] 5.00kW - 20Hp [8] 8.5kW - 25Hp [9] 22kW - 30Hp [20] 30kW - 40Hp [2] 37kW-50Hp [22] 45kW-60Hp [23] 55kW-75Hp [24] 75kW-00Hp [25] 90kW-20Hp [26] 0kW-50Hp -22 Motor Voltage V -23 Motor Frequency , *(50)Hz -24 Motor Current (26.00), [A] -25 Motor Nominal Speed 00 rpm rpm, -29 Automatic Motor Adaption (AMA) *[0] Off [] Enable Complete AMA [2] Enable Reduced AMA -3* Adv. Motor Data I -30 Stator Resistance (Rs) ohm ohm -33 Stator Leakage Reactance (X) ohm ohm -35 Main Reactance (Xh) ohm -39 Motor Poles 2-00, * 4-4* Adv. Motor Data II -42 Motor Cable Length 0-50, * 50m -43 Motor Cable Length Feet 0-43, * 44-5* Load Indep. Setting -50 Motor Magnetisation at Zero Speed 0-300, * 00% -52 Min Speed Normal Magnetising [Hz] , * U/f Characteristic - U 0-999V, *0V -56 U/f Characteristic - F 0-400Hz, *(0) -6* Load Depend. Setting -62 Slip Compensation %, *0% -63 Slip Compensation Time Constant s, * Resonance Dampening 0-500%, * Resonance Dampening Time Constant s, * * Start Adjustments -7 Start Delay s, * MG.8.F.02 - VLT is a registered Danfoss trademark

26 Parameter Overview -72 Start Function [0] DC Hold/delay time *[2] Coast/delay time -73 Flying Start *[0] Disabled [] Enabled -8* Stop Adjustments -80 Function at Stop *[0] Coast [] DC hold/motorpreheat -82 Min Speed for Function at Stop [Hz] Hz, * 0.0-9* Motor Temperature -90 Motor Thermal Protection *[0] No protection [] Thermistor warning [2] Thermistor trip [3] ETR warning [4] ETR trip -93 Thermistor Resource *[0] None [] Analog input 53 [6] Digital input 29 2-** Brakes 2-0* DC-Brake 2-00 DC Hold/Motor Preheat Current 0-60%, * DC Brake Current 0-50%, * DC Braking Time s, * DC Brake Cut In Speed Hz, * * Brake Energy Funct. 2-7 Over-voltage Control [0] Disabled *[2] Enabled 3-** Reference / Ramps 3-0* Reference Limits 3-02 Minimum Reference ( ) , * Maximum Reference ( ) , * * References 3-0 Preset Reference %, * Jog Speed [Hz] Hz, * Preset Relative Reference , * Reference Resource [0] No function *[] Analog in 53 [2] Analog in 54 [] Local bus reference 3-6 Reference 2 Resource [0] No function [] Analog in 53 *[2] Analog in 54 [] Local bus reference 3-7 Reference 3 Resource [0] No function [] Analog in 53 [2] Analog in 54 *[] Local bus reference 3-4* Ramp 3-4 Ramp Ramp up Time s, *Size related 3-42 Ramp Ramp Down Time s, *Size related 3-5* Ramp Ramp 2 Ramp up Time s, *Size related 3-52 Ramp 2 Ramp down Time s, *Size related 3-8* Other Ramps 3-80 Jog Ramp Time s, *Size related 3-8 Quick Stop Ramp Time s, *Size related 4-** Limits / Warnings 4-* Motor Limits 4-0 Motor Speed Direction [0] Clockwise *[2] Both directions 4-2 Motor Speed Low Limit [Hz] Hz, *0.0Hz 4-4 Motor Speed High Limit [Hz] Hz, *65.0Hz 4-8 Current Limit 0-300%, *0% 4-9 Max Output Frequency Hz, * * Adj. Warnings Warning Freq. Low hZ, * Warning Freq. High Hz, * * Adj. Warnings 4-50 Warning Current Low A, * Warning Current High A, * Warning Reference Low , * Warning Reference High , * Warning Feedback Low , * Warning Feedback High , * Missing Motor Phase Function [0] Off *[] On 4-6* Speed Bypass 4-6 Bypass Speed From [Hz] , * Bypass Speed To [Hz] , * Semi-Auto Bypass Set-up *[0] Off [] Enable 5-** Digital In/Out 5-0* Digital I/O mode 5-00 Digital Input Mode *[0] PNP [] NPN 5-0 Terminal 27 I/O Mode *[0] Input [] Output 5-02 Terminal 29 I/O Mode *[0] Input [] Output 5-03 Digital Input 29 Mode *[0] PNP [] NPN 5-* Digital Inputs 5-0 Terminal 8 Digital Input [0] No operation [] Reset [2] Coast inverse [3] Coast and reset inverse [4] Quick stop inverse [5] DC-brake inverse [6] Stop inverse [7] External Interlock *[8] Start [9] Latched start [0] Reversing [] Start reversing [4] Jog [6] Preset ref bit 0 [7] Preset ref bit [8] Preset ref bit 2 [9] Freeze reference [20] Freeze output [2] Speed up [22] Speed down [23] Set-up select bit 0 [34] Ramp bit 0 [37] Fire mode [52] Run permissive [53] Hand Start [54] Auto start [60] Counter A (up) [6] Counter A (down) [62] Reset Counter A [63] Counter B (up) [64] Counter B (down) [65] Reset Counter B [20] Lead Pump Start [2] Lead Pump Alternation [30] Pump Interlock [3] Pump 2 Interlock [32] Pump 3 Interlock 5- Terminal 9 Digital Input See par. 5-0, *[0] No operation 5-2 Terminal 27 Digital Input See par. 5-0, *[2] Coast inverse 5-3 Terminal 29 Digital Input See par. 5-0, *[4 Jog] 5-3* Digital Outputs 5-30 Terminal 27 Digital Output [0] No operation [] Control ready [2] Drive ready [3] Drive ready/remote control [4] Standby/no warning [5] Drive running [6] Running/no warning [7] Run in range/no warning [8] Run on ref/no warning [9] Alarm [0] Alarm or warning [2] Out of current range [3] Below rurrent, low [4] Above current, high [9] Below feedback, low [20] Above feedback, high [2] Thermal warning [22] Ready, no thermal warning [23] Remote, ready, no thermal warning 24] Ready, Voltage OK [25] Reverse [26] Bus OK [28] Brake, no brake warning [29] Brake ready, no fault [30] Brake fault (IGBT) [32] Mech brake control [35] External interlock [36] Control word bit [37] Control word bit 2 [45] Bus Control [60] Comparator 0 [6] Comparator [62] Comparator 2 [63] Comparator 3 [64] Comparator 4 [65] Comparator 5 [70] Logic rule 0 [7] Logic rule [72] Logic rule 2 [73] Logic rule 3 MG.8.F.02 - VLT is a registered Danfoss trademark 25

