UL TEST REPORT AND PROCEDURE

Transcription

1 Issue Date: Page 1 of 14 Report Reference # E A54-UL UL TEST REPORT AND PROCEDURE Standard: Certification Type: CCN: UL , nd Edition, (Information Technology Equipment - Safety - Part 1: General Requirements) CSA C. No , nd Edition, (Information Technology Equipment - Safety - Part 1: General Requirements) Power Supplies for Information Technology Equipment Including Electrical Business Equipment QQGQ, QQGQ7 Product: Switching Power Supply Model: BP*00*03***, BP*00*05***, BP*00*06***, BP*00*07***, BP*00*09***, BP*00*1***, BP*00*14***, BP*00*15***, BP*00*18***, BP*00*4***, BP*00*48***, *ENB100*03*****, *ENB100*05*****, *ENB100*06*****, *ENB100*07*****, *ENB100*09*****, *ENB100*1*****, *ENB100*14*****, *ENB100*15*****, *ENB100*18*****, *ENB100*4*****, *ENB100*48***** (Where * may be alphanumeric, "for marketing purpose and no impact safety related critical components and constructions") Rating: Rated Input; Vac, 50-60Hz, 0.5A Rated Output; 3.3Vdc, 3.0A or 5Vdc, 3.0A or 6Vdc,.5A or 7.5Vdc,.0A or 9Vdc,.0A or 1Vdc, 1.5A or 14Vdc, 1.A or 15Vdc, 1.A or 18Vdc, 1.0A or 4Vdc, 0.75A or 48Vdc, 0.35 or 0.4A Applicant Name and Address: BRIDGEPOWER CORP 964 GOSAEK-DONG GWONSEON-GU SUWON-SI GYEONGGI-DO KOREA Copyright 010

2 Issue Date: Page of 14 Report Reference # E A54-UL This is to certify that representative samples of the products covered by this Test Report have been investigated in accordance with the above referenced Standards. The products have been found to comply with the requirements covering the category and the products are judged to be eligible for Follow-Up Service under the indicated Test Procedure. The manufacturer is authorized to use the UL Mark on such products which comply with this Test Report and any other applicable requirements of Underwriters Laboratories Inc. ('UL') in accordance with the Follow-Up Service Agreement. Only those products which properly bear the UL Mark are considered as being covered by UL's Follow-Up Service under the indicated Test Procedure. The applicant is authorized to reproduce the referenced Test Report provided it is reproduced in its entirety. Any information and documentation involving UL Mark services are provided on behalf of Underwriters Laboratories Inc. (UL) or any authorized licensee of UL. Prepared by: In-Young Hwang Underwriters Laboratories Inc. Reviewed by: HackSoo Song Underwriters Laboratories Inc. Copyright 010

3 Issue Date: Page 3 of 14 Report Reference # E A54-UL Supporting Documentation The following documents located at the beginning of this Procedure supplement the requirements of this Test Report: A. Authorization - The Authorization page may include additional Factory Identification Code markings. B. Generic Inspection Instructions - i. Part AC details important information which may be applicable to products covered by this Procedure. Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of this Test Report. ii. Part AE details any requirements which may be applicable to all products covered by this Procedure. Products described in this Test Report must comply with any applicable items listed unless otherwise stated in the body of each Test Report. iii. Part AF details the requirements for the UL Certification Mark which is not controlled by the technical standard used to investigate these products. Products are permitted to bear only the Certification Mark(s) corresponding to the countries for which it is certified, as indicated in each Test Report. Product Description Switching Mode Power Supply(AC/DC adaptor), consists of electronic components mounted on PWB, a switching transformer and electronic components mounted on PWB, housed with a plastic enclosure. Model Differences BP * 00 * ** * ** (1) () (3)(4)(5) (1). Family Related Designs * is A-Z (). Output * is S (S=Single) (3). Output Voltage 03, 05, 06, 07, 09, 1, 14, 15, 18, 4, 48 (4). Standard Input Cord Options can be F or or Q or N or B or H or G or M or C for input plug type. Photographs for each plug-type configuration F : (Class I = IEC30-C14) Q: (Class II = IEC30-C18) N: ((Class II = IEC30-C8) B or C Class I & Class II - direct-plug-in for North America, China, Japan, Argentina, Changeable Directplug-in type, H- Class I & Class II direct-plug-in for Australia(AS/NZS 311) G- Class I & Class II direct-plug-in for British(BS 1364) M- Class I & Class II direct-plug-in for European(CEE /16)] & Korea (5). Custom Options (Marking, Cord etc.) Number : 00 thru 99 * ENB100 * ** ** * * * (a) (b) (c) (d) (e) (f) (a) Family Related Designs * is A-Z (b) Design Revision Changes A to Z (Standard)

4 Issue Date: Page 4 of 14 Report Reference # E A54-UL (c) Output Voltage 03, 05, 06, 07, 09, 1, 14, 15, 18, 4, 48 (d) Standards Output Cord Options Number : 00 thru 99 (e) Standard Input Cord Options can be F or Q or N or B or H or G or M or C for input plug type. Photographs for each plug-type configuration F : (Class I = IEC30-C14) Q: (Class II = IEC30-C18) N: ((Class II = IEC30-C8) B or C Class I & Class II - direct-plug-in for North America, China, Japan, Argentina, Changeable Directplug-in type, H- Class I & Class II direct-plug-in for Australia(AS/NZS 311) G- Class I & Class II direct-plug-in for British(BS 1364) M- Class I & Class II direct-plug-in for European(CEE /16)] & Korea (f) Custom Options (Marking, Cord etc.) Number : 00 thru 99 Technical Considerations Equipment mobility : movable Connection to the mains : pluggable A Operating condition : continuous Access location : Over voltage category (OVC) : OVC II Mains supply tolerance (%) or absolute mains supply values : +10%, -10% Tested for IT power systems : No IT testing, phase-phase voltage (V) : Class of equipment : Class I (earthed) or Class II (double insulated) Considered current rating (A) : 0.5 Pollution degree (PD) : PD IP protection class : IP X0 Altitude of operation (m) : Up to 000m Altitude of test laboratory (m) :

