Description. Feature. System Application Diagram

Transcription

1 Description AO-FD FD LC LC-MX88 optical matrix bundle with AD-SL-500-4LC to achieve an image routing system, it is definitely saving 50% extenders cost and reducing complicated electrical cables connection. AO-FD FD LC 4LC-MX88 is hardware base design, easy to installation just likes as plug & play, no need any additional driver or software. It also provides LED indicators to display matrix setup status. AO-FD FD LC 4LC-MX88 can be applied on long distance HD video switch and broadcasting, such as medical image system at surgical room, MRT/airport passenger information system, hotel/super market video broadcasting and switch system. In addition, fiber input/output interface fulfilled high quality and interference free communication. Feature Simple and user friendly interface Support RS232 and manually control No EMI issue and interference free Class 1 laser product complies with EN System Application Diagram Application Medical surgical room image system MRT/Airport passenger information system Hotel/Super market video broadcasting system Page 1 of 6

2 Ordering Information Part Number Description Note AO-FD-500-4LC-MX88 8*8 optical matrix Checklist 8*8 Optical Matrix 1 Adaptor 1 This product does not include optical fibers Specification PARAMETER SPECIFICATION NOTE Max. Distance 500 meters 50/125 um MMF Max. Video Resolution Max. Video bandwidth (16:9) (16:10) 2.25 Gbps per channel RS-232 Baud Rate 9600bps N, 8, 1 Supply Voltage DC 5V Power Consumption 20 W 5V/4A Operation Temperature -10 to 50 Storage Temperature -20 to 75 Outline Size (L W H) (mm) 19 2U Rack Mount Weight Kg Page 2 of 6

3 System Requirement DVI source + AD-SL-500-4LC-T DVI sink + AD-SL-500-4LC-R 100~240VAC 50~60Hz 1.7A electricity AC-DC Adaptor Specification PARAMETER SPECIFICATION NOTE Input Voltage 100~240VAC, 50~60 Hz Output Voltage DC 5V Output Current 5A Max. DC Jack Inside +5V, outside ground Page 3 of 6

4 Installation Step 1. Install AD-SL-500-4LC-T close to DVI source Step 2. Install AD-SL-500-4LC-R close to DVI sink Step 3. Connect AD-SL-500-4LC-T to DVI source directly, additional DVI cable is not recommended Step 4. Connect AD-SL-500-4LC-R to DVI sink directly, additional DVI cable is not recommended Step 5. Please follow up sequence number to connect fiber between AD-SL-500-4LC-T and matrix Step 6. Please follow up sequence number to connect fiber between AD-SL-500-4LC-R and matrix Step 7. Power up DVI extender and matrix Step 8.Configure matrix connection through RS-232 command or panel push-button key Remark 1: Please ensure fiber surface clean before insertion, dust may impact communication performance Remark 2:If DVI source +5V capability is enough (>250mA), AD-SL-500-4LC-T doesn t need external PSU. Remark 3:AD-SL-500-4LC-T can clone EDID from monitor if default value is not applicable, refer to AD-SL-500-4LC user guide Remark 4:AD-SL-500-4LC fiber sequence number as following: RX TX Page 4 of 6

5 Panel Push-Button Switch Operation 1. Input key: Press Input key to select input port, 1~8 cycling change as LED indication 2. Output key: Press Output key to select output port, 1~8 cycling change as LED indication 3. Set key: Press Set key more than 3 seconds to connect (1) + (2), LED will flash during matrix connection setup, stop flash after setup done. Matrix configuration result: 8*8 LED to display input/output connection status. RS232 Command Specification Byte 0 : 0xFD, Header Byte 1 : 0x66 Indicate matrix1 type (4LC) Byte 2 (0xBB) : Check matrix table Byte 2 (0xCC) : Turn on matrix, load from EEPROM Byte 2 (0xDD) : Turn off matrix, write to EEPROM Byte 2 (0xAA) : Assign matrix Byte 3 : xxx xxx Indicate output port 1~8 (000~111) Byte 4 (0x02) : Fixed value means xxx connects TO yyy Byte 5 : yyy yyy Indicate input port 1~8 (000~111) Byte 6 : 0xFC, End of packet User scenario 1. Turn on matrix FD 66 CC FC Matrix confirm back FD 66 CC FC 2. Assign matrix FD 66 AA 0x 02 1y FC, Output-x (0~7) assign to Input-y (0~7) 3. Check matrix table FD 66 BB FC Matrix confirm back FD 66 BB FC OP[0]~OP[7], OP[0]~OP[7]: indicate output port connects to which input port 1~8 (000~111) 4. Turn off matrix FD 66 DD FC Matrix confirm back FD 66 DD FC Page 5 of 6

6 Outline Size AO-FD-500-4LC-MX88 All dimensions all in +/- 0.3mm tolerance if no specified Unit:mm Page 6 of 6