27 Parameter Overview [74] Logic rule 4 [75] Logic rule 5 [80] SL digital output A [8] SL digital output B [82] SL digital output C [83] SL digital output D [60] No alarm [6] Running reverse [65] Local ref. active [66] Remote ref. active [67] Start command active [68] Drive in hand mode [69] Drive in auto mode [93] Sleep mode [94] Broken belt function [96] Fire mode [98] Drive bypass [200] Full capacity [20] Pump running [202] Pump 2 running [203] Pump 3 running 5-3 Terminal 29 Digital Output see par On Delay, Digital Output s, *0.0 s 5-35 Off Delay, Digital Output s, *0.0 s 0.00 ~ secs 5-4* Relays 5-40 Function Relay *[0] No operation [] Control ready [2] Drive ready [3] Drive ready/remote control [4] Enable / no warning [5] VLT running [6] Running / no warning [7] Run in range/no warning [8] Run on ref/no warning [9] Alarm [0] Alarm or warning [2] Out of current range [3] Below current, low [4] Above current, high [6] Below frequency, low [7] Above frequency, high [9] Below feedback, low [20] Above feedback, high [2] Thermal warning [22] Ready, no thermal warning [23] Remote, ready, no thermal warning [24] Ready, Voltage OK [25] Reverse [26] Bus OK [35] External Interlock [36] Control word bit [37] Control word bit 2 [45] Bus Control [60] Comparator 0 [6] Comparator [62] Comparator 2 [63] Comparator 3 [64] Comparator 4 [65] Comparator 5 [70] Logic rule 0 7] Logic rule [72] Logic rule 2 [73] Logic rule 3 [74] Logic rule 4 [75] Logic rule 5 [80] SL digital output A [8] SL digital output B [82] SL digital output C [83] SL digital output D [60] No alarm [6] Running reverse [65] Local ref. active [66] Remote ref. active [67] Start command activ [68] Drive in hand mode [69] Drive in auto mode [93] Sleep Mode [94] Broken Belt Function [96] Fire Mode [98] Drive Bypass [2] Cascade Pump [22] Cascade Pump 2 [23] Cascade Pump On Delay, Relay s, *0.0 s 5-42 Off Delay, Relay 0.00 ~ s, *0.0s 5-5* Pulse Input 5-9* Bus Controlled 5-90 Digital and Relay Bus Control 0-0xFFFFFFFF, * 0 6-** Analog In/Out 6-0* Analog I/O Mode 6-00 Live Zero Timeout Time - 99s, * 05-5* Pulse Input 5-9* Bus Controlled 5-90 Digital and Relay Bus Control 0-0xFFFFFFFF, * 0 6-** Analog In/Out 6-0* Analog I/O Mode 6-00 Live Zero Timeout Time - 99s, * Live Zero Timeout Function *[0] Off [] Freeze output [2] Stop [3] Jogging [4] Max. speed [5] Stop and trip 6-* Analog Input Terminal 53 Low Voltage V, * Terminal 53 High Voltage V, * Terminal 53 Low Current , * 4.00mA 6-3 Terminal 53 High Current , * 20.00mA 6-4 Terminal 53 Low Ref./Feedb. Value , * Terminal 53 High Ref./Feedb. Value , * Terminal 53 Filter Time Constant s, * Terminal 53 mode [0] Current mode *[] Voltage mode 6-2* Analog Input Terminal 54 Low Voltage V, * Terminal 54 High Voltage V, * Terminal 54 Low Current , * 4.00mA 6-23 Terminal 54 High Current , * 20.00mA 6-24 Terminal 54 Low Ref./Feedb. Value , * Terminal 54 High Ref./Feedb. Value , * Terminal 54 Filter Time Constant , * Terminal 54 mode [0] Current mode [0] Current mode *[] Voltage mode 6-7* Analog Output Terminal 45 Mode *[0] 0-20 ma [] 4-20 ma [2] Digital Output 6-7 Terminal 45 Analog Output *[0] No operation [00] Output frequency [0] Reference [02] Feedback [03] Motor current [06] Power [39] Bus Control 6-72 Terminal 45 Digital Output *[0] No operation [] Control ready [2] Drive ready [3] Drive ready/remote control [4] Standby / no warning [5] Drive running [6] Running / no warning [7] Run in range/no warning [8] Run on ref/no warning [9] Alarm [0] Alarm or warning [2] Out of current range [3] Below current, low [4] Above current, high [9] Below feedback, low [20] Above feedback, high [2] Thermal warning [22] Ready, no thermal warning [23] Remote, ready, no thermal warning [24] Ready, Voltage OK [25] Reverse [26] Bus OK [35] External Interlock [45] Bus Control [60] Comparator 0 [6] Comparator [62] Comparator 2 [63] Comparator 3 [64] Comparator 4 [65] Comparator 5 [70] Logic rule 0 [7] Logic rule [72] Logic rule 2 [73] Logic rule 3 [74] Logic rule 4 [75] Logic rule 5 [80] SL digital output A [8] SL digital output B [82] SL digital output C [83] SL digital output D [60] No alarm [6] Running reverse [65] Local ref. active [66] Remote ref. active [67] Start command activ [68] Drive in hand mode [69] Drive in auto mode [93] Sleep Mode [94] Broken Belt Function [96] Fire Mode [98] Bypass Mode [200] Full capacity [20] Pump running [202] Pump 2 running [203 Pump 3 running 26 MG.8.F.02 - VLT is a registered Danfoss trademark