5 Issue Date: Page 5 of 14 Report Reference # E A54-UL Mass of equipment (kg) : 150g The product was submitted and evaluated for use at the maximum ambient temperature (Tma) permitted by the manufacturer s specification of: 40 C The means of connection to the mains supply is: Detachable power cord, Pluggable A The product is intended for use on the following power systems: TN The equipment disconnect device is considered to be: Appliance inlet or Direct Plug In The following circuit locations (with circuit/schematic designation) were investigated as a limited power source (LPS): All outputs Additional Information Original, 10CA Max. Normal Load Condition: Rated output current Markings and instructions Clause Title Power rating - Ratings Marking or Instruction Details Ratings (voltage, frequency/dc, current) Power rating - Company identification Listee's or Recognized company's name, Trade Name, Trademark or File Number Model Power rating - Model Number Power rating - Class II symbol Symbol for Class II construction ( IEC-517) Special Instructions to UL Representative Inspect the transformer(s) listed in BD1.1 per AA 1.1-(C). When the tests are conducted at otherlocation, inspect test record and specification sheet provided by the component manufacturer.verify the specification sheet indicates 100% routine test specified in BD 1.1 be conducted at thecomponent manufacturer.

6 Issue Date: Page 6 of 14 Report Reference # E A54-UL Production-Line Testing Requirements Electric Strength Test Special Constructions - Refer to Generic Inspection Instructions, Part AC for further information. Model BPI*00***** * Component Transformer(T1 ) Removable Parts Test probe location V rms Primary to Secondary 300 0Va c V dc Test Time, s 1S Earthing Continuity Test Exemptions - This test is not required for the following models: Electric Strength Test Exemptions - This test is not required for the following models: Electric Strength Test Component Exemptions - The following solid-state components may disconnected from the remainder of the circuitry during the performance of this test: Sample and Test Specifics for Follow-Up Tests at UL Model Component Material Test Sample(s) Test Specifics

7 Issue Date: Page 7 of 14 Report Reference # E A54-UL TABLE: List of Critical Components Object/part No. Manufacturer/ trademark type/model technical data CCN Marks of Conformity Enclosure Cheil Industries HN-1064(+) Overall Sized approx 84.5 by46.5 by 3mm & 113 QMFZ UL by 48 by 33.5mm.Min.0 mm thickness, V-0. A Recognized Fabricated Part by 'QMMY' Manufacturer. Appliance Inlet-Class I Rong Feng Industrial SS-10 Min.10A, 50V AXUT UL Appliance Inlet Class II Rong Feng Industrial RF-180 Min..5A, 50V AXUT UL Fuse (F1, F) Wickmann-Werke GMBH 39 Rated 50V, 3.15A. Marked as "50V, T3.15AL" on PWB. JDYX UL Fuse (F1, F) - Alternate Save Fusetech Inc. SS-5 Rated 50V, 3.15A. Marked as "50V, T3.15AL" on JDYX UL PWB. Fuse (F1, F) - Alternate Hollyland 5ET Rated 50V, 3.15A. Marked as "50V, T3.15AL" on PWB. JDYX UL Varistor (ZNR4) Success Electronics SVR14D471K Rated Min. 470 V, (line-to-line), Overall dimension VZCA/8 USR/CNR (Optional) Min.14 mm. Varistor (ZNR4) AMOTECH CO LTD INR14D471 Rated Min. 470 V, (line-to-line), Overall dimension VZCA USR (Optional) - Alternate Min.14 mm. Thermister (TH1) Various Various NTC, 5ohm at 5 C. - - X-capacitor (CX1) (Line Carli MPX 50V, max.0.1 uf. Marked with X1 or X. Meets FOWX UL to Line) IEC X-capacitor (CX1) (Line to Line) - Alternate Pilkor PCX 335M or PCX V, max.0.1 uf. Marked with X1 or X. Meets IEC FOWX UL (E10045) X-capacitor (CX1) (Line to Line) - Alternate Sunil 436D 50V, max.0.1 uf. Marked with X1 or X. Meets IEC FOWX, FOWX8 UL (E145156) X-capacitor (CX1) (Line to Line) - Alternate Tenta MEX 50V, max.0.1 uf. Marked with X1 or X. Meets IEC FOWX, FOWX8 UL (E165646) Discharge resistor (PR1, Various Various Min.1/8W, 510Kohm. - - PR) Discharge resistor (PR1, PR)-4V & 48V only Various Various Min.1/8W, 1.5Mohm. - - Line Filter (LF1) Bridgepower Corp or Wendeng Jeil Electronics Co Ltd Core: Ferrite, Coils: Polyurethane wire min130 C. Bobbin: (QMFZ), Hexian Specialty Chemicals, type PM980@, V-0, 150 C. See Enclosure for details. - Tested in equipment Y-Capacitors (CY1) Success Electronics SE 50V, max.1000 pf. Marked with Y1. Meets FOWX UL

8 Issue Date: Page 8 of 14 Report Reference # E A54-UL Object/part No. Y-Capacitors (CY1) - Alternate Y-Capacitors (CY1) - Alternate Y-Capacitors (CY1) - Alternate Y-Capacitors (CY1) - Alternate Y-Capacitors (CY1) - Alternate Y-Capacitors (CY1, CY) - Alternate Y-Capacitors (CY1, CY) - Alternate Y-Capacitors (CY1, CY) - Alternate Y-Capacitors (CY1, CY) - Alternate Y-Capacitors (CY1, CY) - Alternate Y-Capacitors (CY1, CY) - Alternate Manufacturer/ trademark type/model technical data CCN Marks of Conformity IEC TDK Corp. CD 50V, max.1000 pf. Marked with Y1. Meets IEC Dongil DA 50V, max.1000 pf. Marked with Y1. Meets IEC Netron tech AA 50V, max.1000 pf. Marked with Y1. Meets IEC Samwha Capacitor SD 50V, max.1000 pf. Marked with Y1. Meets IEC KUNSHANTONGFE CT7 50V, max.1000 pf. Marked with Y1. Meets NGELECTRONICSC IEC O LTD Success Electronics SE or SB 50V, max.1000 pf. Marked with Y1 or Y. Meets IEC TDK Corp. CD or CS 50V, max.1000 pf. Marked with Y1 or Y. Meets IEC Dongil DA or DS 50V, max.1000 pf. Marked with Y1 or Y. Meets IEC Netron tech AA or AD 50V, max.1000 pf. Marked with Y1 or Y. Meets IEC Samwha Capacitor SD, SC 50V, max.1000 pf. Marked with Y1 or Y. Meets IEC KUNSHANTONGFE NGELECTRONICSC O LTD CT7 50V, max.1000 pf. Marked with Y1 or Y. Meets IEC FOWX FOWX FOWX FOWX/8 FOWX FOWX FOWX FOWX FOWX FOWX FOWX Bridge Resistor (R3) Various Various 1/4W, 10MOhm - Tested in equipment Bridge Resistor (R3, R4) - Alternate Various Various 1/4W, 4.7MOhm - Tested in equipment Bridge diode (BD1) Various Various Min 600V, max. 0.8A. - Tested in equipment Electrolytic Capacitor (C1, C) Various Various Rated 400 V or 450V, max. uf, min. 105 C. - Tested in equipment Switching IC (U1) Various Various Max30V, Max4mA. - Tested in equipment UL UL UL UL UL UL UL UL UL UL UL

