FX Input/Output (I/O) Modules XM07 and XM14

Transcription

1 Product Bulletin FX I/O Modules Issue Date July 6, 2009 FX Input/Output (I/O) Modules XM07 and XM14 The FX Input/Output (I/O) Modules provide additional physical input and output points for FX field controllers in the Facility Explorer range of products. The modules extend the capability of the FX16X Master Controller to monitor and control additional points within its control application. The modules do not perform control functions (See Figure 1). The FX I/O Module Series also includes models with manual s for a number of the analog, relay, and triac outputs. The manual function is always active when power is applied to the module. The manual function does not depend on communication with the FX16X Master Controller. XM07 modules have 18 physical inputs and outputs including relays and triacs, with four digital output s and two analog output s. XM14 modules have 31 physical inputs and outputs including relays and triacs, with seven digital output s and three analog output s. Both support a wide range of temperature sensors and actuating devices. Active sensors for the measurement of humidity, pressure, and other variables are also supported as well as digital (binary) inputs. The modules communicate with an FX16X Master Controller over its local link bus. Using the FX Tools software package, you can fully configure and program the FX16X Master Controller and its connected FX I/O Modules for a wide range of commercial Heating, Ventilating, Air Conditioning, and Refrigeration (HVACR) applications. XM07 I/O Module XM14 I/O Module XM07 I/O Module with Overrides XM14 I/O Module with Overrides Figure 1: FX Input/Output (I/O) Modules Features and Benefits Expanded Input and Output Capability of FX16X Master Controllers Fully Programmable Modules Using the FX Tools Software Package Similar Design and Physical Characteristics as FX Controllers Models with Overrides for Digital and Analog Outputs Light-Emitting Diode (LED) Indicators for Digital Inputs and Outputs Local Link Bus Connection Enables the FX16X Master Controller to cover a wider range of HVACR control applications using the extensive programming features of the FX Tools software package. Excludes the need for additional skills to design, commission, and service an application with FX I/O Modules. Are easy to configure and integrate into an FX platform control system. Direct control of monitored and controlled equipment for test purposes. Provide a clear presentation of the status of equipment at the local level for commissioning and service. Allows for easy connection and can be mounted remotely from the FX16X Master Controller to reduce wiring costs Johnson Controls, Inc. 1 Code No. LIT

2 Onboard Inputs and Outputs The FX I/O Modules support inputs and outputs with the following characteristics: Universal Inputs (UIs) (software configurable) A99 temperature sensor PT1000 Standard and Extended Range temperature sensors Ni1000 (Johnson Controls) temperature sensor Ni1000 Extended (Johnson Controls) temperature sensor Ni1000 Siemens (Landis+Gyr) temperature sensor Ni1000 DIN temperature sensor NTC 2.2k temperature sensor NTC 10k temperature sensor Active Voltage Active Ratiometric Active Current Potential-free contact Digital (Binary) Inputs (DIs) Voltage-free contacts LED indication with pulse counter option Digital (Binary) Outputs (DOs) relays (line voltage contacts) triacs (24 V or 230 VAC) LED indication manual switch (on-auto-off [I A 0]) Analog Outputs (AOs) (software configurable) 0-10 VDC at 10 ma Pulse Width Modulation (PWM) (100 Hz) Table 1 shows the number of inputs and outputs, and the number of manual s, available in the XM07 and XM14 model range. For full details see Technical Specifications. Table 1: Input and Outputs of FX I/O Modules Inputs and Outputs XM07 XM14 Universal Inputs 5 6 Digital (Binary) Inputs 4 12 Digital (Binary) Outputs 6 9 R = relay, T = triac 6R or 4R+2T 9R or 5R+4T With Override 4 7 Analog Outputs 3 4 With Override 2 3 Indicators and Controls Digital Input LEDs You can configure each digital input LED in the software application to illuminate green or red when the contact is open or closed. Green is normally used for a status indication and red for an alarm condition. Digital Output LEDs Digital output LEDs illuminate green when the output (relay contact or triac) is closed and the manual switch (if present) is in the auto position. For outputs with a manual switch, the LED illuminates amber when the switch is in the manual on position. Override on Analog Outputs Each output has a dial marked 0 10 with a push function to enable and disable the manual mode, which is indicated by an amber LED. See Figure 2 and Figure 3. Override on Digital Outputs Each output has a three-position switch labeled on-auto-off (I A O). In the on position, the digital output LED illuminates amber to indicate that you have overridden the output to the closed state. The manual s operate as long as power is applied to the module, and take priority over any command from the FX16X Master Controller application or supervisory system. See Figure 2 and Figure 3. 2 FX Input/Output (I/O) Modules XM07 and XM14

