Ohm Metrics. Instruction Manual. Dual Footwear Wrist Strap Tester Model PDT800K

Transcription

1 T R A N S F O R M I N G T E C H N O L O G I E S, L L C O U T S T A N D I N G A L T E R N A T I V E S I N S T A T I C C O N T R O L Ohm Metrics Dual Footwear Wrist Strap Tester Model PDT800K Instruction Manual

2 Contents 1 Description PDT800 1 Features 1 Front Panel Controls 2 2 Installation Free Standing Assembly 4 Height Adjustment 5 Wall Mount 5 Change Limits 5 3 Testing Wrist Strap 6 Footwear 6 4 Turnstile/Barrier/Gate System 8 5 Specifications 8 6 Parts Included List 8 7 Service and Warranty 9

3 Description Ohm Metrics Deluxe Combo Wrist Strap and Footwear Tester: Model PDT800 The PDT800 is a comprehensive, accurate tool to fully meet your daily ESD checking needs. Independently tests the left and right foot and wrist band and an innovative LCD screen will instantly display the test result and the measured resistances. The proactive Near-Fail indicator alerts the user that the ESD grounding device under test is nearing failure levels. Meets or exceeds the requirements of international standards such as ANSI/ESD S or IEC Features include: LCD display instantly displays the test result and the measured resistance. Near-Fail LED indicator. Tests both wrist strap and footwear simultaneously or independently. 100% independently test the left-foot and the right-foot. Test limits meet USA and European standards; preset with broad test range 100KΩ~1GΩ. 1

4 Front Control Panel 1. Wrist strap Plug-jack 2. Right Foot LED Indicators 3. Power Input 4. Grounding Jack 5. Foot-Plate Wire Jack 6. Test Button 7. Adjustable Audio Alarm 8. Left Foot LED Indicators 9. Toggle Switch 10.Wrist-Strap LED Indicators Assembly The PDT800 has two options for installation: Freestanding installation with a pedestal or wall mounting. 2

5 Free Standing Installation 1. Remove all items from carton and confirm you have received all items contained in the Parts Included List on page Remove plastic from the metal sensors of the footplate. 3. Thread Cord A through the pedestal with the straight plug emerging from the bottom. 4. Unscrew and remove the metal plate on the front of the footplate and set the screws aside. 5. Connect the straight plug to underside of footplate. See Image: 6. Slide the metal plate removed in Step 3 into the slot on the underside of the footplate. 7. Fasten the stand to the footplate with the four shorter screws that where removed earlier. 8. Thread CORD A s right angle plug through the smaller hole on the mounting plate and secure the plate to the top of pedestal with the included screws. 3

6 Installation Cont. 9. Attach the four spacer posts to the to the metal plate with a rubber washer between the post and plate. 10.Place the tester s plastic mounting board on the four posts with the rubber washers between the post and the plastic board and secure with screws. 11.Locate the AC power cord and Cord B and thread (the ends that fit the jacks on the bottom of the tester) though the large hole in metal plate and the hole in the backing board. 12.Connect the three cords to the tester. 13. Connect the banana plug of the Cord B to ground. 14. Plug in the power cord. Note: In free standing installation, it is recommended to have the unit against a wall for stability. Wall Mount The PDT800 can be mounted on to any flat, stationary surface. Frequently, the unit is mounted on a table or wall 1. Secure monitor to a solid wall with screws via the four holes in the corners of the mounting board. 4

7 Installation Cont. 2. Connect the footplate and monitor together with the footplate cord like Steps 3, 4, and 5 in Free Standing Installation. Place footplate directly under monitor 3. Connect the Power, Ground and Footplate cords to their proper jacks. 4. Connect the banana plug of Cord B to ground. 5. Plug in the power cord. Change Limits The high and low limits of both wrist strap and footwear can be changed by the DIP Switch located at the bottom of the tester. 1. Put all DIP switches to the UP position (0 means Open). Power off tester followed by a power on. 2. Set the desirable high limit and low limit of wriststrap and footwear. Then do a power off followed by a power on again. To change the low limit resistance for both wriststrap and footwear: Turn on DIP switch S1 to change the low limit resistance of both wriststrap and footwear from 1M to 750K ohm. Test Wrist OR Foot mode: Turn on DIP switch S2 to enable the Test wrist OR foot mode. Under this mode, the final result will be a PASS if either wrist or feet passed the test. Please note that if any test on wrist or feet is LOW, the final 5

