USER S MANUAL. M16 POKEYS MOTION MOTHERBOARD Rev. 1.1 JUNE 2016.
|
|
|
- Sheena Harrell
- 5 years ago
- Views:
Transcription
1 USER S MANUAL M16 POKEYS MOTION MOTHERBOARD Rev. 1.1 JUNE 2016.
2 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 OVERVIEW FEATURES BOARD DESCRIPTION SPECIFICATIONS Power Requirements POWER TERMINALS AND CONFIGURATION JUMPERS Power Terminal Input terminals Output terminals SELECT JUMPER FOR POKEYS TERMINAL E-STOP CONNECTING A PENDANT Pinout Pendant PINOUT AXIS SAFETY CHARGE PUMP "SCHP" Selecting the SCHP operation mode RJ45 FOR VFD CONNECTION VFD Connection and configuration jumpers PINOUT LPT 3 (EXPANSION) Pin Numbering PINOUT PoExtension PINOUT FOR ENCODER PINOUT limit PINOUT FOR BOARD DIMENSIONS User s Manual Page 0
3 1.0 OVERVIEW This card is a motherboard for the Pokeys57U and PoKeys57E Core Boards. It provides easy integration to breakout boards and with the new pin out of the Pokeys, will control 5 axes, has different types of I/Os and features. 2.0 FEATURES Expansion port (LPT 3) An port to connect Pendant Connector special of 10 pins (PoExtension OUTPUT) 3 Terminals of input 2 Terminals of output Built-in PWM-Based Speed Control. RJ45 Connector for Easy VFD Connection. Can enable and disable the drives. RJ45 connectors for the axis. Power terminal (5VDC). Status LEDs on all inputs and output connections. Microcontroller based SCHP. Outputs +5VDC at 24mA TTL. Two Built-in Electromechanical Relays with NO and NC positions for spindle Control. User s Manual Page 1
4 3.0 BOARD DESCRIPTION 4.0 SPECIFICATIONS 4.1 Power Requirements is required to power this board. WARNING Check the polarity and voltage of the external power source and connect the 5VDC and GND. Overvoltage or reverse-polarity power applied to these terminals can cause damage to the board, and/or the power source. User s Manual Page 2
5 5.0 POWER TERMINALS AND CONFIGURATION JUMPERS 5.1 Power Terminal This input requires an external power if not using the board to supply power to external devices. 5.2 Input terminals These terminals support signals 3.3VDC to 5VDC User s Manual Page 3
6 5.3 Output terminals These terminals provide an output buffered 24mA 6.0 SELECT JUMPER FOR POKEYS When connect the POKEYS ETHERNET, set jumper as show in the image. User s Manual Page 4
7 When connect the POKEYS USB, set jumper as show in the image. 7.0 TERMINAL E-STOP Connect an E-STOP push button as is shown in the below images. User s Manual Page 5
8 8.0 CONNECTING A PENDANT Set the pendant enable jumper in ENABLE position if a pendant is connected to the PIN HEADER connector. If not connects a pendant, set jumper on 2-3. User s Manual Page 6
9 IDC Pinout Pendant IDC26 PENDANT PIN IDC 26 Function Pokeys Pin 1 5V - 2 5V - 3 GND - 4 E-STOP - 5 Fast enc A1 PK1 6 5V - 7 Fast enc B1 PK2 8 GND - 9 LED PK21 10 Axis B switch PK3 11 GND - 12 Axis C switch PK4 13 Axis X switch PK Axis Y switch PK Axis Z switch PK Axis A switch PK X1 switch PK X10 switch PK X100 switch PK User s Manual Page 7
10 9.0 PINOUT AXIS RJ45 Distribution RJ45 (AXIS) PIN RJ45 Pokeys Function 1 NOT USED 2 STEP 3 NOT USED 4 GND 5 ERR 6 DIR 7 NOT USED 8 5V User s Manual Page 8
11 10.0 SAFETY CHARGE PUMP "SCHP". This card lets you use this signal to work as an On/Off switch for your system, enabling a powerful safety system for your equipment. When Status LED, (Green LED) lights, it indicates that the system is enabled. This function is assigned to the pin 53 of the Pokeys User s Manual Page 9
12 10.1 Selecting the SCHP operation mode The Safety Charge Pump can be activated or deactivated depending on the jumper position. 1-2: ON 2-3: OFF User s Manual Page 10
13 11.0 RJ45 FOR VFD CONNECTION This RJ45 port let you make an easy connection between this board and the VFD. RJ45 for VFD RJ45 PIN Function 1 Analog GND 2 Analog Output 3 NOT USED 4 REL 1 Normally Open Contact 5 GND VFD 6 REL 2 Normally Open Contact 7 Ext. 12VDC or 24VDC 8 Relay Common Analog GND: Ground of the Analog output signal Analog Output: Isolated Analog Output Signal (0-10V) GND VFD: Ground of VFD when it is powered with external source of 24V Ext. 12VDC or 24VDC: External 12VDC or 24VDC power supply used to enable the VFD. Relay Common: The signal or voltage wired to this terminal can be connected to the common terminals of the relay 1 and relay 2. User s Manual Page 11