3 Figure 2: Override on XM07 Outputs Figure 3: Override on XM14 Outputs IMPORTANT: Do not use the manual switches for operations concerning the safety or emergency isolation of monitored and controlled equipment. The output relays of the XM module are controlled by firmware-driven electronic circuits and not directly by the manual switches. Local Link Communication Card The XM07 and XM14 modules are fitted with a local link (N2 Open) communication card for connection to the local link bus of an FX16X Master Controller. This allows the FX16X Master Controller to monitor and command the inputs and outputs of the XM modules as part of the control strategy in its software application. FX Tools Software Use the FX Tools software suite to program, download, test, and commission the FX I/O Modules as part of the application in the connected FX16X Master Controller. From the computer with the FX Tools software, you always communicate with the XM07 and XM14 modules through the FX16X Master Controller. FX Tools Pro CD includes: FX Builder used to program FX16X Master Controllers and FX I/O Modules. FX Builder provides complete flexibility in generating control applications. FX CommPro N2 used to download, test, and commission an FX16X Master Controller (including its XM modules) on an N2 Open network. FX CommPro LON used to download, test, and commission an FX16X Master Controller (including its XM modules) on a LONWORKS network. FX CommPro BACnet software used to download, test, and commission an FX16X Master Controller (including its XM modules) on a BACnet network. IMPORTANT: Use the XM07 I/O module and XM14 I/O module only as an operating control. Where failure or malfunction of the XM07 or XM14 module could lead to personal injury or property damage to the controlled equipment or other property, additional precautions must be designed into the control system. Incorporate and maintain other devices, such as supervisory or alarm systems or safety or limit controls, intended to warn of or protect against failure or malfunction of the XM07 or XM14 module. FX Input/Output (I/O) Modules XM07 and XM14 3

4 FX I/O Module Dimensions 108 (4.26) 60 (2.37) 56 (2.21) FIG: 07_dim_w/o_ovrd 118 (4.65) Figure 4: XM07 I/O Module Dimensions, mm (in.) 69 (2.72) 108 (4.26) 65 (2.56) FIG: 07_dim_w_ovrd 118 (4.65) Figure 5: XM07 I/O Module with Overrides Dimensions, mm (in.) 4 FX Input/Output (I/O) Modules XM07 and XM14

5 215 (8.47) 60 (2.37) 118 (4.65) 56 (2.21) FIG: 14 dim_w/o_ovrd Figure 6: XM14 I/O Module Dimensions, mm (in.) 215 (8.47) 69 (2.72) 118 (4.65) 65 (2.56) FIG: 14 dim_w_ovrd Figure 7: XM14 I/O Module with Override Dimensions, mm (in.) FX Input/Output (I/O) Modules XM07 and XM14 5

