INSTALLED SOUND MICROPHONES

Transcription

1 INSTALLED SOUND MICROPHONES CONFERENCE TECHNOLOGY MADE IN GERMANY

2

3 CLASSIS INSTALLED SOUND MICROPHONES GOOD SOUND RIGHT FROM THE START The purpose of a microphone is to convert the sound of the spoken word into an electrical signal. Sound and volume have to be synchronised perfectly, because a bad signal at the beginning of a sound system chain cannot be converted into a good signal anymore. The beyerdynamic installed sound ensure the uncompromising transmission of the spoken word and maximum intelligibility of speech. The versatile product range provides solutions for different applications such as lecterns, panel discussions, meetings, conferences, tele/video conferences and ceiling installations. The Scudio Technology makes microphones immune to interferences from mobile phones The Scudio technology includes many electronical and mechanical measurements to eliminate unwanted interferences from mobile phones. The patented shielding of the capsule is an important detail of all microphones. The interaction of all Scudio features ensures the optimal sound quality and intelligibility of speech of the beyerdynamic installed sound microphones.

4 CLASSIS GOOSENECK MICROPHONES GOOSENECK MICROPHONES The gooseneck microphones of the Classis GM 3xx-series with an extremely small microphone head meet the requirements of design. The thin gooseneck of 6 mm with a mat black, non-glare surface can be discretely integrated into any installation. The cardioid polar pattern of the microphones ensures maximum volume due to a high gain before feedback with excellent intelligibility of speech. The versatile series allows many kinds of application: the use with speaker s desks or altars, the use in conference systems, in studio and sound systems for mixing consoles and the use as stationary microphone in paging systems. Gooseneck microphones with 3-pin XLR connector Classis GM 303 Length 300 mm (12 ), completely flexible gooseneck. Classis GM 305 Length 500 mm (20 ), flexible gooseneck at the top and bottom, rigid tube in the middle. Classis GM 306 Length 600 mm (24 ), flexible gooseneck at the top and bottom, rigid tube in the middle. GM 306 GM 305 GM 303 Gooseneck microphones with externally controlled LED ring and 5-pin male XLR connector Classis GM 315 Length 500 mm (20 ), flexible gooseneck at the top and bottom, rigid tube in the middle. The LED ring is externally controlled via the 5-pin male XLR connector. It signalises, for example, if the microphone is turned on. GM 315 LED ring For beyerdynamic conference systems, the microphones are also offered without preamplifier.

5 CLASSIS GOOSENECK MICROPHONES Gooseneck microphones with LED ring, programmable button and 3-pin XLR male connector Classis GM 313 SP Length 300 mm (12 ), completely flexible gooseneck. Classis GM 315 SP Length 500 mm (20 ), flexible gooseneck at the top and bottom, rigid tube in the middle. GM 315 SP / RC GM 313 SP LED ring By using the programmable button of the SP variants you can select the operating mode ON/OFF, Push-To-Talk or Push-To-Mute. The microphone button can also be completely disabled. Furthermore, there are two settings of the frequency response possible: linear or with bass roll-off to suppress low-frequency noise. The LED ring to display the microphone status can be deactivated. Gooseneck microphone with LED ring, programmable button, remote control and 5-pin XLR male connector Programmable buttons of the SP and RC variants Classis GM 315 RC Length 500 mm (20 ), flexible gooseneck at the top and bottom, rigid tube in the middle. In addition to the features of the SP variants, the RC version allows the operation by an external control. In addition to this an external device can be controlled via the control output when operating the microphone button. Microphone base for different applications The handy microphone base is available in two versions for gooseneck microphones with (5-pin version) or without (3-pin version) an LED ring. The on-off button is backlit to display the status. Standard applications include the use with lecterns, podiums or announcements. In conjunction with a DSP device (Digital Signal Processor) several GMB 35 S 5-pin versions can be used as conference system. Shock-mounted installation holder The shock-mounted installation holder for the Classis GM and RM microphones is available as 3-pin (GMS 32) and 5-pin variant (GMS 52) in black (B) or white (W). The removable lid covers the holder when the microphone is not in use. On request it can be produced in individual colours to match the surface of the table visually.