28 Parameter Overview 6-73 Terminal 45 Output Min Scale %, * Terminal 45 Output Max Scale %, * Terminal 45 Output Bus Control %, * * Analog Output Terminal 42 Mode *[0] 0-20 ma [] 4-20 ma [2] Digital Output 6-9 Terminal 42 Analog Output *[0] No operation [00] Output frequency [0] Reference [02] Feedback [03] Motor current [05] TorquereltoRated [06] Power [39] Bus Control 6-92 Terminal 42 Digital Output *[0] No operation [] Control ready [2] Drive ready [3] Drive ready/remote control [4] Enable / no warning [5] Drive running [6] Running / no warning [7] Run in range/no warning [8] Run on ref/no warning [9] Alarm [0] Alarm or warning [2] Out of current range [3] Below current, low [4] Above current, high [9] Below feedback, low [20] Above feedback, high [2] Thermal warning [22] Ready, no thermal warning [23] Remote, ready, no thermal warning [24] Ready, Voltage OK [25] Reverse [26] Bus OK [35] External Interlock [45] Bus Control [60] Comparator 0 [6] Comparator [62] Comparator 2 [63] Comparator 3 [64] Comparator 4 [65] Comparator 5 [70] Logic rule 0 [7] Logic rule [72] Logic rule 2 [73] Logic rule 3 [74] Logic rule 4 [75] Logic rule 5 [80] SL digital output A [8] SL digital output B [82] SL digital output C [83] SL digital output D [60] No alarm [6] Running reverse [65] Local ref. active [66] Remote ref. active [67] Start command activ [68] Drive in hand mode [69] Drive in auto mode [93] Sleep Mode [94] Broken Belt Function [96] Fire Mode [98] Drive Bypass [200] Full capacity [20] Pump running [202] Pump 2 running [203 Pump 3 running 6-93 Terminal 42 Output Min Scale %, * Terminal 42 Output Max Scale %, * Terminal 42 Output Bus Control %, * ** Comm. and Options 8-0* Comm. General Settings 8-0 Control Site *[0] Digital and ctrl.word [] Digital only [2] Controlword only 8-02 Control Source [0] None *[] FC Port 8-03 Control Timeout Time s, * Control Timeout Function *[0] Off [] Freeze output [2] Stop [3] Jogging [4] Max. speed [5] Stop and trip [20] N2 Override Release 8-06 Reset Control Word Timeout *[0] No function [] Do reset 8-3* FC Port Settings 8-30 Protocol *[0] FC [2] Modbus RTU [3] Metasys N2 [4] FLN [5] BACNet 8-3 Address - 247, * 8-32 FC Port Baud Rate [0] 2400 Baud [] 4800 Baud *[2] 9600 Baud [3] 9200 Baud [4] Baud [5] Baud [6] Baud [7] 5200 Baud 8-33 FC Port Parity *[0] Even Parity, Stop Bit [] Odd Parity, Stop Bit [2] No Parity, Stop Bit [3] No Parity, 2 Stop Bits 8-35 Minimum Response Delay s, * Max Response Delay s, * Max Inter-char delay s, * * Digital/Bus 8-50 Coasting Select [0] Digital input [] Bus [2] Logic AND *[3] Logic OR 8-5 Quick Stop Select [0] Digital input [] Bus [2] Logic AND *[3] Logic OR 8-52 DC Brake Select [0] Digital input [] Bus [2] Logic AND *[3] Logic OR 8-53 Start Select [0] Digital input [] Bus [2] Logic AND *[3] Logic OR 8-54 Reversing Select [0] Digital input [] Bus [2] Logic AND *[3] Logic OR 8-55 Set-up Select [0] Digital input [] Bus [2] Logic AND *[3] Logic OR 8-56 Preset Reference Select [0] Digital input [] Bus [2] Logic AND *[3] Logic OR 8-7* Bacnet 8-70 BACnet Device Instance 0-0x400000UL, * 8-72 MS/TP Maxmaster 0-27, * MS/TP Max Info Frames , * 8-74 "I am" Service *[0] Send at power-up [] Continuously 8-75 Intialisation Password 8-8* FC Port Diagnostics 8-80 Bus Message Count , * Bus Error Count , * Slave Message Rcvd , * Slave Error Count , * Slave Message Sent , * Slave Timeout Errors , * Reset FC port Diagnostics *[0] Do not reset [] Reset counter 8-9* Bus Feedback 8-94 Bus feedback , * 0 3-** Smart Logic 3-0* SLC Settings 3-00 SL Controller Mode *[0] Off [] On 3-0 Start Event [0] False [] True [2] Running [3] In range [4] On reference [7] Out of current range [8] Below Ilow [9] Above Ihigh [6] Thermal warning [7] Mains out of range [8] Reversing [9] Warning [20] Alarm (trip) [2] Alarm (trip lock) [22] Comparator 0 [23] Comparator [24] Comparator 2 [25] Comparator 3 [26] Logic rule 0 [27] Logic rule [28] Logic rule 2 [29] Logic rule 3 [33] Digital input 8 MG.8.F.02 - VLT is a registered Danfoss trademark 27

MAKING MODERN LIVING POSSIBLE. Quick Guide VLT HVAC Basic Drive

MAKING MODERN LIVING POSSIBLE. Quick Guide VLT HVAC Basic Drive MAKING MODERN LIVING POSSIBLE Quick Guide VLT HVAC Basic Drive Contents Contents Quick Guide 2. Safety 2.. Warnings 2..2 Safety Instructions 2.2 Introduction 2.2. Available Literature 2.2.2 Approvals 2.2.3

More information

FREQUENCY CONVERTER FC101 (QUICK GUIDE)

FREQUENCY CONVERTER FC101 (QUICK GUIDE) FREQUENCY CONVERTER FC101 (QUICK GUIDE) INSTALLATION AND MAINTENANCE Content Page Safety instructions 2 IT system 3x230VAC 2 Connections 3 Control unit (LCP) 4 Manual operation 4 Reverse the direction

More information

MAKING MODERN LIVING POSSIBLE. Instruction VLT HVAC Basic Drive Cascade Controller

MAKING MODERN LIVING POSSIBLE. Instruction VLT HVAC Basic Drive Cascade Controller MAKING MODERN LIVING POSSIBLE Instruction VLT HVAC Basic Drive Cascade Controller 1.1 Cascade Controller Constant Speed Pumps (2) Variable Speed Pumps (1) Motor starter Illustration 1.1 Cascade Controller

More information

FLÄKTGROUP OFFERS A WIDE RANGE OF PER- MANENT MAGNET MOTORS (PM) AND FREQUENCY CONVERTERS FOR PLUG FANS. POWER RANGE IS FROM 0,8 KW TO 15 KW.

FLÄKTGROUP OFFERS A WIDE RANGE OF PER- MANENT MAGNET MOTORS (PM) AND FREQUENCY CONVERTERS FOR PLUG FANS. POWER RANGE IS FROM 0,8 KW TO 15 KW. CENTRIFLOW PUR 3D (A, PLUG B, C, D) FAN GMPM FC101 AND SLIDE IN FREQUENCY ROTOR CASSETTE CONVERTER QUICK GUIDE FLÄKTGROUP OFFERS A WIDE RANGE OF PER- MANENT MAGNET MOTORS (PM) AND FREQUENCY CONVERTERS

More information

FREQUENCY CONVERTER FC102 (QUICK GUIDE)

FREQUENCY CONVERTER FC102 (QUICK GUIDE) FREQUENCY CONVERTER FC102 (QUICK GUIDE) INSTALLATION AND MAINTENANCE Content Page Safety instructions 2 IT system 3x230VAC 2 Connections 3 Control unit (LCP) 4 Manual operation 4 Reverse the direction

More information

Operating Instructions Extended Cascade Controller MCO 101

Operating Instructions Extended Cascade Controller MCO 101 Operating Instructions Extended Cascade Controller MCO 101 VLT AQUA Drive FC 200 Extended Cascade Controller Option Contents Contents 1. Safety and precautions 3 Safety Instructions 3 Avoid unintended

More information

Safety Instructions 1-1 Avoid unintended Start General Description 2-2

Safety Instructions 1-1 Avoid unintended Start General Description 2-2 Contents Contents 1 Safety and precautions 1-1 Safety Instructions 1-1 Avoid unintended Start. 1-1 2 Introduction 2-1 General Description 2-2 3 Supported Configuration 3-1 Introduction 3-1 Fixed-speed

More information

1 Extended and Advanced Cascade Controller Option 3

1 Extended and Advanced Cascade Controller Option 3 VLT Operating Instructions Contents Contents Extended and Advanced Cascade Controller 3 How to read these Operating Instructions 3 High Voltage Warning 3 Safety Instructions 3 Avoid unintended Start 3

