Drexel University Electrical and Computer Engineering Department ECE 200 Intelligent Systems Spring Lab 1. Pencilbox Logic Designer

Size: px
Start display at page:

Download "Drexel University Electrical and Computer Engineering Department ECE 200 Intelligent Systems Spring Lab 1. Pencilbox Logic Designer"

Transcription

1 Lab 1. Pencilbox Logic Designer Introduction: In this lab, you will get acquainted with the Pencilbox Logic Designer. You will also use some of the basic hardware with which digital computers are constructed (i.e. NAND gates, NOR gates, etc.). You will apply the techniques you have already learned for designing logic circuits. Objective: a) Become familiar with the Pencilbox Logic Designer, the integrated circuit (IC) chips and building a digital circuit on a breadboard. b) Learn how to test IC chips and obtain the truth table of the Logic Gates. c) Measure digital voltages using a voltmeter. The Pencilbox: The LD-1 Pencilbox Logic Designer kit is an instrument used to implement and test digital circuits. It can be used in the study and design of logic gates, counters, multiplexers, and flip-flops, and also for simple microprocessor circuits. Circuits such as clocks, switches and lights are permanent parts of the LD-1 and need not be repeatedly constructed. Students build only those circuits which directly pertain to a particular experiment. Everything required to design and experiment with logic circuitry is included in the Pencilbox. Power is supplied by an AC adapter. The LD-1 is housed in a tough molded plastic carrying case with an integral hinged cover which makes it possible to partially implement a circuit and then conveniently store or transport the entire kit for later use or evaluation. External Breadboard Power Supply PencilBox Logic Switches Logic Indicators Power Pulsers Clock Internal breadboard Control Strip 8/1/2007 1

2 Drexel University The unit has 8 output ports called Logic Indicators in the form of 8 LEDs. They are labeled from D0 through D7. These are used to display output signals from digital circuits and also serve as logic probes for circuit testing. There are 8 input ports called Logic Switches. These are toggle switches and they are labeled S0 through S7. Note that when a switch is OPEN, it is Logic 1. These are used to provide input signals to a digital circuit. The unit also contains 2 push-button Pulsers and a clock. The Pulsers are used to provide logic pulses to a digital circuit. The pulse lasts as long as the button is depressed. The clock provides a square wave at approximately 1 khz, but this frequency can be varied by adding an external capacitor. Power is supplied to the entire internal circuitry of the kit by moving the switch S1 to the ON position. Note: This does not apply power to the Breadboard area. All of these functions are internally connected to a solderless interconnect socket, called the Control Strip, with five tie points for each signal. Two general-purpose sockets (or breadboards ) are provided as a convenient work area for circuitry being designed or studied. One of the breadboards is external to the Pencilbox and another is internal to it. 8/1/2007 2

3 Drexel University The Integrated Circuit: In this Lab we will be using 3 different Integrated Circuit (IC) chips. They are the 7400 IC chip which has four 2-input NAND gates, the 7402 IC chip which has four 2input NOR gates and the 7404 IC chip which houses six NOT (inverter) gates. Each of these IC chips has 14 pins (7 on each side) which are labeled from 1 to 14. In every IC chip, pin 7 must be connected to Logic 0 (Ground = 0V) and pin 14 to Logic 1 (Vcc = 5V). The Notch Pin No Pin No. 7 (Ground) (Vcc) Pin No Pin No. 8 Pin Numbering depends on the location of the Notch. The pin to the left of the notch is labeled Pin 1. The pin to the right of the notch is labeled Pin 14. The remaining pins are labeled as shown in the adjacent figure. In order to identify the IC chip, you need to look at the numbers on top of the IC chip. Here are some examples along with the Pin configuration of the gates housed in each IC chip IC (4 NANDs) 7402 IC (4 NORs) 7404 IC (6 NOTs) 8/1/2007 3

4 Breadboarding Instructions: 1) Keep a wire cutter/stripper and a small screwdriver handy. 2) Generate a neat and complete circuit diagram on paper to help you guide with the wiring. Every time you add a wire or component to the physical circuit, mark off the corresponding part of the wiring on your circuit diagram. 3) Before handling IC chips, discharge any electrostatic charge on your body by touching metal. Insert IC packages into the appropriate breadboard area before inserting any wires. You may need to bend the IC leads (pins) slightly inward so that the spacing closely matches the spacing of sockets on the breadboard. Be careful to check that all IC leads actually make it into the correct sockets. 4) To remove an IC, use an extraction tool, screwdriver, pliers or tweezers to avoid bending or breaking IC leads, or personal injury. 5) Use the connector wires available in the lab for wiring. Wire strippers may be used to cut wires to appropriate lengths. 6) Make sure the wires are not too thick (which could stretch the connector sockets) or too thin (which could result in unreliable or intermittent connections). 7) When removing wires, be sure to pull at a right angle to the socket to avoid damage. 8) Route wires around IC packages, not over them. Occasionally an IC turns out to be defective. If wires have been placed over the IC, you will have to remove them so that the IC can be replaced. 9) Wire a circuit in stages, beginning with power and ground connections. Add wires with the power switch OFF. Before turning power ON, make sure that no foreign metal objects are near the circuit. 10) Check every IC to make sure it is not overheating. If any IC is too hot to touch immediately shut the power off and check all leads. (Shorted ICs can become very hot!) Also make sure that no IC has been inserted backwards. IC devices can be damaged if the power level exceeds 5.5V. Damage may also occur if the supply voltage connection is removed from the IC pin while power is still being applied to the circuit. 11) To debug a circuit, use the logic indicator (L0 - L7) to check logic levels. Start at a position in the circuit where the logic level is known to be correct and work outward from there. If an IC does not appear to produce the correct signal, check that power and ground are correctly connected to the IC; also check all inputs to the component. Finally, check that the output of the IC is not incorrectly connected to some other signal. Upper 2 rows The breadboard is divided into 2 halves, by a central channel. Perpendicular to upper half this channel are many columns of five holes each. The five holes central channel of each column are electrically connected together. They are not lower half connected to any other part of the lab kit. A single column will be used to provide access to one pin of an IC. Lower two rows In addition, a breadboard has two upper rows and two lower rows (usually used for Logic 0 and Logic 1 connections). Note that each of these four rows has 50 holes; in 8/1/2007 4