6 CLASSIS GOOSENECK MICROPHONES T-Version with smart accessories for different applications The T-version features extensive mounting accessories. Depending on the application the microphone can be mounted on a stand, tabletop or speaker s desk. Classis GM 305 T Length 500 mm (20 ), flexible gooseneck on top and bottom, rigid tube in the middle, external M18 x 0.75 thread, connecting cable 2.5 m with 4-pin female mini XLR socket, incl. CVE power supply, cover cap and ZSH 305 base plate. Detailed mounting accessories Stand mounting Cover cap with 5/8 internal thread incl. 3/8 adapter for stand mounting (supplied accessory). Base plate ZSH 305 base plate for permanent installation on tables, speaker s desks etc. (supplied accessory). Low frequency isolation ZSA 305 mounting adapter for ZSH 20 holder with low frequency isolation, cable outlet at the bottom (optional accessory). Wireless gooseneck microphone You can use the GM 305 T gooseneck microphone in wireless applications when flexibility is required for example for speaker s desks. The connecting cable can be connected to the beltpack transmitters of the Opus and Synexis wireless series. The microphone is then powered by the beltpack transmitter.

7 CLASSIS GOOSENECK MICROPHONES Gooseneck microphones entry series The gooseneck microphones of the Classis GM 1xx series feature a cardioid polar pattern with a high gain before feedback. The microphones with a matt black, non-glare surface and 6 mm thin gooseneck discretely blend into each environment. They can be used for example on lecterns. Classis GM 105 Length 500 mm, top and bottom gooseneck, rigid tube in the middle, 3-pin XLR male connector. GM 105 GM 115 LED ring GM 115 Classis GM 115 Length 500 mm, top and bottom gooseneck, rigid tube in the middle, LED ring, 5-pin XLR male connector. Miniature microphone Classis GM 301 Miniature gooseneck microphone GM , length 100 mm (4 ), 4-pin female mini XLR connector, CVE preamp and blind cover. The microphone can be connected via the 4-pin female mini XLR connector to the CVE power supply, which also serves as mounting holder with low frequency isolation. When the microphone is not connected, the connection can be protected by using the cover cap. The microphone is used for example in video conferences. Blind cover Wireless solution For lecture hall applications there is an easy to handle solution when the GM microphone is used with a beltpack transmitter of the Opus or Synexis wireless series. When stored in the charger the set will always be ready for use and when needed, it can be placed in the breast pocket of the speaker.

8 CLASSIS BOUNDARY MICROPHONES BOUNDARY MICROPHONES Classis BM 42 / 43 Boundary Microphones The Classis BM 42 / 43 series consists of small, discreet condenser boundary microphones. The balanced frequency response and the discreet design provide a variety of applications: The microphones can be used for discussions, tele-/video conferences or live and theatre applications. BM 42 / 43 B / BC Classis BM 42 B / W / BC The half-cardioid polar pattern increases the gain before feedback and reduces the diffuse room noise. Available in black (B) and white (W) with bare-ended connecting cable and in black with XLR male connector (BC). BM 42 / 43 W Classis BM 43 B / W / BC Half-spherical polar pattern: The high sensitivity results in a sufficient output level even when miking from a distance. Available in black (B) and white (W) with bare-ended connecting cable and in black with XLR male connector (BC). Classis BM 52 Boundary Microphone The Classis BM 52 boundary microphone combines a number of different functions in a small, discreet housing. Depending on the application there are three operating modes you can select: ON-OFF, Push-To-Talk and Push-To-Mute. Furthermore, the frequency response can be set in three stages: linear or a two-stage roll-off filter to compensate low-frequency noise. The Classis BM 52 is operated via a silent membrane key with Braille and a super bright LED displays the ready-to-speak status. It is ideal for discussions or tele/video conferencing. The Classis BM 52 RC provides the additional feature of an external operator use or the microphone itself can send a control command. Both models are fitted with a mini XLR connection. BM 52 / 52 RC Classis BM 52 Half-cardioid polar pattern, including cable with 3-pin male XLR connector. Classis BM 52 RC Half-cardiod polar pattern, including cable with 5-pin male XLR connector. Remote control possible.

9 CLASSIS BOUNDARY MICROPHONES MPC 70 USB Boundary Microphone MPC 70 USB Half-spherical polar pattern, connection cable with USB connector type B, 3 m long. The MPC 70 USB microphone is suitable for the connection to computers and laptops. Depending on the application you can choose between the operating modes ON-OFF, Push-To-Talk and Push-To-Mute. Furthermore, the frequency response can be set in two stages: linear or roll-off filter to compensate low-frequency noise. The switchable gain compensates loud or quiet speakers or small or big distances between microphone and speaker. It is ideal for the audio recording of conferences and meetings with a maximum of 10 participants or for web conferences and discussions. Conference and Recording If meetings are to be recorded, the steno-s conference and recording software is ideal to complement the MPC 70 USB boundary microphone. With just one mouse click steno-s will easily record all discussions on a PC during your meeting. More informationen Quinta TB Wireless Boundary Microphones Due to its high degree of flexibility and reliability the wireless Quinta TB boundary microphone is suitable for small meeting rooms, huddle rooms or video conferencing. Quinta TB Wireless boundary microphone, including power adapter for charging or operation. Pictured with optional charger. Quinta CU The control unit provides flexible configuration and numerous interfaces. The proven triple band technology of the Quinta family ensures the wireless transmission. The privacy is guaranteed by a 128-bit encryption and a 24-bit PIN code. The multi-channel receiver features a long operating time of 14h at minimum and a short charging time. Different operating modes can be selected via the software. In the Microphone mode, Quinta CU acts as a multi-channel receiver in which a maximum of four Quinta TB can be operated simultaneously. In this mode several control units can be connected via the software. In the Conference mode, the Quinta TB acts as a delegate unit and can therefore be used for any conventional conferencing application.