More information

TR150 DRIVE STANDARD FEATURES

TR150 DRIVE STANDARD FEATURES TR150 DRIVE STANDARD FEATURES The TR150 Drive The TR150 Drive Series is a microprocessor-based, high frequency IGBT-based, PWM AC drive with control functions and software designed solely for the unique

More information

AF-60 LP TM Micro Drive. Programming Guide

AF-60 LP TM Micro Drive. Programming Guide GE AF-60 LP TM Micro Drive Programming Guide Contents Contents 1 Safety 1-1 1.1.1 High Voltage Warning 1-1 1.1.2 Safety Instructions 1-1 1.1.3 Software Version and Approvals 1-1 1.1.4 General Warning 1-1

More information

Metasys N2 Instruction Manual VLT Adjustable Frequency Drive. 12/ Revision B

Metasys N2 Instruction Manual VLT Adjustable Frequency Drive. 12/ Revision B Metasys N2 Instruction Manual VLT 6000 Adjustable Frequency Drive 12/99-6110-00 Revision B 2 Table of Contents Overview Page Introduction... 5 About this Manual... 5 References... 5 Instructions Abbreviations

More information

MAKING MODERN LIVING POSSIBLE. VLT AQUA Drive Cascade Controller Options MCO 101/102 Operating Instructions

MAKING MODERN LIVING POSSIBLE. VLT AQUA Drive Cascade Controller Options MCO 101/102 Operating Instructions MAKING MODERN LIVING POSSIBLE VLT AQUA Drive Cascade Controller Options MCO 101/102 Operating Instructions Safety VLT AQUA Drive MCO 101/MCO 102 Safety WARNING HIGH VOLTAGE Frequency converters contain

More information

Operating Instructions

Operating Instructions Operating Instructions VLT Micro Drive FC 51 VLT Micro Drive FC 51 Operating Instructions Contents Contents 1. Safety 5 Safety Instructions 5 Approvals 5 General Warning 5 Avoid unintended Start 6 Before

More information

AF-600 FP AC Drive AC Adjustable Frequency Drive Guide-Form Specification

AF-600 FP AC Drive AC Adjustable Frequency Drive Guide-Form Specification AF-600 FP AC Drive AC Adjustable Frequency Drive Guide-Form Specification Contents 1.0 General Information 2.0 Operating Conditions 3.0 Standards 4.0 Input Power Section 5.0 Output Power Section 6.0 Drive

More information

Installation and Wiring Instructions... 9

Installation and Wiring Instructions... 9 Contents Safety and precautions... 3 Safety regulations... 4 Warning against unintended start... 4 Operation modes... 6 Cascade Control Operation... 6 Standard Cascade Control Mode... 7 Lead Pump Alternation...

More information

User Guide VLT Parallel Drive Modules

User Guide VLT Parallel Drive Modules ENGINEERING TOMORROW User Guide VLT Parallel Drive Modules 250 1200 kw vlt-drives.danfoss.com Contents User Guide Contents 1 Introduction 4 1.1 Purpose of the Manual 4 1.2 Additional Resources 4 1.3 Manual

More information

VLT 2800 DRIVE SPECIFICATIONS

VLT 2800 DRIVE SPECIFICATIONS VLT 2800 DRIVE SPECIFICATIONS Drive Input Power Input voltage 3 phase... 200 through 240, or 380 through 460; 3-phase all ratings 200 through 240, 1-phase through 2 HP Input voltage range for full output...

More information

Q9 ASD LOW VOLTAGE DRIVE

Q9 ASD LOW VOLTAGE DRIVE ASD LOW VOLTAGE DRIVE HVAC-MINDED, SYSTEM FRIENDLY RELIABLE Toshiba has manufactured pulse-width modulated drives since 1981 and is one of the few companies that manufactures both motors and drives in

More information

TR200 DRIVE STANDARD FEATURES

TR200 DRIVE STANDARD FEATURES TR200 DRIVE STANDARD FEATURES The TR200 Trane Drive The TR200 Drive Series is a microprocessorbased, high frequency IGBT-based, PWM AC drive with control functions and software designed solely for the

More information

VLT Micro Drive. Ready Set Go!

VLT Micro Drive. Ready Set Go! Despite its compact size and ease of installation, the VLT Micro Drive can deliver exceptional performance even in complex applications. 1 Well protected IP20 enclosure with NEMA/UL Type 1 optional; no

More information

AF-600 FP TM Fan & Pump Drive. (230V to 60HP, 460/575V to 125HP Operating Instructions

AF-600 FP TM Fan & Pump Drive. (230V to 60HP, 460/575V to 125HP Operating Instructions GE AF-600 FP TM Fan & Pump Drive (230V to 60HP, 460/575V to 125HP Operating Instructions Safety Safety WARNING HIGH VOLTAGE! Frequency converters contain high voltage when connected to AC mains input power.

More information

AF-60 LP TM Micro Drive

AF-60 LP TM Micro Drive GE Consumer & Industrial Electrical Distribution AF-60 LP TM Micro Drive Operating Instructions Contents 1 Safety 5 Safety Instructions 5 Software Version and Approvals 6 General Warning 7 Avoid unintended

More information

VLT 8000 AQUA. Installation. Mechanical installation

VLT 8000 AQUA. Installation. Mechanical installation Mechanical installation Please pay attention to the requirements that apply to integration and field mounting kit, see the below list. The information given in the list must be observed to avoid serious

More information

Optidrive Applications Support Library

Optidrive Applications Support Library Optidrive Applications Support Library Application Note Title AN-ODV-3-038 Related Products Optidrive Eco Overview Level 3 Modbus RTU Control and Register Mapping 1 Fundamental - No previous experience

More information

TR200 DRIVE WITH ELECTRONICALLY CONTROLLED BYPASS SYSTEM

TR200 DRIVE WITH ELECTRONICALLY CONTROLLED BYPASS SYSTEM TR200 DRIVE WITH ELECTRONICALLY CONTROLLED BYPASS SYSTEM TR200 DRIVE STANDARD FEATURES The TR200 Trane Drive The TR200 Drive Series is a microprocessorbased, high frequency IGBT-based, PWM AC drive with

More information

The VLT Micro Drive Small drive maximum strength and reliability

The VLT Micro Drive Small drive maximum strength and reliability MAKING MODERN LIVING POSSIBLE The VLT Micro Drive Small drive maximum strength and reliability Ready Set Go! Connect motor and power cables, turn the control knob, and watch the motor speed change. 12

More information

Standard Cascade Controller Setup... 38

Standard Cascade Controller Setup... 38 Contents Safety and precautions... 3 Safety regulations... 4 Warning against unintended start... 4 Operation modes... 6 Cascade Control Operation... 6 Standard Cascade Control Mode... 7 Master/Slave Cascade

More information

ADJUSTABLE SPEED DRIVES. Q9 Series

ADJUSTABLE SPEED DRIVES. Q9 Series ADJUSTABLE SPEED DRIVES Q9 Series Reliable & Configurable Reliable Toshiba has manufactured pulse-width modulated drives since 1981 and is one of the few companies that manufactures both motors and drives