14 11.1 VFD Connection and configuration jumpers Operation Mode Selection Jumper This jumper allows selecting the way how the relays are activated when a PWM signal and REV signal are present in the pins 18 and 43. In US mode one relay is used to start on CW and the other one to start on CCW. In international mode one relay is used for on/off, and the other one to indicate the CW or CCW rotation of the spindle motor. This board uses the step and direction setting for the spindle motor under motor output in Mach4 to generate the required action on the relays. For both cases the presence of PWM will indicate spindle start. User s Manual Page 12
15 See the tables and image below. US MODE (US) PIN RELAYS REL 1 REL 2 OPERATION PWM 1 OFF ON Spindle ON CCW PWM 0 ON OFF Spindle ON CW 0 1 OFF OFF Spindle Off 0 0 OFF OFF Spindle Off INTERNATIONAL MODE (INT) PIN RELAYS REL 1 REL 2 OPERATION PWM 1 ON ON Spindle ON CCW PWM 0 ON OFF Spindle ON CW 0 1 OFF OFF Spindle Off 0 0 OFF OFF Spindle Off User s Manual Page 13
16 12.0 PINOUT LPT 3 (EXPANSION) 12.1 Pin Numbering 26 Pin LPT 3 (EXPANSION) PIN Pokeys Pin 1 PK32 2 PK20 3 PK48 4 PK44 5 PK47 6 PK55 7 PK33 8 PK49 9 PK39 10 GND 11 PK50 12 GND GND 15 PK40 16 GND 17 PK46 18 GND 19 PK54 20 GND 21 PK41 22 GND 23 PK42 24 GND V User s Manual Page 14
17 13.0 PINOUT POEXTENSION Connect special of 10 pins (PoExtension) (PoExtension PINOUT) Equivalent Pin Pokeys Function Pokeys Pin 56U Pokeys Pin 57E 1 5V 5V 5V 2 GND GND GND 3 PoExtension PoExtension PoExtension PoExtension PoExtension PoExtension PoExtension PoExtension PINOUT FOR ENCODER Connector RJ45 for ENCODER RJ45 (ENCODERS) PIN RJ45 Pokeys Function Pokeys Pin 1 GND GND 2 UF.enc.A 8 3 UF.enc.B 12 4 UF.enc.I 13 5 NOT USED NOT USED 6 NOT USED NOT USED 7 5V 5V 8 NOT USED NOT USED User s Manual Page 15
18 15.0 PINOUT LIMIT Connector RJ45 for limit LIMIT PIN RJ45 Pokeys Function Pokeys Pin 1 GND GND 2 Z_LIMIT 30 3 Y_LIMIT 29 4 X_LIMIT 28 5 A_LIMIT 34 6 NOT USED NOT USED 7 5V 5V 8 NOT USED NOT USED This input is compatible with sensors (A32 or A62) WIRING SAMPLE User s Manual Page 16
19 16.0 PINOUT FOR BOARD This connector is compatible with the board (C3 or C48) PIN RJ45 Pokeys Function Pokeys Pin 1 GND 2 NOT USED 3 ERR 4 NOT USED 5 IN LIMIT ERR 7 5V 8 NOT USED WIRING SAMPLE User s Manual Page 17
20 17.0 DIMENSIONS All dimensions are in Millimeters. DISCLAIMER Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC nor Arturo Duncan are liable for any accidents resulting from the improper use of these devices. This board is not a fail-safe device and it should not be used in life support systems or in other devices where its failure or possible erratic operation could cause property damage, bodily injury or loss of life. User s Manual Page 18
USER S MANUAL VER.2. C76- MULTIFUNCTION CNC BOARD Rev. 1.4
USER S MANUAL VER.2 C76- MULTIFUNCTION CNC BOARD Rev. 1.4 MARCH 2018 User s Manual Page i USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 FEATURES... 1 2.0 I/O SPECIFICATIONS... 2 3.0 BOARD DESCRIPTION...
USER S MANUAL VER.1. C34GV BOARD Rev. 1
USER S MANUAL VER.1 C34GV BOARD Rev. 1 JANUARY, 2017 USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 OVERVIEW... 1 2.0 FEATURES... 1 3.0 BOARD DESCRIPTION... 2 4.0 SPECIFICATIONS... 2 4.1 Power Requirements...
USER S MANUAL. E6 POKEYS MOTION CONTROLLER CNC INTERFACE DB25 Rev.1
USER S MANUAL E6 POKEYS MOTION CONTROLLER CNC INTERFACE DB25 Rev.1 April, 2013 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 FEATURES... 2 2.0 SPECIFICATIONS... 3 3.0 SYSTEM REQUIREMENTS... 3 4.0
USER S MANUAL. C35S- QUICK SETUP BREAKOUT BOARD Rev. 1.3
USER S MANUAL C35S- QUICK SETUP BREAKOUT BOARD Rev. 1.3 FEBRUARY, 2015 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 OVERVIEW... 1 2.0 FEATURES... 1 3.0 SPECIFICATIONS.... 2 4.0 BOARD DESCRIPTION...