5 each row, the first 25 holes are electrically connected to each other, the next 25 holes are electrically connected to each other. The Control Panel: 1) The Control Strip (also called Control Panel) is located near the center of your kit. Similar to a breadboard, it has five rows; the five holes in each column are electrically connected together. The Control Strip contains connectors with labels such as LOGIC INDICATORS, LOGIC SWITCHES etc. It provides power and control signals to the circuit which will be built on the Breadboard area. A circuit is built on the breadboard by placing electrical components on the breadboard and attaching wires between the Control Strip and the Breadboard. 2) Before applying power to the kit, remove all metal objects from the vicinity of the kit. Move switch S1 to OFF position. Plug the AC adapter into a standard (120 VAC) wall outlet. Now move switch S1 to the ON position. This applies power to the internal circuitry of the kit only. No power is applied to the Breadboard area. Whenever you are finished working with the kit, move S1 to the OFF position before disconnecting the power. 3) Locate the connectors labeled LOGIC 1, +5 and LOGIC 0, GND on the Control Strip (I). These are the power source for all of your devices. Be very careful when connecting wires to these areas. Although the voltage level is too low to be dangerous to you, sparks can result and you can easily damage the kit. 4) Locate the LOGIC INDICATOR connectors labeled L0 through L7 on the Control Strip. When a 5-volt signal is present at one of these connections, the corresponding LED is illuminated. Check out all of the LEDs in your kit by inserting a wire from one of LOGIC 1 power connectors to each of the LOGIC INDICATOR connectors in turn. Each LED should glow. Check these LEDs each time you work with your kit. 5) Locate the LOGIC SWITCHES connectors on the Control Strip: S0 through S7. These provide connections to 8 switches near the top of the kit. Connect switch S0 to an LED through the connection L0, and turn the switch ON and OFF a few times. Note which setting corresponds to a logic level 1 (the LED is on) and which corresponds to a logic level 0 (the LED is off). Make sure that all of the switches are functioning by testing each one in turn. 6) Power switch S1 should ALWAYS be OFF when inserting or removing ICs to prevent damage to the chips. Turn the power off and place one of the 7400 ICs near the center of the Breadboard area. VERY IMPORTANT: The two rows of pins of the IC should be on different sides of the central channel of the Breadboard. Push the IC so that each pin of the IC is inserted into a separate hole. There should now be four unused holes for each pin along the sides of the IC. Connections can be made to the IC through any of these exposed holes. Check the pin definitions (given in the previous section) and connect LOGIC 1 of the Control Panel to the VCC pin and LOGIC 0 to the GND pin. Again using the Control Panel, connect two Logic Switches to the input pins of one NAND gate. Connect the output of this NAND gate to one Logic Indicator. Verify that the NAND gate works properly by turning power ON and trying all 8/1/2007 5

6 four possible switch settings and observing the LED. This is how you test each gate in an IC chip. 7) Now turn power OFF DC Voltage Measurements: You will be using the Hewlett Packard (HP) Multi-meter 34401A available in Rooms and to perform voltage measurements. This multi-meter can measure DC/AC voltages and currents, resistances, Period and Frequency. The parameter to be measured can be selected via the buttons on the Function Panel. You will need a pair (black and red) of 'Banana to Alligator' cables, which are available in Room Turn on the Multi-meter by pressing the 'Power' button. Since you need to measure DC voltages, press the 'DC V' button on the Function Panel. There are two pairs of HI (red)-lo (black) terminals on the multi-meter. One HI-LO pair is on the left and the other HI-LO pair is on the right. In order to measure voltage, you will need the HI-LO terminal pair on the right (labeled V ). Insert the banana end of the Red cable into this HI terminal. Insert the banana end of the Black cable into the corresponding LO terminal (just below the HI terminal). You are now ready to measure voltage. Let G be the ground pin on your IC chip and let O be the pin on the chip where you want to measure the voltage. Connect the alligator end on the Black cable to the Ground pin G of your IC chip via a connector wire. Connect the alligator end on the Red cable to the pin O on the chip via a connector wire. Record the voltage reading displayed on the multi-meter with the appropriate units. Remember that this voltage measurement indicates the voltage at pin O with respect to Ground. 8/1/2007 6

7 Pre-Lab Exercise Read the instructions in the previous sections of this manual. Pay careful attention to the lay-out of the pins on the IC chips, the connectors on the Control Panel, use of the light emitting diodes (LED s), etc. Complete this form, get it signed by the Lab Assistant in Room and turn it in with the Lab Report. 1) How many Logic Indicators does the unit have? Label them. 2) How many Logic Switches does the unit have? Label them. 3) When a switch is open, is it Logic 0 or Logic 1. 4) Power Switch S1 supplies power to 5) How many tie-points does each signal on the Control strip have? 6) What kind of gates does a 7400 IC chip have? How many? 7) What kind of gates does a 7402 IC chip have? How many? 8) What kind of gates does a 7404 IC chip have? How many? 9) How many pins do each of the above IC chips have? 10) How many Volts is Logic 0 and Logic 1? 11) In each of the above IC chip, which pin is Logic 0? Which pin is Logic 1? 12) Complete the following Truth Table A B A NAND B A NOR B NOT A ) Number all the output pins on the 7400 IC chip. 14) Number all the output pins on the 7402 IC chip. 15) Number all the output pins on the 7404 IC chip. 16) How many electrically connected holes does each column on the breadboard have? 17) A breadboard has 2 upper rows and 2 lower rows. Each row has 50 holes. How many of these holes are electrically connected to each other? 18) Have you carefully read and understood the entire handout? 19) Use the Breadboard simulation software (as seen in class) to wire an NAND (7400) IC. The simulation software can be found on the CD with the book, or at the demo version at For 1 NAND gate, step through all the possible states, and prove that the NAND chip works as expected. Provide a screen shot(s) that proves that the circuit is wired correctly and the chip is working Group member names: Lab assistant signature Date 8/1/2007 7