More information

lnvertek Drives.com ct,ve ELECTRICAL SUPPLIERS LTD

lnvertek Drives.com ct,ve ELECTRICAL SUPPLIERS LTD lnvertek Drives.com ft ct,ve ELECTRICAL SUPPLIERS LTD OptidriveE2 Technical Product Guide 1.1 OVERVIEW Range IP20 IP66X (NON SWITCHED) IP66Y (SWITCHED) Supply Voltage Range Power Range 110 115 + / 10%

More information

PowerFlex 400 AC Drive Guide Specification

PowerFlex 400 AC Drive Guide Specification PowerFlex 400 AC Drive Guide Specification Adjustable Frequency Drives with Bypass 3.0 50HP @ 208V AC 3.0 350HP @ 480V AC PART 1 GENERAL 1.01 Quality Assurance A. The manufacturer shall have minimum 5

More information

VLT The Real Drive for HVAC. The VLT 6000 is a. totally new adjustable. frequency drive, with. control functions and. software designed solely

VLT The Real Drive for HVAC. The VLT 6000 is a. totally new adjustable. frequency drive, with. control functions and. software designed solely VLT 6000 The Real Drive for HVAC HVAC KEYPAD The VLT 6000 s new, user-friendly, HVAC keypad separates the Hand, Off and Auto functions for easy, logical control of the drive. Local control is easily accomplished

More information

ATV12HU22M3 variable speed drive ATV12-2.2kW - 3hp V - 3ph - with heat sink

ATV12HU22M3 variable speed drive ATV12-2.2kW - 3hp V - 3ph - with heat sink Characteristics variable speed drive ATV12-2.2kW - 3hp - 200..240V - 3ph - with heat sink Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly

More information

ATV12P075M3 variable speed drive ATV kW - 1hp V - 3ph - on base plate

ATV12P075M3 variable speed drive ATV kW - 1hp V - 3ph - on base plate Characteristics variable speed drive ATV12-0.75kW - 1hp - 200..240V - 3ph - on base plate Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly

More information

VLT Line Filter MCC 107 EMC Filter Series VLT Midi Drive FC 280 (K1 K3)

VLT Line Filter MCC 107 EMC Filter Series VLT Midi Drive FC 280 (K1 K3) These instructions provide technical and installation information for the MCC 107 EMC filter series. Only Danfoss qualified personnel is allowed to install this equipment. The personnel must be familiar

More information

INGERSOLL RAND Fixed Speed/Variable Speed Conversion COMMISSIONING AND OPERATION MANUAL

INGERSOLL RAND Fixed Speed/Variable Speed Conversion COMMISSIONING AND OPERATION MANUAL INGERSOLL RAND Fixed Speed/Variable Speed Conversion COMMISSIONING AND OPERATION MANUAL Before installing or starting this unit for the first time, this manual should be studied carefully to obtain a working

More information

Taco System Logic (TSL)

Taco System Logic (TSL) Taco System Logic (TSL) 302-370 Installation, Operation, and Maintenance Manual SUPERSEDES: June 27, 2014 EFFECTIVE: December 21, 2015 Table of Contents 1 ELECTRICAL CONNECTIONS................. 2 1.1

More information

MAKING MODERN LIVING POSSIBLE. VLT Micro Drive. Small drive maximum strength and reliability

MAKING MODERN LIVING POSSIBLE. VLT Micro Drive. Small drive maximum strength and reliability MAKING MODERN LIVING POSSIBLE New photo VLT Micro Drive Small drive maximum strength and reliability Ready Steady Go! Connect motor and power cables, turn the control knob, and watch the motor speed change

More information

ATV12H075M3 variable speed drive ATV kW - 1hp V - 3ph - with heat sink

ATV12H075M3 variable speed drive ATV kW - 1hp V - 3ph - with heat sink Product datasheet Characteristics ATV12H075M3 variable speed drive ATV12-0.75kW - 1hp - 200..240V - 3ph - with heat sink Complementary Main Range of product Altivar 12 Product or component type Product

More information

PART 1: GENERAL PART 2: PRODUCT. Effective: 12/29/10 Page 1 of 6 FECA-TE-104D

PART 1: GENERAL PART 2: PRODUCT. Effective: 12/29/10 Page 1 of 6 FECA-TE-104D Specification Number: 23 09 33 Product Name: FRENIC-Eco AC Drives for Variable Torque Fan & Pump Applications (1-125Hp at 208/230V and 1-900Hp at 460V) PART 1: GENERAL 1.01 SUMMARY A. This specification

More information

ATV12P037F1 variable speed drive ATV kW hp V - 1ph - on base plate

ATV12P037F1 variable speed drive ATV kW hp V - 1ph - on base plate Characteristics variable speed drive ATV12-0.37kW - 0.55hp - 100..120V - 1ph - on base plate Complementary Main Range of product Altivar 12 Product or component type Product destination Product specific

More information

ATV32HU11M2437 variable speed drive ATV32-1.1kW 200V - 1P - Bluetooth built-in - w heat sink

ATV32HU11M2437 variable speed drive ATV32-1.1kW 200V - 1P - Bluetooth built-in - w heat sink Characteristics variable speed drive ATV32-1.1kW 200V - 1P - Bluetooth built-in - w heat sink Main Range of product Altivar 32 Product or component type Product destination Product specific application

More information

1. Warnings Introduction Mechanical Installation Electrical Installation Application Examples...

1. Warnings Introduction Mechanical Installation Electrical Installation Application Examples... MCD 500 Operating Instructions Contents Contents 1. Warnings... 3 2. Introduction... 4 2.1. Feature List... 4 2.2. Type Code... 5 3. Mechanical Installation... 6 3.1. Mechanical Installation... 6 3.2.

More information

Metasys N2 Communications Protocol Operating Instructions

Metasys N2 Communications Protocol Operating Instructions Metasys N2 Communications Protocol Operating Instructions TR200 BAS-SVX26A-EN November 2009 BAS-SVX26B-EN Table of Contents Safety 1-1 High voltage warning 1-1 Before commencing repair work 1-4 Special

More information

VLT 6000 Start-Up. Oct 2003

VLT 6000 Start-Up. Oct 2003 VLT 6000 Start-Up 1 This presentation deals with the start-up of the Danfoss Drives VLT 6000 Variable Frequency Drive (VFD). It is designed to help you handle the start-up of the drive in normal applications.