USER S MANUAL VER.1. C11G- MULTIFUNTCION CNC BOARD Rev. 9
USER S MANUAL VER.1 C11G- MULTIFUNTCION CNC BOARD Rev. 9 MARCH, 2017 User s Manual Page i USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 OVERVIEW... 1 2.0 FEATURES... 1 3.0 SPECIFICATIONS... 2 4.0
USER S MANUAL. C32- DUAL PORT MULTIFUNCTION CNC BOARD Rev. 4
USER S MANUAL C32- DUAL PORT MULTIFUNCTION CNC BOARD Rev. 4 August, 2012 USER'S MANUAL TABLE OF CONTENTS Page # 1.0 FEATURES... 1-1 2.0 SPECIFICATIONS... 2-3 3.0 BOARD DESCRIPTION... 3-4 4.0 FUNCTIONAL
USER S MANUAL. C68 KFLOP MOTHERBOARD Rev. 3 JANUARY 2015.
USER S MANUAL C68 KFLOP MOTHERBOARD Rev. 3 JANUARY 2015. USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 OVERVIEW... 1 2.0 FEATURES... 1 3.0 BOARD DESCRIPTION... 2 4.0 SELECT JUMPER DEPENDING OF THE
USER S MANUAL. C4 SAFETY CHARGE PUMP BOARD Rev. 6.2
USER S MANUAL C4 SAFETY CHARGE PUMP BOARD Rev. 6.2 March 2013 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 OVERVIEW... 1 2.0 FEATURES... 1 3.0 SPECIFICATIONS... 2 4.0 SIMPLIFIED SCHEMAT... 2 5.0
USER S MANUAL. C11S- MULTIFUNTCION CNC BOARD Rev. 1.2
USER S MANUAL C11S- MULTIFUNTCION CNC BOARD Rev. 1.2 SEPTEMBER 2014 User s Manual Page i TABLE OF CONTENTS Page # 1. Overview... 1 2. Features... 1 3. Specifications... 3 4. BOARD DESCRIPTION... 4 5. Special
C45 - LIMIT AND HOME UNIVERSAL BOARD Rev. 1
C45 - LIMIT AND HOME UNIVERSAL BOARD Rev. 1 User manual Rev. 1 1. Overview This card provides an easy means of connecting optical, mechanical and proximity sensor to operate as homing and limit switches
USER S MANUAL. CNC Servo Stepper Motor Control Box CH4EV12-1 Rev. 1
USER S MANUAL CNC Servo Stepper Motor Control Box CH4EV12-1 Rev. 1 January, 2013 i USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 FEATURES... 1 2.0 SPECIFICATIONS... 2 3.0 SYSTEM REQUIREMENTS... 2
USER S MANUAL. C11- MULTIFUNTCION CNC BOARD Rev. 9.9
USER S MANUAL C11- MULTIFUNTCION CNC BOARD Rev. 9.9 FEBRUARY, 2015 User s Manual Page i TABLE OF CONTENTS Page # 1. Overview... 1 2. Features... 1 3. Specifications... 3 4. BOARD DESCRIPTION... 4 5. Special
USER S MANUAL. CNC Stepper Motor Control Box CS3EA4-1 Rev. 1
USER S MANUAL CNC Stepper Motor Control Box CS3EA4-1 Rev. 1 April, 2012 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 FEATURES... 2 2.0 SPECIFICATIONS... 3 3.0 SYSTEM REQUIREMENTS... 3 4.0 WARNING...
C10S- PARALLEL PORT INTERFACE CARD Rev. 1.4
USER S MANUAL VER.1 C10S- PARALLEL PORT INTERFACE CARD Rev. 1.4 SEPTEMBER, 2016 User s Manual Ver.1 Page i USER'S MANUAL TABLE OF CONTENTS Page # 1. OVERVIEW... 1 2. FEATURES... 1 3. SPECIFICATIONS...
C35- QUICK SETUP BREAKOUT BOARD Rev. 1.1
C35- QUICK SETUP BREAKOUT BOARD Rev. 1.1 User manual Rev. 1 1. Overview This card provides an easy way of interfacing your inputs and outputs from the parallel port. It provides terminals and RJ45 for
C4 SAFETY CHARGE PUMP BOARD Rev. 6.2
C4 SAFETY CHARGE PUMP BOARD Rev. 6.2 User manual Rev. 1 1. Overview. This board takes advantage of Mach ability to send a specific frequency through one of the pins of the parallel port when the program
USER S MANUAL VER.1. C10- PARALLEL PORT INTERFACE CARD BOARD Rev. 11
USER S MANUAL VER.1 C10- PARALLEL PORT INTERFACE CARD BOARD Rev. 11 FEBRUARY, 2017 User s Manual Page i USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 OVERVIEW... iii 2.0 FEATURES... iii 3.0 SPECIFICATIONS...