9 Issue Date: Page 9 of 14 Report Reference # E A54-UL Object/part No. Manufacturer/ trademark type/model technical data CCN Marks of Conformity FET (Q1) Various Various Max 650 V, 4.A. Secured to HS1 by a screw. - Tested in equipment Main Transformer (T1) for 3.3V output Bridgepower Corp JEC(B) (Part No.: ) Class B: R/C (OBJY), Class 130(B) Insulation System, BridgePower Corp, Designated JEC(B)Winding: R/C (OBJT), Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX- ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. - Tested in equipment Main Transformer (T1) for 5 V & 6 Voutput Main Transformer (T1) for 7.5 V & 9 Voutput Main Transformer (T1) for 1 Voutput Main Transformer (T1) for 14 V & 15 V output Bridgepower Corp Bridgepower Corp or Wendeng Jeil Electronics Co Ltd Bridgepower Corp Bridgepower Corp JEC(B) (Part No.: ) JEC(B) (Part No.: ) JEC(B) (Part No.: ) JEC(B) (Part No.: ) Class B: R/C (OBJY), Class 130(B) Insulation System, BridgePower Corp, Designated JEC(B)Winding: R/C (OBJT), Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX- ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. Class B: R/C (OBJY), Class 130(B) Insulation System, BridgePower Corp, Designated JEC(B)Winding: R/C (OBJT), Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX- ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. Class B: R/C (OBJY), Class 130(B) Insulation System, BridgePower Corp, Designated JEC(B)Winding: R/C (OBJT), Polyurethanewire Min. 130deg C.Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX-ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. Class B: R/C (OBJY), Class 130(B) Insulation System, BridgePower Corp, Designated JEC(B)Winding: R/C (OBJT), Polyurethanewire Min. 130deg C.Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX-ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. - Tested in equipment - UL - UL - UL

10 Issue Date: Page 10 of 14 Report Reference # E A54-UL Object/part No. Main Transformer (T1) for 18 V output Main Transformer (T1) for 4 V output Main Transformer (T1) for 48 V output Optical Isolator (U) Optical Isolator (U)- Alternate Optical Isolator (U)- Alternate Optical Isolator (U)- - Alternate Manufacturer/ trademark type/model technical data CCN Marks of Conformity 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. Bridgepower Corp or JEC(B) (Part No.: Class B: R/C (OBJY), Class 130(B) Insulation Wendeng Jeil ) System, BridgePower Corp, Designated Electronics Co Ltd JEC(B)Winding: R/C (OBJT), Polyurethanewire Min. 130deg C.Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX-ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. Bridgepower Corp JEC(B) (Part No.: Class B: R/C (OBJY), Class 130(B) Insulation ) System, BridgePower Corp, Designated JEC(B)Winding: R/C (OBJT), Polyurethanewire Min. 130deg C.Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX-ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. Bridgepower Corp JEC(B) (Part No.: Class B: R/C (OBJY), Class 130(B) Insulation ) System, BridgePower Corp, Designated JEC(B)Winding: R/C (OBJT), Polyurethanewire Min. 130deg C.Triple Insulated Wire, 130 deg C, Furukawa Electric, Cat. No: TEX-ECore: Ferrite, size 5 by 19mm. Coils: Polyurethane wire Min. 130 deg C. Bobbin: (QMFZ), V-0, 130 deg C. Vishay TCET1103(G) Double protection optical isolator. Providing Semiconductor isolation voltage 5000 Vac. External dcr min. 8.0 mm. COSMO KP1010 Double protection optical isolator. Providing ELECTRONICS isolation voltage 5000 Vac. External dcr min. 8.0 CORP mm. Sharp Corp PC13 Double protection optical isolator. Providing isolation voltage 5000 Vac. KODENSHI KOREA PC-17KPC- Double protection optical isolator. Providing 17K1C isolation voltage 5000 Vac. External dcr min. 8.0 mm. - UL - UL - UL FPQU/8 FPQU/8 FPQU/8 FPQU/8 Heatsink(HS1)(For Q1) Various Various Overall Sized Min. ø 18by 0 mm, Min.1.5 mm - -- thick Heatsink(HS)(For D3) Various Various Overall Sized Min. ø 0by 1 mm, Min.1.5 mm - -- UL UL UL UL

11 Issue Date: Page 11 of 14 Report Reference # E A54-UL Object/part No. Manufacturer/ trademark type/model technical data CCN Marks of Conformity thick Insulation Various Various Overall Sized Min. ø 31by 0 mm, Min.0.4 mm - -- Sheet(Between T1 & U) thick PWB Various Various Min. V-1, 130 C. ZPMV UL Output Cable Various Various For use of external interconnection,max 3.05 m AVLV UL long,max. 300 V, 80 C, min.0 AWG,Marked with VW-1 or FT-1.Style no. 464 or 1777 Output Cable_alternate Various Various For use of external interconnection, Style No. 464 AVLV UL or 1777, min. 300 V, 80 C, 18 AWG, VW-1, FT-1. Max m long Bonding Glue Various Various Min. V-, min. 100 C for additional secureness of QMFZ UL internal conductor. Nameplate Label Various Various Suitable for use on surface of Polycarbonate (PC) with max.80 C surface temperature PGDQ, PGJI UL