More information

VLT Micro Drive. Small drive maximum strength and reliability

VLT Micro Drive. Small drive maximum strength and reliability 1 VLT Micro Drive Small drive maximum strength and reliability Well protected IP 20 enclosure No forced air flow through electronics High quality capacitors Hot pluggable LCP RFI Filter LCD display RS

More information

Built-in features Built-in simplicity Built for fans & pumps

Built-in features Built-in simplicity Built for fans & pumps GE Built-in features Built-in simplicity Built for fans & pumps AF-600 FP Fan & Pump Drives imagination at work Built for variable torque Specifically designed for fan and pump applications, the AF-600

More information

ATV12H018M2 variable speed drive ATV kW hp V - 1ph

ATV12H018M2 variable speed drive ATV kW hp V - 1ph Characteristics variable speed drive ATV12-0.18kW - 0.25hp - 200..240V - 1ph Complementary Main Range of product Altivar 12 Product or component type Product destination Product specific application Assembly

More information

1.1.1 Software Version Introduction About this Manual References 2

1.1.1 Software Version Introduction About this Manual References 2 Contents Contents 1 Overview 2 1.1.1 Software Version 2 1.1.2 Introduction 2 1.1.3 About this Manual 2 1.1.4 References 2 2 Instructions 3 2.1.1 Abbreviations and Definitions 3 2.1.2 Network Connection

More information

Section 16. Drives AF-650GP General Purpose Drive. Standard Specifications. Environmental Conditions. Logic Controller (LC) Sequencer

Section 16. Drives AF-650GP General Purpose Drive. Standard Specifications. Environmental Conditions. Logic Controller (LC) Sequencer Standard Specifications Environmental Conditions Enclosures IP20 Chassis, IP00 Chassis, IP21/NEMA 1, IP55/NEMA 12, IP54/NEMA 12, IP66/NEMA 4 Installation Location Do not install in locations where product

More information

QUICK START GUIDE. vau4/3. Frequency converter. operating instructions /12

QUICK START GUIDE. vau4/3. Frequency converter.   operating instructions /12 operating instructions QUICK START GUIDE Frequency converter vau4/3 28100241101 12/12 1 Safety information Warning of electrical shock! Danger to life! Electrical shock can cause serious injury or even

More information

Siemens Industrial s

Siemens Industrial s SINAMICS G130 Operating Instructions 05/2010 SINAMICS Siemens Industrial s Sinusoidal filter Safety information 1 General 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical

More information

MC Series Drives. Flexible, simple, rugged, robust!

MC Series Drives. Flexible, simple, rugged, robust! Drives Flexible, simple, rugged, robust! Our promise Commitment to Price Leadership Price leadership is serious business. It takes continuous life cycle management to make price leadership a sustainable

More information

Submittal Data Information SmartDRIVE HVAC Variable Speed Drives

Submittal Data Information SmartDRIVE HVAC Variable Speed Drives Submittal Data Information SmartDRIVE HVAC Variable Speed Drives 301-2131 EFFECTIVE: November 5, 2013 SUPERSEDES: October 1, 2012 JOB CONTRACTOR ENGINEER REP. ITEM NO. MOTOR DESIGN DATA HP Volts Frequency

More information

E510. Compact Drive IP 20/ NEMA HP (230V) 1-75 HP (460V)

E510. Compact Drive IP 20/ NEMA HP (230V) 1-75 HP (460V) E510 Compact Drive IP 20/ NEMA 1 0.5-40 HP (230V) 1-75 HP (460V) Control Mode Application & Selection Guide The E510 compact AC Drive is an easily configurable product that controls many motor driven applications.

More information

ATV320U04N4C variable speed drive ATV kW V - 3 phase - compact

ATV320U04N4C variable speed drive ATV kW V - 3 phase - compact Characteristics variable speed drive ATV320-0.37kW - 380...500V - 3 phase - compact Main Range of product Product or component type Product specific application Device short name Format of the drive Product

More information

1 How to Read these Operating Instructions 3. 3 Introduction to MCF 106 A/ B in C Option Adaptor 7

1 How to Read these Operating Instructions 3. 3 Introduction to MCF 106 A/ B in C Option Adaptor 7 MCF 106 A/ in C Option Adaptor Instruction Contents Contents 1 How to Read these Operating Instructions 3 Available Literature for VLT AutomationDrive FC 300 3 Approvals 4 Symbols 4 Abbreviations 4 2 Safety

More information

Rhino Buffer Module PSM24-BFM600S. Operating Instructions

Rhino Buffer Module PSM24-BFM600S. Operating Instructions Rhino Buffer Module PSM24-BFM600S Operating Instructions RHINO BUFFER MODULE PSM24-BFM600S Description The PSM24-BFM600S Buffer Module will hold the output voltage of a 24 VDC power supply after brownouts

More information

Quick Guide. VLT Micro Drive FC 51

Quick Guide. VLT Micro Drive FC 51 Quick Guide VLT Micro Drive FC 5 Quick Guide for VLT Micro FC 5. Quick Guide. Quick Guide... Available Literature NB! This quick guide contains the basic information necessary for installing and running

More information

Contents. Index 35. VLT HVAC Drive Metasys N2

Contents. Index 35. VLT HVAC Drive Metasys N2 VLT HVAC Drive Metasys N Contents Contents Introduction 3 About this Manual 3 References 3 Abbreviations and Definitions 5 Network Connection 5 Hardware Set-up 5 VLT Parameters 7 Analog s (AI) 3 Binary

More information

SORDS ELECTRIC ~ MA7200. Sensorless Vector AC Inverter.

SORDS ELECTRIC ~ MA7200. Sensorless Vector AC Inverter. www.sordselectric.com MA7200 Sensorless Vector AC Inverter Features and Benefits Sensorless Vector The MA7200 has precise speed and torque control for the most demanding system performance and simple set-up

More information

ATV310HU30N4E variable speed drive ATV310-3 kw - 4 hp V - 3 phase

ATV310HU30N4E variable speed drive ATV310-3 kw - 4 hp V - 3 phase Characteristics variable speed drive ATV310-3 kw - 4 hp - 380...460 V - 3 phase Complementary Product destination Main Range of product Altivar Easy 310 Product or component type Product specific application

More information

Small, powerful and built to last Save panel space and reduce installation costs

Small, powerful and built to last Save panel space and reduce installation costs MAKING MODERN LIVING POSSIBLE VLT Micro Drive Small, powerful and built to last Save panel space and reduce installation costs 150% motor torque for up to 1 minute enables you to use a smaller drive without

More information

Line reactors SINAMICS. SINAMICS G130 Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation

Line reactors SINAMICS. SINAMICS G130 Line reactors. Safety information 1. General. Mechanical installation 3. Electrical installation Safety information 1 General 2 SINAMICS SINAMICS G130 Mechanical installation 3 Electrical installation 4 Technical specifications 5 Operating Instructions Control version V4.7 04/2014 A5E00331462A Legal

More information

ABB Industrial Systems Inc. Standard Drives. ACH500-06E Effective 6/1/95

ABB Industrial Systems Inc. Standard Drives. ACH500-06E Effective 6/1/95 Part 1 - GENERAL ASEA BROWN BOVERI ABB Industrial Systems Inc. Standard Drives ACH500-06E Effective 6/1/95 Sample Specification for Adjustable Frequency Drives (2 to 400 HP) for Variable Torque Applications

More information

SMVector Additional I/O Module Installation and Operation Manual

SMVector Additional I/O Module Installation and Operation Manual SMVector Additional I/O Module Installation and Operation Manual About These Instructions This documentation applies to the optional Additional I/O module for the SMVector inverter and should be used in

More information

It is the installer's responsibility to follow all instructions in this manual and to follow correct electrical practice.

