User Guide Guangzhou Zhiyuan Electronics Stock Co., LTD

Transcription

1 Platform EPCM-505C User Guide Guangzhou Zhiyuan Electronics Stock Co., LTD

2

3 Safety information Electrical safety To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocation the system When adding or removing devices to or from the system, ensure that the power cables for the device are unplugged before the signal cables are connected. If possible, disconnect all power and signal cables from the system before you add or remove device. Before connecting or removing signal cables form the platform, ensure that all power cables are unplugged. Seek professional assistance before using an adapter or extension card. These devices could interrupt the grounding circuit. Ensure that your power supply is set to the correct voltage in your area. If you are not sure about the voltage of the electrical outlet you are using, contact your local power company. If the power supply is broken, do not try to fix it by yourself. Please contact us. Operating safety Before installing the platform and adding devices on it, carefully read the manuals that came with the package. Before using the product, ensure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact us immediately. To avoid short circuits, keep paper clips, screws, and staples away from the platform. Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet. Place the product on a stable surface. If you encounter technical problems with the platform, please contact us. Users MUST not remove the heat skin and cooler fan. Remove the heat skin or cooler fan may cause ICs over heat damage. Don t touch the heat skin. The temperature of the heat skin may rise to 55 Centigrade/131 Fahrenheit. Contact Information Name: Wangyi Li esdc@zlg.cn Phone: (9:00~17:00 Beijing Time) I

4 About this guide This user guide contains the information you need when installing and configuring the platform. Conventions used in this guide To ensure that you perform certain tasks properly, take note of the following symbols used throughout this manual. DANGER/WARNING: Information to prevent injury to yourself when you trying to complete a tack. Caution: Information to prevent damage to the components when you trying to complete a task. IMPORTANT: Instructions you MUST follow to complete a task. NOTICE: Tips and additional information help you complete a task. Typography Bold text Indicates a menu or an item to select Italics Used to emphasize a word or a phrase <Key> Key enclosed in a pair of angle brackets means that you must press the enclosed key. <Key1> + <Key2> + <Key3> If you must press two or more keys simultaneously, the keys are linked with a plus sign (+). Example: <Ctrl> + <Alt> + <Del> II

5 Platform Specifications Processor Intel Atom E645C processor 1.0 GHz single core with Intel Hyper-Threading Technology Intergraded Altera FPGA Memory 1 GByte DDR2-800 on board memory IOH Intel EG20T Storage 1 SATA 1.5Gbps port by Intel EG20T 1 onboard CF card slot, support CF card type II PCIE 1 Mini PCIE slot onboard Connectors Back Panel I/O 1 12V DC power supply port 2 serial ports, 1 support RS232/RS485 1 microphone input jack 1 line out jack 1 video input 1 CAN 2.0B port 1 12Bit ADC port 1 8Bit ADC port 1 12bit DAC port 4 USB 2.0 high speed ports 1 VGA port III

6 1 Ethernet by EG20T, supports IEEE Ethernet by FPGA Onboard connectors 1 Low Pin Count (LPC) interface 1 I 2 C interface 1 SPI interface 1 Camera interface 1 Serial port config pin 1 Alter FPGA JTAG 1 H.D.D power supply IV

7 Capter 1 Product information 1.1 Package contents Check your platform package for the following items. EPCM-505C Platform User guide 1 x FPGA adapter 1 x RS232 cable(female to female) 1 x RS232 cable(male to female) 1 x Peripheral connector to SATA cable 1 x Peripheral connector conversion cable 1 x Ethernet cable 1 x Terasic USB balter 1 x LA1016 logic analyzer 1 x power supply module If any of the above items damaged or missing, contact us. The illustrated items above are for reference only. Actual product specification may vary with different modules. 1

8 Capter 2 Hardware information 2.1 Before you proceed Take note of the following precautions before you install platform or change any platform settings. Unplug the power cord from the wall socket before touching any components. Before handling components, use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, to avoid damaging them due to static electricity. Hold the components by the edges to avoid touching the ICs on them. Whenever you uninstall any components, place it on a grounded antistatic pad or in the bag that came with the components. Before you install or remove any components, ensure that power cord is unplugged from the power supply. 2

9 2.2 Platform overview Platform layout The platform consists of 5 parts. No. 1 LCD screen & touch screen assembly 2 Base board 3 CPU core board 4 Heat skin 5 Cooler fan Description Users MUST not remove the heat skin and cooler fan. Remove the heat skin or cooler fan may cause ICs over heat damage. Don t touch the heat skin. The temperature of the heat skin may rise to 55 Centigrade/131 Fahrenheit. Users may remove the LCD screen module, if it is not needed. 3