10 CLASSIS BOUNDARY MICROPHONES Installation Boundary Microphones The discrete, almost invisible microphones for installations into tables or ceilings integrate into different materials and surfaces in the colours black (B), white (W) and silver (SE). Elastic rings achieve an efficient attenuation of unwanted mechanical vibration. They are connected via a 3-pin male XLR connector. The microphones are used in tele/video conferences, discussion rounds, for room monitoring or level measurement. Classis BM 32 B / W / SE Boundary microphone (semi-cardioid), recommended for table installation. The semi-cardioid polar pattern pointing forward and upwards increases the gain before feedback and reduces the amount of diffuse room sound. BM 32 / 34 B BM 32 / 34 W BM 32 / 34 SE For beyerdynamic conference systems the BM 32 E (black) is offered without preamp. Classis BM 33 B / W / SE Semi-spherical polar pattern, recommended for installations into ceilings or tables. The high sensitivity ensures a sufficient output level even when the distance is big. BM 33 B BM 33 W BM 33 SE Classis BM 34 B / W / SE Semi-cardioid polar pattern, with bass roll-off, recommended for table installation. Integrated filter to reduce lowfrequent mechanical vibration (picture as BM 32). BM 32 / 34 table installation with BMR BMR LED ring The BMR LED ring is an accessory for all Classis boundary microphones. It is used to indicate the status in tele or video conferences and illuminates in different colours. The BMR LED ring is controlled via a media control system, the logic output of a DSP mixer or a video conference system.

11 CLASSIS OVERHEAD MICROPHONES OVERHEAD MICROPHONES The miniature microphones for permanent or hanging installations to ceilings allow almost invisible solutions. The short, flexible gooseneck allows an optimal positioning to the speaker and precise recording. The Classis OM microphones are used for ceiling installations in conference rooms, in tele/video conferences, in training rooms with distance learning or as ambiance microphones. OM 302 US OM 304 US OM 302 OM 304 Cable length can be up to 8 m (26.2 ft) Classis OM 302 Supercardioid polar pattern, for permanent installations into ceilings with standard installation sockets. Classis OM 304 Supercardioid polar pattern, for hanging installations into ceilings with standard installation sockets. The thin 8 m (26,2 ft) long twist-safe cable can be shortened and allows a discrete positioning of the microphone in any height. Another option to clear the table from technology and to pick up several people with a microphone are the beyerdynamic boundary microphones for installations and microphones with Revoluto technology. They are used, for example, for video conferencing. When installing microphones to a ceiling, you should note in general that due to the large distance between microphone and speaker more ambient noise is picked up. Therefore, when installing the microphones, room acoustics and noise sources have to be taken into account. Classis BM 33 boundary microphone MPR 210 W Revoluto array microphone Classis RM 30 W Revoluto array microphone with GMS 32 W installation holder

12 REVOLUTO ARRAY MICROPHONES MICROPHONES WITH REVOLUTO TECHNOLOGY The Revoluto principle is based on patented microphone array technology, where microphone capsules are arranged in either a horizontal or vertical row. Compared to gooseneck microphones this creates a much greater distance for voice pick up. As a result, the speaker is not restricted to the typical pick up pattern or usual compact speaking distance offered by most gooseneck microphones and therefore does not need to concentrate on talking directly into the microphone. The speaker has maximum freedom of movement with a consistent intelligibility of speech. More information and video clips: Recording area of a gooseneck microphone compared to a horizontal and vertical array microphone. The horizontal and vertical arrangements of the microphone arrays differentiate in design as well as in the alignment of the corridor characteristic, which is displayed above. Horizontal Array Microphone MPR 210 / 211 MPR 210 W The desktop microphones with horizontal microphone array have a vertical corridor characteristic. They are used for panel discussions, conferences, meetings, tele/video conferences and for ceiling mounting. MPR 210 B MPR 210 B / W Horizontal array microphone, available in black (B) and white (W). MPR 211 B MPR 211 B Horizontal array microphone with LED strips to display the microphone status. Optionally the microphone button can be operated or disabled. Via the control output an external device can be controlled when operating the microphone button. At the bottom of the microphone the operating mode ON/OFF, Push-To-Talk or Push-To-Mute can be selected. Furthermore, it can be operated via an external switching contact (operator service).

