FREQUENCY CONVERTER FC102 (QUICK GUIDE)

Transcription

1 FREQUENCY CONVERTER FC102 (QUICK GUIDE) INSTALLATION AND MAINTENANCE Content Page Safety instructions 2 IT system 3x230VAC 2 Connections 3 Control unit (LCP) 4 Manual operation 4 Reverse the direction of rotation 4 More information 4 Wiring diagram 5 Basic configuration 6 PID regulation 7 FläktGroup DC_9325GB _R0 Specifications are subject to alteration without notice

2 2 Installation and maintenance SAFETY INSTRUCTIONS Check that the frequency converter is correctly connected to earth. Do not pull out the mains or motor contacts or other power connections when the frequency converter is connected to the power supply grid. Protect the user from mains voltage. Protect the motor against overload in accordance with national and local regulations. The leakage currents to earth exceed 3.5 ma, see Design guide. The [Off] button is not an isolator switch. It does not disconnect the frequency converter from the mains. WARNING! Warning high voltage The frequency converter is subject to highly dangerous voltages when it is connected to the mains. Incorrect installation of the motor or frequency converter can lead to material damage, serious personal injury or death. Follow the instructions in this manual as well as local and national provisions and safety regulations. Voltage (V) WARNING! Discharge time! Frequency converters have DC bus capacitors that can hold a charge even after the mains voltage has been disconnected. Prevent electrical hazards by disconnecting the mains voltage, disconnecting permanent magnet motors and DC bus supplies, including battery backup, UPS and DC bus connections for other frequency converters. Wait until the capacitors have fully discharged before carrying out maintenance or repairs. Read more about the discharge waiting times in the table below. Starting to service or repair the unit immediately after cutting the power supply, without waiting for the specified period, can lead to death or serious personal injury. Output range (kw) Minimum waiting time (min) WARNING! Installation at heights For installation at height, contact FläktGroup regarding PELV. TAKE CARE! Residual current device: This product can cause a direct current in the protective earth conductor. When using a residual current device as additional protection, use only a type B residual current device (delayed) on the input side of this product. See also Danfoss application note for the MN90G RCD. The protective earthing of the frequency converter and the use of RCDs must always follow national and local regulations. TAKE CARE! IT system (3x230VAC) When installing the FC102 on an isolated system (IT system, 3x230VAC) set parameter to [0] Off. Press [Main Menu] twice. Navigate using the [ ] [ ] and [OK] buttons until parameter is displayed (select 14 **, then 14 5* and lastly 14 50). Set this parameter to [0] Off.

3 Installation and maintenance 3 CONNECTIONS PRINCIPLE IMAGE BB Control unit (LCP) 2 RS 485 serial bus 3 Analogue I/O LCP contact 5 Analogue switches 6 Cable support/ PE earth 7 Earthing plate 8 Earth clamp Shielded cable earth clamp and cable support 10 Motor connection Relay 1 12 Relay 2 13 Brake and load distribution terminal 14 Mains connection 15 USB Serial bus, terminal switch 8 17 Digital I/O and 24 V Cover panel

4 Info 4 Installation and maintenance CONTROL UNIT (LCP) A. Alphanumeric display The information displayed in the control unit display (LCP) can be customised. See parameters 0 20, 0 21, 0 22, 0 23 and The factory settings display: motor rpm, motor current, motor output, motor frequency and reference. B. Menu buttons Use the menu buttons to access the parameter settings, to toggle between status display modes during normal operation and to display fault log data. a a Status 1(1) 1234rpm 1.0 A 43,5Hz Run OK 43,5Hz C. Navigation and indication [Back] returns to the previous step or menu list [Cancel] Cancel the latest change or command [Info] Provides information of the function displayed [ ] [ ] [ ] [ ] navigate and increase/decrease [OK] Activate selection or access a parameter group b Status Back Quick Menu Main Menu Cancel Alarm Log Green indication power on Yellow indication warning Red indication alarm c c On Warn. OK D. Driftslägesknappar och återställning [Hand/on] Starting the motor for local control [Off] Stopping the motor [Auto/on] Allow control via control terminals or the communication bus [Reset] Resetting alarms d Alarm Hand on Off Auto on Reset MANUAL OPERATION Press [Hand/on] to start Press the navigation buttons to set the desired speed Press [Off] to stop Press [Auto/on] to return to automatic operation REVERSE THE DIRECTION OF ROTATION If necessary the direction of rotation can be reversed using parameter When connection is correct 0=clockwise and 1=anti-clockwise. MORE INFORMATION This quick guide contains the basic information needed to install and operate the frequency converter. There is more information available in the attached documentation.