10 2.2.2 Base board layout No. 1 Altera HSMC connector 2 FPGA Button 3 Camera Interface 4 FPGA LEDs 5 LPC(Low pin count) 6 Serial ATA connector 7 Peripheral connector 8 I 2 C interface 9 SPI interface 10 Ethernet 2(FPGA) 11 Ethernet 1(EG20T) 12 VGA connector 13 USB 2.0 1/2/3/ Bit ADC 15 8 Bit ADC Bit DAC 17 Mini PCI-e 18 CMOS lithium cell battery 19 Power LED 20 H.D.D. LED 21 Buzzer 22 CAN 2.0B interface 23 Audio line out Description 4

11 No. Description 24 LCD & touch screen assembly connector 25 Audio microphone input 26 Video input 27 Serial port2 28 Serial port1 29 Power input connector 30 PWR_ON button 31 RST button CPU core board layout No. Description 1 Intel IOH EG20T 2 FPGA config device Altera EPCS64 3 Altera FPGA JTAG pin header 4 Intel Atom E546C processor 5 DDR2-800 Memory chips 6 DDR2 Memory chip connected to FPGA 7 NOR flash connected to FPGA 8 XDP port(not available) 9 SF100 port(not available) 5

12 2.2.4 Onboard header pins FPGA JTAG pins Pin No. Signal Pin No. Signal 1 TCK 2 GND 3 TDO 4 VCC 3.3V 5 TMS 6 VCC 3.3V 7 N/C 8 N/C 9 TDI 10 GND LPC (Low Pin Count) Pins 6

13 Pin No. Signal Pin No. Signal 1 VCC 3.3V 2 FRAME_N 3 AD3 4 AD2 5 AD1 6 AD0 7 GND 8 PLTRST 9 CLKOUT0 10 SERIRQ I 2 C Pins Pin No. Signal Pin No. Signal 1 VCC 3.3V 2 N/C 3 N/C 4 SCLK 5 N/C 6 SDATA 7 GND 8 N/C 7

14 SPI Pins Pin No. Signal Pin No. Signal 1 VCC 3.3V 2 VCC 3.3V 3 SCK 4 MISO 5 SSN 6 MOSI 7 GND 8 GND Camera Pins Pin No. Signal Pin No. Signal 1 SCLK 2 SDA 3 CLK 4 DATA7 5 DATA6 6 DATA5 8

15 7 DATA4 8 DATA3 9 DATA2 10 DATA1 11 DATA0 12 GND Onboard button PWR_ON button Press the PWR_ON button after you connect the power cable, the platform will start to POST. RST button Press the RST button the system will restart to POST after the platform is powered on. 9

16 FPGA button There are four buttons connected to the FPGA I/O pins. SW3 SW4 SW5 SW6 Switch FPGA I/O pin 7A_TIO5_LVDS_TX_T12_DP_M 7A_TIO5_LVDS_RD_T11_DP_M 7A_TIO4_LVDS_TX_T13_DP_P 7A_TIO5_LVDS_RD_T11_DP_P Onboard LEDs PWR LED This red LED indicates the power status after the platform is powered on. 10

17 H.D.D LED This green LED indicates the STAT device and CF card status. FPGA LEDs There are eight green LEDs connected to the FPGA I/O pins. D19 D20 D21 D22 D23 D24 D25 D26 LEDs PCB mark FPGA I/O Pin 7A_TIO5_LVDS_TX_T10_DP_M 7A_TIO4_LVDS_RD_T13_DP_M 7A_TIO5_LVDS_TX_T11_DP_P 7A_TIO4_LVDS_RD_T13_DP_P 7A_TIO5_LVDS_TX_T11_DP_M 7A_TIO5_LVDS_RD_T12_DP_M 7A_TIO5_LVDS_TX_T12_DP_P 7A_TIO5_LVDS_RD_T12_DP_P 11

18 LAN port LED indications Activity Link LED Speed LED Status Description Status Description OFF No Link OFF 10 Mbps connection Orange Linked Orange 100 Mbps connection Blinking Data Activity Green 1 Gbps connection The Ethernet by FPGA do not recommend using. This Ethernet has bug with performance How to remove LCD screen If user does not need to use the LCD screen, user can remove it. 1. Ensure the power cable is unplugged. 2. Loosen the four screws that fixed LCD module. 3. Remove the LCD screen module from the base board. 12

19 Capter 3 Building your system 1. Connect SATA power cables to the SATA H.D.D. 2. Connect SATA cable. 3. Connect USB keyboard and mouse. 4. Connect power supply cable to power connector. 5. Press PWR ON button on the right edge of the board. The development platform will start to boot. 6. Board will start to POST. 7. If it is not connected with storage device, the platform will stop on the EFI shell. Show as. Figure 1 8. If connected storage device with OS, input exit command in the EFI shell, platform will start to load OS. 13

20 Capter 4 Other Information 4.1 Where to find Information Intel cup electronic design contest web site: More information for Intel embedded: Technical Support Technical support esdc@zlg.cn Technical support phone: (9:00~17:00 Beijing Time, Mon ~ Fri) Technical support forum: Technical support forum: Intel cup electronic design contest Tencent QQ group: No