13 REVOLUTO ARRAY MICROPHONES Enhanced freedom of movement: Whether the speaker is sitting or standing, the volume and audio quality always remain the same. Whether close to the microphone or leaning backwards sound deviations due to different distances are minimised. No fading in and out when you move your head to the left or right. Optimal voice recording with a discreet mounting to the ceiling, ambient noise is minimised. Vertical Classis RM 30 / 31 Array Microphone The desktop microphones with horizontal microphone array have a vertical corridor characteristic. They are used for panel discussions, conferences, meetings, tele/video conferences and for ceiling mounting. Classis RM 30 B / W Desktop microphone with Revoluto technology, available in black (B) and white (W). Classis RM 31 SP Vertical array microphone with an LED ring to display the microphone status. By using the programmable button it is possible to select between the operating modes ON/OFF, Push-To-Talk and Push-To-Mute. The microphone button can also be completely disabled. Furthermore, there are two settings of the frequency response possible: linear or with bass roll-off to suppress low-frequency noise. The LED ring to display the microphone status can be deactivated. RM 30 B RM 30 W RM 31 SP / RC Classis RM 31 RC Vertical array microphone with an LED ring to display the microphone status. In addition to the features of the SP variants, the RC version allows the operation by an external control. In addition to this an external device can be controlled via the control output when operating the microphone button. Maximum freedom of movement to the right and left without large volume fluctuations, limited the recording of signals and noises from the ceiling and table. Whether close to the microphone or leaning backwards sound deviations due to different distances are minimised. No fading in and out when you move your head to the left or right. Two or more people can share one microphone.

14 OVERVIEW INSTALLED SOUND MICROPHONES Model Order # Polar pattern Connection Switch Illuminated ring Colour More Classis GM cardiod 3-pin XLR black length 500 mm Classis GM cardiod 5-pin XLR yes black length 500 mm Classis GM supercardiod 4-pin female mini XLR black length 100 mm, incl. power supply Gooseneck microphones Installation boundary microphones Desktop boundary microphones Overhead microphones Revoluto array microphones Classis GM supercardiod 4-pin female mini XLR black length 100 mm Classis GM cardiod 3-pin XLR black length 300 mm Classis GM cardiod 3-pin XLR black length 500 mm Classis GM 305 T cardiod 5/8 or 3/8" internal thread black length 500 mm, incl. base plate Classis GM cardiod 3-pin XLR black length 600 mm Classis GM 313 SP cardiod 3-pin XLR yes yes black length 300 mm Classis GM cardiod 5-pin XLR yes black length 500 mm Classis GM 315 SP cardiod 3-pin XLR yes yes black length 500 mm Classis GM 315 RC cardiod 5-pin XLR yes yes black remotely controllable Classis BM 32 B semi-cardiod 3-pin XLR BMR optional black Classis BM 32 W semi-cardiod 3-pin XLR BMR optional white Classis BM 32 SE semi-cardiod 3-pin XLR BMR optional silver Classis BM 33 B semi-spherical 3-pin XLR BMR optional black Classis BM 33 W semi-spherical 3-pin XLR BMR optional white Classis BM 33 SE semi-spherical 3-pin XLR BMR optional silver Classis BM 34 B semi-cardiod 3-pin XLR BMR optional black bass roll-off Classis BM 34 W semi-cardiod 3-pin XLR BMR optional white bass roll-off Classis BM 34 SE semi-cardiod 3-pin XLR BMR optional silver bass roll-off Classis BM 42 B semi-cardiod bare ends black Classis BM 42 BC semi-cardiod 3-pin XLR black Classis BM 42 W semi-cardiod bare ends white Classis BM 43 B semi-spherical bare ends black Classis BM 43 BC semi-spherical 3-pin XLR black Classis BM 43 W semi-spherical bare ends white Classis BM semi-cardiod mini XLR + cable 3-pin XLR yes black Classis BM 52 RC semi-cardiod mini XLR + cable 5-pin XLR yes black remotely controllable MPC 70 USB semi-spherical USB, Type B yes black Quinta TB semi-cardiod wireless yes black Quinta CU control unit needed Classis OM supercardiod installation socket white US version: Order # Classis OM supercardiod installation socket, 8 m cable white US version: Order # Classis RM 30 * corridor vertical 3-pin XLR black Classis RM 30 W * corridor vertical 3-pin XLR white Classis RM 31 SP * corridor vertical 3-pin XLR yes yes black Classis RM 31 RC * corridor vertical 5-pin XLR yes yes black remotely controllable MPR 210 B * corridor horizontal 3-pin XLR black MPR 210 W * corridor horizontal 3-pin XLR white MPR 211 B * corridor horizontal bare ends yes yes black controlled by a microcontroller * Please refer to the data sheet for details on phantom powering

