Product Specification

Transcription

1 SD12004 PATA 2.5inch 9.5mm Industrial SSD Product Specification LinkedHope Intelligent Technologies Co,.Ltd

2 Table of Contents 1. General Description Key Features Physical Dimension Product Specification Interface Capacity Performance Data Transfer Rate IOPS Access Time Reliability Wear-Leveling ECC Endurance Data Retention MTBF Bad block management Power Lose Protection Electrical Specification Supported Standards Master / Slave Setting Configuration Pin Assignment Reserved Pins Power Voltage Power Consumption Supported ATA commands Optional Supported Limitation Environmental Specification Temperature Humidity Shock

3 6.4 Vibration Altitude Regulation Compliance Ordering Number

4 1. General Description LinkedHope SD12004 Industrial SSD employs proprietary SSD controller and flash management technology to deliver reliable and stable performance to users in industrial and embedded fields. LinkedHope W80 leading edge flash controller and proprietary flash mapping algorithm provide stable and balanced performance output by taking both sequential and random data transaction into consideration, and no performance degradation over long operating hours in real world operations. SD12004 product embed full data protection including proprietary set of algorithms and dedicated hardware circuits which capable of protecting data anywhere within the SSD from cache to flash against power fail and other unexpected events in fields application. 2. Key Features 2.5inch 9.5mm height Form Factor with a 44-pin PATA connector ATA interface support UDMA-6 Support Master/Slave operation, support 2 devices in one ATA bus Support ATA command set ATA-8 ACS2 Wide capacity range to meet actual application 2G, 4G, 8G, 16G, 32G, 64G, 128G, 256G, 512G Industrial temperature range(-40 ~ +85 ) and conformal coating option available for hash environment Fast data purge, Access control option available for data security Specially designed hardware and firmware to protect user data integrity during emergency power lose Advanced static, dynamic and active wear-leveling algorithm Self-healing technology, automatic detect and correct hidden error bit No internal copy back operation, no ECC accumulation Build-in 16bits/sector ECC Real time background Garbage-Collection, no performance degrade Advanced bad block management 90nm controller process, very lower power consumption S.M.A.R.T support ATA Security Commands Set Support Optional FW-based application extensions data purge, write protection and partition recovery Support 5x, 4x, 3x, 2x nm NAND flash memory, support 2KB, 4KB, 8KB page size, support SLC and MLC flash media 4

5 3. Physical Dimension Parameters Value Unit Length (+/-0.3) mm Width 69.8 (+/-0.3) mm Height 9.5 (+/-0.3) mm Weigh 90 (Max.) g * AL-Alloy metal enclosure to meet industrial requirements 4. Product Specification 4.1 Interface This module complies with the ATA-8 standard published by ANSI and support ATA-8 ACS-2 command set. Supported PATA transfer mode: PIO Mode 0 to 4 Multiword DMA0,1,2 UDMA Mode 0 to Capacity 4k page size NAND FLASH Capacity(GB) Unformatted* Cylinders Head Sector Total Number of User-Addressable Sectors in LBA Mode 2G ,686,392 4G ,372,792 5

6 8GB ,745,592 16GB ,491,192 32GB ,982,392 64GB ,964, GB ,929, GB ,859, GB ,718,392 8k page size NAND FLASH Capacity(GB) Unformatted* Cylinders Head Sector Total Number of User-Addressable Sectors in LBA Mode 2G 1.8G G 3.7G GB 7.5G GB 15.1G GB 30.1G GB 60.3G GB 120.7G GB 241.5G GB 483.1G SLC Drive Capacity Range : 2G 256G MLC Drive Capacity Range : 4G 512G * the unformatted capacity data were tested by CrystalDsikInfo Performance LinkedHope W80 leading edge flash controller and proprietary flash mapping algorithm provide stable and balanced performance output by taking both sequential and random data transaction into consideration, and no performance degradation over long operating hours in real world operations. The performance data is variant depend on the flash media and capacity. There are some general rules: SLC will faster than MLC; High capacity will faster than low capacity at write performance; Advanced process of Flash will have advantage in cost, but will have disadvantage in performance and endurance; Higher write throughput will consume more power when use same Flash media; SLC will consume less power than MLC at same write throughput; We list some typical configuration for reference Data Transfer Rate SLC FLASH Channel Sequential Read Up to Sequential Write Up to 2G 1ch MB/S Unit 4G 2ch MB/S 8G above 4ch MB/S 6

