Sensor supply in bus mode
|
|
- Nicholas Bates
- 5 years ago
- Views:
Transcription
1 Sensor supply in bus mode Product Family: TLE5011, TLE5012, TLE5012B, TLE5012BD, TLI5012B About this document Scope and purpose Some applications require the use of several devices connected to the same bus (e.g. safety-related applications). When one of the devices loses its supply voltage, it impacts the bus behavior. This document covers the two possible buses when using the sensors listed above and informs the user about the potential risks. Note: The following information is provided as advice for the implementation of the system only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the system. Intended audience This document is aimed at users in need of additional information when using more than one device in a bus mode configuration. Application Note 1 Rev
2 Sensor supply in bus mode Table of Contents About this document Table of Contents Description Bus system application - SSC interface Bus system application - SPC interface Revision History Application Note 2 Rev
3 Sensor supply in bus mode Description 1 Description When using two or more devices in a bus configuration and one of the devices loses its supply (), it disturbs the bus behavior and may corrupt the data transmitted by other devices connected to the bus. In this case protocol check mechanisms and the -off comparator check can be used to detect it (see: Datasheet / User Manual for more details about check mechanisms). When the application requires two sensors for data redundancy purpose (e.g. safety-related applications), Infineon recommends to use two separate buses. A more detailed information regarding this behavior can be provided on request. 1.1 Bus system application - SSC interface Sensor concerned by this application are: TLE5011 TLE5012 TLE5012B TLE5012BD TLI5012B The figure below (Figure 1) shows a typical implementation of a bus mode using SSC interface. The MCU controls the slaves by asserting / releasing the CSQ pins. Sensors are powered by different supplies (1 and x). The MCU is also powered via an additional supply (mcu). The faulty behavior appears when one of the sensors connected to the bus (S1 or S2) lose its supply voltage. The unpowered device is sinking current through the DATA pin. It results in changing voltage levels and/or timings. When the fault occurs, the bus behavior is dependent on the external circuitry such as series resistors, EMC capacitors, current capability of the MCU. The figure (Figure 1) represents only two sensors (S1 and S2) without additional components for clarity purpose. It shows a typical application with a push-pull output configuration (no pull-up resistors required). The issue is also present when using open-drain output configuration. Sensor 1 1 mcu MCU IFA CSQ CS1 IFB SCK SCK IFC DATA CCU Sensor x x IFA CSQ CS2 IFB SCK IFC DATA Figure 1 Application circuit with bus configuration (SSC interface) Application Note 3 Rev
4 Sensor supply in bus mode Description 1.2 Bus system application - SPC interface Sensor concerned by this application are: TLE5012B TLE5012BD The figure below (Figure 2) shows a typical implementation of a bus mode using SPC interface. The MCU is using the trigger nibble to address sensors connected to the bus. Sensors are powered by different supplies (1 and x). The MCU is also powered via an additional supply (mcu). The faulty behavior appears when one of the sensors connected to the bus (S1 or S2) lose its supply voltage. The unpowered device is sinking current through the OUT pin. It results in changing voltage levels and/or timings. When the fault occurs, the bus behavior is dependent on the external circuitry such as EMC-SENT filter and especially the pull-up resistor value (Rpu). Sensor 1 1 mcu MCU Rpu OUT CCU Sensor x x OUT Figure 2 Application circuit with bus configuration (SPC interface) Application Note 4 Rev
5 Sensor supply in bus mode Revision History 2 Revision History Revision Date Changes Application Note 5 Rev
6 Trademarks of Infineon Technologies AG All referenced product or service names and trademarks are the property of their respective owners. Edition Published by Infineon Technologies AG Munich, Germany 2018 Infineon Technologies AG. All Rights Reserved. Do you have a question about any aspect of this document? erratum@infineon.com Document reference IMPORTANT NOTICE The information contained in this application note is given as a hint for the implementation of the product only and shall in no event be regarded as a description or warranty of a certain functionality, condition or quality of the product. Before implementation of the product, the recipient of this application note must verify any function and other technical information given herein in the real application. Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind (including without limitation warranties of noninfringement of intellectual property rights of any third party) with respect to any and all information given in this application note. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office ( WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.