8 Lab Experimentation: Drexel University 1) Test all the gates in the following IC chips and validate your results using the truth tables from your Pre-lab. Use the switches for the inputs into the ICs. To validate the truth tables, put the output of the chips to the LEDs. Use a data sheet that has enough space to record truth tables for gates on all chips. a) 7404 chip with six NOT gates (Inverters) b) 7402 chip with four 2-input NOR gates c) 7400 chip with four 2-input NAND gates 2) Use a voltmeter to measure the voltages corresponding to Logic 0 and Logic 1 at the output pin of each gate for the NOT, NOR, and NAND ICs. Comment on the voltage levels for a HIGH and LOW signal. a) Measure the voltage when the output pin of the gate is not connected to an LED (Logic Indicator) b) Measure the voltage when the output pin of the gate is connected to an LED (Logic indicator). From (a) and (b) notice and comment on the Loading effect introduced by the LED in the circuit. 3) Use the voltmeter to measure the voltages at both the pins (touch a lead to each pin of the LED) of any one LED, which is ON (or lit up). Remember that these voltages are measured with respect to ground. Let these voltages be V 1 and V 2. The difference V 1 V 2 will be the voltage across the LED. Note down V 1, V 2 and V LED = V 1 V 2. 8/1/2007 8

Discharge by touching: BNC coax shield, outlet metal cover plate, wire connected to GND

Discharge by touching: BNC coax shield, outlet metal cover plate, wire connected to GND Step-down transformer Very High Voltage Very Low Current Lower Voltage, 110V Power Station Grounding contact (3rd wire) Faulty wiring makes box hot!! Current path splits: 1) to ground (mostly) 2) through

More information

CS4141 IDL Notes. I. Quick Overview of IDL Prototyping Unit

CS4141 IDL Notes. I. Quick Overview of IDL Prototyping Unit CS4141 IDL Notes IDL-800 Prototyping System The IDL-800 logic panels are powerful tools for any logic designer. They enable a wide range of IC s to be used in a breadboard experiment. I. Quick Overview

More information

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science Introductory Digital Systems Laboratory

Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science Introductory Digital Systems Laboratory Massachusetts Institute of Technology Department of Electrical Engineering and Computer Science 6.111 -- Introductory Digital Systems Laboratory NUBUS LABORATORY KIT For your pleasure and convenience,

More information

Digital Circuits. Page 1 of 5. I. Before coming to lab. II. Learning Objectives. III. Materials

Digital Circuits. Page 1 of 5. I. Before coming to lab. II. Learning Objectives. III. Materials I. Before coming to lab Read this handout and the supplemental. Also read the handout on Digital Electronics found on the course website. II. Learning Objectives Using transistors and resistors, you'll

More information

Finite State Machine Lab

Finite State Machine Lab Finite State Machine Module: Lab Procedures Goal: The goal of this experiment is to reinforce state machine concepts by having students design and implement a state machine using simple chips and a protoboard.

More information

Physics 120/220 Lab Equipment, Hints & Tips

Physics 120/220 Lab Equipment, Hints & Tips Physics 120/220 Lab Equipment, Hints & Tips Solderless Breadboard... 2 Power supply... 4 Multimeters... 5 Function generator... 5 Oscilloscope... 6 10X probe... 7 Resistor color code... 7 Components...

More information

PB-501. Logic Design Trainer Instruction Manual

PB-501. Logic Design Trainer Instruction Manual PB-501 Logic Design Trainer Instruction Manual 10/2009 2 All rights reserved. No Part of this book shall be reproduced, stored in a retrieval system, or transmitted by any means, electronic, mechanical,

More information

E85: Digital Design and Computer Engineering Lab 1: Electrical Characteristics of Logic Gates

E85: Digital Design and Computer Engineering Lab 1: Electrical Characteristics of Logic Gates E85: Digital Design and Computer Engineering Lab 1: Electrical Characteristics of Logic Gates Objective The purpose of this lab is to become comfortable with logic gates as physical objects, to interpret

More information

ARRL ETP Solder Hour Clock Kit Construction Manual

ARRL ETP Solder Hour Clock Kit Construction Manual ARRL ETP Solder 101 24-Hour Clock Kit Construction Manual Do a complete parts check cross checking the individual parts against the parts list. Pay particular attention to the color code for the resistors:

More information

CSC 258 lab notes, Fall 2003

CSC 258 lab notes, Fall 2003 CSC 258 lab notes, Fall 2003 Instructor: E. R. C. Hehner Lab demonstrators: Nicolas Kokkalis, Andrés Lagar Cavilla Successful completion of the three graded labs in this course involves a significant amount

More information

ECE 270 Lab Verification / Evaluation Form. Experiment 1

ECE 270 Lab Verification / Evaluation Form. Experiment 1 ECE 70 Lab Verification / Evaluation Form Experiment Evaluation: IMPORTANT! You must complete this experiment during your scheduled lab period. All work for this experiment must be demonstrated to and

More information

Lab 0: Wire Wrapping Project: Counter Board

Lab 0: Wire Wrapping Project: Counter Board Lab 0: Wire Wrapping Project: Counter Board September 3, 2008 In this experiment, you will build a simple counter circuit that can be plugged into your breadboard. It will provide a set of TTL output signals

More information

Lab 4: Digital Electronics Innovation Fellows Program Boot Camp Prof. Steven S. Saliterman

Lab 4: Digital Electronics Innovation Fellows Program Boot Camp Prof. Steven S. Saliterman Lab 4: Digital Electronics Innovation Fellows Program Boot Camp Prof. Steven S. Saliterman Exercise 4-1: Familiarization with Lab Box Contents & Reference Books 4-1-1 CMOS Cookbook (In the bookcase in