7 MLC FLASH Channel Sequential Read Up to Sequential Write Up to 4G 1ch 30 6 MB/S Unit 8G 2ch MB/S 16G 4ch MB/S 32G above 4ch MB/S Test Setup : Intel E G DDRS + ASUS P5BSE Main Board OS: Windows XP SP2 Benchmarking Software: HD Tach 3.01 RW IOPS Mode IOPS ( IO operation per second ) Sustained SLC / MLC 100% Random Read 4K 3000 / % Random Write 4K 1000 / 500 Test Setup : Intel Core Due E G DDRS + ASUS P5BSE Main Board OS: Windows XP SP2 Benchmarking software: IO Meter Access Time Random access time : 0.3msec Test Setup : Intel Core Due E G DDRS + ASUS P5BSE Main Board OS: Windows XP SP2 Benchmarking software: HD TACH Reliability Wear-Leveling LinkedHope LHIW Series SSD applies Static, Dynamic and Active wear leveling algorithms to endure the NAND flash memory blocks under same wearing level ECC Building ECC ( Error Correction Code ) correct 16bits per 528 Bytes Endurance The NAND flash has limited Program/Erase cycle limitation, but has unlimited on read operations. The endurance major rest with host s writing intensity. 7

8 The write endurance is variant depend on the flash media, capacity and host access pattern. There are some general rules: SLC last longer than MLC; High capacity last longer than low capacity; Sequential data last longer than random data; Boundary aligned data(4kb, 8KB, 16KB ) last longer than unaligned data; \ 2G 4G 8G 16G 32G 64G 128G 256G 512G Read unlimited unlimited unlimited unlimited unlimited unlimited unlimited unlimited unlimited Write MLC Write SLC N/A 60G/day 8G/day 80G/day 10G/day 100G/day 30G/day 300G/day 50G/day 500G/day 50G/day 500G/day 50G/day 500G/day 50G/day 500G/day 50G/day N/A Data Retention MTBF Data retention above 10 25C The MTBF (Mean Time Between Failure) is estimated using a prediction methodology based in accordance with the Telcordia Special Report SR- 332 issue 1. The prediction is based on a parts stress analysis. MTBF (Mean Time Between Failure) > 2,000,000 Hours Bad block management Embedded advanced bad block management can replace the bad blocks with reserved blocks available automatically Power Lose Protection On-board back-up power units are provided, it works with special designed FW and hardware circuits to protect user data integrity during emergency power lose 5. Electrical Specification 5.1 Supported Standards 8

9 This module complies with ANSI AT Attachment 8 ATA/ATAPI Parallel Transport (ATA8-APT) Annex B Signal Integrity and UDMA Implementation Guide. 5.2 Master / Slave Setting Configuration 5.3 Pin Assignment Pin No. Signal Definition Pin No. Signal Definition 1 -RESET 2 GND 3 DD7 4 DD8 5 DD6 6 DD9 7 DD5 8 DD10 9 DD4 10 DD11 11 DD3 12 DD12 13 DD2 14 DD13 15 DD1 16 DD14 17 DD0 18 DD15 19 GND 20 removed 21 DMARQ 22 GND 23 -DIOW:STOP 24 GND 25 -DIOR:HDMARDY:# 26 GND 27 IORDY:DDMARDY:DSTORBE 28 -CSEL 29 -DMACK 30 GND 31 INTRQ 32 -LOCS16 33 DA1 34 -PDIAG:CBLID 35 DA0 36 DA2 37 -CS0 38 -CS1 39 -DASP 40 GND 41 +5V 42 +5V 43 GND 44 NC 5.4 Reserved Pins Pin A Reserved for Option FUNC Pin C Reserved for Option FUNC Pin B Reserved for Option FUNC Pin D Reserved for Option FUNC Those pins are reserved for optional function use only, Please check part number and related function operation manual for details. 5.5 Power Voltage 9