7 INFORMATION NOTE N 017/18 Dear Customer, With this INFINEON Technologies Information Note we would like to inform you about the following Application Note Sensor supply in bus mode affecting products TLE501x and TLI5012B Infineon Technologies AG Postal Address Headquarters: Am Campeon 1-15, D Neubiberg, Phone +49 (0) Chairman of the Supervisory Board: Wolfgang Mayrhuber Management Board: Dr. Reinhard Ploss (CEO), Dominik Asam, Dr. Helmut Gassel, Jochen Hanebeck Registered Office: Neubiberg Commercial Register Amtsgericht München HRB Page 1 of 2
8 INFORMATION NOTE N 017/18 Application Note Sensor supply in bus mode affecting products TLE501x and TLI5012B Products affected: Sales Name SP N OPN Package Please refer to 1_cip01718 attached Detailed Change Information: Subject: Application Note Sensor supply in bus mode affecting products TLE501x and TLI5012B Reason: When using two or more devices in a bus configuration and one of the devices loses its supply (), it disturbs the bus behavior and may corrupt the data transmitted by other devices connected to the bus. In this case protocol check mechanisms and the -off comparator check can be used to detect it (see: Datasheet / User Manual for more details about check mechanisms). When the application requires two sensors for data redundancy purpose (e.g. safety-related applications), Infineon recommends to use two separate buses. Description: Old New n/a Application Note Rev 1.0 (for details refer to 4_cip01718 attached) Product Identification: Not applicable Impact of Change: Not applicable Attachments: Application Note Rev. 1.0: 4_cip01718 Intended start of delivery: Valid with immediate effect. If you have any questions, please do not hesitate to contact your local Sales office Page 2 of 2
9 INF N 017/18 Application Note Sensor supply in bus mode affecting products TLE501x and TLI5012B Sales Name SP number OPN Package TLE5011 SP TLE5011FUMA1 PG-DSO-8 TLE5012 SP TLE5012FUMA2 PG-DSO-8 TLE5012B E1000 SP TLE5012BE1000XUMA1 PG-DSO-8 TLE5012B E3005 SP TLE5012BE3005FUMA1 PG-DSO-8 TLE5012B E3005 SP TLE5012BE3005XUMA1 PG-DSO-8 TLE5012B E5000 SP TLE5012BE5000XUMA1 PG-DSO-8 1_cip01718.xlsx Page 1 of 1 3/23/2018
TLx5012B 2go Evaluation Kit
About this document Scope and purpose This document describes the evaluation kit for the TLx5012B GMR based angle sensor. The purpose of this document is to describe the software installation process and
More informationApplication Note TLE9252V. About this document. Application Note. Safety Recommendations Z8F
Application Note TLE9252V Safety Recommendations About this document Scope and purpose This document provides application information for the transceiver TLE9252V from Infineon Technologies AG as Physical
More informationINFORMATION NOTE N 112/16. Early Problem Notification: DMA_TC.045_EPN_v1_0. Dear Customer,
INFORMATION NOTE N 112/16 Dear Customer, With this INFINEON Technologies Information Note we would like to inform you about the following Early Problem Notification: DMA_TC.045_EPN_v1_0 Infineon Technologies
More informationTLT807B0EPV Demoboard
Preface Scope and purpose This application note provides information about the usage of the TLT807B0 Demoboard. The TLT807B0 Demoboard is used to demonstrate the ultra low quiescent current linear voltage
More informationTxD GND V CC. RxD WAKE V IO SCLK MISO. (Top-side x-ray view) SCLK INH
Application Note PB Layout Recommendations for TLE9255W About this document Scope and purpose This document provides application information for the transceiver TLE9255W from Infineon Technologies AG as
More informationASCLIN Asynchronous Synchronous Interface
Asynchronous Synchronous Interface AURIX Microcontroller Training V1.0 2019-03 Please read the Important Notice and Warnings at the end of this document Port Control Asynchronous Synchronous Interface
More informationProduct / Process Change Notification
Product / Process Change Notification N 2016-067-A Dear Customer, Please find attached our INFINEON Technologies PCN: Introduction of new tester platform for final test for PROFET BTS432E2 E3062A, BTS442E2
More informationIndustrial PROFET. Universal Application Board User s Manual
Industrial PROFET Universal Application Board User s Manual Introduction Industrial PROFET Universal Application Board The Industrial PROFET demo board can be used to easily evaluate a wide range of single
More informationApplication Note - PCB Layout & PIN Behavior Assessment
Application Note - PB Layout & PIN Behavior Assessment Scope and purpose This document provides application information for the transceiver TLE9252V from Infineon Technologies AG as Physical Medium Attachment
More informationApplication Note No. 097
Application Note, Rev. 1.0, Mai. 2006 Application Note No. 097 Using BCR402R/BCR402U at High Supply Voltages RF & Protection Devices Edition 2006-05-08 Published by Infineon Technologies AG 81726 München,
More informationUser Guide for MA Evaluation Boards MA12040/MA12040P/MA12070/MA12070P
User Guide for MA Evaluation Boards MA12040/MA12040P/MA12070/MA12070P About this document Scope and purpose The Evaluation Board is an evaluation and demonstration board for MA12040, MA12040P, MA12070,
More informationOperating temperature T a
Ω Operating temperature T a -24 Green Product (RoHS Compliant) General Description N channel vertical power FET with charge pump, ground referenced CMOS compatible input, monolithically integrated in Smart
More informationDual H-Bridge shield. Dual H-Bridge shield - board user manual. Shield for DC motor control with IFX9202. About this document.