More information

EECE 2411/2211-Introduction to Electrical and Computer Engineering Lab. Lab 3

EECE 2411/2211-Introduction to Electrical and Computer Engineering Lab. Lab 3 EECE 2411/2211-Introduction to Electrical and Computer Engineering Lab Lab 3 Building Multi-Gate Logic Circuits Introduction: In this lab we will look at combining the simple logic gates we used in the

More information

To connect the AC adapter:

To connect the AC adapter: Replacing the AC Adapter Replacing the AC Adapter 3 Plug the power cord into a wall outlet. The power indicator turns on. To connect the AC adapter: Connect the power cord to the AC adapter. Power indicator

More information

Lab 4: Digital Electronics BMEn 2151 Introductory Medical Device Prototyping Prof. Steven S. Saliterman

Lab 4: Digital Electronics BMEn 2151 Introductory Medical Device Prototyping Prof. Steven S. Saliterman Lab 4: Digital Electronics BMEn 2151 Introductory Medical Device Prototyping Prof. Steven S. Saliterman Exercise 4-1: Familiarization with Lab Box Contents & Reference Books 4-1-1 CMOS Cookbook (In the

More information

NAND/NOR Logic Gate Equivalent Training Tool Design Document. Team 34 TA: Xinrui Zhu ECE Fall Jeremy Diamond and Matthew LaGreca

NAND/NOR Logic Gate Equivalent Training Tool Design Document. Team 34 TA: Xinrui Zhu ECE Fall Jeremy Diamond and Matthew LaGreca NAND/NOR Logic Gate Equivalent Training Tool Design Document Team 34 TA: Xinrui Zhu ECE 445 - Fall 2017 Jeremy Diamond and Matthew LaGreca Table of Contents 1.0 INTRODUCTION 1.1 Objective 1.2 Background

More information

COS 116 The Computational Universe Laboratory 7: Digital Logic I

COS 116 The Computational Universe Laboratory 7: Digital Logic I COS 116 The Computational Universe Laboratory 7: Digital Logic I In this lab you ll construct simple combinational circuits in software, using a simulator, and also in hardware, with a breadboard and silicon

More information

Single cable kit for the FCB1010

Single cable kit for the FCB1010 Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing

More information

Using solderless breadboards

Using solderless breadboards Page 1 of 9 Using solderless breadboards This document describes how to use the solderless breadboards available in the experimental didactic lab (LED, previously LADISPE) of Politecnico di Torino. 1 Setting

More information

MIT Nerd Kit. Configurable Application Modules. Switches

MIT Nerd Kit. Configurable Application Modules. Switches MIT 6.004 Nerd Kit MIT 6.004 Nerd Kit comes with an array of 16 computational blocks. You can configure these blocks to do anything from computing just ANDs and ORs to being a Beta microprocessor. In addition

More information

DM-918 OPERATIONS MANUAL AUTORANGING MULTIMETER

DM-918 OPERATIONS MANUAL AUTORANGING MULTIMETER DM-918 OPERATIONS MANUAL AUTORANGING MULTIMETER SAFETY INFORMATION The following safety information must be observed to ensure maximum personal safety during the operation of this meter: This meter is

More information

EECS 140 Laboratory Exercise 4 3-to-11 Counter Implementation

EECS 140 Laboratory Exercise 4 3-to-11 Counter Implementation EECS 140 Laboratory Exercise 4 3-to-11 Counter Implementation 1. Objectives A. To apply knowledge of combinatorial design. B. Gain expertise in designing and building a simple combinatorial circuit This

More information

Infrared Add-On Module for Line Following Robot

Infrared Add-On Module for Line Following Robot 1 Infrared Add-On Module for Line Following Robot January 3, 2015 Jeffrey La Favre The infrared add-on module allows multiple line following robots to operate on the same track by preventing collisions

More information

Lab 16: Data Busses, Tri-State Outputs and Memory

Lab 16: Data Busses, Tri-State Outputs and Memory Lab 16: Data Busses, Tri-State Outputs and Memory UC Davis Physics 116B Rev. 0.9, Feb. 2006 1 Introduction 1.1 Data busses Data busses are ubiquitous in systems which must communicate digital data. Examples

More information

K8099 NIXIE CLOCK. * optional enclosure TKOK19 (black) - TKOK17 (white) ** optional plexiglass enlcosure B8099 ILLUSTRATED ASSEMBLY MANUAL

K8099 NIXIE CLOCK. * optional enclosure TKOK19 (black) - TKOK17 (white) ** optional plexiglass enlcosure B8099 ILLUSTRATED ASSEMBLY MANUAL Total solder points: 230 + 74 Difficulty level: beginner 1 2 3 4 5 advanced NIXIE CLOCK K8099 ** * A unique combination of both vintage and modern electronics ILLUSTRATED ASSEMBLY MANUAL H8099IP-1 * optional

More information

A B A+B

A B A+B ECE 25 Lab 2 One-bit adder Design Introduction The goal of this lab is to design a one-bit adder using programmable logic on the BASYS board. Due to the limitations of the chips we have in stock, we need

More information

Copyright 2014, R. Eckweiler & OCARC, Inc. Page 1 of 6

Copyright 2014, R. Eckweiler & OCARC, Inc. Page 1 of 6 HOM rev. new Heathkit of the Month: by Bob Eckweiler, AF6C Heathkit of the Month #52 - SK-211 AC Monitor Heathkit SK-211 AC Monitor Introduction: When club president, Nicholas - AF6CF, mentioned he had

More information

Autoranging True RMS Multimeter User Manual

Autoranging True RMS Multimeter User Manual Autoranging True RMS Multimeter User Manual Please read this manual before switching the unit on. Important safety information inside. Contents Page 1. Safety Information... 4 2. Safety Symbols... 5 3.