12 Issue Date: Page 1 of 14 Report Reference # E A54-UL Enclosures Type Supplement Id Description Photographs 3-09 External View for B type (Class I) Photographs 3-11 External View for B type (Class II) Photographs 3-13 External View F type (Class I) Photographs 3-14 External View G type (Class I) Photographs 3-15 External View G type (Class II) Photographs 3-16 External View H type (Class I) Photographs 3-17 External View H type (Class II) Photographs 3-3 External View N type (Class II) Photographs 3-4 External View Q type (Class II) Photographs 3-7 Internal View_Bottom Photographs 3-8 Internal View_Top Photographs 3-34 External View POE type Photographs 3-35 Interal View_Top_POE A type Photographs 3-36 Internal View_TOP POE B type Photographs 3-37 Internal View Bottom _POE B type Photographs 3-38 Internal View Bottom_POE A type Diagrams 4-01 Schematic_ClassI Schematics + PWB 5-01 Schematic_ClassII Schematics + PWB 5-0 Schematic_POE type Schematics + PWB 5-03 PCB Pattern Schematics + PWB 5-04 PCB Pattern_POE_BP*00*48** AB type Schematics + PWB 5-05 PCB Pattern _ POE_BP*00*48** Ctype Manuals Miscellaneous 7-04 Transformer (T1)_ Miscellaneous 7-05 Transformer (T1)_ Miscellaneous 7-06 Transformer (T1)_ Miscellaneous 7-07 Transformer (T1)_ Miscellaneous 7-08 Transformer (T1)_ Miscellaneous 7-09 Transformer (T1)_ Miscellaneous 7-10 Transformer (T1)_ Miscellaneous 7-1 Drawing AC Plug Miscellaneous 7-15 LineFillter_Spec Miscellaneous 7-17 Transformer(T1)_

13 Issue Date: Page 13 of 14 Report Reference # E A54-UL Miscellaneous 7-18 Label_BP*00*03***_ClassI Miscellaneous 7-19 Label_BP*00*03***_ClassII Miscellaneous 7-0 Label_BP*00*05***_ClassII Miscellaneous 7-1 Label_BP*00*05***_ClassI Miscellaneous 7- Label_BP*00*06***_ClassI Miscellaneous 7-3 Label_BP*00*06***_ClassII Miscellaneous 7-4 Label_BP*00*07***_ClassI Miscellaneous 7-5 Label_BP*00*07***_ClassII Miscellaneous 7-6 Label_BP*00*09***_ClassI Miscellaneous 7-7 Label_BP*00*09***_ClassII Miscellaneous 7-8 Label_BP*00*1***_ClassI Miscellaneous 7-9 Label_BP*00*1***_ClassII Miscellaneous 7-30 Label_BP*00*14***_ClassI Miscellaneous 7-31 Label_BP*00*14***_ClassII Miscellaneous 7-3 Label_BP*00*15***_ClassI Miscellaneous 7-33 Label_BP*00*15***_ClassII Miscellaneous 7-34 Label_BP*00*18***_ClassI Miscellaneous 7-35 Label_BP*00*18***_ClassII Miscellaneous 7-36 Label_BP*00*4***_ClassI Miscellaneous 7-37 Label_BP*00*4***_ClassII Miscellaneous 7-38 Label_BP*00*48***_ClassI Miscellaneous 7-39 Label_BP*00*48***_ClassII Miscellaneous 7-40 Label_BP*00*48***_0.35A_ClassI Miscellaneous 7-41 Label_BP*00*48***_0.35A_ClassII Miscellaneous 7-4 Label_*ENB100*03*****_ClassI Miscellaneous 7-43 Label_*ENB100*03*****_ClassII Miscellaneous 7-44 Label_*ENB100*05*****_ClassI Miscellaneous 7-45 Label_*ENB100*05*****_ClassII Miscellaneous 7-46 Label_*ENB100*06*****_ClassI Miscellaneous 7-47 Label_*ENB100*06*****_ClassII Miscellaneous 7-48 Label_*ENB100*07*****_ClassI Miscellaneous 7-49 Label_*ENB100*07*****_ClassII Miscellaneous 7-50 Label_*ENB100*09*****_ClassI Miscellaneous 7-51 Label_*ENB100*09*****_ClassII Miscellaneous 7-5 Label_*ENB100*1*****_ClassI Miscellaneous 7-53 Label_*ENB100*1*****_ClassII Miscellaneous 7-54 Label_*ENB100*14*****_ClassI

14 Issue Date: Page 14 of 14 Report Reference # E A54-UL Miscellaneous 7-55 Label_*ENB100*14*****_ClassII Miscellaneous 7-56 Label_*ENB100*15*****_ClassI Miscellaneous 7-57 Label_*ENB100*15*****_ClassII Miscellaneous 7-58 Label_*ENB100*18*****_ClassI Miscellaneous 7-59 Label_*ENB100*18*****_ClassII Miscellaneous 7-60 Label_*ENB100*4*****_ClassI Miscellaneous 7-61 Label_*ENB100*4*****_ClassII Miscellaneous 7-6 Label_*ENB100*48*****_ClassI Miscellaneous 7-63 Label_*ENB100*48*****_ClassII Miscellaneous 7-64 Label_*ENB100*48*****_0.35A_ClassI Miscellaneous 7-65 Label_*ENB100*48*****_0.35A_ClassII

15 Issue Date: Page 1 of 6 Report Reference # E A54-UL 1 GENERAL 1.5 Components General Comply with or relevant component standard 1.5. Evaluation and testing of components Components certified to IEC harmonized standard and checked for correct application. Components, for which no relevant IEC-Standard exist, have been tested under the conditions occurring in the equipment, using applicable parts of. Components not certified are used in accordance with their ratings and they comply with applicable parts of IEC and the relevant component Standard Thermal controls Transformers (see Annex C) Interconnecting cables Interconnecting cables comply with the relevant requirements of this standard Capacitors bridging insulation Between lines; X1 or X capacitor according to IEC ;1993. Between Primary-to-earth capacitors: Y1 according to IEC :1993. Between Primary-to-secondary capacitors: Y1 according to IEC : Resistors bridging insulation Resistors bridging functional, basic or supplementary insulation Resistors bridging double or reinforced insulation between a.c. mains and other circuits Resistors bridging double or reinforced insulation between a.c. mains and antenna or coaxial cable Components in equipment for IT power systems