- board user manual Dual H-Bridge shield About this document Scope and purpose This document details the functionality and the required steps for running the Dual H-Bridge shield. Included are instructions
More informationSmart High-Side Power Switch BSP742RI PG-DSO8. AEC qualified Green product (RoHS compliant)
AEC qualified Green product (RoHS compliant) Ω PG-DSO8 General Description N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic feedback, monolithically
More informationSmart High-Side Power Switch for Industrial Applications One channel: 1 x 1 Ω
Smart High-Side Power Switch for Industrial Applications One channel: 1 x 1 Ω ITS 4140N Features Current controlled input Product Summary Overvoltage protection V bbin(az) 62 V Operating voltage V Short
More informationApplication Note, V1.0, Aug AP08064 XC866/886/888. Safeguarding the Microcontroller under Out-of-Spec Noise Conditions.
Application Note, V1.0, Aug. 2007 XC866/886/888 AP08064 Safeguarding the Microcontroller under Out-of-Spec Noise Conditions Microcontrollers Edition 2007-08 Published by Infineon Technologies AG 81726
More informationApplication Note, V 1.1, Apr AP08006 C868. Interfacing SPI/I2C Serial EEPROM with C868 Microcontroller. Microcontrollers. Never stop thinking.
Application Note, V 1.1, Apr. 2005 AP08006 C868 Interfacing SPI/I2C Serial EEPROM with C868 Microcontroller Microcontrollers Never stop thinking. Edition 2005-04-01 Published by Infineon Technologies AG
More informationSPOC +2 User Manual Multichannel SPI High-Side Power Controller
SPOC +2 User Manual About this document Scope and purpose This User Manual is intended to enable users to integrate the SPOC TM +2 Software for the SPOC TM +2- Demoboard. Intended audience This document
More informationPROFET TM + Demoboard. Automotive Power. Smart High-Side Power Switch - Demoboard Description. Rev. 1.4,
PROFET TM + Smart High-Side Power Switch - Demoboard Description Demoboard Rev. 1.4, 2011-02-16 Automotive Power Table of Contents Table of Contents 1 Overview.......................................................................
More informationNovalithIC H-Bridge Demo Board
Demo Board Description V1.0, 2011-09-23 Automotive Power General Description Figure 1 Demo board (top view) 1 General Description The NovalithIC H-Bridge/Dual-Halfbridge Demo Board contains two NovalithICs
More informationXMC1000 EEPROM emulation and data retention
AP32384 EEPROM emulation and data retention About this document Scope and purpose This document provides a brief introduction to the use of the Microcontroller family with emulated EEPROM. Intended audience
More informationTLE5xxx(D) Calibration 360
About this document Scope and purpose This document describes the calibration algorithm and the correct implementation for GMR/TMR-based analog angle sensors TLE5xxx(D) with a measurement range of 360.
More informationApplication Note, V1.0, Jul AP08049 XC886/888CLM. Migration of Flash to ROM Device: Memory Protection Configurations.