USER S MANUAL VER.1. C10D- PARALLEL PORT INTERFACE CARD BOARD Rev. 1
USER S MANUAL VER.1 C10D- PARALLEL PORT INTERFACE CARD BOARD Rev. 1 MARCH 2018 User s Manual Page i USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 OVERVIEW... iii 2.0 FEATURES... iii 3.0 SPECIFICATIONS...
USER S MANUAL C10- PARALLEL PORT INTERFACE CARD
USER S MANUAL C10- PARALLEL PORT INTERFACE CARD Rev. 10 June, 2012 USER'S MANUAL TABLE OF CONTENTS Page # 1. OVERVIEW... 1 2. FEATURES... 1 3. SPECIFICATIONS... 2 4. BOARD DESCRIPTION... 3 Using configuration
C3 INDEX PULSE BOARD Rev. 6
C3 INDEX PULSE BOARD Rev. 6 User manual Rev. 1 Fig. 1. C3 Index Pulse Board 1. Overview. This card provides easy way of capturing the pulse signal from photo-transistor and transmitting it to the parallel
C10- PARALLEL PORT INTERFACE CARD Rev. 8
C10- PARALLEL PORT INTERFACE CARD Rev. 8 User manual Rev. 1 1. Overview This card provides an easy way of interfacing your inputs and outputs from you parallel port. It provides terminals for the connections
C50- PARALLEL PORT INTERFACE CARD Rev. 1
C50- PARALLEL PORT INTERFACE CARD Rev. 1 User manual 1. Overview This card provides an easy way of interfacing your inputs and outputs from you parallel port. It provides terminals for the connections
USER S MANUAL. C33 - MULTIFUNCTION ROUTER BOARD BOARD Rev. 4
USER S MANUAL C33 - MULTIFUNCTION ROUTER BOARD BOARD Rev. 4 June 2013 USER'S MANUAL TABLE OF CONTENTS Page # Contents 1.0 OVERVIEW... 3 2.0 FEATURES... 3 3.0 SPECIFICATIONS... 4 4.0 FUNCTIONAL BLOCK DIAGRAMS...
C11G- MULTIFUNTCION CNC BOARD Rev. 8.2
C11G- MULTIFUNTCION CNC BOARD Rev. 8.2 User manual Rev. 2 1. Overview This card has been designed to provide a flexible interface and functions to your computer projects, by using the parallel port control
C33- MULTIFUNCTION ROUTER BOARD Rev. 2
C33- MULTIFUNCTION ROUTER BOARD Rev. 2 User manual Rev. 1 1. Overview This card provides an easy way of interfacing your router based spindle with your steeper motor driver board. This board includes a
C23- DUAL PORT MULTIFUNCTION CNC BOARD Rev. 3.1
C23- DUAL PORT MULTIFUNCTION CNC BOARD Rev. 3.1 User manual Rev. 2 1. Overview This card has been designed to provide a flexible interface and functions to computer CNC projects, by using the parallel
CNC4PC. C11G - MULTIFUNCTION CNC BOARD Rev. 5.4
CNC4PC Manual C11G - MULTIFUNCTION CNC BOARD Rev. 5.4 Overview This card has been designed to provide a flexible interface and functions to your computer projects, by using the parallel port control software.
USER S MANUAL VER.3. C25- SMOOTH STEPPER LPT BOARD Rev. 5
USER S MANUAL VER.3 C25- SMOOTH STEPPER LPT BOARD Rev. 5 MAY, 2017 User s Manual Page i USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 FEATURES... 1 2.0 SPECIFICATIONS... 1 3.0 FUNCTIONAL BLOCK DIAGRAMS...