More information

SPECIAL INSTRUCTIONS FOR CAPACITORS COMPACT GENERATORS

SPECIAL INSTRUCTIONS FOR CAPACITORS COMPACT GENERATORS SPECIAL INSTRUCTIONS FOR CAPACITORS COMPACT GENERATORS (WITH CAPACITOR CHARGER BOARD A3517-02) The process depends on Generator and System configuration. This document applies to installation of Capacitors

More information

PAD ANALOG / DIGITAL TRAINER OPERATOR S MANUAL

PAD ANALOG / DIGITAL TRAINER OPERATOR S MANUAL PAD - 234 ANALOG / DIGITAL TRAINER OPERATOR S MANUAL Rev. 7/94 GENERAL OPERATING PROCEDURES 1. This manual should be read thoroughly before engaging in any experimentation. 2. As a general rule, NEVER

More information

Diagnostics of Genie / Sauer Danfoss Joystick Controllers Deutsch type connection

Diagnostics of Genie / Sauer Danfoss Joystick Controllers Deutsch type connection Diagnostics of Genie / Sauer Danfoss Joystick Controllers Deutsch type connection Tools needed: Multi-meter Small Screwdriver Harness Adaptor 119613 Jumper Wires w/clips Three 1.5 volt AA or AAA Batteries

More information

The mystem Project Board Quick Start

The mystem Project Board Quick Start The mystem Project Board Quick Start This activity will introduce you to the basic functions of the mystem Project Board to get you started. Introduction to the mystem The mystem Project Board is designed

More information

LED Knight Rider. Yanbu College of Applied Technology. Project Description

LED Knight Rider. Yanbu College of Applied Technology. Project Description LED Knight Rider Yanbu College of Applied Technology Project Description This simple circuit functions as a 12 LED chaser. A single illuminated LED 'walks' left and right in a repeating sequence, similar

More information

Nvidia Quadro FX 5600 graphics card and auxiliary power adapter cable installation

Nvidia Quadro FX 5600 graphics card and auxiliary power adapter cable installation Nvidia Quadro FX 5600 graphics card and auxiliary power adapter cable installation HP xw8600 and xw9400 Workstations This document describes how to install an Nvidia Quadro FX 5600 graphics card and an

More information

GEORGIA INSTITUTE OF TECHNOLOGY School of Electrical and Computer Engineering ECE 2020 Fall 2017 Lab #1: Digital Logic Module

GEORGIA INSTITUTE OF TECHNOLOGY School of Electrical and Computer Engineering ECE 2020 Fall 2017 Lab #1: Digital Logic Module GEORGIA INSTITUTE OF TECHNOLOGY School of Electrical and Computer Engineering ECE 2020 Fall 2017 Lab #1: Digital Logic Module GOAL To introduce the physical implementation of digital logic circuits including

More information

Copyright 2011 R.S.R. Electronics, Inc. All rights reserved. 04/11. Ver. 1.0web

Copyright 2011 R.S.R. Electronics, Inc. All rights reserved. 04/11. Ver. 1.0web For XILINX WebPack Copyright 2011 R.S.R. Electronics, Inc. All rights reserved. 04/11 Ver. 1.0web 1 Table of Contents 1.0 INTRODUCTION...3 2.0 GENERAL DESCRIPTION...5 3.0 BRIEF DESCRIPTION Of PLDT-3 BOARD...6

More information

Model 2460-KIT. Screw Terminal Connector Kit. Description / September 2014 *P * 1

Model 2460-KIT. Screw Terminal Connector Kit. Description / September 2014 *P * 1 Keithley Instruments 28775 Aurora Road Cleveland, Ohio 44139 1-800-935-5595 http://www.keithley.com Model 2460-KIT Screw Terminal Connector Kit Description The Model 2460-KIT Screw Terminal Connector Kit

More information

Toshiba Satellite A210 Motherboard

Toshiba Satellite A210 Motherboard Toshiba Satellite A210 Motherboard Replacement In this guide you will learn how to properly remove the Motherboard. Written By: Devin ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Before

More information

GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000

GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000 GV3000/SE AC Drive ControlNet Network Communication Option Board M/N 2CN3000 Instruction Manual D2-3390-2 The information in this manual is subject to change without notice. Throughout this manual, the

More information

Instruction Manual. 2in1 LAN Tester & Multimeter. Model: 57314

Instruction Manual. 2in1 LAN Tester & Multimeter. Model: 57314 Instruction Manual 2in1 LAN Tester & Multimeter Model: 57314 1 Contents Introduction... Features... Safety Precautions.. Meter Description... Electrical Specification... Operation.. AutoRanging Multimeter.

More information

Memory (RAM) Replacement Instructions. apple PowerBook (FireWire) Tools Required. Electrostatic Discharge (ESD)

Memory (RAM) Replacement Instructions. apple PowerBook (FireWire) Tools Required. Electrostatic Discharge (ESD) apple PowerBook (FireWire) Memory (RAM) Replacement Instructions Be sure to follow these instructions carefully. Failure to follow these instructions could result in damage to your equipment and may void

More information

Agilent 3630A Triple DC Power Supply. Agilent 34401A Digital Multimeter (DMM)

Agilent 3630A Triple DC Power Supply. Agilent 34401A Digital Multimeter (DMM) Agilent E3630A Triple DC Power Supply and Agilent 34401A Digital Multimeter (DMM) Agilent 3630A Triple DC Power Supply The DC power supply used in this lab is the Agilent E3630A Triple DC power supply.

More information

OPERATING INSTRUCTION

OPERATING INSTRUCTION OPERATING INSTRUCTION AUTORANGING MULTIMETER MAX Ω F C 10A MAX every 15 min. COM V SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation

More information

Quicksilver 606 TR-606 CPU Upgrade

Quicksilver 606 TR-606 CPU Upgrade Quicksilver 606 TR-606 CPU Upgrade D650C 128 Installation Guide Social Entropy Electronic Music Instruments TABLE OF CONTENTS WARNINGS... 1 OVERVIEW... 2 WHAT'S IN THE BOX... 3 OPENING THE TR-606 CASE...