10 Parameter Specifications Input Voltage DC 5.0V ± 5% Maximum Ripple 70mV (peak to peak), 0~ 20MHz Maximum Supply Rise Time 100 ms Maximum Supply Fall Time 3 sec 5.6 Power Consumption Status Power Consumption SLC / MLC Typical Idle / Stand-by 30mA / 30mA ma Sequential Read 70mA / 70mA ma Unit Sequential Write 110mA / 160mA ma 5.7 Supported ATA commands The following table lists ATA-standard commands supported by SWRP25 drive. For a detailed description of the ATA commands, refer to the ATA-8 ACS-2 Standads Optional Supported Security and Trim commands sets are supported, but we set them as optional and excluded them in default factory FW setting, if needed the features will be supported and open by users requirements through ordering process Limitation For those optional commands which were listed in ATA-8 standards, please contact LinkedHope technical supports to confirm. Command Name NOP Reset Recalibrate Read Sector(s) Write Sector(s) Read Verify Sector(s) Seek Execute Device Diagnostic Initialize Device Parameters Read Multiple Write Multiple Set Multiple Mode Read DMA Write DMA Flush Cache Command Code (in hex) ATA-standard commands 00h 08h 10h 20h, 21h 30h, 31h 40h 70h 90h 91h C4h C5h C6h C8h CAh E7h 10

11 Identify Device Set Features Check Power Mode Sleep Standby Immediate Idle Immediate Standby Idle Read Sector(s) EXT Read DMA EXT Read Multiple EXT Write Sector(s) EXT Write DMA EXT Write DMA FUA EXT Write Multiple EXT Write Multiple FUA EXT Read Verify Sector(s) EXT Flush Cache EXT SMART DISABLE OPERATIONS SMART ENABLE OPERATIONS SMART ENABLE/DISABLE ATTRIBUTE AUTOSAVE SMART READ ATTRIBUTE THRESHOLD SMART READ DATA SMART RETURN STATUS ECh EFh ATA-standard power-management commands ATA 48bit address commands S.M.A.R.T. commands Security features set(optional) Security Set Password Security Unlock Security Erase Prepare Security Erase Unit Security Freeze Lock Security Disable Password Data Set Management Trim(optional) 98h, E5h E6h E0h 95h, E1h E2h 97h, E3h 24h 25h 29h 34h 35h 3Dh 39h CEh 42h EAh B0h-D9h B0h-D8h B0h-D2h B0h-D1h B0h-D0h B0h-DAh F1h F2h F3h F4h F5h F6h 06H 6. Environmental Specification 6.1 Temperature Temperature Range Unit Commercial C 0-70 Degree C Extended T Degree C Industrial I Degree C Non-Operating Degree C 6.2 Humidity Parameter Humidity Unit 11

12 Operating 85% RH, 85C, 1000Hrs % 6.3 Shock Parameter Force Unit Operating 1.5G Peak,0.5ms,5 times G 6.4 Vibration Status Parameter Unit Operating 20G Peak 20-2KHz G 6.5 Altitude Status Parameter Unit Operating feet 7. Regulation Compliance 8. Ordering Number LHIW P25 M T F x x x G LHIWP25 = LinkedHope W80 PATA 2.5inch 9.5mm Industrial SSD ( Fixed ) Media: Flash Type Used M = MLC S = SLC T : Operating Temperature Range C = Commercial ( 0-70 ) T = Extended ( ) I = Industrial ( ) F: Function Option N = Standard Function S = Security D = Data Purge R = Partition Recovery XXX: Capacity 08 = 8GB 12

13 016 = 16GB 032 = 32GB 064 = 64GB 128 = 128GB 256 = 256GB INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO LinkedHope PRODUCTS, AND IS SUBJECT TO CHANGE WITHOUT NOTICE. NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IN LinkedHope PRODUCTS OR TECHNOLOGY. ALL INFORMATION IN THIS DOCUMENT IS PROVIDED ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND. 1. For updates or additional information about LinkedHope products, contact your nearest LinkedHope office. 2. LinkedHope products are not intended for use in life support, critical care, medical, safety equipment, or similar applications where products failure could result in loss of life or personal or physical harm, or any military or defense application, or any governmental procurement to which special terms or provisions may apply. * LinkedHope reserves the right to change products or specification without notice. Copyright Notice: Copyright 2011 by LinkedHope. All rights reserved. Information contained in this document, including but not limited to any instructions, descriptions and product specifications, is proprietary to LinkedHope. and shall not be modified, used, copied, reproduced or disclosed in whole or in part, in any form or by any means, electronic or mechanical, for any purpose, without the written consent of LinkedHope 13