5 Installation and maintenance 5 WIRING DIAGRAM L1 L2 L3 N PE F L1 L2 L3 PE Danfoss FC V V 13 DIG IN 18 DIG IN 19 COM 20 DIG IN 27 DIG IN 29 DIG IN 32 DIG IN 33 DIG IN V 50 A IN 53 A IN 54 COM 55 A OUT 42 COM 39 R2 R Relay output 0 Alarm NO/NC (Param ) Relay output 1 Start Start Reference 0 10VDC (FW standard) Actual value PID regulation Run Indicator NO/NC (Param ) Analog switches A53 12 A54 12 ON ON ON = 0-20m OFF = 0-10VDC U V W PE RS-485 com 61 RS RS The basic configuration (FläktGroup standard) relates to VDC control via terminal block 53. M To activate the internal PID regulator see page 6. The sensor is connected to terminal block 54. SIGNALS Designation Type Terminal block Start Potential-free closure Control signal VDC 53 Pressure/flow sensor VDC (4...20mA) 54 COM For analogue in (Terminal blocks 53, 54) 55 Alarm R1 NO/NC 01, 02, 03 Operation R2 NO/NC 04, 05, 06

6 6 Installation and maintenance BASIC CONFIGURATION FOR ASYNCHRONOUS MACHINES (FLÄKTGROUP STANDARD) When the frequency converter is energized for the first time the language can be selected. Obviously this can be changed later. After Smart Start is started for VDC control by pressing [ ], followed by pressing [OK]. Step Description TF FF 1 Language English English 2 Select Q3 Function Setups Asynchronous Asynchronous 3 Number of motors Thermal motor protection ETR 1 ETR 1 5 Motor Power [kw] 6 Motor Voltage 7 Motor Current 8 Motor Frequency See motor plate 9 Motor Nominal Speed 10 Minimum Reference 0 Hz 0 Hz 11 Maximum Reference Hz Hz 12 Apply on terminal block 53 Yes Yes 13 Application Fan Fan 14 Autom Energy Optimisation Yes (2, 4-pon) Yes (2, 4-pin) No (other) No (other) See motor plate 15 AMA Yes Yes 16 Confirm AMA OK OK 17 Press [Main Menu] twice 18 Select 3-** Reference / Ramps 19 Select 3-4* Ramp 1 20 [3-41] Ramp 1, Ramp Up Time 21 [3-42] Ramp 1, Ramp Down Time 30s 40s When the frequency converter is energized for the first time the language can be selected. Obviously this can be changed later. After Smart Start is started for VDC control by pressing [ ], followed by pressing [OK]. When using CentriFlow 3D, you need to enter 1-06 and change the direction of rotation to [1] inverse. Configuration carried out by Date Smart Start can be reactivated at any time. First press [Quick Menus]. Then navigate using the [ ] and [ ] buttons until the cursor is on Q4 Smart Start. Then press [OK]. Danfoss factory reset Press [Main Menu] twice. Navigate using the [ ] [ ] and [OK] buttons until parameter is displayed (select 14 **, then 14 2* and lastly 14 22). Set this parameter to [2] and then switch off the mains voltage. When the frequency converter is re-energised the parameters will have returned to their factory settings.

7 Installation and maintenance 7 ACTIVATING PID REGULATION Step Description TF FF 1 Press [Quick menus] 2 Press [Quick menus] 3 Select Q3-3 Closed Loop Settings 4 Select Q3-30 Single Zone Int.Setpoint Confi guration Mode [3] Closed Loop [3] Closed Loop Reference/Feedback Unit [72] Pa [72] Pa Minimum Reference/Feedb. 0 Pa 0 Pa Maximum Reference/Feedb. Pa Pa 9 Press [ ] once Terminal 54 Low Ref./Feedb. 0 Pa 0 Pa Terminal 54 High Ref./Feedb. Pa Pa Terminal 54 Filter Time Const 1 s 1 s 14 Press [ ] four times Setpoint 1 Pa Pa PID Normal/Inverse Control [0] Normal [0] Normal See sensor See sensor Setpoint 17 Press [ ] twice PID Start Speed PID Proportional Gain 30.0s 30.0s Adjust if necessary 20 Press [Main Menu] twice 21 Select 0 ** Operation / Display 22 Select 0 2* LCP Display Display Line 1.1 Small [1654] Feedback 1 [1654] Feedback 1 Configuration carried out by Date

8 8 Installation and maintenance MODBUS RTU IN EQ If Modbus RTU is used in eq AHU for controlling drives, they must be set according to the table below. Configuration Parameter Description Value 8-30 Protocol [2] Modbus RTU 8-31 Address Supply fan: 60 Exhaust fan: Baudrate [2] Parity / Stop bits [2] No parity, 1 Stop bit PARALLEL OPERATION When two frequency converters are to operate in parallel, one must be configured as master and the other as slave. After this, connect the two frequency converters together as indicated below. Configuration, master Parameter Description TF FF 6-50 Function, terminal block mA 4-20mA Configuration, slave Parameter Description TF FF 6-14 Output frequency equivalent to 4mA 0 Hz 0 Hz 6-15 Output frequency equivalent to 20mA Hz Hz Set switch A53 (located under the display) to position I. The power to the converter must be switched off. Connection Master Slave