HDBB Breakout board user s manual
HDBB Breakout board user s manual The HDBB breakout board was designed to use with our Whale2(-T)*, Whale3, Mammut* and Dugong servo drives or with any other third party stepper or servo drives which using
CNC4PC. MULTIFUNCTION CNC BOARD Rev2
CNC4PC Manual MULTIFUNCTION CNC BOARD Rev2 Overview This card has been designed to provide a flexible interface and functions to your computer projects, by using the parallel port control software. This
Breakoutboard for ESS Smoothstepper
Breakoutboard for ESS Smoothstepper Operation Manual All rights to these operating instructions remain with cnc-technics. Texts, information and illustrations of these operating instructions may not be
PP-BOB2-V2.0 PARALLEL PORT BREAKOUT BOARD
PP-BOB2-V2 PARALLEL PORT BREAKOUT BOARD Document: Operation Manual Document #: T18 Document Rev: 1.0 Product: PP-BOB2-V2.0 Product Rev: 1.0 Created: October, 2015 THIS MANUAL CONTAINS INFORMATION FOR INSTALLING
PP-BOB2-V1.0 PARALLEL PORT BREAKOUT BOARD
PP-BOB2-v1 PARALLEL PORT BREAKOUT BOARD Document: Operation Manual Document #: T17 Document Rev: 2.0 Product: PP-BOB2-v1.0 Product Rev: 1.0 Created: March, 2013 Updated: Dec, 2014 THIS MANUAL CONTAINS
IO3-R2 BREAKOUT BOARD
IO3-R2 BREAKOUT BOARD DESCRIPTION Breakout board IO3-R2 (Revision R2) has digital buffer for STEP/DIR/ENA command signals and as such it is particularly suitable for the connection up to 4 microstep drives
Breakoutboard für UC400ETH
Breakoutboard für UC400ETH Operation Manual All rights to these operating instructions remain with cnc-technics. Texts, information and illustrations of these operating instructions may not be reproduced,
Apollo I Breakout Board User s Manual
MACHMOTION Apollo I Breakout Board User s Manual 1/14/2012 Everything you need to know to set up and use your Apollo I Breakout Board. MachMotion Version 1.0.1 2 P a g e M a c h M o t i o n Copyright 2012,
uservo box instruction manual
Safety notes uservo box instruction manual Every machine controlled by computer (PC) can be really dangerous for human life and health. Comply with bolow rules and use Your common sense while working with
PoExtBus User s manual
PoExtBus User s manual PoExtBus user s manual 1. Description... 3 Master devices which support PoExtBus:... 3 Slave devices which support PoExtBus:... 3 Features... 3 Requirements... 3 2. PoExtBus technical
User Manual of 5Axis Breakout Board
WWW.VALLDER.COM User Manual of 5Axis Breakout Board Safety Statement Vallder Ltd is not liable or responsible for any accidents, injuries, equipment damage, property damage, loss of money or loss of time
Hardware Manual CNC760
Hardware Manual CNC760 Revision 3 6 December, 2017 Released Copyright 2017 by Eding CNC History: Revision Date Author 1 22-5-2017 AB 2 23-6-2017 AB 3 6-12-2017 AB Revision overview: Revision Remarks 1
Hardware Installation Manual MX Axis Stepper Drive with Breakout Board & I/O s
Hardware Installation Manual MX3660 3-Axis Stepper Drive with Breakout Board & I/O s Version 1.0 11 / 2013 Hardware Manual for MX3660 3-Axis Stepper Drive with Breakout Board & I/O s ii Notice Read this
CNC4PC. M1 Modbus Serial Server Manual Rev. 2
CNC4PC Manual M1 Modbus Serial Server Manual Rev. 2 Overview This board allows easy to setup Modbus communications. Its flexible configuration allows for implementing multiple output or expansion boards
PoKeys57CNC User s manual. Version: 26/9/2016
PoKeys57CNC User s manual Version: 26/9/2016 Please read the following notes 1. All information included in this document is current as of the date this document is issued. Such information, however, is
G540 4-AXIS DRIVE REV 4: MAY 28, 2010
Thank you for choosing to purchase the G540 4-Axis Drive System. If you are dissatisfied with it for any reason at all within two weeks of its purchase date, you may return it for a full refund provided
Manual. Model#-DB25M-3R6A. 6 Axis CNC Interface Breakout Board. Lastest update : Feb Store this manual away for further reference.
Manual 6 Axis CNC Interface Breakout Board Model#-DB25M-3R6A Lastest update : Feb 2016 Read this manual carefully before making connections to the board. Store this manual away for further reference. Safety
MaxStepper Serial Step and Direction Pulse Generator. User Manual
MaxStepper Serial Step and Direction Pulse Generator User Manual 2007 Kellyware 9/20/2007 WWW.KELLYWARE.COM Table of Contents Table of Contents... 2 Parts List... 3 Key Features... 3 Introduction... 4
DigiSpeed-SD DC-06. Isolated Control Voltage Generator User s Guide. DigiSpeed-SD PCB Ver:3.0 Mach3 Ver: 2.+ DigiSpeed-SD - Users Guide Page 1
DigiSpeed-SD - Users Guide Page 1 Updated: 4 th May 2011 DigiSpeed-SD DC-06 Isolated Control Voltage Generator User s Guide DigiSpeed-SD PCB Ver:3.0 Mach3 Ver: 2.+ DigiSpeed-SD - Users Guide Page 2 Homann
AXBB-E ethernet motion controller and breakout board user's guide
AXBB-E ethernet motion controller and breakout board user's guide Version of this document: 1.0002 1/29 Contents 1.Description of the AXBB-E device. 2.Safety notes. 3.Physical installation of the device.
PoKeys57CNC and Mach4
PoKeys57CNC and Mach4 Step by step guide - a.k.a. beginners guide Version: 13/12/2017 SAFETY INFORMATION This product is intended for integration by the user into a computer numerical control (CNC) machine.