It is the installer's responsibility to follow all instructions in this manual and to follow correct electrical practice. MCD Modbus Module Instructions Important User Information INSTALLATION INSTRUCTIONS: MCD MODBUS MODULE Order Code: 175G9000 1. Important User Information Observe all necessary safety precautions when controlling

More information

Firmware Manual - EC Series Drives

Firmware Manual - EC Series Drives 1 Firmware Manual - EC Series Drives Doc Ver 1.01 Firmware ver: EC series drives For installation details refer to Hardware Manual Safety: Read safety instruction in hardware manual before installation

More information

Quantum III. Compact DC Drive Package. Slitter DC Drive Package. Quantum III

Quantum III. Compact DC Drive Package. Slitter DC Drive Package. Quantum III Compact DC Drive Package The delivers a DC drive package that integrates the intelligence of the Mentor II with a space saving design that incorporates many accessories typically required in the North

More information

ATV212WU55N4 variable speed drive ATV kW - 7.5hp - 480V - 3ph - EMC class C2 - IP55

ATV212WU55N4 variable speed drive ATV kW - 7.5hp - 480V - 3ph - EMC class C2 - IP55 Product data sheet Characteristics ATV212WU55N4 variable speed drive ATV212-5.5kW - 7.5hp - 480V - 3ph - EMC class C2 - IP55 Complementary Apparent power Prospective line Isc Continuous output current

More information

ATV61HC31Y variable speed drive ATV61-310kW - 690V - without EMC filter

ATV61HC31Y variable speed drive ATV61-310kW - 690V - without EMC filter Product data sheet Characteristics ATV61HC31Y variable speed drive ATV61-310kW - 690V - without EMC filter Main Range of product Altivar 61 Product or component type Product specific application Component

More information

ATV61QC31N4 variable speed drive ATV61Q - 315kW / 500HP V - IP20

ATV61QC31N4 variable speed drive ATV61Q - 315kW / 500HP V - IP20 Characteristics variable speed drive ATV61Q - 315kW / 500HP - 380...480V - IP20 Main Range of product Product or component type Device short name Product destination Product specific application Assembly

More information

50% VLT HVAC Basic Drive a compact and competitive solution for applications with basic needs. energy costs savings

50% VLT HVAC Basic Drive a compact and competitive solution for applications with basic needs.   energy costs savings MAKING MODERN LIVING POSSIBLE VLT HVAC Basic Drive a compact and competitive solution for applications with basic needs 50% energy costs savings Typically, a 20% reduction in speed will yield 50% energy

More information

A drive dedicated to variable speed control for HVAC applications

A drive dedicated to variable speed control for HVAC applications A drive dedicated to variable speed control for HVAC applications Designed for easy installation in mechanical fan and pump systems with reliable connectivity to building automation networks. VTAC 9 Drive

More information

2 Table of Contents 1. TABLE OF CONTENTS. 1. Table of Contents Introduction Wiring Diagram Terminals Review...

2 Table of Contents 1. TABLE OF CONTENTS. 1. Table of Contents Introduction Wiring Diagram Terminals Review... TPR-6 Temperature Protection Relay Instruction Manual Ver. June 1 st 2010 2 Table of Contents 1. TABLE OF CONTENTS 1. Table of Contents... 2 2. Introduction... 3 3. Wiring Diagram... 5 4. Terminals Review...

More information

ATV310H075N4E variable speed drive ATV kw - 1 hp V - 3 phase

ATV310H075N4E variable speed drive ATV kw - 1 hp V - 3 phase Characteristics variable speed drive ATV310-0.75 kw - 1 hp - 380...460 V - 3 phase Main Range of product Altivar Easy 310 Product or component type Product specific application Assembly style Device short

More information

ATV212WU40N4 variable speed drive ATV212-4kW - 5hp - 480V - 3ph - EMC class C2 - IP55

ATV212WU40N4 variable speed drive ATV212-4kW - 5hp - 480V - 3ph - EMC class C2 - IP55 Characteristics variable speed drive ATV212-4kW - 5hp - 480V - 3ph - EMC class C2 - IP55 Main Range of product Altivar 212 Product or component type Device short name Product destination Product specific

More information

Pump Data Sheet - Patterson HVAC Pumps Company: Intermountain Hydron Name: Cache County Mountain Crest Date: 09/24/2018

Pump Data Sheet - Patterson HVAC Pumps Company: Intermountain Hydron Name: Cache County Mountain Crest Date: 09/24/2018 Pump Data Sheet - Patterson HVAC Pumps Company: Intermountain Hydron Name: Cache County Mountain Crest Date: 09/24/2018 Tags: P-8 1800RPM Premium Efficient Motor 460/3/60 Pump and Motor Weight: 183lbs

More information

PROGRAMMING MANUAL IM262R00. AQUAVAR Intelligent Pump Controller START-UP GENIE PROGRAMMING MANUAL

PROGRAMMING MANUAL IM262R00. AQUAVAR Intelligent Pump Controller START-UP GENIE PROGRAMMING MANUAL PROGRAMMING MANUAL IM262R00 AQUAVAR Intelligent Pump Controller START-UP GENIE PROGRAMMING MANUAL TABLE OF CONTENTS Introduction 3 Chapter 1: Motor 4 Chapter 2: Application 5 2.1. Single Pump 5 2.2. Constant

More information

ATV61HU55M3 ATV61 5,5 kw 7,5HP 240V single phase EMC IP20

ATV61HU55M3 ATV61 5,5 kw 7,5HP 240V single phase EMC IP20 Product data sheet Characteristics ATV61HU55M3 ATV61 5,5 kw 7,5HP 240V single phase EMC IP20 Main Range of product Altivar 61 Product or component type Product specific application Component name Motor

More information

ATV320U07M2C variable speed drive ATV kW V - 1 phase - compact

ATV320U07M2C variable speed drive ATV kW V - 1 phase - compact Characteristics variable speed drive ATV320-0.75kW - 200...240V - 1 phase - compact Main Range of product Product or component type Product specific application Device short name Format of the drive Product

More information

Operating Instructions VLT DriveMotor FCP 106/FCM 106

Operating Instructions VLT DriveMotor FCP 106/FCM 106 MAKING MODERN LIVING POSSIBLE Operating Instructions VLT DriveMotor FCP 106/FCM 106 vlt-drives.danfoss.com Contents Operating Instructions Contents 1 Introduction 4 1.1 Purpose of the Manual 4 1.2 Additional

More information

PowerFlex 40 Sample Specification

PowerFlex 40 Sample Specification PowerFlex 40 Sample Specification GENERAL REFERENCES REGULATORY REQUIREMENTS Designed to meet the following specifications: NFPA 70 - US National Electrical Code NEMA ICS 3.1 - Safety standards for Construction

More information

dv/dt filter compact plus Voltage Peak Limiter SINAMICS SINAMICS G120P dv/dt filter compact plus Voltage Peak Limiter Safety information 1 General 2

dv/dt filter compact plus Voltage Peak Limiter SINAMICS SINAMICS G120P dv/dt filter compact plus Voltage Peak Limiter Safety information 1 General 2 dv/dt filter compact plus Voltage Peak Limiter SINAMICS SINAMICS G120P dv/dt filter compact plus Voltage Peak Limiter Operating Instructions Safety information 1 General 2 Mechanical installation 3 Electrical

More information

MCD 200 MCD 500. Remove the Profibus Module using the following procedure: 1. Remove power from the module.