More information

Assembling the Printed Circuit Board for the EDE1200 Robot

Assembling the Printed Circuit Board for the EDE1200 Robot This board receives instructions from either a CBL2, a LabPro or (with an adapter cable) an original CBL. The board has two 595 shift registers (each providing 8 bits of on-board memory) and two EDE1200

More information

Freeze the Dizz Jameco Part No

Freeze the Dizz Jameco Part No Freeze the Dizz Jameco Part No. 2161431 This project is based on a children s arcade game. Twenty LEDs are placed on a ring and each takes turn to light up forming a rotating light spot. If a push-button

More information

Electronics & Control

Electronics & Control Engineering Science Electronics & Control Logic Page 2 Introduction Electronic circuits can be use to control a huge variety of systems but in each case there are IN- PUTS, PROCESSES and OUTPUTS. In this

More information

Electronic Balance Ionizer STABLO-AP Service Manual

Electronic Balance Ionizer STABLO-AP Service Manual 321-78209 Jan. 2016 Electronic Balance Ionizer STABLO-AP Service Manual Analytical & Measuring Instruments Division This page is intentionally left blank. Table of Contents 1. Precautions for Troubleshooting...

More information

Models 1417 and 1437 User s Manual. High-Speed Photodetector Modules

Models 1417 and 1437 User s Manual. High-Speed Photodetector Modules Models 1417 and 1437 User s Manual High-Speed Photodetector Modules Handling Precautions The detector is sensitive to electrostatic discharges and could be permanently damaged if subjected even to small

More information

4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials..

4.1 Parts and Components... IV Assembly Tips... IV Assembly Precautions... IV Required Tools, Equipment and Materials.. IV PERSONALITY MODULE ASSEMBLY 4.1 Parts and Components............ IV-1 4.2 Assembly Tips............... IV-1 4.3 Assembly Precautions............ IV-1 4.4 Required Tools, Equipment and Materials.. IV-1

More information

Experiment 9: Binary Arithmetic Circuits. In-Lab Procedure and Report (30 points)

Experiment 9: Binary Arithmetic Circuits. In-Lab Procedure and Report (30 points) ELEC 2010 Laboratory Manual Experiment 9 In-Lab Procedure Page 1 of 7 Experiment 9: Binary Arithmetic Circuits In-Lab Procedure and Report (30 points) Before starting the procedure, record the table number

More information

Dell Inspiron XPS and Inspiron 9100 Service Manual

Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Dell Inspiron XPS and Inspiron 9100 Service Manual Before You Begin Memory Module, Mini PCI Card, and Devices System Components Subwoofer Bluetooth Card

More information

DM3058/DM3058E Digital Multimeter

DM3058/DM3058E Digital Multimeter Quick Guide RIGOL Publication number QGA03109-1110 Feb. 2014 DM3058/DM3058E Digital Multimeter 2008 RIGOL Technologies, Inc. All Rights Reserved Copyright 2008 RIGOL Technologies, Inc. All Rights Reserved.

More information

S-14 S-14. Compact Digital Multimeter. Compact Digital Multimeter

S-14 S-14. Compact Digital Multimeter. Compact Digital Multimeter S-14 Compact Digital Multimeter S-14 Compact Digital Multimeter SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation at this meter

More information

HARDWARE OPERATIONS MANUAL

HARDWARE OPERATIONS MANUAL HARDWARE OPERATIONS MANUAL Table of Contents INTRODUCTION... 2 SECTION 1: HARDWARE COMPONENT ASSEMBLIES... 2 MECHANICAL HARDWARE AND CASE... 2 PCB ASSEMBLY... 4 ISD RECORDING CIRCUIT... 5 BREADBOARD ASSEMBLY...

More information

Network Controller. Installation/Troubleshooting Instructions NK220 COM1131C

Network Controller. Installation/Troubleshooting Instructions NK220 COM1131C Network Controller NK220 COM1131C Installation/Troubleshooting Instructions Part No. 70399101R4 October 2009 Table of Contents Getting Started... 2 Components of Network Controller... 2 System Overview...

More information

Pololu 12V Step-Up/Step-Down Voltage Regulator S10V2F12

Pololu 12V Step-Up/Step-Down Voltage Regulator S10V2F12 Pololu 12V Step-Up/Step-Down Voltage Regulator S10V2F12 Overview The Pololu step-up/step-down voltage regulator S10V2F12 is a switching regulator (also called a switched-mode power supply (SMPS) or DC-to-DC

More information

Treadmill Embedded Touch Screen Won t Power Up

Treadmill Embedded Touch Screen Won t Power Up Treadmill Embedded Touch Screen Won t Power Up E-TRe and E-TRxe This document contains the necessary information to troubleshoot a treadmill with an embedded touch screen that will not power up. Follow

More information

MODEL 9386 MULTI-SPORT TIMER

MODEL 9386 MULTI-SPORT TIMER MODEL 9386 MULTI-SPORT TIMER Instruction Manual Address: 34 Main Street, Whitesboro, NY 13492 Phone: 315-736-3967 Toll Free: 800-383-6060 Fax: 315-736-4058 SCOREBOARDS TIMERS MESSAGE SIGNS VIDEO DISPLAYS

More information

ELECTRONIC INSTRUMENTATION AND SYSTEMS LABORATORY

ELECTRONIC INSTRUMENTATION AND SYSTEMS LABORATORY ELECTRONIC INSTRUMENTATION AND SYSTEMS LABORATORY DEPARTMENT OF ELECTRICAL AND COMPUTER ENGINEERING MICHIGAN STATE UNIVERSITY I. TITLE: Lab IX - Light Activated Exhaust Fan II. PURPOSE: One use of bipolar

More information

Button Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System

Button Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept

More information

!There are two kit models. The ZCTK-120 is designed to operate with.!the pulse output is isolated from the mains line voltage. A pull-up resistor

!There are two kit models. The ZCTK-120 is designed to operate with.!the pulse output is isolated from the mains line voltage. A pull-up resistor CAUTION: Please make sure you have or have access to the skills necessary to assemble and use this product. Always secure the case with the included screws before applying electrical power to the power

More information

into the EMU E4 Classic and E4 Platinum Samplers

into the EMU E4 Classic and E4 Platinum Samplers Installing the CF-CARD SCSI Card Reader/Writer Drive into the EMU E4 Classic and E4 Platinum Samplers Thank you for purchasing the CF-CARD Internal Card Reader Drive Installation Kit from SCSICardReaders.com.