8 test result will become a FAIL since the LOW test result implies a potential hazard to human body. DIP switch S3 controls the high resistance limit of wrist-strap testing as following: S3 OFF High Limit Resistance 10M ON 35M (Default) DIP switch S4 controls the low resistance limit of footwear testing as following: S4 OFF ON Low Limit Resistance 100K 1M (Default) DIP switch S5 and S6 control the high resistance limit of footwear testing as following: S5 S6 High Limit Resistance OFF OFF 10M OFF ON 35M ON OFF 100M(Default) ON ON 1G 6

9 Testing After the PDT800 is powered on, a short beep will sound and all the corresponding LED s turn on. Now the tester is ready to be used. Use the Toggle switch on the left-upper side of the tester to select the test you desire: UP: Down: Middle: Tests Wrist Strap Only Tests Footwear Only Tests Both Footwear and Wrist Strap Wrist Strap Only Testing 1. While wearing a wrist strap, insert the banana plug end of cord in the jack labeled WRIST STRAP 2. Toggle switch up for WRIST STRAP. 3. Press and hold the test button. 4. A short audible beep and a green LED labeled PASS lights up indicating that the wrist strap and cord are functioning properly. 5. If the red LED and a long beep activate than the wrist strap failed LOW. 6. If the yellow and green LED lights, along with two short beep sounds, than the wrist band FAILED HIGH. 7

10 Footwear Testing The PDT800 s duel footwear sensors allows for simultaneous testing of each foot independently. The left foot s status is indicated with the LED lights on the left side and the right foot is indicated on the right side of the monitor. 1. Turn the toggle switch located down to test FOOTWEAR 2. Place feet onto silver sensors of platform. 3. Press the test button and hold for 2-3 seconds 4. The green LED labeled PASS indicates that the grounding device is functioning properly. 5. The red LED labeled LOW the device is nearing failing levels and should be repaired or replaced. 6. The yellow LED labeled HIGH indicates the device has failed and is not longer grounding the operator. This indication is accompanied by audible alarm. Turnstile/Barrier/Gate System: The PDT series testers have a built in N/C N/O switch used with doors or turnstiles where a positive test allows the person to move through. The relay has contact rating of 1A 30VDC maximum, with the center contact as COMMON contact and the left contact as NC(normally close) and the right contact as NO(normally open). These are the inputs that are used to connect the device you want to trigger. 8

11 Product Specifications ESD Footwear Test: ESD Wrist-Strap Test: 100% Left/Right Foot Independent Testing Traditional Single Wrist-Strap Test Modes: High/Low Test Limits : Test Push Button: System Built-in Relay: WS only / FW only / Both WS and FW Factory default: Wrist 1MΩ~35MΩ / Foot 1MΩ~100MΩ. Accept customer preset at factory; range is 100KΩ~1GΩ. Ergonomic Metal Plate for Reliable/ Durable Operation. Dry Contact Control, 1A 30VDC Special Reminder: Indicate Near-Fail Test Result on LED Input Voltage: /VAC, 50/60Hz, 1A Operation Temperature: 0 C ~ 40 C, for Indoor Use Only System Dimension: 140x125x33 mm (L x W x H) Dual Independent Footplate Dimension: 480x403x25 mm (L x W x H) Parts Included List 1. PDT800 tester. 2. Foot plate. 3. Pedestal. 4. AC adapter 5. 2 connection cords. 6. Posts and Screws Cord A 9 Cord B

12 Service and Warranty Transforming Technologies, LLC provides a limited warranty for the Model PDT800. All new products are guaranteed to be free from defects in material and workmanship for a period of one (1) year from the date of shipment. Liability is limited to servicing (after evaluating, repairing or replacing) any product returned to Transforming Technologies. The company does not warrant damage due to misuse, neglect, alteration or accident. In no event shall Transforming Technologies be liable for collateral or consequential damages. To receive service under warranty, please contact Transforming Technologies Technical Support. About Transforming Technologies Since 1998, Transforming Technologies has helped electronic manufacturing facilities to protect their products and processes from the many serious problems associated with static electricity. Transforming Technologies offers a wide range of unique and outstanding products to detect, protect, eliminate and monitor electrostatic charges. Our products are integral components of an effective static control program King Rd Toledo, OH P: F: info@transforming-technologies.com