6 Ordering Codes Table 2 through Table 6 gives ordering information for the FX Input/Output Modules and accessories. Table 2: XM07 Module - 24 VAC Power Supply Product Code LP-XM07X01-000C LP-XM07X11-000C LP-XM07X51-000C LP-XM07X61-000C Description FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 6 DOs, 24 VAC power supply FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 2 Triac DOs, 4 DOs, 24 VAC power supply FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 6 DOs, 24 VAC power supply Overrides for 2 AOs and 4 DOs FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 2 Triac DOs, 4 DOs, 24 VAC power supply Overrides for 2 AOs, 2 Triac DOs, and 2 DOs Table 3: XM07 Module - 90 to 240 VAC Power Supply (Not Available in North America) Product Code LP-XM07B01-000C LP-XM07B11-000C LP-XM07B51-000C LP-XM07B61-000C Description FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 6 DOs, VAC power supply FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 2 Triac DOs, 4 DOs, VAC power supply FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 6 DOs, VAC power supply Overrides for 2 AOs and 4 DOs FX I/O Module with 5 UIs, 4 BIs, 3 AOs, 2 Triac DOs, 4 DOs, VAC power supply Overrides for 2 AOs, 2 Triac DOs, and 2 DOs Table 4: XM14 Module - 24 VAC Power Supply Product Code LP-XM14X01-000C LP-XM14X11-000C LP-XM14X51-000C LP-XM14X61-000C Description FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 9 DOs, 24 VAC power supply FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 4 Triac DOs, 5 DOs, 24 VAC power supply FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 9 DOs, 24 VAC power supply Overrides for 3 AOs and 7 DOs FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 4 Triac DOs, 5 DOs, 24 VAC power supply Overrides for 3 AOs, 2 Triac DOs, and 5 DOs Table 5: XM14 Module - 90 to 240 VAC Power Supply (Not Available in North America) Product Code LP-XM14B01-000C LP-XM14B11-000C LP-XM14B51-000C LP-XM14B61-000C Description FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 9 DOs, VAC power supply FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 4 Triac DOs, 5 DOs, VAC power supply FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 9 DOs, VAC power supply Overrides for 3 AOs and 7 DOs FX I/O Module with 6 UIs, 12 BIs, 4 AOs, 4 Triac DOs, 5 DOs, VAC power supply Overrides for 3 AOs, 2 Triac DOs, and 5 DOs Table 6: FX I/O Modules - Accessories Product Code LP-KIT C LP-KIT C LP-NET C LP-NET C Description Screw connectors kit for XM07 (replacement part kit included in each XM07 module) Screw connectors kit for XM14 (replacement part kit included in each XM14 module) Local link (N2 Open RS-485) communication card for XM07 (replacement part card included in each XM07 module) Local link (N2 Open RS-485) communication card for XM14 (replacement part card included in each XM14 module) 6 FX Input/Output (I/O) Modules XM07 and XM14

7 Technical Specifications Table 7: Universal Inputs (UI) - All Models Models Channel Type Remark/Application LP-XM07 All Models LP-XM14 All Models LP-XM07 and LP-XM14 UI1, UI2, UI3, UI4, UI5 UI1, UI2, UI3, UI4, UI5, UI6 See Universal Input Sensor Types in this Table. +5 V UI Power: 5 VDC ±10% at 20 ma max All Models +15 V UI/AO Power: 15 VDC ±10% at 80 ma max Universal Input Sensor Types Universal Input Sensors Software configurable. Application: temperature, humidity, pressure analog inputs at 16-bit resolution or equipment status binary inputs. Jumper for permanent current shunt path on one input UI1 on XM07 and UI6 on XM14. Used to power active or ratiometric sensors directly from the controller Used to power active sensors directly from the controller. (Also used for PWM outputs using 10 ma each.) Sensor Type Full Linearization Range Accuracy at 20 C (68 F) Module Circuits Only (Sensor Accuracy Not Included) A99-50 to 100 C (-58 to 212 F) ±0.5 C (±1 F) PT1000 Extended -50 to 160 C (-58 to 320 F) ±0.5 C (±1 F) Ni1000 (Johnson Controls) Ni1000 Extended (Johnson Controls) Ni1000 Siemens (Landis+Gyr) -45 to 120 C (-49 to 248 F) ±0.5 C (±1 F) 20 C (68 F) to 287 C (548.6 F) ±0.5 C (1 F) -50 C (-58 F) to 160 C (320 F) ±0.5 C (1 F) Ni1000 DIN -60 C (-76 F) to 180 C (356 F) ±0.5 C (1 F) NTC 2.2k -40 C (-40 F) to 150 C (302 F) ±0.5 C (1 F) NTC 10k -40 to 150 C (-40 to 300 F) ±0.5 C (±1 F) Active Voltage 0 10 VDC ±0.05 VDC Active Ratiometric VDC ±0.05 VDC Active Current 0(4) 20 ma ±0.2 ma Potential-free contact Binary open/close sense Not applicable Table 8: Digital (Binary) Input (DI) - All Models Model Channel Type Indication Remark/Application LP-XM07 All Models LP-XM14 All Models DI1, DI2, DI3, DI4 DI1, DI2, DI3, DI4, DI5, DI6, DI7, DI8, DI9, DI10, DI11, DI12 Potential-free contact open/close Software configurable LED (green or red) ON for closed or open contact Equipment status and events Transition counter at 50 Hz max Minimum Time ON: 10 ms Minimum Time OFF: 10 ms FX Input/Output (I/O) Modules XM07 and XM14 7