Application Note, V1.0, Jul. 2006 AP08049 XC886/888CLM Migration of Flash to ROM Device: Memory Protection Configurations Microcontrollers Edition 2006-07 Published by Infineon Technologies AG 81726 München,
More information3D Magnetic Sensor 2 Go - TLE493D-A2B6
TLE493D-A2B6 3D-MS2GO User Manual About this document Scope and purpose This document provides an introduction to the 3D Magnetic Sensor 2 Go kit and should enable the reader to efficiently carry out own
More informationLinear movement with a 3D sensor
About this document Scope and purpose After reading this application note you will know how to make the magnetic design for a linear movement application with a Hall based 3D sensor. Directly, magnet and
More informationOPTIGA TM Trust B SLE95250
OPTIGA TM Trust B SLE95250 Evaluation Kit User Guide About this document Scope and purpose This is the User Guide for OPTIGA TM Trust B evaluation kit. It gives the detailed guideline of how to use OPTIGA
More informationIRPS5401 programming guide
TB0035 About this document Scope and purpose The scope of this document covers the functionality of the Non-volatile Memory (NVM) space of the USER and CNFG sections of the IRPS5401 PMIC device. The purpose
More informationRelaisdriving with HITFETs and SPIDERs
Relaisdriving with HITFETs and SPIDERs Driving automotive relais with protected low side drivers Application Note HITFET AP01-2009 Rev. 1.1 April 2011 Automotive Power HITFETS Table of Contents Table of
More informationXC2000 Family AP Application Note. Microcontrollers. XC2236N Drive Card Description V1.0,
XC2000 Family AP16179 Application Note V1.0, 2010-07 Microcontrollers Edition 2010-07 Published by Infineon Technologies AG 81726 Munich, Germany 2010 Infineon Technologies AG All Rights Reserved. LEGAL
More informationApplication Note, V1.3, September 2008 AP XC2000/XE166 Family. Microcontrollers
Application Note, V1.3, September 2008 AP16103 XC2000/XE166 Family P i n C o n f i g u r a t i o n, P o w e r S u p p l y a n d R e s e t Microcontrollers Edition 2008-09-18 Published by Infineon Technologies
More informationApplication Note, V 1.1, Feb AP DAP Connector. Microcontrollers
Application Note, V 1.1, Feb. 2009 AP24003 Microcontrollers Edition 2009-02 Published by Infineon Technologies AG 81726 München, Germany Infineon Technologies AG 2009. All Rights Reserved. LEGAL DISCLAIMER
More informationXE166 Family AP Application Note. Microcontrollers. X E D r i v e C a r d H a r d w a r e D e s c r i p t i o n Board REV.
XE166 Family AP16160 X E 1 6 4 D r i v e C a r d H a r d w a r e D e s c r i p t i o n Application Note V1.0, 2009-03 Microcontrollers Edition 2009-03 Published by Infineon Technologies AG 81726 Munich,
More informationLOW EMI PWM INTELLIGENT POWER HIGH SIDE SWITCH
Automotive grade Automotive IPS High side AUIPS72211R LOW EMI PWM INTELLIGENT POWER HIGH SIDE SWITCH Features Integrated bootstrap for 100kHz switching Optimized EMI switching Charge pump for DC operation
More informationScope: SW Installation: Start the Package PROG-KIT. Current. Page 1
Sensor 2 Go Quick Instruction Guide Scope: The following instruction gives a quick overview about the Sensor r 2 Go GUI. The GUI can also be used for the PGSISI-2 based TLI4970050 PROG-KIT. SW Installation:
More informationSPI Protocol of the TLE941xy family
Protocol of the TLE941xy family Application Note Rev 1.0, 2016-04-25 Automotive Power Table of Contents 1 Abstract........................................................................ 3 2 Introduction.....................................................................
More informationXMC LED current control explorer kit
XMC LED current control explorer kit Quick start guide The XMC LED current control explorer kit is an evaluation kit that introduces the user to continuous conduction mode buck LED driving solution with
More information.dp Interface Gen2 Firmware Update for XDPL8220
White Paper Revision 1.0 About this document Scope and Purpose The increased functionality of the XDPL8220 Digital PFC+Flyback Controller IC requires firmware version 2.4.3 or newer in the.dp Interface
More informationTLS202B1. Demonstration Board Manual. Automotive Power. Demonstration Board Manual. Rev. 1.0,
Rev. 1.0, 2013-06-12 Automotive Power Introduction 1 Introduction The TLS202B1 application board is a demonstration of the Infineon low drop out linear voltage post regulator. The TLS202B1 is the ideal
More informationTLE9845 Application Kit PN User s Manual
Product Family: TLE984xQX Figure 1 TLE9845QX Application Kit with PN-Halfbridge About this document Scope and purpose The TLE9845_APPKIT_PN is designed to evaluate hardware and software functionalities
More informationApplication Note, V 1.0, April 2005 AP32086 EMC. Design Guideline for TC1796 Microcontroller Board Layout. Microcontrollers. Never stop thinking.