More information

User's Guide. MiniTec TM Series Model MN25 MultiMeter

User's Guide. MiniTec TM Series Model MN25 MultiMeter User's Guide MiniTec TM Series Model MN25 MultiMeter Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment (a

More information

Building the VMW Time Circuitry Meter by Vincent M. Weaver 6 May 2014

Building the VMW Time Circuitry Meter  by Vincent M. Weaver 6 May 2014 Building the VMW Time Circuitry Meter http://www.deater.net/weave/vmwprod/hardware/time_circuit/ by Vincent M. Weaver 6 May 2014 1 Introduction This is a work in progress. I will update it as I complete

More information

Installation Guide. HP J2437A 4-Port Token Ring Interface for the HP Router 650

Installation Guide. HP J2437A 4-Port Token Ring Interface for the HP Router 650 Guide HP J2437A 4-Port Token Ring Interface for the HP Router 650 Copyright Hewlett-Packard Company 1994. All rights reserved. Publication Number 5962-8322 Edition 1, August 1994 Printed in USA Product

More information

Validator Update Instructions for Rowe BC1200 $1 - $20

Validator Update Instructions for Rowe BC1200 $1 - $20 Validator Update Instructions for Rowe BC1200 $1 - $20 Kit Overview The purpose of the kit is to replace the Rowe BA50 transport and stacker with a 120 volt Mars validator with a compact mask. The kit

More information

Bill of Materials: Programming Interface for AVR PART NO

Bill of Materials: Programming Interface for AVR PART NO Programming Interface for AVR PART NO. 2174664 "Programmers" for the AVR family of microcontrollers actually terminate in a 6-pin header socket, with no convenient means to directly connect to the chip

More information

2 in1 LAN Tester & Multimeter. Model: PCE-LT 1

2 in1 LAN Tester & Multimeter. Model: PCE-LT 1 www.pce-industrial-needs.com Tursdale Technical Services Ltd Unit N12B Tursdale Business Park Co. Durham DH6 5PG United Kingdom Phone: +44 ( 0 ) 191 377 3398 Fax: +44 ( 0 ) 191 377 3357 info@tursdaletechnicalservices.co.uk

More information

Upgrading and Servicing Guide

Upgrading and Servicing Guide Upgrading and Servicing Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed

More information

Pacific Antenna Two Tone Generator

Pacific Antenna Two Tone Generator Pacific Antenna Two Tone Generator Description Our Two Tone Generator kit provides two non-harmonic, sine wave signals for testing audio circuits Outputs of approximately 700Hz and 1900Hz and the combination

More information

Electronics Construction Manual

Electronics Construction Manual Electronics Construction Manual MitchElectronics 2018 Version 1 07/05/2018 www.mitchelectronics.co.uk CONTENTS Introduction 3 How To Solder 4 Resistors 5 Capacitors 6 Diodes and LEDs 7 Switches 8 Transistors

More information

This presentation will..

This presentation will.. Component Identification: Digital Introduction to Logic Gates and Integrated Circuits Digital Electronics 2014 This presentation will.. Introduce transistors, logic gates, integrated circuits (ICs), and

More information

MTP INSTRUCTION MANUAL

MTP INSTRUCTION MANUAL DT-118B MTP INSTRUCTION MANUAL Pocket Autoranging Digital Multimeter 3 in 1 Model MTP-1025 Auto Ran ging DMM Hz% A OFF V AU TO PO WER OFF MTP Instruments Table of Contents Introduction Page 1 Features

More information

Upgrading and Servicing Guide

Upgrading and Servicing Guide Upgrading and Servicing Guide The information in this document is subject to change without notice. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not

More information

LCD Prototype Circuit on Solderless Breadboard. 840 Pin Solderless Breadboard (http://www.digikey.com/ # ND)

LCD Prototype Circuit on Solderless Breadboard. 840 Pin Solderless Breadboard (http://www.digikey.com/ # ND) Solderless Breadboard Tutorial Cornerstone Electronics Technology and Robotics I Week 3 Solderless Breadboards: o Solderless breadboards are commonly used in experimentation or to make a prototype of a

More information

LINE VOLTAGE TESTER CT101 USER S MANUAL. Please read this manual carefully and thoroughly before using this product.

LINE VOLTAGE TESTER CT101 USER S MANUAL. Please read this manual carefully and thoroughly before using this product. LINE VOLTAGE TESTER USER S MANUAL CT101 Please read this manual carefully and thoroughly before using this product. KEY FEATURES Visual indication of AC or DC voltage Easy to use approved Safe for CAT

More information

Phillips Screwdriver. Some C-128's may need a TORX ("star" point) driver (size T10)f available at Sears, and other hardware and automotive stores.

Phillips Screwdriver. Some C-128's may need a TORX (star point) driver (size T10)f available at Sears, and other hardware and automotive stores. C-128 INSTALLATION Required Tools: Phillips Screwdriver. Some C-128's may need a TORX ("star" point) driver (size T10)f available at Sears, and other hardware and automotive stores. IC extractor or small,

More information

Physics E-1bxl and PS3 Lab 4: Neuron Model 2016

Physics E-1bxl and PS3 Lab 4: Neuron Model 2016 I. Before coming to lab Read this handout. Also review the background supplemental for Lab 3:Digital Circuits especially the sections on breadboard layout, transistors, and LEDs. Carefully study the circuit

More information

Chapter 19. Floppy Disk Controller Discussion. Floppy Disk Controller 127

Chapter 19. Floppy Disk Controller Discussion. Floppy Disk Controller 127 Floppy Disk Controller 127 Chapter 19 Floppy Disk Controller 19-1. Discussion Without some "mass storage" device such as a floppy disk, even the largest computer would still be just a toy. The SK68K can

More information

1/Build a Mintronics: MintDuino

1/Build a Mintronics: MintDuino 1/Build a Mintronics: The is perfect for anyone interested in learning (or teaching) the fundamentals of how micro controllers work. It will have you building your own micro controller from scratch on

More information

HP UPS R/T3000 ERM. Overview. Precautions. Installation Instructions

HP UPS R/T3000 ERM. Overview. Precautions. Installation Instructions HP UPS R/T3000 ERM Installation Instructions Overview The ERM consists of two battery packs in a 2U chassis. The ERM connects directly to a UPS R/T3000 or to another ERM. Up to two ERM units can be connected.

