Sensing method Appearance Connection method Sensing distance Output Model. M12 connector 10±3 mm. Size Type Appearance Cable length Model Straight

Transcription

1 Color Photoelectric Sensor Color Detection on Any Type of Packaging. Narrow Beam and Large Lens for Stable Detection of Workpieces Tilted at Various Angles. Detects subtle color differences. High luminance, three-element (RGB) LED light source for greater light intensity. Highly efficient optics technology provides high power and enables stable detection even of subtle color differences. Handles glossy workpieces. Thorough noise reduction. High dynamic range covers everything from black to mirror surfaces. IoT compatible. Models that support IO-Link also available. Sends RGB information to host with high-speed IO-Link communications. Optimum threshold set to reduce false detection. For the most recent information on models that have been certified for safety standards, refer to your OMR website. Refer to Safety Precautions on page 6. Ordering Information Sensors (Refer to Dimensions on page 7.) light, light, light Sensing method Appearance Connection method Sensing distance Output Model Diffuse-reflective (mark detection) M connector ± mm Note: Please contact your OMR sales representative regarding the IO-Link setup file (IODD file). * Refer to Ratings and Specifications on page for the baud rate. Accessories (Sold Separately) Sensor I/O Connectors (Required for a Sensor with a connector.) Connectors are not provided with the Sensors. Be sure to order a Connector separately. IO-Link baud rate * COM P-IL (8. kbps) Push-pull COM P-IL (. kbps) NPN N Not supported Size Type Appearance Cable length Model Straight m XSF-D-D8-F M Socket on one cable end Socket and plug on cable ends * L-shape Smartclick connector Straight/straight Smartclick connector L-shape/L-shape 5 m XSF-D-G8-F m XSF-D-D8-F 5 m XSF-D-G8-F Note:. Refer to Sensor I/O Connectors/Sensor Controllers on your OMR website for details. The XSW (Socket and Plug on Cable Ends) and XS5F (Socket on One Cable End) are also available.. The connectors will not rotate after they are connected. *. There are also straight type/l-shape type combinations available. *. The cable is fixed at an angle of 8 from the sensor emitter/receiver surface. * * m XS5W-D-D8-F 5 m XS5W-D-G8-F m XS5W-D-D8-F 5 m XS5W-D-G8-F

2 Ratings and Specifications Sensing method Diffuse-reflective (mark detection) Output Push-pull NPN Item Model P-IL P-IL N Sensing distance Spot size (reference value) Light source (wavelength) Power supply voltage Power consumption Control output ± mm ( paper mm) mm LED (65 nm), LED (55 nm), LED (65 nm) to DC±% (Ripple (p-p) % max.) 96 mw max. (Reference: Power supply voltage V, Current consumption ma max.) current: ma max. (DC max.) Operation indicator (orange), (green), Indications 7-segment indicator (white), Key lock indicator (white), Timer indicator (white), -point teaching mode indicator (white) Operation mode High when mark is detected. when mark is detected. Protection circuits Response time Sensitivity adjustment Ambient illumination Ambient temperature range Ambient humidity range Insulation resistance Dielectric strength Vibration resistance Shock resistance Degree of protection Connection method Weight (packed state/sensor only) Materials Model with connector Case Lens Indicators Buttons Connector Power supply reverse polarity protection, output short-circuit protection and output incorrect connection protection Operate or reset: 5 μs max. for each (-point teaching mode) Operate or reset: 5 μs max. for each (-point teaching mode) Teaching method Incandescent lamp:, lx max. Operating: to 55 C; Storage: 5 to 7 C (with no icing or condensation) Operation: 5% to 85%, Storage: 5% to 95% (with no condensation) MΩ min. (at 5DC),AC, 5/6 Hz for min Destruction: to 55 Hz with double amplitude of.5 mm for hours each in X, Y, and Z directions Destruction: 5 m/s times each in X, Y, and Z directions IEC 659 IP67 M, -pin connector Approx. 7 g/approx. g Diecast zinc (nickel-plated brass) Methacrylic resin (PMMA) ABS Elastomers Diecast zinc (nickel-plated brass) Main IO-Link functions Operation mode switching between NO and NC Timer function of the control output and timer time selecting function (Select a function from disabled, delay, OFF delay, one-shot or /OFF delay.) (Select a timer time of -5 ms.) Selecting function of delay timer time for instability ( (disabled)- ms) Monitor output function (PD output indicating a relative detection quantity) Energizing time read-out function (unit: h) Initialize the settings function Restore the factory settings --- IO-Link specification Version. --- Communication specifications Accessories Baud rate P-IL: COM (. kbps), P-IL: COM (8. kbps) Data length PD size: 8 bytes, OD size: byte (M-sequence type: TYPE ) --- Minimum cycle time P-IL (COM):.5 ms, P-IL (COM):.8 ms --- Instruction manual * Standard Sensing Object for the Sensor Color --- Munsell code N9.5 R.5/ -red YR /.5 5Y 8.5/ GY 6.5/ G 6.5/ 5BG.5/ PB / -purple 9PB / 7P / -purple 6RP.5/.5 () (N.)