Application Note, V 1.0, April 2005 AP32086 EMC Design Guideline for TC1796 Microcontroller Board Layout Microcontrollers Never stop thinking. TriCore Revision History: 2005-04 V 1.0 Previous Version:
More informationGetting Started with the XDPL8220 Reference Board Using.dp Vision Software
AN_GS_201611_PL21_003 Getting Started with the XDPL8220 Reference Board Using.dp Vision Software XDP T M digital power About this document Scope and purpose The purpose of this document is to give a quick
More informationPower Management & Drives. Application Note. February AN-EVAL 2x8-ISO1H815G-1
February 2010 Application Note AN-EVAL 2x8-ISO1H815G-1 Coreless Transformer Isolated High Side Switch Evaluation Board 2 x 8 Channel 1.2A with ISO1H815G Published by Infineon Technologies AG http://www.infineon.com
More informationAP XC2000 & XE166 Families. Design Guidelines for XC2000 & XE166 Microcontroller Board Layout. Microcontrollers
Application Note, V2.1, Jun. 2008 AP16116 XC2000 & XE166 Families Design Guidelines for XC2000 & XE166 Microcontroller Board Layout Microcontrollers Edition 2008-06-24 Published by Infineon Technologies
More informationXE164 UConnect Manual, V.1.1, February XE164 UConnect. Board REV. 2007/40. Microcontrollers. Never stop thinking.
Manual, V.1.1, February 2008 XE164 Board REV. 2007/40 Microcontrollers Never stop thinking. Edition 2007-06 Published by Infineon Technologies AG 81726 München, Germany Infineon Technologies AG 2008. All
More informationChip Card & Security ICs SLE Intelligent 256-Byte EEPROM with Write Protection function and Programmable Security Code
Chip Card & Security ICs SLE 5542 Intelligent 256-Byte EEPROM with Write Protection function and Programmable Security Code Short Product Information May 2006 Short Product Information Revision History:
More informationApplication Note No. 100
Application Note, Rev. 1.2, May 2007 Application Note No. 100 ESD Protection for High-Speed Applications 1- & 2-channel low capacitance bi-directional ESD diode in ultra-small TSLP package Small Signal
More informationXE166 Family AP Application Note. Microcontrollers. UConnect XE162N Hardware Description V1.0,
XE166 Family AP90005 Application Note V1.0, 2010-01 Microcontrollers Edition 2010-01 Published by Infineon Technologies AG 81726 Munich, Germany 2010 Infineon Technologies AG All Rights Reserved. LEGAL
More informationMCETool V2 User Manual
AN2017-02 Quality requirement category: Industry Features Programming of RAM, Flash and OTP memory for IRMCKxxx and IRMCFxxx devices Debugging via standard JTAG interface Tuning of motor parameters via
More informationChip Card & Security ICs SLE Intelligent 1024 Byte EEPROM with Write Protection and Programmable Security Code
Chip Card & Security ICs SLE 5528 Intelligent 1024 Byte EEPROM with Write Protection and Programmable Security Code Short Product Information May 2007 Short Product Information Revision History: Current
More informationDesign Guideline for TC1782 Microcontroller Board Layout
TC1782 AP32145 Application Note V1.4 2012-02 Microcontrollers Edition 2012-02 Published by Infineon Technologies AG 81726 Munich, Germany 2012 Infineon Technologies AG All Rights Reserved. LEGAL DISCLAIMER
More informationRF Power Product Selection Guide LDMOS Transistors and ICs
RF Power Product Selection Guide LDMOS Transistors and ICs www.infineon.com/rfpower RF Power Product Selection Guide INFINEON S state-of-the-art LDMOS technology, high-volume manufacturing facilities and
More informationEasy Kit Board Manual
User s Manual, V1.0, June2008 Easy Kit Board Manual Easy Kit - XC88x Microcontrollers Edition 2008-06 Published by Infineon Technologies AG, 81726 München, Germany Infineon Technologies AG 2008. All Rights
More informationSecurity & Chip Card ICs SLE 55R04. Intelligent 770 Byte EEPROM with Contactless Interface complying to ISO/IEC Type A and Security Logic
Security & Chip Card ICs SLE 55R04 Intelligent 770 Byte EEPROM with Contactless Interface complying to ISO/IEC 14443 Type A and Security Logic Short Product Information January 2001 Short Product Information
More informationAbsolute Pressure Sensor
November 2007 Absolute Pressure Sensor Data Sheet Rev 2.14 Sense & Control Edition 2007-11-23 Published by Infineon Technologies AG 81726 München, Germany 2007 Infineon Technologies AG All Rights Reserved.