VSDEPI VSD-E/XE Parallel Interface breakout board Manual Ver. 1.1
Introduction VSD-E/XE Parallel interface is a breakout board designed to ease connection of up to four VSD-E/XE drives in single D-Sub 25 connector. Connector pin-out has been designed for step/dir operation
UNIVERSAL MOTION INTERFACE (UMI) ACCESSORY
USER GUIDE UNIVERSAL MOTION INTERFACE (UMI) ACCESSORY Introduction This user guide describes how to use the UMI-A, UMI-Flex, and UMI-Flex accessories. The UMI products are connectivity accessories you
G540 User Manual. Date Modified: March 5, 2012 Page 1 of 10
G540 User Manual Date Modified: March 5, 2012 Page 1 of 10 DIMENSIONS PHYSICAL AND ELECTRICAL RATINGS Minimum Maximum Units Supply Voltage 18 50 VDC Motor Current 0 3.5 A Power Dissipation 1 13 W Short
ACORN User Guide For Revision (Aka Acorn_rev3) Updated 1/23/17
ACORN User Guide For Revision 171025 (Aka Acorn_rev3) Updated 1/23/17 Overview ACORN is technically a breakout board for the BeagleBone Green or BeagleBone Black embedded computer. The remainder of this
VSDEPI VSD-E Parallel Interface breakout board Manual Ver. 0.9
Introduction VSD-E Parallel interface is a breakout board designed to ease connection of up to four VSD-E drives in single D-Sub 25 connector. Connector pin-out has been designed for step/dir operation
PMDX-105. I/O Option Riser Board User s Manual. Document Revision: 1.1 Date: 7 September 2004 PCB Revision: PCB-443A
PMDX-105 I/O Option Riser Board User s Manual Date: 7 September 2004 PMDX Web: http://www.pmdx.com 7432 Alban Station Blvd., A105 Phone: +1 (703) 912-4991 Springfield, VA 22150-2321 USA FAX: +1 (703) 912-5849
PLCM-B1 Breakout board for PLCM-E3/E3p controller
www.purelogic.ru User manual CONTENTS: 1. General information... 2 2. Delivery set... 2 3. Technical specifications... 3 4. Key features... 4 5. Sockets purpose and indication... 6 6. Connection... 11
HiCON Integra pn7766
HiCON Integra pn7766 Ethernet Motion Controller Data Acquisition System Logic Controller User Guide Document Revision 1.0 (Updated March 12, 2013) 2013 Vital Systems Inc Phoenix, AZ USA For more information
G540 MANUAL MULTIAXIS STEP MOTOR DRIVE
G540 MANUAL MULTIAXIS STEP MOTOR DRIVE PRODUCT DIMENSIONS PHYSICAL AND ELECTRICAL RATINGS Minimum Maximum Units Supply Voltage 18 50 VDC Motor Current 0 3.5 A Power Dissipation 1 13 W Short Circuit Trip
TB6600 Stepper Motor Driver
TB6600 Stepper Motor Driver V1.0 07 2018 Open Source Mechatronics LTD 2018 Safety Statement The author of this document is not liable or responsible for any accidents, injuries, equipment damage, property
PoExtBusOC16-CNC User s manual
PoExtBusOC16-CNC User s manual Please read the following notes 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change
SUM-40 OPERATING MANUAL. Ma0 DYNAMIC STRUCTURES AND MATERIALS, LLC REV
Ma0 SUM-40 OPERATING MANUAL DYNAMIC STRUCTURES AND MATERIALS, LLC REV. 171011 Please review the following points for both personal and equipment safety while operating the SUM-40 motor. HIGH ENERGY/VOLTAGE
3-Axis Stepper Drive Datasheet MX3660
3-Axis Stepper Drive Datasheet MX3660 3-Axis Stepper Drive + Breakout Board, 20-60VDC, 6A Peak Version 0.0.2 http://www.leadshine.com Features Three individual stepper drive boards Suitable for NEMA17
Manual 5 Axis CNC Interface Breakout Board Model#-DB25-1R5AM
Manual 5 Axis CNC Interface Breakout Board Read this manual carefully before making connections to the board. Store this manual away for further reference. Safety Notes: The electronics of the control
Preliminary Datasheet MX Axis Stepper Drive with Breakout Board & I/O s. Preliminary V1.0
Preliminary Datasheet MX4660 4-Axis Stepper Drive with Breakout Board & I/O s Preliminary V1.0 Features Power up to 4 stepper motors of NEMA 17, 23, 24, or 34 Sophisticated stepper motor control based
AN004 Using the PMDX-126 s Error Input and Restart Output with Geckodrive Servo Drivers and Mach3 CNC Software
1.0 Overview This application note describes how to connect the to the Geckodrive G320//G340 step servo driver s ERR/RST terminal to allow the to detect a Geckodrive error (fault) state and to reset the
UNIVERSAL MOTION INTERFACE (UMI) ACCESSORY
USER GUIDE UNIVERSAL MOTION INTERFACE (UMI) ACCESSORY Contents This user guide describes how to use the UMI-77, UMI-A, UMI-Flex, and UMI-Flex accessories. Introduction... What You Need to Get Started...