More information

EE 354 August 1, 2017 Assembly of the AT89C51CC03 board

EE 354 August 1, 2017 Assembly of the AT89C51CC03 board EE 354 August 1, 2017 Assembly of the AT89C51CC03 board The AT89C51CC03 board comes as a kit which you must put together. The kit has the following parts: No. ID Description 1 1.5" x 3.25" printed circuit

More information

SMART Multisensory Fitness Training. Technical Service Manual For the SMART Trainer Systems Revision 1.5.2

SMART Multisensory Fitness Training. Technical Service Manual For the SMART Trainer Systems Revision 1.5.2 SMART Multisensory Fitness Training Technical Service Manual For the SMART Trainer Systems Revision 1.5.2 2014 Unlike other fitness equipment which may require additional insurance, SMART ProTrainer and

More information

Introduction to Electronics Workbench

Introduction to Electronics Workbench Introduction to Electronics Workbench Electronics Workbench (EWB) is a design tool that provides you with all the components and instruments to create board-level designs on your PC. The user interface

More information

Arduino 05: Digital I/O. Jeffrey A. Meunier University of Connecticut

Arduino 05: Digital I/O. Jeffrey A. Meunier University of Connecticut Arduino 05: Digital I/O Jeffrey A. Meunier jeffm@engr.uconn.edu University of Connecticut About: How to use this document I designed this tutorial to be tall and narrow so that you can read it on one side

More information

Board Of Education USB (#28850)

Board Of Education USB (#28850) 599 Menlo Drive, Suite 100 Rocklin, California 95765, USA Office: (916) 624-8333 Fax: (916) 624-8003 Sales: sales@parallax.com 1-888-512-1024 Tech Support: support@parallax.com 1-888-99-STAMP Web Site:

More information

Experimental Procedure

Experimental Procedure 1 of 14 9/10/2018, 11:38 AM https://www.sciencebuddies.org/science-fair-projects/project-ideas/robotics_p028/robotics/obstacle-avoiding-robot (http://www.sciencebuddies.org/science-fair-projects /project-ideas/robotics_p028/robotics/obstacle-avoiding-robot)

More information

imac Intel 27" Retina 5K Display SATA Cable

imac Intel 27 Retina 5K Display SATA Cable imac Intel 27" Retina 5K Display SATA Cable Replacement Written By: Dozuki System 2017 guides.crucial.com Page 1 of 32 INTRODUCTION Use this guide to replace the SATA cable on the back of the logic board

More information

A4988 Stepper Motor Driver Carrier, Black Edition

A4988 Stepper Motor Driver Carrier, Black Edition A4988 Stepper Motor Driver Carrier, Black Edition A4988 stepper motor driver carrier, Black Edition, bottom view with dimensions. Overview This product is a carrier board or breakout board for Allegro

More information

QUASAR KIT No DIGITAL DOWN TIMER 99 MIN WITH PIC

QUASAR KIT No DIGITAL DOWN TIMER 99 MIN WITH PIC QUASAR KIT No 1173 - DIGITAL DOWN TIMER 99 MIN WITH PIC KIT 1173 is a digital countdown timer based on a micro controller, thus securing reliability and excellent operation under any circumstances. It

More information

Abstract. GLV User Manual 1

Abstract. GLV User Manual 1 GLV User Manual 1 Abstract This user manual is a high level document that explains all operational procedures and techniques needed to operate the GLV system in a safe and effective manner. Anyone operating

More information

Pianocorder Audio Interface Kit Installation Guide

Pianocorder Audio Interface Kit Installation Guide Pianocorder Audio Interface Kit Installation Guide Mark Fontana Last updated 9/12/2016 Introduction The Pianocorder Audio Interface enables you to modernize your 1970s Marantz

More information

Mini Digital Multimeter

Mini Digital Multimeter User's Guide Mini Digital Multimeter Model MN15 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Back to the Extech MN15/MN16 Series

More information

GV3000/SE Operator Interface Module (OIM) User Guide Version 2.0 M/N 2RK3000

GV3000/SE Operator Interface Module (OIM) User Guide Version 2.0 M/N 2RK3000 GV3000/SE Operator Interface Module (OIM) User Guide Version 2.0 M/N 2RK3000 Instruction Manual D2-3342-2 The information in this manual is subject to change without notice. Throughout this manual, the

More information

Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com.

Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com. Thank you for purchasing this Factory Service Manual CD/DVD from servicemanuals4u.com. Please check out our ebay auctions for more great deals on Factory Service Manuals: servicemanuals4u Dell Latitude

More information

Upgrading and Servicing Guide

Upgrading and Servicing Guide Upgrading and Servicing Guide Copyright Information The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing

More information

2 in 1 LAN Tester and Multimeter Model:

2 in 1 LAN Tester and Multimeter Model: 2 in 1 LAN Tester and Multimeter Model: 72-8495 1 IMPORTANT SAFETY INFORMATION Please read these instructions carefully before use and retain for future reference. This instrument is designed and manufactured

More information

Breakout Card For Z50Bus User Guide

Breakout Card For Z50Bus User Guide Breakout Card For Z50Bus User Guide For card: SC117 version 1.0 Design and Documentation by Stephen C Cousins Edition 1.0.0 CONTENTS OVERVIEW...2 PRINTED CIRCUIT BOARD... 4 SCHEMATIC... 5 WHAT YOU NEED...6

More information