3 Engineering Data (Reference Value) Color vs. Detection Capability Teaching Capabilities -red -purple -purple -red -purple -purple Note: The above chart shows the combinations of colors for which teaching is possible at a sensing distance of mm. Detectable Ranges Background color: Background color: Background color: -red -red -purple -purple -red -purple -purple -purple -purple Background color: Background color: Background color: -red -purple -purple -red -purple -purple -red -purple -purple Background color: o Background color: -red -purple -purple -red -purple -purple Background color: -purple -red -purple

4 Background color: Background color: -purple Background color: -red -purple -purple Excess Gain vs. Distance Sensing object: paper -red -purple Sensing object: Aluminum vapor deposition film -red -purple -purple Distance (mm) Angle vs. Incident Characteristics 5 5 Sensing object: paper Distance (mm) Angle ( ) Sensing object: Aluminum vapor deposition film Angle ( )

5 I/O Circuit Diagrams Push-Pull Output Model Output mode NO/NC setting * Timing chart Output circuit P-IL P-IL Standard I/O mode (SIO mode) (Pin Output Settings) NO *5 NC Sensing object Background () Operation indicator Not Pin output (NO) Pin output (NO) current OFF (PNP connection) current (NPN connection) Sensing object Background () Operation indicator Pin output (NC) Pin output (NC) current (PNP connection) current OFF (NPN connection) OFF Not OFF Using Pin as an external input * (enabled by default) C/Q EXT/ OUT C/Q EXT/ OUT NPN * External input PNP * Using Pin with a control output * (set for IO-Link) PNP * NPN * to DC to DC IO-Link mode (Pin Output Settings) NO *5 NC Sensing object Background () ( sec cycles Flashing) Operation indicator Not Pin output (NO) (IO-Link communications) Pin output (NO) Sensing object Background () ( sec cycles Flashing) Operation indicator Pin output (NC) (IO-Link communications) Pin output (NC) *. Pin input/output can be switched with the IO-Link communication command Switchpoint Pin. *. In case of NPN connection, please connect the load between Pin and Pin. *. In case of PNP connection, please connect the load between Pin and Pin. *. It can be switched in IO-Link. *5. Factory default Note:. You can use IO-Link communications to reverse the operation logic, set an output delay, and change between an input and output.. Please contact your OMR sales representative regarding assignment of data. Not EXT/ OUT DI/DO V C/Q C/Q IO-Link Master NPN Output Model Timing chart Output circuit N Sensing object Background () Operation indicator Not Pin output (NO) OFF current OFF Q EXT External input to DC Plugs (Sensor I/O Connectors) M, -pin Connector Terminal number Wire color Application Wire Connector Classification color pin No. P-IL N P-IL Power supply () Power supply () External input * External input DC Power supply () Power supply () Output C/Q Control output * It can be set as the control output with IO-Link. 5