Defining the Future in Motion Control
Defining the Future in Motion Control USER S MANUAL 1 DINIO7 user s manual Overview The DINIO7 is a DIN-rail mounted peripheral for the SmartMotor versions 3 and 4 product lines Hereafter, the SmartMotor
PMDX-108-Output. 8-Channel Isolated Output Board for PC parallel port pins 2-9. User s Manual
PMDX-108-Output 8-Channel Isolated Output Board for PC parallel port pins 2-9 User s Manual Date: 25 February 2010 PMDX Web: http://www.pmdx.com 9704-D Gunston Cove Rd Phone: +1 (703) 372-2975 Lorton,
CSMIO-MPG. 6-axis Manual Pulse Generator (MPG) Module. Rev copyright 2014 CS-Lab s.c.
CSMIO-MPG 6-axis Manual Pulse Generator (MPG) Module Rev. 2.0 copyright 2014 CS-Lab s.c. Index 1. General information...3 1.1 Signs used in this guide... 3 1.2 Standards compliance... 4 1.3 Technical data...
PoKeys Pulse engine v2 documentation
Version: 6/3/2016 SAFETY INFORMATION! This product is intended for integration by the user into a computer numerical control (CNC) machine. It is the user's responsibility to assess the overall system
Novusun Controller Wiring and MACH3 Software Setup
Novusun Controller Wiring and MACH3 Software Setup V1.0 01 2019 Open Source Mechatronics LTD 2019 Safety Statement The author of this document is not liable or responsible for any accidents, injuries,
Current plugin version: V1.028
UC300-5LPT USB CNC motion controller to use with MACH3 software Current plugin version: V1.028 Contents: 1. Product description and background of working. 2. Pinouts a. Connectors placement and types.
Hardware Installation Manual MX Axis Stepper Drive with Breakout Board & I/O s
Hardware Installation Manual MX3660 3-Axis Stepper Drive with Breakout Board & I/O s Version 1.1 12 / 2013 http://www.leadshine.com http://www.leadshineusa.com 2013 Leadshine Technology Co., Ltd. Hardware
BrewTroller Phoenix. Owners Manual. Updated - March 14, 2016 BREWTROLLER PHOENIX 1
BrewTroller Phoenix Owners Manual Updated - March 14, 2016 BREWTROLLER PHOENIX 1 2016 BrewTroller All Rights Reserved. Product warranty or service will not be extended if: (1) the product is repaired,
PMDX-416 SmartBOB-OptoUSB For use with Mach4
PMDX-416 SmartBOB-OptoUSB For use with Mach4 User s Manual Document Revision: 1.0 Date: 1 July 2016 Circuit Board Revisions: PCB-534A PMDX Web: http://www.pmdx.com 9704-D Gunston Cove Rd Phone: +1 (703)
Centroid ACORN CNC controller Specification and Use Guide Updated 8/3/17. Overview
Centroid ACORN CNC controller Specification and Use Guide Updated 8//7 Overview ACORN is technically a CNC control breakout board for the BeagleBone Green or BeagleBone Black embedded computer the Beagle
Apollo III INSTALLATION MANUAL
Apollo III INSTALLATION MANUAL 2 P a g e 5/1/14 N0112 This manual covers the setup and configuration of the Apollo III motion controller connected to the control using Mach3. Formatting Overview: Menus,
PoExtBus User s manual
PoExtBus User s manual PoExtBus user s manual 1. Description... 3 Master devices which support PoExtBus:... 3 Slave devices which support PoExtBus:... 3 Features... 3 Requirements... 3 2. PoExtBus technical
RTK4 Logic Controller User Manual For RTK4L Revision Revised
RTK4 Logic Controller User Manual For RTK4L Revision 120326 Revised 6-20-12 RTK4 Features Application: PLC and Third Party Drive Interface Number of Axis Drive Interfaces: 5 Axis DAC Resolution: 16 bits
4 CHANNEL 5V RELAY MODULE
4 CHANNEL 5V RELAY MODULE A relay is an electrically operated device. It has a control system and (also called input circuit or input contactor) and controlled system (also called output circuit or output
UNIPORT V3. C R H Electronics Design
UNIPORT V3 V C R H Electronics Design Uniport V3 USB powered Parallel port interconnection board with optical isolated inputs, buffered outputs, charge pump interlock and power relays By C R Harding Specification
MCA-7724 MOTION AXIS ROUTER
USER GUIDE MCA-7724 MOTION AXIS ROUTER Introduction Features The MCA-7724 Motion Axis Router reroutes the signals from your motion controller into separate connectors that connect to different motion accessories.