16 Issue Date: Page of 6 Report Reference # E A54-UL Surge suppressors General Protection of VDRs Bridging of functional insulation by a VDR IEC and UL 1449 certified VDR used. (see appended table 1.5.1) Bridging of basic insulation by a VDR Bridging of supplementary, double or reinforced insulation by a VDR 1.6 Power interface AC power distribution systems AC power distribution systems are classified as TN Input current (see appended table 1.6.) Voltage limit of hand-held equipment Neutral conductor Neutral is insulated from earth with basic insulation for Class I equipment. 1.7 Marking and instructions Power rating Rated voltage(s) or voltage range(s) (V)... : Vac Symbol for nature of supply, for d.c. only... : Rated frequency or rated frequency range (Hz)... : Hz Rated current (ma or A)... : Refer to the Rating information at the beginning of this Test Report. Manufacturer's name or trademark or identification mark... : Bridgepower Corp. or E Model identification or type reference... : Refer to the Model information at the beginning of this Test Report. Symbol for Class II equipment only... : IEC-517 symbol marked on Class II equipment Other markings and symbols... : Additional symbols or marking does not give rise to misunderstanding Safety instructions and marking General

17 Issue Date: Page 3 of 6 Report Reference # E A54-UL Disconnect devices Overcurrent protective device IT Power distribution systems Operator access with a tool Ozone Short duty cycles Equipment is designed for continuous operation Supply voltage adjustment... : Equipment is auto-ranging. Method and means of adjustment; reference to installation instructions... : Power outlets on the equipment... : No standard power outlets are provided Fuse identification (marking, special fusing characteristics, cross-reference)... : Fuse, F1, F provided with an unambiguous cross-reference. (F is only optional component) Wiring terminals Protective earthing and bonding terminals... : The earthing terminal is marked with the standard earth symbol ( IEC-5019) near the terminal for Class I equipment Terminals for a.c. mains supply conductors The equipment with appliance inlet, which is intended to use the detachable type power supply cord Terminals for d.c. mains supply conductors Controls and indicators Identification, location and marking... : Colours... : Symbols according to IEC : Markings using figures... : Isolation of multiple power sources... : Thermostats and other regulating devices... : Durability All markings provided on UL Recognized component labels suitable for surface they are

18 Issue Date: Page 4 of 6 Report Reference # E A54-UL applied upon Removable parts Replaceable batteries... : No batteries provided. Language(s)... : Equipment for restricted access locations... : The equipment is not intended for installation in a Restricted Access Area. PROTECTION FROM HAZARDS.1 Protection from electric shock and energy hazards.1.1 Protection in operator access areas Access to energized parts Test by inspection... : No access with test finger and test pin to any parts with only basic insulation to ELV or hazardous voltage. Any hazardous parts accessible are unlikely. Test with test finger (Figure A)... : The test finger was unable to contact bare hazardous parts, basic insulation, or ELV circuits. Test with test pin (Figure B)... : The test pin was unable to contact bare hazardous parts. Test with test probe (Figure C)... : No TNV present Battery compartments Access to ELV wiring Working voltage (Vpeak or Vrms); minimum - distance through insulation (mm)... : Access to hazardous voltage circuit wiring Energy hazards... : No energy hazard in operator area Manual controls Discharge of capacitors in equipment Measured voltage (V); time-constant (s)... : Vo; 375Vpk, 37% Vo; 139Vpk, Vtc;0Vdc -

19 Issue Date: Page 5 of 6 Report Reference # E A54-UL Energy hazards - d.c. mains supply a) Capacitor connected to the d.c. mains supply.. : b) Internal battery connected to the mains supply : Audio amplifiers... :.1. Protection in service access areas.1.3 Protection in restricted access locations. SELV circuits..1 General requirements.. Voltages under normal conditions (V)... : All accessible voltages are less than 4.4 Vp or 60 V dc and are classified as SELV...3 Voltages under fault conditions (V)... : Under fault conditions voltages never exceed 71V peak and 10Vdc and do not exceed 4.4V peak or 60V dc for more than 0. sec...4 Connection of SELV circuits to other circuits... : SELV circuits are only connected to other secondary circuits. SELV circuit and all interconnected circuits separated from primary by reinforced insulation. The SELV circuit does not exceed the SELV limits under normal and fault conditions..3 TNV circuits.3.1 Limits Type of TNV circuits... : Separation from other circuits and from accessible parts.3..1 General requirements.3.. Protection by basic insulation.3..3 Protection by earthing.3..4 Protection by other constructions... :.3.3 Separation from hazardous voltages Insulation employed... : Connection of TNV circuits to other circuits

20 Issue Date: Page 6 of 6 Report Reference # E A54-UL Insulation employed... : Test for operating voltages generated externally.4 Limited current circuits.4.1 General requirements.4. Limit values 0.5 ma rms (0.7 ma pk) Frequency (Hz)... : Annex D meter method - Measured current (ma)... : 0.087mA rms - Measured voltage (V)... : Annex D meter method - Measured circuit capacitance (nf or uf)... : Less than 0.1 uf Connection of limited current circuits to other circuits.5 Limited power sources a) Inherently limited output b) Impedance limited output c) Regulating network limited output under normal operating and single fault condition d) Overcurrent protective device limited output Max. output voltage (V), max. output current (A), max. apparent power (VA)... : For 3.3Vdc output Normal Uoc; 3.559Vdc, Isc5s; 4.15A, VA5s; 1.5VA SR5 short condition Uoc;4.5Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;7.0Vpk, Isc5s; 0, VA5s; 0 - For 5Vdc output Normal Uoc; 5.01Vdc, Isc5s; 4.09A, VA5s; 19.15VA SR5 short condition Uoc;6.5Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;10.8Vpk, Isc5s; 0, VA5s; 0 For 6Vdc output Normal Uoc; 6.191Vdc, Isc5s; 3.3A,