6 Nomenclature Operation indicator Turns when the mark is detected. (when Pin is set as NO) 7-segment indicator () Displays the BANK No. being selected. Key lock indicator () Turns when key locksetting is activated. Timer indicator () Turns when timersetting is activated. -point teaching mode indicator () Turns when -point teaching mode. () Turns while power is supplied. Blinks during IO-Link communication. Setup change [BANK] button Changes the BANK setting. (BANK NO.) Sensitivity setting (Background) [BKGD] button Executes the background teaching. Sensitivity setting () [MARK] button Executes the mark teaching. Safety Precautions Be sure to read the precautions for all models in the website at: Warning Indications WARNING Precautions for Safe Use Precautions for Correct Use Meaning of Product Safety Symbols Warning level Indicates a potentially hazardous situation which, if not avoided, will result in minor or moderate injury, or may result in serious injury or death. Additionally, there may be significant property damage. Supplementary comments on what to do or avoid doing, to use the product safely. Supplementary comments on what to do or avoid doing, to prevent failure to operate, malfunction or undesirable effect on product performance. General prohibition Indicates the instructions of unspecified prohibited action. Caution, explosion Indicates the possibility of explosion under specific conditions. Caution, fire Indicates the possibility of fire under specific conditions. General caution Indicates unspecified general alert. WARNING This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purpose. Never use the product with an AC power supply. Otherwise, explosion may result. Precautions for Safe Use The following precautions must be observed to ensure safe operation of the product.. Do not install the product in the following locations. Locations subject to direct sunlight Locations subject to condensation due to high humidity Locations subject to corrosive gas In the place where vibration or shock is directly transmitted to the product.. Do not use the product in environments subject to flammable or explosive gases.. Do not use the product in any atmosphere or environment that exceeds the ratings.. Do not pull on the cable with excessive strength. 5. Do not attempt to disassemble, repair, or modify the product in any way. 6. Do not use the product with the main unit damaged. 7. Be sure that before making supply the supply voltage is less than the maximum rated supply voltage (DC). 8. Do not apply any load exceeding the ratings. 9. Do not short the load. Otherwise damage or fire may result.. Connect the load correctly.. Do not use the product under a chemical or an oil environment without prior evaluation.. Though this is type IP67, do not use in the water, rain or outdoors.. Do not use thinner, alcohol, or other organic solvents. Otherwise, the optical properties and degree of protection may be degraded.. When disposing of the product, treat it as industrial waste. 5. These Sensors are certificated for the UL standard on the assumption of usage in a Class circuit. Use them with Class power supplies in the United States or Canada. Use the OMR XSF-D-series or XS5F-D-series Cables. Cables that have wires less than AWG (. mm ) are for connection to terminal blocks and are not for field splicing. External overcurrent protection of A for AWG6, A for AWG, or A for AWG wire must be provided for cable protection. Do not use the product with voltage in excess of the rated voltage. Excess voltage may result in malfunction or fire. Be sure to tighten the external lens until it reaches the chassis. 6

7 Precautions for Correct Use. Note that the water-resistant function is impaired if installing the Photoelectric Sensor by hitting it with a hammer and so on.. Be sure to tighten the external lens until it reaches the chassis.. If the Sensor wiring is placed in the same conduits or ducts as high-voltage or high-power lines, inductive noise may cause malfunction or damage. Wire the cables separately or use a shielded cable.. To extend a cable in the standard I/O mode, use a cable of. mm or more and keep the length m or less. Keep the length m or less if using the Sensor in the IO-Link mode. 5. Apply a screw tightening torque of. N m or less. 6. If a commercial switching regulator is used, ground the FG (frame ground) terminal. 7. The Sensor will be able to detect objects ms after the power supply is tuned. Start using the Sensor ms or more after turning the power supply. If the load and the Sensor are connected to separate power supplies, be sure to turn the Sensor first. 8. Do not press the button with anything sharp such as a screwdriver because it might be damaged. 9. Output pulses may occur when the power supply is turned OFF. We recommend that you turn OFF the power supply to the load or load line first. Dimensions Sensors (Unit: mm) Tolerance class IT6 applies to dimensions in this data sheet unless otherwise specified. Diffuse-reflective Models P-IL P-IL N The optical axis can be changed by swapping the lens and cover. The connector section can be revolved in a range of 9. Two, M5; Depth: 5.5 M connector When Lens or Cover Is Replaced Optical axis Optical axis dia. Outer diameter) Four, M5; Depth: dia. (lens diameter) Note:. Apply a screw tightening torque of. N m or less.. Be sure to tighten the external lens or cover until it reaches the chassis. 7