8 Table 9: XM07 Digital (Binary) Output (DO) Model Channel Type Indication Remark/Application LP-XM07X01-x LP-XM07B01-x (without manual ) DO1, DO2, DO3 DO4, DO5, DO6 Single- Pole, Single- Throw (SPST) 5(3)A, 250 VAC SPST 3(1)A, 250 VAC Heavy duty relay. Each relay contact set can be used with different voltage and Pilot relay. Each relay contact set can be used with different voltage and LP-XM07X11-x LP-XM07B11-x (without manual ) LP-XM07X51-x LP-XM07B51-x (with manual controls) DO1, DO2 DO3 Triac 0.5 A LP-XM07X11 24 VAC only LP-XM07B11 up to 230 VAC 5(3)A, 250 VAC DO4 DO6 SPST 3(1)A, 250 VAC DO1, DO2, DO3 DO4 DO5, DO6 5(3)A, 250 VAC SPST 3(1)A, 250 VAC SPST 3(1)A, 250 VAC triac on LED ON when contact closed amber LED ON when contact closed amber Frequently switching loads Heavy duty relay. contact set Pilot relay. Each relay contact set can be used with different voltage and Heavy duty relay. Each relay contact set can be used with different voltage and Pilot relay. contact set can be used with different voltage and Pilot relay. Each relay contact set can be used with different voltage and LP-XM07X61-x LP-XM07B61-x (with manual controls) Outputs DO1, DO2 DO3 DO4 DO5, DO6 Triac 0.5 A LP-XM07X61 24 VAC only LP-XM07B61 up to 230 VAC 5(3)A, 250 VAC SPST 3(1)A, 250 VAC SPST 3(1)A, 250 VAC LED ON when triac on amber LED ON when contact closed amber LED ON when contact closed amber Dielectric strength coil-contacts: 4,000 V RMS for 1 minute Dielectric test voltage on open relay contact: 1,000 VAC RMS Maximum relay switching rate at maximum load: Six operations/minute Average relay contact life: 30,000 operations at maximum load Frequently switching loads Heavy duty relay. contact set Pilot relay. contact set can be used with different voltage and Pilot relay. Each relay contact set can be used with different voltage and 8 FX Input/Output (I/O) Modules XM07 and XM14

9 Table 10: XM07 Analog Output (AO) Model Channel Type Indication Remark/Application All Models +15 V UI/AO Power 15 VDC +/-10% at 80 ma max LP-XM07X01-x LP-XM07X11-x LP-XM07B01-x LP-XM07B11-x (without manual ) LP-XM07X51-x LP-XM07X61-x LP-XM07B51-x LP-XM07B61-x (with manual ) AO1, AO2, AO3 AO1, AO2 AO VDC (10 ma max) or PWM output at 100 Hz cycle frequency with 10 ma sink from 15 VDC reference power source 0-10 VDC (10 ma max) or PWM output at 100 Hz cycle frequency with 10 ma sink from 15 VDC reference power source 0-10 VDC (10 ma max) or PWM output at 100 Hz cycle frequency with 10 ma sink from 15 VDC reference power source none none Amber LED ON when in manual mode dial marked: none Voltage reference source for PWM outputs (Also available for UI sensor power) Actuators and control devices Fan speed controller with PWM input 13-bit resolution accuracy ±0.1 VDC or 1% of full range Actuators and control devices Fan speed controller with PWM input 13-bit resolution accuracy ±0.1 VDC or 1% of full range Actuators and control devices Fan speed controller with PWM input 13-bit resolution accuracy ±0.1 VDC or 1% of full range FX Input/Output (I/O) Modules XM07 and XM14 9