21 Issue Date: Page 7 of 6 Report Reference # E A54-UL VA5s; 18.4VA SR5 short condition Uoc;7.6Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;1.1Vpk, Isc5s; 0, VA5s; 0 For 7.5Vdc output Normal Uoc; 7.739Vdc, Isc5s;.87A, VA5s; 80.87VA SR5 short condition Uoc;9.0Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;13.Vpk, Isc5s; 0, VA5s; 0 For 9Vdc output Normal Uoc; 9.365Vdc, Isc5s;.77A, VA5s; 4.9VA SR5 short condition Uoc;8.8Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;.0Vpk, Isc5s; 0, VA5s; 0 For 1Vdc output Normal Uoc; 1.159Vdc, Isc5s;.38A, VA5s; 7.95VA SR5 short condition Uoc;9.0Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;18.5Vpk, Isc5s; 0, VA5s; 0 For 14Vdc output Normal Uoc; Vdc, Isc5s;.147A, VA5s; 8.3VA SR5 short condition Uoc;8.8Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;.0Vpk, Isc5s; 0, VA5s; 0 For 15Vdc output Normal Uoc; 15.19Vdc, Isc5s; 3.0A, VA5s; 9.4VA SR5 short condition Uoc;9Vpk, Isc5s;0, VA5s;0

22 Issue Date: Page 8 of 6 Report Reference # E A54-UL SR5 open condition Uoc;0, Isc60s; 0, VA60s; 0 For 18Vdc output Normal Uoc; Vdc, Isc5s; 1.83A, VA5s; 9.5VA SR5 short condition Uoc;9.4Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;7.4Vpk, Isc5s; 0, VA5s; 0 For 4Vdc output Normal Uoc; 4.18Vdc, Isc5s; 1.547A, VA5s; 36.1VA SR5 short condition Uoc;1.56Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;44.Vpk, Isc5s; 0, VA5s; 0 For 48Vdc output Normal Uoc; 47.75Vdc, Isc5s; 0.96A, VA5s; 38.7VA SR5 short condition Uoc;9.6Vpk, Isc5s;0, VA5s;0 SR5 open condition Uoc;8.8Vpk, Isc5s; 0, VA5s; 0 Current rating of overcurrent protective device (A) : Provisions for earthing and bonding.6.1 Protective earthing for Class I equipment.6. Functional earthing.6.3 Protective earthing and protective bonding conductors General.6.3. Size of protective earthing conductors Rated current (A), cross-sectional area (mm²), AWG... : Appliance Inlet used Size of protective bonding conductors Rated current (A), cross-sectional area (mm²), AWG... : 0.5A, 0.75 (mm), 18AWG -

23 Issue Date: Page 9 of 6 Report Reference # E A54-UL Protective current rating (A), cross-sectional area (mm²), AWG... : Resistance of earthing conductors and their terminations; resistance (ohm), voltage drop (V), test current (A), duration (min)... : ohm, 0.63 Vdrop(Appliance inlet GND pin to Molded Ground on PWB), 40 A, minute.(for Class I equipment) Colour of insulation... : Protective bonding conductor is green with yellow stripe.(for Class I equipment).6.4 Terminals General.6.4. Protective earthing and bonding terminals Rated current (A), type, nominal thread diameter (mm)... : Appliance Inlet used Separation of the protective earthing conductor from protective bonding conductors.6.5 Integrity of protective earthing Interconnection of equipment.6.5. Components in protective earthing conductors and protective bonding conductors No switches or fuses in earthing conductors Disconnection of protective earth Disconnection of the protective earth at one assembly removes connection of HAZARDOUS VOLTAGES from the other assemblies at the same time.(for Class I equipment) Parts that can be removed by an operator It is not possible to disconnect earth without disconnecting mains Parts removed during servicing Connections to protective earthing cannot be removed unless hazardous voltage is removed from the part simultaneously Corrosion resistance Screws for protective bonding Reliance on telecommunication network or cable distribution system

24 Issue Date: Page 10 of 6 Report Reference # E A54-UL.7 Overcurrent and earth fault protection in primary circuits.7.1 Basic requirements Instructions when protection relies on building installation.7. Faults not covered in Short-circuit backup protection.7.4 Number and location of protective devices... : Two protective devices used. One for "LIVE" phase, the other for "Neutral" phase (optional)..7.5 Protection by several devices.7.6 Warning to service personnel... : No Service area.8 Safety interlocks.8.1 General principles.8. Protection requirements.8.3 Inadvertent reactivation.8.4 Fail-safe operation.8.5 Moving parts.8.6 Overriding.8.7 Switches and relays Contact gaps (mm)... :.8.7. Overload test Endurance test Electric strength test.8.8 Mechanical actuators.9 Electrical insulation.9.1 Properties of insulating materials Natural rubber, asbestos or hygroscopic material is not used..9. Humidity conditioning Relative humidity (%), temperature ( C)... : 93%, 30 degree C Grade of insulation Insulation materials comply with sub-clauses.10, 4.5 and 5..

25 Issue Date: Page 11 of 6 Report Reference # E A54-UL.9.4 Separation from hazardous voltages Method(s) used... : Method 1 used Clearances, creepage distances and distances through insulation.10.1 General Frequency... : Less than 30 khz Pollution degrees... : Reduced values for functional insulation See clause Intervening unconnected conductive parts Insulation with varying dimensions Special separation requirements Insulation in circuits generating starting pulses.10. Determination of working voltage General.10.. RMS working voltage Peak working voltage.10.3 Clearances See appended table.10.3, General Mains transient voltages Overvoltage Category II ; Mains transient voltage is 500 Vpk. a) AC mains supply... : Less than 300 Vrms. b) Earthed d.c. mains supplies... : c) Unearthed d.c. mains supplies... : d) Battery operation... : Clearances in primary circuits (see appended table.10.3 and.10.4) Clearances in secondary circuits Functional insulation only.(see sub-clause 5.3.4) Clearances in circuits having starting pulses Transients from a.c. mains supply... : See Clause Transients from d.c. mains supply... : Transients from telecommunication networks and cable distribution systems... :