MCD 200 MCD 500. Remove the Profibus Module using the following procedure: 1. Remove power from the module. Installation INSTALLATION INSTRUCTIONS: MCD PROFIBUS MODULE Order Code: 175G9001 1. Installation 1. Remove control power and mains supply from the soft starter. 2. Attach the module to the soft starter

More information

SMVector Additional I/O Module Installation and Operation Manual

SMVector Additional I/O Module Installation and Operation Manual SMVector Additional I/O Module Installation and Operation Manual About These Instructions This documentation applies to the optional Additional I/O module for the SMVector inverter and should be used in

More information

Monitoring technique. VARIMETER Voltage relay MK 9064N, MH 9064

Monitoring technique. VARIMETER Voltage relay MK 9064N, MH 9064 Monitoring technique VARIMETER Voltage relay MK 9064N, MH 9064 0269462 Your Advantages Preventive maintenance For better productivity Quicker fault locating Precise and reliable Min-, Max. value or window

More information

PART 1: GENERAL PART 2: PRODUCT. Phone: Fax: Web: -

PART 1: GENERAL PART 2: PRODUCT. Phone: Fax: Web:  - Specification Number: 23 09 33 Product Name: FRENIC-HVAC AC Drives for Variable Torque Fan & Pump Applications (1-125Hp at 208/230Vac, 1-1000Hp at 460Vac, 1-300Hp at 575Vac) PART 1: GENERAL 1.01 SUMMARY

More information

ATV212HD18N4 variable speed drive ATV kW - 25hp - 480V - 3ph - EMC - IP21

ATV212HD18N4 variable speed drive ATV kW - 25hp - 480V - 3ph - EMC - IP21 Characteristics variable speed drive ATV212-18.5kW - 25hp - 480V - 3ph - EMC - IP21 Main Range of product Altivar 212 Product or component type Device short name Product destination Product specific application

More information

MOTOR STARTERS & VARIABLE SPEED DRIVES Variable speed drives

MOTOR STARTERS & VARIABLE SPEED DRIVES Variable speed drives C2000 VFD-CP Series AC Drive Motor power up to 400kW 3ph HVAC drive for variable torque loads Fire mode and bypass functions Sensorless vector control Features for building automation applications including

More information

50% Energy costs savings. A compact and competitive solution for applications with basic needs.

50% Energy costs savings. A compact and competitive solution for applications with basic needs. Selection Guide VLT HVAC Basic Drive FC 101 A compact and competitive solution for applications with basic needs 50% Energy costs savings Typically, a 20% reduction in speed will yield 50% energy savings

More information

ATS22D75S6 soft starter-ats22-control 220V-power 230V(18.5kW)/ V(37kW)/500V(45kW)

ATS22D75S6 soft starter-ats22-control 220V-power 230V(18.5kW)/ V(37kW)/500V(45kW) Characteristics soft starter-ats22-control 220V-power 230V(18.5kW)/400...440V(37kW)/500V(45kW) Price* : 683.00 GBP Main Range of product Altistart 22 Product or component type Product destination Product

More information

ATV71QC16N4 variable speed drive ATV71Q - 160kW / 250HP V - IP20

ATV71QC16N4 variable speed drive ATV71Q - 160kW / 250HP V - IP20 Characteristics variable speed drive ATV71Q - 160kW / 250HP - 380...480V - IP20 Main Range of product Product or component type Device short name Product destination Product specific application Assembly

More information

1. Safety Danger Warnings Earthing and earth fault protection... 4

1. Safety Danger Warnings Earthing and earth fault protection... 4 vacon 1 INDEX Document: DPD00386A Version release date: 24.9.10 1. Safety... 2 1.1 Danger... 2 1.2 Warnings... 3 1.3 Earthing and earth fault protection... 4 2. Metasys N2 - general info... 5 3. N2 technical

More information

RAD-DI8-IFS. I/O extension module with 8 digital inputs or 2 pulse inputs. INTERFACE Data sheet. 1 Description

RAD-DI8-IFS. I/O extension module with 8 digital inputs or 2 pulse inputs. INTERFACE Data sheet. 1 Description I/O extension module with 8 digital inputs or 2 pulse inputs INTERFACE Data sheet 0483_en_00 PHOENIX CONTACT 203-04-05 Description The I/O extension module can be used in conjunction with Radioline wireless

More information

Optidrive Applications Support Library

Optidrive Applications Support Library Optidrive Applications Support Library Application Note Title AN-ODE-3-038 Related Products Optidrive E3 Overview Level 3 Modbus RTU Control and Register Mapping 1 Fundamental - No previous experience

More information

ATV32HU75N4 variable speed drive ATV kw V - 3 phase - with heat sink

ATV32HU75N4 variable speed drive ATV kw V - 3 phase - with heat sink Characteristics variable speed drive ATV32-7.5 kw - 400 V - 3 phase - with heat sink Main Range of product Altivar 32 Product or component type Product destination Product specific application Function

More information

MAKING MODERN LIVING POSSIBLE. Quick Guide VLT Micro Drive FC 51

MAKING MODERN LIVING POSSIBLE. Quick Guide VLT Micro Drive FC 51 MAKING MODERN LIVING POSSIBLE Quick Guide VLT Micro Drive FC 5 Quick Guide for VLT Micro FC 5 Quick Guide Quick Guide. Safety.. Warnings High Voltage Warning: The voltage of the adjustable frequency drive

More information

SED2 Variable Frequency Drives

SED2 Variable Frequency Drives SED2 Variable Frequency Drives Startup Procedure and Checklist Document No. 155-718 Table of Contents Prerequisites...1 Preparing for SED2 VFD Startup...1 HVAC Startup Procedure for SED2 with Bypass Option...4

More information

ATS22D62Q soft starter-ats22-control 220V-power 230V(15kW)/ V(30kW)

ATS22D62Q soft starter-ats22-control 220V-power 230V(15kW)/ V(30kW) Characteristics soft starter-ats22-control 220V-power 230V(15kW)/400...440V(30kW) Main Range of product Altistart 22 Product or component type Product destination Product specific application Component

More information

Unidrive M200, M201 (Frame 1 to 4) Quick Start Guide

Unidrive M200, M201 (Frame 1 to 4) Quick Start Guide This guide is intended to provide basic information required in order to set-up a drive to run a motor. Please refer to the Unidrive M200 / M20 User Guide which is available to download from www.controltechniques.com/user

More information