More informationESD5V3U4RRS. Type Package Configuration Marking ESD5V3U4RRS SOT363 6 pins, uni-directional E8s
UltraLow Capacitance ESD Diode Array Railtorail diodes with internal TS diode ESD / transient protection of four lines and one cc line exceeding: IEC00 (ESD): ± 5 k (contact) IEC00 (EFT):.5 k / 50 A (5/50
More informationApplication Note AN V1.3 August Module with adapted driver electronics
MIPAQ serve Edition 2013-08-16 Published by Infineon Technologies AG 59568 Warstein, Germany Infineon Technologies AG 2013. All Rights Reserved. Attention please! THE INFORMATION GIVEN IN THIS APPLICATION
More informationESD8V0L... ESD8V0L1B-02LRH. Type Package Configuration Marking ESD8V0L1B-02EL
Low Capacitance TVS Diode ESD / transient protection of highspeed data lines in. / 5 / V applications according to: IEC6000 (ESD): up to ± 5 KV (contact) IEC6000 (EFT): 0 A (5/50 ns) IEC60005 (surge):
More informationDesign Guideline for TC1791 Microcontroller Board Layout
TC1791 AP32162 Application Note V1.2 2012-02 Microcontrollers Edition 2012-02 Published by Infineon Technologies AG 81726 Munich, Germany 2012 Infineon Technologies AG All Rights Reserved. LEGAL DISCLAIMER
More informationDocumentation Addendum, V1.2, Aug TC Bit Single-Chip Microcontroller Delta BC-to-BE Step. Microcontrollers
Documentation Addendum, V1.2, Aug. 2007 TC1796 32-Bit Single-Chip Microcontroller Microcontrollers Edition 2007-08 Published by Infineon Technologies AG 81726 Munich, Germany 2007 Infineon Technologies
More informationApplication Note No. 104
Application Note, Rev. 1.0, August 2007 Application Note No. 104 2-channel bi/uni-directional TVS diodes for ESD protection in /LIN bus applications ESD24VS2B, ESD24VS2U Small Signal Discretes Edition
More informationFrequently Asked Questions
Product Name: System Basis Chips (SBCs) Date: April 2013 Application: Automotive ECUs Datasheet: www.infineon.com/sbc Contact Person: Norbert Ulshoefer/Antonio Monetti Note: The following information is
More informationApplication Note, V1.0, November AP XC2000/XE166 family. ADC Result Handling on XC2000/XE166 family of Microcontrollers.
Application Note, V1.0, November. 2008 AP16155 XC2000/XE166 family ADC Result Handling on XC2000/XE166 family of Microcontrollers Microcontrollers Edition 2008-11-11 Published by Infineon Technologies
More informationDesign Guideline for TC1798 Microcontroller Board Layout
TC1798 AP32164 Application Note V1.2 2012-02 Microcontrollers Edition 2012-02 Published by Infineon Technologies AG 81726 Munich, Germany 2012 Infineon Technologies AG All Rights Reserved. LEGAL DISCLAIMER
More informationUM NVT2001GM and NVT2002DP demo boards. Document information
Rev. 7 March 202 User manual Document information Info Keywords Abstract Content NVT, voltage translator, level translator, level shift, passive voltage translator, passive level translator, passive level
More informationApplication Note, V1.0, Jul AP XC16x. Interfacing the XC16x Microcontroller to a Serial SPI EEPROM. Microcontrollers
Application Note, V1.0, Jul. 2006 AP16095 XC16x Interfacing the XC16x Microcontroller to a Serial SPI EEPROM Microcontrollers Edition 2006-07-10 Published by Infineon Technologies AG 81726 München, Germany
More informationUM NVT2008PW and NVT2010PW demo boards. Document information
Rev. 1 March 20 User manual Document information Info Keywords Abstract Content NVT, voltage translator, level translator, level shift, passive voltage translator, passive level translator, passive level
More informationEval Kit Manual. DN[Document ID] AS6200. Adapter Board AS6200-WL_EK_AB. ams Eval Kit Manual Page 1
Eval Kit Manual DN[Document ID] AS6200 Adapter Board AS6200-WL_EK_AB ams Eval Kit Manual Page 1 Content Guide 1 Introduction... 3 1.1 Kit Content... 3 2 Getting Started... 4 3 Hardware Description... 4
More informationTLE986xQX Family TLE987xQX Family. Overview. Delta Sheet. This document lists all differences between BE-Step and BF-Step.
