CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007)

Transcription

1 CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) CIB 3047 Comcode Issue 1

2 CIB 3047 (14B) 10-Button Voice Terminal Fixed Desk Stand and Wall Mount (32007) This bracket supports a 10-button voice terminal, either on a desk or mounted on a wall. This package contains the unassembled plastic desk stand/wall mount. If your voice terminal is to be wall mounted, you should have purchased the (D ) hardware kit for the wall mount separately from the 10-Button Voice Terminal Fixed Desk Stand and Wall Mount. The comcode number for the hardware kit is The pieces of the desk stand/wall mount come attached to one another (Figure 1). The names DESK SUPPORT, WALL SUPPORT, and BASE are imprinted on the appropriate plastic parts and separate instructions are given below for each application. Desk Support Wall Support Base FIGURE 1 Unassembled Desk Stand/Wall Mount iss 1, cib3047-1

3 Desk Stand Installation 1 Break the pieces apart from one another. 2 Locate the pieces labeled BASE and DESK SUPPORT. Remove the rough edges from these pieces where they were attached to each other. Set aside the wall support piece in case you later decide to wall mount your voice terminal. 3 Place the base right side up on a flat surface. Hold the desk support so its label is facing upward. Insert the angled tabs on the desk support into the slots on the base (Figure 2). DESK SUPPORT INSERT INTO BASE FROM TOP OF BASE FIGURE 2 Assembling the Disk Stand 4 Turn the voice terminal upside down. 5 Turn the assembled desk stand upside down. Position the stand on the voice terminal so that the stand s mounting slots fit just below the mounting tabs on the voice terminal (Figure 3). iss 1, cib3047-2

4 Mounting Slots Mounting Tabs Assembled desk stand (top view) Voice terminal (bottom view) Attaching the stand to the voice terminal (bottom view) FIGURE 3 Attaching the Desk Stand to the 10-Button Voice Terminal 6 Gently slide the stand upward so that the voice terminal tabs fit securely in the three mounting slots on the stand. 7 Thread one end of a (D8W) modular voice terminal cord between the base of the desk stand and the bottom of the voice terminal and plug it into the jack labeled LINE on the voice terminal. 8 Turn the voice terminal right side up and place it on a desk or table (Figure 4). iss 1, cib3047-3

5 10-Button Voice Terminal Desk Support Base FIGURE 4 10-Button Voice Terminal Attached to the Desk Stand 9 To remove the voice terminal from the desk stand, unplug the handset cord. Set the handset aside and turn the voice terminal over. Unplug the modular voice terminal cord. Slide the stand down and away from the voice terminal. Wall Mount Installation Break the pieces apart from one another. Locate the pieces labeled BASE and WALL SUPPORT. Remove the rough edges from these pieces where they were attached to each other. Use a blunt pointed object or the tip of a screwdriver to remove the four rubber feet in each corner on the bottom of the base. Set aside the desk support piece in case you later decide to mount your voice terminal on the desk stand. Place the base upside down on a table or desk and insert the tabs labeled A and B on the wall support into the slots labeled A and B on the base (Figure 5). iss 1, cib3047-4

6 Tab B Tab A FIGURE 5 Assembling the Wall Mount Lift the base and push the wall support through the slots until it fits firmly into place. Turn the base over. Select a location for installation at least as large as the voice terminal. Using a 3/16 drill bit, enlarge the four mounting screw holes in the base. Use the base as a template to mark the four mounting screw locations. Select the proper toggles for wall thickness: For walls 3/8 to 1/2 thick, use the smaller of the two sizes of toggles. For walls 5/8 to 3/4 thick, use the larger of the two sizes. For solid walls, either of the two sizes may be used. Using a 5/16 drill bit, drill a hole at each of the four mounting screw locations. Fold and insert a toggle into each of the mounting screw locations (Figure 6A). Tap each toggle with a hammer so that it is flush with the wall (Figure 6B). Pop the anchor open with the red key without using a hammer on the key (Figure 6C). iss 1, cib3047-5

7 Red key A B C FIGURE 6 Installing Toggles for Wall Mount 11 Insert the top two screws into the base and partially thread the screws into the toggles. 12 Insert the two remaining screws into the lower mounting holes and tighten all four screws (Figure 7). iss 1, cib3047-6

8 WALL SUPPORT INSERT INTO BASE FROM REAR OF BASE Top of base FIGURE 7 Wall Mount Attached to Wall Converting a Voice Terminal for Wall-Mounting 1 Remove the number card with a straightened paper clip or similar device and remove the number card (Figure 8). iss 1, cib3047-7

9 Switchhook button Paper clip Number card FIGURE 8 Removing the Number Card and Retainer 2 Remove the screw under the number card and lift out the handset from the upper housing (Figure 9). screw FIGURE 9 Retainer and Screw 3 Rotate the handset 180 degrees end-over-end (Figure 10). iss 1, cib3047-8

10 Rotate to wall mount position removed screw removed FIGURE 10 Rotating the Retainer 4 Replace the handset into the upper housing. If properly inserted, the handset should project into the handset well of the upper housing (Figure 11). screw screw after rotation FIGURE 11 Retainer in Wall Mount Position Replace the screw, the number card, and the umber card. Plug the (D8W) modular voice terminal cord into the jack labeled LINE on the bottom of the voice terminal. Position the voice terminal so that its mounting slots fit just above the mounting tabs on the wall mount (Figure 12). iss 1, cib3047-9

11 8 Gently slide the voice terminal down so the mounting tabs fit securely in the three mounting slots (Figure 12). Mounting slots Mounting tabs FIGURE 12 Attaching the Voice Terminal to the Wall Mount 9 To remove the voice terminal from the wall mount, slide the voice terminal up and away from the wall mount. iss 1, cib