10 Table 11: XM14 Digital (Binary) Output (DO) Model Channel Type Indication Remark/Application LP-XM14X01-x LP-XM07B01-x (without manual ) LP-XM14X11-x LP-XM14B11-x (without manual ) LP-XM14X51-x LP-XM14B51-x (with manual controls) LP-XM14X61-x LP-XM14B61-x (with manual controls) Outputs DO1, DO2, DO3, DO4, DO5, DO6, DO7, DO8, DO9 DO1, DO2, DO3, DO4, DO5 DO6, DO7, DO8, DO9 DO1, DO2, DO3, DO4, DO5, DO6, DO7 DO8, DO9 DO1, DO2, DO3, DO4, DO5 DO6, DO7 DO8, DO9 6(3)A, 250 VAC 6(3)A, 250 VAC Triac 0.5 A LP-XM14X11 24 VAC only LP-XM14B11 up to 230 VAC 6(3)A, 250 VAC 6(3)A, 250 VAC 6(3)A, 250 VAC Triac 0.5 A LP-XM14X61 24 VAC only LP-XM14B61 up to 230 VAC Triac 0.5 A LP-XM14X61 24 VAC only LP-XM14B61 up to 230 VAC triac on LED ON when contact closed amber LED ON when contact closed amber LED ON when triac on amber triac on Dielectric strength coil-contacts: 4,000 V RMS for 1 minute Dielectric test voltage on open relay contact: 1,000 VAC RMS Maximum relay switching rate at maximum load: Six operations/minute Average relay contact life: 30,000 operations at maximum load Heavy duty relay. Each relay contact set Heavy duty relay. Each relay contact set Frequently switching loads Heavy duty relay. Each relay contact set Heavy duty relay. Each relay contact set Heavy duty relay. Each relay contact set Frequently switching loads Frequently switching loads 10 FX Input/Output (I/O) Modules XM07 and XM14

11 Table 12: XM14 Analog Output (AO) Model Channel Type Indication Remark/Application All Models LP-XM14X01-x LP-XM14X11-x LP-XM14B01-x LP-XM14B11-x (without manual ) LP-XM14X51-x LP-XM14X61-x LP-XM14B51-x LP-XM14B61-x (with manual ) AO1 power 15 VDC ±10% at 10 ma max AO2 power 15 VDC ±10% at 10 ma max AO3, AO4 power AO1, AO2, AO3, AO4 AO1, AO2, AO3 AO4 15 VDC ±10% at 20 ma max 0-10 VDC (10 ma max) or PWM output at 100 Hz cycle frequency with 10 ma sink from 15 VDC reference power source 0 10 VDC (10 ma max) or PWM output at 100 Hz cycle frequency with 10 ma sink from 15 VDC reference power source 0 10 VDC (10 ma max) or PWM none none Amber LED ON when in manual mode dial marked none Voltage reference source for PWM outputs Actuators and control devices Fan speed controller with PWM input 13-bit resolution accuracy ±0.1 VDC or 1% of full range Actuators and control devices Fan speed controller with PWM input 13-bit resolution accuracy ±0.1 VDC or 1% of full range Actuators and control devices Fan speed controller with PWM input FX Input/Output (I/O) Modules XM07 and XM14 11