Breakoutboard Rev.2 for Estlcam
Breakoutboard Rev.2 for Estlcam 1 Stefan Gemeinert,Frühlingstrasse 8 85253 Erdweg Operation Manual All rights to these operating instructions remain with cnc-technics. Texts, information and illustrations
EN006 - DigiSpeed Selection Chart
- Selection Chart The range is designed to allow you to control the speed of your spindle motor from your CNC software. They do this by accepting a control signal from the CNC software and converting to
Using the PMDX-125/126 Mach3 Plug-In Ver
Unless otherwise stated, this manual uses the term PMDX-125 generically to refer to both the PMDX-125 and PMDX-126 boards. The PMDX-125 Plug-In will work with either a PMDX-125 or PMDX-126 board. 1.0 Terms
Hardware Installation Manual MX Axis Stepper Drive with Breakout Board & I/O s
Hardware Installation Manual MX3660 3-Axis Stepper Drive with Breakout Board & I/O s Version 1.2 3 / 2015 http://www.leadshine.com http://www.leadshineusa.com 2015 Leadshine Technology Co., Ltd. Hardware
HiCON Integra pn7766
HiCON Integra pn7766 Ethernet Motion Controller Data Acquisition System Logic Controller User Guide Document Revision 1.5 (Updated Jan 19, 2017) 2017 Vital Systems Inc Phoenix, AZ USA For more information
UCBB dual port breakout board user's manual
UCBB dual port breakout board user's manual 1/14 Contents 1 Features 2 Dimensions 3 Connectors 3.1 Screw terminals 3.2 IDC ports 3.3 Powering 3.4 Outputs 3.5 Inputs 4 LED indicators 5 Example connections
UNIPORT V2. Uniport V2
UNIPORT V2 Uniport V2 USB powered Parallel port interconnection board with optical isolated inputs, buffered outputs, charge pump interlock and power relays Specification Full optical isolation of all
FTC200 & FTA/FTX Quick Installation & Jumper Setting Guide
FTC200 & FTA/FTX Quick Installation & Jumper Setting Guide Accuthermo Technology Corp. Safety Note Please read this entire document before you begin connecting cables and assembling your system Failure
UIM2901-5A. Page 2. UI Robot Technology Co. LTD M EN. Please pay attention to the following before using the UIROBOT products:
User Manual MACH3 Breakout Board Please pay attention to the following before using the UIROBOT products: UIROBOT products meet the specification contained in their particular Data Sheet. UIROBOT will
Release Note. How to Use the OptoCon Connection Module. 1 Introduction. Option C Revision 4 Revised 8/13/98
33 South La Patera Lane Santa Barbara, CA 93117-3214 ph (805) 681-3300 fax (805) 681-3311 tech@motioneng.com www.motioneng.com Release Note How to Use the OptoCon Connection Module Option C002-0007 Revision
Datasheet MX Axis Stepper Drive with Breakout Board & I/O s. Version1.0
Datasheet MX3660 3-Axis Stepper Drive with Breakout Board & I/O s Version1.0 1. Features Power up to 3 stepper motors of NEMA 17, 23, 24, or 34 Sophisticated stepper motor control based on latest DSP technology
I.CH Brushless DC Motor Driver
V II 20100513 I.CH Brushless DC Motor Driver I.CH MOTION CO., LTD MOTION WORLD Characteristic : This control system with perfect function, simple operation, capability of anti-interference, energy saving,
Appendix E: Edge Ti. Overview. Appendix E: Edge Ti 169
Appendix E: Edge Ti 169 Appendix E: Edge Ti Overview The Edge Ti shape cutting control is an extremely versatile product offering up to four configurable axes of motion, built-in Servo Amplifiers and configurable
Apollo III User Manual - Mach3
Apollo III User Manual - Mach3 WARNING! Improper installation of this motion controller can cause DEATH, INJURY or serious PROPERTY DAMAGE. Do not attempt to install this controller until thoroughly reading
CPU5A Economy Series USBCNC software included. Features
CPU5A Economy Series 125 KHz step frequency, 4 axes. Card size 100x100mm. USB 2.0 connection. 100 Mbit Ethernet connection (*). 5 Status LED's. Full 4 axes interpolation (*). 7 Standard CNC outputs. 0-10V
1. Key Features. 2. Photo of 4-AXIS CNC Board
This document describes the basic functionality and the electrical specifications of StepperOnline s Four Axis TB6600 CNC Driver Board. 1. Key Features Supports MACH3, KCAM4, EMC2 etc Can drive four channels
User Manual. For 3rd Generation. 5 Axis Standard & Professional Breakout Board Set
The 3 rd Generation 5 Axis Breakout Board Set User Manual For 3rd Generation 5 Axis Standard & Professional Breakout Board Set Attention: Please read the manual carefully before using the products! Email:
TurboTaig Instruction Manual
TurboTaig Instruction Manual Version: 2.2 Peter Homann 20 View St Highett 3190 homann@smartchat.net.au http://people.smartchat.net.au/~homann 1 Table of Contents Table of Contents... 2 Introduction...