26 Issue Date: Page 1 of 6 Report Reference # E A54-UL Measurement of transient voltage levels a) Transients from a mains supply For an a.c. mains supply... : For a d.c. mains supply... : b) Transients from a telecommunication network.10.4 Creepage distances (see appended table.10.3 and.10.4) General Material group and comparative tracking index CTI tests... : Material group IIIb; 100 <=CTI < Minimum creepage distances (see appended table.10.3 and.10.4).10.5 Solid insulation Solid or laminated insulating materials having adequate thickness are provided and approved optical isolator provided General Distances through insulation (see appended table.10.5) Insulating compound as solid insulation Certified optical isolator used. (see appended table 1.5.1) Semiconductor devices Cemented joints Certified optical isolator used. (see appended table 1.5.1) Thin sheet material - General Two layers used, each of which complies with the required electric strength test Separable thin sheet material Number of layers (pcs)... : minimum two layers Non-separable thin sheet material Thin sheet material - standard test procedure Electric strength test... : Thin sheet material - alternative test procedure Electric strength test... : (see appended table 5.) - -

27 Issue Date: Page 13 of 6 Report Reference # E A54-UL Insulation in wound components Wire in wound components Working voltage... : Triple insulated wire used in T1. a) Basic insulation not under stress... : b) Basic, supplementary, reinforced insulation... : Supplementary or Reinforced. c) Compliance with Annex U... : Wiring meets the requirements of Annex U. Two wires in contact inside wound component; angle between 45 and : Physical separation in the form of insulating sheet material to relieve mechanical stress at the crossover point Wire with solvent-based enamel in wound components Electric strength test... : - - Routine test Additional insulation in wound components Working voltage... : - Basic insulation not under stress... : - Supplementary, reinforced insulation... :.10.6 Construction of printed boards Uncoated printed boards Coated printed boards Insulation between conductors on the same inner surface of a printed board Insulation between conductors on different layers of a printed board Distance through insulation Number of insulation layers (pcs)... :.10.7 Component external terminations.10.8 Tests on coated printed boards and coated components Sample preparation and preliminary inspection Thermal conditioning

28 Issue Date: Page 14 of 6 Report Reference # E A54-UL Electric strength test Abrasion resistance test.10.9 Thermal cycling Test for Pollution Degree 1 environment and insulating compound Tests for semiconductor devices and cemented joints.10.1 Enclosed and sealed parts

29 Issue Date: Page 15 of 6 Report Reference # E A54-UL 3 WIRING, CONNECTIONS AND SUPPLY 3.1 General Current rating and overcurrent protection 3.1. Protection against mechanical damage Wires do not touch sharp edges and heatsink which could damage the insulation and cause hazard Securing of internal wiring Insulation of conductors The insulation of the individual conductors are suitable for the application and the working voltage Beads and ceramic insulators Screws for electrical contact pressure Insulating materials in electrical connections Self-tapping and spaced thread screws Termination of conductors All conductors are reliably secured. 10 N pull test Sleeving on wiring 3. Connection to mains supply 3..1 Means of connection The unit is provided with an appliance inlet or DPIU Connection to an a.c. mains supply Connection to a d.c. mains supply 3.. Multiple supply connections 3..3 Permanently connected equipment Number of conductors, diameter of cable and conduits (mm)... : 3..4 Appliance inlets The appliance inlet complies with IEC 6030 and UL Power supply cords AC power supply cords Type... : - Rated current (A), cross-sectional area (mm²), AWG... : - -

30 Issue Date: Page 16 of 6 Report Reference # E A54-UL DC power supply cords 3..6 Cord anchorages and strain relief Mass of equipment (kg), pull (N)... : - Longitudinal displacement (mm)... : Protection against mechanical damage 3..8 Cord guards Diameter of minor dimension D (mm); test mass (g) -... : Radius of curvature of cord (mm)... : Supply wiring space 3.3 Wiring terminals for connection of external conductors Wiring terminals 3.3. Connection of non-detachable power supply cords Screw terminals Conductor sizes to be connected Rated current (A), cord/cable type, cross-sectional - area (mm²)... : Wiring terminal sizes Rated current (A), type and nominal thread - diameter (mm)... : Wiring terminals design Grouping of wiring terminals Stranded wire 3.4 Disconnection from the mains supply General requirement 3.4. Disconnect devices The equipment is provided with an appliance coupler or DPIU Permanently connected equipment Parts which remain energized No parts remain energized when the disconnect device is removed Switches in flexible cords Number of poles - single-phase and d.c. equipment Disconnect device disconnects

31 Issue Date: Page 17 of 6 Report Reference # E A54-UL all poles simultaneously Number of poles - three-phase equipment Switches as disconnect devices Plugs as disconnect devices Interconnected equipment Multiple power sources 3.5 Interconnection of equipment General requirements 3.5. Types of interconnection circuits... : Interconnection circuit is SELV CIRCUIT ELV circuits as interconnection circuits Data ports for additional equipment

32 Issue Date: Page 18 of 6 Report Reference # E A54-UL 4 PHYSICAL REQUIREMENTS 4.1 Stability Angle of 10 Test force (N)... : 4. Mechanical strength 4..1 General 4.. Steady force test, 10 N 4..3 Steady force test, 30 N 4..4 Steady force test, 50 N 4..5 Impact test Fall test Swing test 4..6 Drop test; height (mm)... : 4..7 Stress relief test No indication of shrinkage or distortion on enclosures due to the stress relief test 80 degree C/7 h Cathode ray tubes Picture tube separately certified... : 4..9 High pressure lamps Wall or ceiling mounted equipment; force (N)... : 4.3 Design and construction Edges and corners 4.3. Handles and manual controls; force (N)... : Adjustable controls Securing of parts No loosening of parts impairing creepage distances or clearances over supplementary or reinforced insulation is likely to occur Connection by plugs and sockets The equipment does not have any interchangeable plugs/sockets Direct plug-in equipment