Delta Sheet TLE986xQX Family Overview This document lists all differences between -Step and BF-Step. This document applies to the following products: TLE9861QXA20 TLE9867QXA20 TLE9867QXA40 TLE9869QXA20
More informationServer side management system for multiple IoT terminals in industrial systems
Infineon Network Use Case Server side management system for multiple IoT terminals in industrial systems This system utilizes the technology of the Trusted Computing Group (TCG) as a time-to-market solution
More informationGetting started with X-NUCLEO-53L1A1 long distance ranging ToF sensor expansion board based on VL53L1X for STM32 Nucleo
User manual Getting started with X-NUCLEO-53L1A1 long distance ranging ToF sensor expansion board based on VL53L1X for STM32 Nucleo Introduction This document provides detailed hardware information on
More informationQueued SSC V
TriCore AP32172 Application Note V1.0 2011-09 Microcontrollers Edition 2011-09 Published by Infineon Technologies AG 81726 Munich, Germany 2011 Infineon Technologies AG All Rights Reserved. LEGAL DISCLAIMER
More informationDatasheetDirect.com. Visit to get your free datasheets. This datasheet has been downloaded by
DatasheetDirect.com Your dedicated source for free downloadable datasheets. Over one million datasheets Optimized search function Rapid quote option Free unlimited downloads Visit www.datasheetdirect.com
More informationBootstrap Circuitry Selection for Half-Bridge Configurations
Application Report Bootstrap Circuitry Selection for Half-Bridge Configurations Mamadou Diallo, High Power Drivers ABSTRACT Driving MOSFETs in half-bridge configurations present many challenges for designers.
More informationCRC Computation using PCP
TriCore Family AP32171 Application Note V1.0 2010-09 Microcontrollers Edition 2010-09 Published by Infineon Technologies AG 81726 Munich, Germany 2010 Infineon Technologies AG All Rights Reserved. LEGAL
More informationMotor control power board based on the SLLIMM-nano 2 nd series
Motor control power board based on the SLLIMM-nano 2 nd series Data brief Motor control connector (32 pins) interfacing with ST MCU boards Universal design for further evaluation with bread board and testing
More informationTLE8110ED Switching Inductive Loads and External Clamping
TLE8110ED Switching Inductive Loads and External Clamping Product Family: Flex Multichannel Low-Side Switches About this document Scope and purpose This application note is intended to provide additional
More informationX-NUCLEO-53L0A1 ranging and gesture detection sensor expansion board based on VL53L0X for STM32 Nucleo
User manual X-NUCLEO-53L0A1 ranging and gesture detection sensor expansion board based on VL53L0X for STM32 Nucleo Introduction This document provides detailed hardware information on X-NUCLEO-53L0A1 expansion
More informationUM PCAL6524 demonstration board OM Document information
Rev. 1 23 September 2015 User manual Document information Info Content Keywords OM13320 Fm+ development kit, OM13260 Fm+ I2C bus development board, OM13303 GPIO target board Abstract Installation guide
More informationEBV Personalization Services for Security Devices
Infineon Security Partner Network Partner Use Case EBV Personalization Services for Security Devices Secured generation and storage of personalized OEM certificates in the OPTIGA Trust E for sophisticated
More informationIMPORTANT NOTICE. use
Rev. 05 2 January 2008 Product data sheet IMPORTANT NOTICE Dear customer, As from October 1st, 2006 Philips Semiconductors has a new trade name -, which will be used in future data sheets together with
More informationAN Automatic RS-485 address detection. Document information
Rev. 01 2 June 2006 Application note Document information Info Keywords Abstract Content SC16IS740, SC16IS750, SC16IS760, SC16IS752, SC16IS762, I2C UART, SPI UART, RS-485, 9-bit mode, multi-drop mode This
More informationPlease refer to "4. Evaluation Board" on page 2 for more information about these steps. Figure 1. System Connections
CP2120 EVALUATION KIT USER S GUIDE 1. Kit Contents The CP2120 Evaluation Kit contains a CP2120 evaluation board and a power supply. The following supporting documents can be downloaded from www.silabs.com:
More informationLED Testing and Control Using PSoC
Application Note AN2372 LED Testing and Control Using Author: David Johnson Associated Project: Yes Associated Part Family: CY8C21434 and CY8C24794 Software Version: Designer 4.2 SP2 and Express 2.0 Abstract
More informationWorking around ERR7026 according to application needs
Freescale Semiconductor Document Number: EB795 Engineering Bulletin Rev. 0, 08/2013 Working around ERR7026 according to application needs by: Automotive and Industrial Solutions Group 1 Introduction This