12 Table 13: XM07 and XM14 Models Product Codes Power Supply Requirements Power Consumption Housing Material Protection Class Ambient Operating Conditions Ambient Storage Conditions Dimensions (H x W x D) Weight (with Package) Digital (Binary) Output Override Analog Output Override I/O Ratings Connection for Digital Outputs and Power Connection for Inputs, Analog Outputs, and Local Link Bus Cable Length for Inputs FX Controller Support for I/O Modules on Local Link Bus (max) Agency Compliance Europe (all models) Canada (LP-XM07Xxx-x and LP-XM14Xxx-x models only) United States (LP-XM07Xxx-x and LP-XM14Xxx-x models only) LP-XM07xxx-xxxC and LP-XM14xxx-xxxC (See Ordering Codes) LP-XM07Xxx-xxxC and LP-XM14Xxx-xxxC: 24 VAC/DC ±15%, 50/60 Hz - Safety Extra-Low Voltage (SELV) in Europe Class 2 North America LP-XM07Bxx-xxxC and LP-XM14Bxx-xxxC: 90 to 240 VAC, 50/60 Hz - not available in North America LP-XM07Xxx-xxxC: 15 VA, 12 W maximum LP-XM07Bxx-xxxC: 19 VA, 12 W maximum LP-XM14Xxx-xxxC: 20 VA, 13 W maximum LP-XM14Bxx-xxxC: 24 VA, 13 W maximum ABS + polycarbonate, self-extinguishing: UL 94-V0 flammability rating IP20 CEI/EN to 50 C (-40 to 122 F), 10 to 95% RH (noncondensing) -40 to 70 C (-40 to 158 F), 10 to 95% RH (noncondensing) LP-XM07xxx-xxxC: 145 mm (5.71 in.) x 108 mm (4.26 in.) x 60 mm (2.36 in.) D = 69 mm (2.72 in.) with manual controls LP-XM14xxx-xxxC: 145 mm (5.71 in.) x 215 mm (8.46 in.) x 60 mm (2.36 in.) D = 69 mm (2.72 in.) with manual controls LP-XM07xxx-xxxC: 0.55 kg (1.2 lb) LP-XM14xxx-xxxC: 0.8 kg (1.8 lb) Three-position toggle switch: on-auto-off (I A 0) LED indicator: auto on = green, manual on = amber Dial marked 0 10 with push function for auto-manual mode LED indicator: manual mode = amber See tables throughout Technical Specifications Screw terminals for max 2 x 1.5 mm 2 (16 AWG) wires, included in the package Screw terminals for max 1 x 1.5 mm 2 (16 AWG) wires or 2 x Belden cable, 2-core twisted pair with shield 0.8 mm (20 AWG), included in the package Max 100 m (330 ft) with cables 0.6 mm, 22 AWG FX16X Controller Rev. A or Rev. B (not FX16D nor FX16 no Rev.) 4 x XM07 or 2 x XM14 or 2 x XM x XM /108 EEC, EMC Directive: EN , EN /95 EEC, Low Voltage Directive: EN UL Listed (PAZX7), CAN/CSA C22.2 No. 205, Signal Equipment Industry Canada, ICES-003 UL Listed (PAZX), UL 916, Energy Management Equipment FCC compliant to CFR 47, Part 15, Subpart B, Class A 12 FX Input/Output (I/O) Modules XM07 and XM14

13 Table 14: Local Link Bus (RS-485) Specifications RS-485 Bus; 9600 Baud Number of Devices End-of-Line Termination Electrical Isolation in XM07 and XM14 Maximum local link bus length: 1,200 m (4,000 ft), 0.8/0.6 mm (20/22 AWG) 2 x twisted pair with shield. Use the same cable type throughout segment. Maximum of 20 devices on local link bus 220 ohm at each end of segment >100 m (300 ft). For segment <100 m (300 ft), only one 220 ohm termination is required. 500 V The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or misuse of its products. Building Efficiency 507 E. Michigan Street, Milwaukee, WI Johnson Controls is a registered trademark of Johnson Controls, Inc. All other marks herein are the marks of their respective owners Johnson Controls, Inc. FX Input/Output (I/O) Modules XM07 and XM14 13