33 Issue Date: Page 19 of 6 Report Reference # E A54-UL Torque... : - Compliance with the relevant mains plug standard: Heating elements in earthed equipment Batteries - Overcharging of a rechargeable battery - Unintentional charging of a non-rechargeable battery - Reverse charging of a rechargeable battery - Excessive discharging rate for any battery Oil and grease Dust, powders, liquids and gases Containers for liquids or gases Flammable liquids... : Quantity of liquid (l)... : Flash point ( C)... : Radiation General Ionizing radiation Measured radiation (pa/kg)... : - Measured high-voltage (kv)... : - Measured focus voltage (kv)... : - CRT markings... : Effect of ultraviolet (UV) radiation on materials Part, property, retention after test, flammability classification... : Human exposure to ultraviolet (UV) radiation... : Laser (including LEDs) Laser class... : Other types... : 4.4 Protection against hazardous moving parts General

34 Issue Date: Page 0 of 6 Report Reference # E A54-UL 4.4. Protection in operator access areas... : Protection in restricted access locations... : Protection in service access areas 4.5 Thermal requirements General 4.5. Temperature tests (see appended table 4.5) Normal load condition per Annex L... : Rated output current Temperature limits for materials Touch temperature limits Resistance to abnormal heat... : (see appended table 4.5.5) 4.6 Openings in enclosures Top and side openings Dimensions (mm)... : No openings Bottoms of fire enclosures Construction of the bottom, dimensions (mm)... : No openings Doors or covers in fire enclosures Openings in transportable equipment Constructional design measures Dimensions (mm)... : Evaluation measures for larger openings Use of metallized parts Adhesives for constructional purposes Conditioning temperature ( C), time (weeks)... : Resistance to fire Reducing the risk of ignition and spread of flame Method 1 used. Method 1, selection and application of components wiring and materials (see appended table 4.7) Method, application of all of simulated fault condition tests 4.7. Conditions for a fire enclosure Parts requiring a fire enclosure Parts not requiring a fire enclosure

35 Issue Date: Page 1 of 6 Report Reference # E A54-UL Materials General Materials for fire enclosures Equipment is movable with mass less than 18 kg. Fire enclosure material is min. V Materials for components and other parts outside fire enclosures Materials for components and other parts inside fire enclosures All internal materials are rated V- or better or are mounted on a PWB rated V-1 or better Materials for air filter assemblies Materials used in high-voltage components

36 Issue Date: Page of 6 Report Reference # E A54-UL 5 ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS 5.1 Touch current and protective conductor current General 5.1. Configuration of equipment under test (EUT) EUT has only one mains connection Single connection to an a.c. mains supply Redundant multiple connections to an a.c. mains supply Simultaneous multiple connections to an a.c. mains supply Test circuit Application of measuring instrument Tested using D.1 measuring instrument Test procedure Test measurements Supply voltage (V)... : 64 V, 60 Hz - Measured touch current (ma)... : 0.003mA r.m.s. for Class I - equipment; 0.045mAr.m.s. for Class II equipment. Max. allowed touch current (ma)... : 3.5 mar.m.s. for Class I - equipment; 0.5 mar.m.s. for Class II equipment. Measured protective conductor current (ma)... :. - Max. allowed protective conductor current (ma)... : Equipment with touch current exceeding 3,5 ma General... : Simultaneous multiple connections to the supply Touch currents to telecommunication networks and cable distribution systems and from telecommunication networks Limitation of the touch current to a telecommunication network or to a cable distribution system Supply voltage (V)... : - Measured touch current (ma)... : -

37 Issue Date: Page 3 of 6 Report Reference # E A54-UL Max. allowed touch current (ma)... : Summation of touch currents from telecommunication networks a) EUT with earthed telecommunication ports... : b) EUT whose telecommunication ports have no reference to protective earth 5. Electric strength 5..1 General (see appended table 5.) 5.. Test procedure 5.3 Abnormal operating and fault conditions Protection against overload and abnormal operation 5.3. Motors Transformers (see appended Annex C) Functional insulation... : Functional insulation complies with the requirements (a), (b), or (c) Electromechanical components Audio amplifiers in ITE... : Simulation of faults Unattended equipment Compliance criteria for abnormal operating and fault conditions During the tests No fire, emission of molten metal or deformation was noted during the tests After the tests Electric Strength tests performed after abnormal and fault tests. 6 CONNECTION TO TELECOMMUNICATION NETWORKS 7 CONNECTION TO CABLE DISTRIBUTION SYSTEMS

38 Issue Date: Page 4 of 6 Report Reference # E A54-UL A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see and 5.3.) C ANNEX C, TRANSFORMERS (see and 5.3.3) Position... : (see appended table 1.5.1) - Manufacturer... : (see appended table 1.5.1) - Type... : (see appended table 1.5.1) - Rated values... : Class B - Method of protection... : Inherently protection - C.1 Overload test (see appended table 5.3) C. Insulation (see appended table 5.) Protection from displacement of windings... : TIWW used in secondary winding wire. D ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see 5.1.4) D.1 Measuring instrument MD Box used D. Alternative measuring instrument E ANNEX E, TEMPERATURE RISE OF A WINDING (see ) F ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES (see.10 and Annex G) G ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM CLEARANCES H ANNEX H, IONIZING RADIATION (see )

39 Issue Date: Page 5 of 6 Report Reference # E A54-UL J ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see.6.5.6) K ANNEX K, THERMAL CONTROLS (see and 5.3.8) L ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL BUSINESS EQUIPMENT (see and 4.5.) L.1 Typewriters L. Adding machines and cash registers L.3 Erasers L.4 Pencil sharpeners L.5 Duplicators and copy machines L.6 Motor-operated files L.7 Other business equipment AC/DC adapter, Rated output current. M ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see.3.1) N ANNEX N, IMPULSE TEST GENERATORS (see , , , 6...1, 7.3., and Clause G.5) P ANNEX P, NORMATIVE REFERENCES Q ANNEX Q, Voltage dependent resistors (VDRs) (see ) a) Preferred climatic categories... : IEC and UL 1449 certified VDR used. (see appended table 1.5.1) b) Maximum continuous voltage... : Component rating is at least 10 % of the rated voltage of the equipment. c) Pulse current... : IEC and UL 1449 certified VDR used. (see appended table 1.5.1)