More informationSTEVAL-IPMnM2N. Motor control power board based on the SLLIMM-nano 2 nd series. Description. Features. RoHS compliant
Motor control power board based on the SLLIMM-nano 2 nd series Data brief RoHS compliant Features Input voltage: from 125 to 400 VDC Nominal power: up to 100 W Nominal current: up to 1.2 A rms Input auxiliary
More informationOPTIGA TPM SLB 9670 TPM1.2
Data Sheet Devices SLB 9670VQ1.2 SLB 9670XQ1.2 Key Features Compliant to TPM Main Specification, Version 1.2, Rev. 116 (see [1]) SPI interface Approved for Google Chromebook / Chromebox Standard (-20 C
More informationS3 Flash In-System Programmer
S3 Family of Microcontrollers S3 Flash In-System Programmer UM026604-0816 PRELIMINARY Copyright 2016 Zilog, Inc. All rights reserved. www.zilog.com ii Warning: DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
More informationAN2672 Application note
Application note I²C application examples Introduction The I 2 C peripheral is very flexible, supporting standard interrupts in both 10-bit and 7-bit addressing modes. As a result, generated events are
More informationAS5510. User Manual AS5510 Adapterboard. 10-bit Linear Incremental Position Sensor with Digital Angle output
User Manual Adapterboard 10-bit Linear Incremental Position Sensor with Digital Angle output www.ams.com Revision 1.2-22/08/13 page 1/12 -AB-Manual Table of Contents 1 General Description... 3 2 List of
More informationPNP 500 ma, 50 V resistor-equipped transistor; R1 = 2.2 kω, R2 = open
PNP 500 ma, 50 V resistor-equipped transistor; R1 = 2.2 kω, R2 = open Rev. 4 8 November 2010 Product data sheet 1. Product profile 1.1 General description 500 ma PNP Resistor-Equipped Transistor (RET)
More informationBroadband system applications i.e. WCDMA, CATV, etc. General purpose Voltage Controlled Attenuators for high linearity applications
Rev. 2 6 March 2012 Product data sheet 1. Product profile 1.1 General description Quad PIN diode in a SOT753 package. 1.2 Features and benefits 4 PIN diodes in a SOT753 package 300 khz to 4 GHz High linearity
More informationZSSC4151 Evaluation Kit Hardware Manual
Important Notes Restrictions in Use IDT s ZSSC4151 SSC Evaluation Kit, consisting of the SSC Communication Board (SSC CB), ZSSC415x/6x/7x Evaluation Board (SSC EB), Sensor Replacement Board (SSC RB), and
More informationEvaluation Board for CS3308. Description CS Channel. Digitally Controlled Analog Volume Control. PC or External Serial Control Input
Evaluation Board for CS3308 Features Description Single-ended Analog Inputs Single-ended Analog Outputs Supports AC and DC-Coupled Analog I/O Flexible Serial Control I/O Headers Serial Control Input Header
More informationiotrust Security Solutions
Infineon Security Partner Network Partner Use Case iotrust Security Solutions Entrust Datacard iotrust Security Solutions allow customers to establish secured IoT infrastructures from sensor to cloud,
More informationApplication Note. DN [Document ID] AS72xx. How to Program AS72xx Firmware with FlashCatUSB. ams Application Note Page 1
Application Note DN [Document ID] AS72xx How to Program AS72xx Firmware with FlashCatUSB ams Application Note Page 1 Application Note DN [Document ID] Content Guide 1 Components and installations... 3
More informationAN2667 Application note
Application note STM8A GPIO application examples Introduction This document is intended to provide two practical application examples of the GPIO peripheral use in the STM8A device. The examples are: Toggling
More informationHX2VL Development Kit Guide. Doc. # Rev. *A
HX2VL Development Kit Guide Doc. # 001-73960 Rev. *A Cypress Semiconductor 198 Champion Court San Jose, CA 95134-1709 Phone (USA): 800.858.1810 Phone (Intnl): 408.943.2600 http://www.cypress.com Copyrights
More informationUSER GUIDE. Atmel OLED1 Xplained Pro. Preface
USER GUIDE Atmel OLED1 Xplained Pro Preface Atmel OLED1 Xplained Pro is an extension board to the Atmel Xplained Pro evaluation platform. The board enables the user to experiment with user interface applications
More informationSecurity & Chip Card ICs SLE 4436/36E
Security & Chip Card ICs SLE 4436/36E Intelligent 221 Bit EEPROM Counter for > 20000 Units with Security Logic and High Security Authentication Short Product Information 07.99 6KRUW3URGXFW,QIRUPDWLRQ 5HYLVLRQ+LVWRU\
More informationEV-VNQ7003SY. VNQ7003SY Evaluation Board. Data brief. Features. Applications. Description
EV-VNQ7003SY Data brief VNQ7003SY Evaluation Board Features Channel 0- -3 Product status link EV-VNQ7003SY Vcc 4 to 8 V RON(typ) ILIMH(typ) 5 mω 35 A 7 mω 80 A Simple single IC application board dedicated
More information