15 INSTALLED SOUND MICROPHONES APPLICATIONS Lectern Altar / Pulpit / Ambo Panel discussion / Press conference Application on stands Small meetings (recording) (1 microphone for several participants) Large meeting (with audio DSP) Applications on the armrests of a chair Video conferencing / sound system in the room (1 microphone per participant) Video conferencing / no sound system in the room (1 microphone for several participants) Video conferencing ceiling installation, no system in the room (1 microphone for several participants) Ceiling microphone Distance learning Paging Room surveillance Small theatre stages Voice recording Ambiance microphone for picking up the atmosphere Web conference / PC applications Direct connection to a beltpack transmitter Classis GM x x x XLR x x x Classis GM x XLR x x x Classis GM x Classis GM x Classis GM x x XLR Classis GM x x XLR x Classis GM 305 T x x 3/8 x Classis GM x x XLR x Classis GM 313 SP x x x XLR x x x Classis GM XLR x Classis GM 315 SP x x x XLR x x x x Classis GM 315 RC x x Classis BM 32 B x x Classis BM 32 W x x Classis BM 32 SE x x Classis BM 33 B x x x x x x x Classis BM 33 W x x x x x x x Classis BM 33 SE x x x x x x x Classis BM 34 B x Classis BM 34 W x Classis BM 34 SE x Classis BM 42 B x x x Classis BM 42 BC x x x Classis BM 42 W x x x Classis BM 43 B x x Classis BM 43 BC x x Classis BM 43 W x x Classis BM x Classis BM 52 RC x x MPC 70 USB x x x Quinta TB x x Classis OM x x x x x Classis OM x x x x x x Classis RM x XLR x x x x x x Classis RM 30 W x XLR x x x x x x Classis RM 31 SP x Classis RM 31 RC x x MPR 210 B x 3/8 x x x x x MPR 210 W x 3/8 x x x x x MPR 211 B x 3/8 x x This overview is a recommendation and should serve as a decisive measure. The microphones, however, can be used as desired.

16 INSTALLED SOUND MICROPHONES ACCESSORIES ACCESSORIES ST 600 (Order # ) Microphone stand with heavy foot, 3/8 thread, adjustable height m ZSH 210 (Order # ) Stand mount for MPR 210/211 microphones, 5/8 thread, 3/8 adapter, mat black GMS 32 (Order # ) Shock-mounted installation holder for Classis GM and RM microphones with 3-pin XLR male connector, in black or white (GMS 32 w, ) GMS 52 (Order # ) Shock-mounted installation holder for Classis GM and RM microphones with 5-pin XLR male connector, in black or white (GMS 52 w, ) ZSH 20 (Order # ) Elastic holder for gooseneck microphones with male XLR connector, flush-mount, black, with counter nut ZSA 305 (Order # ) Mounting adapter for GM 305 T, suitable for ZSH 20 holder GMB 33 S (Order # ) Microphone base with 3-pin female XLR connector for gooseneck microphones and 3-pin male connector at the rear of the housing, on-off button backlit GMB 35 S (Order # ) Microphone base with 5-pin female XLR connector for gooseneck microphones with LED ring and 5-pin male connector with logic inputs and outputs at the rear of the housing, on-off button backlit BMR (Order # ) RGB indication ring for Classis BM / MPC series installation boundary microphones, including mounting kit Quinta CB (Order # ) Charger for wireless Quinta TB boundary microphone, integrated magnets to connect several chargers mechanically Coretis (Order # ) Digital signal processor (DSP) for processing, mixing and distribution of audio signals steno-s 4 Conference (Order # ) Recording and logging software for meetings beyerdynamic GmbH & Co. KG. Theresienstr Heilbronn. Germany. Phone Fax AudioSystems@beyerdynamic.de beyerdynamic Inc. USA. 56 Central Ave. Farmingdale, NY Phone Fax salesusa@beyerdynamic-usa.com Installed Sound Microphones ( ) Non-contractual illustrations. Subject to change without notice