OPTOTRONIC OT 45/ /700 LTCS 700mA Constant Current LED Power Supply and DIPswitch

Transcription

1 data Reference: For LED modules: ma LED Nominal Voltage: V AC Line Current, nominal: V Mains Frequency: 50/60 Hz Protection Class: II Output Current: ma DC +/- 5% (350-) Output voltage: V DC maximum 120V DC Interface: Output Power: 45 W Partial Load 11W.. 45W, see load diagramm Rated Power factor: > 0,95 (full 230V > 0,85 (half 230V Power Loss: 6 W max. ECG efficiency: 89% full load at 230V Power Loss in standby mode < 1,5 W : turned off Input Voltage: VAC Permitted voltage range DC Voltage: No Internal Control No-load proof: Hot plug functionality: Short circuit protection: Overload protection: Overtemperature protection: Yes Yes Max turn-on delay after hot-plug = 25s Automatic, reversible Automatic, reversible Automatic, reversible Ambient temperature range, t a : -25 C to +50 C Max. case temperature at t c point: 90 C ECG Lifetime: h at t case = 80 C at t c point and 10% failure rate Maximum casing temperature in case 110 C of fault Page 1 of 6

2 Inrush current: Max. no. of circuit breakers 10 A (B type): Max. no. of circuit breakers 16 A (B type): Max. no. of circuit breakers 16 A (B type): in combination EBN-OS Terminal: Cable cross section input side Wire preparation length Input side: Cable cross section output side: 8 A t width = 55 µs (measured at 50% Ipeak) Mains (grey) Functional earth (grey) (grey [GNDset], purple [], blue [+12]) LEDModule ( [+] red/ [-] black) 0,2 mm² 1,5 mm² Solid and flexible 8,5 9,5 mm 0,2 mm² 1,5 mm² Solid and flexible, only 0,2mm 2 0,5mm 2 Wire preparation length output side: 8,5 9,5 mm Max. cable length - system: 2 m Geometry (l x b x h): 123 x 79 x 33 mm (K3) Weight: 240 g IP Code: IP20 Safety: Performance: Radio interference: Harmonic content: Immunity: IEC , IEC IEC EN 55015:2006+A1:2007+A2:2009 IEC IEC 61547:1995+A1:2000 Surge capability: L-N: 1,6kV, L/N Functional Earth: 2kV Galvanic isolation primary/secondary : 3,75 kvrms SELV-equivalent Approvals: Remark: An optional cable clamp is available. This cable clamp can be snapped onto the ECG and thus converts it into an ECG suitable for independent installation. Suitable cables are listed in cable clamp datasheet. EAN 10 (1 pc) EAN 40 (10 pcs) QT Cable Clamp K OTp Cable Clamp Page 2 of 6

3 Geometry Ordering information EAN 10 (1 pc) EAN 40 (20 pcs) Wiring diagram ~ L/N (PE/FE) DIP1 DIP2 on on DIPswitch 350mA/// LED GNDset ( Interface) LED Page 3 of 6

4 U-out [V] OPTOTRONIC : Output Characteristic Output Characteristics 120V 40-45W 35-40W 30-35W <30W A 38V B Iout [ma] [B] Nominal Operating Range, [A] + [B] Current Range DIPswitch DIP1 DIP2 Current Off Off Off On On Off On On 350mA interface allows to control the output current of the control gear (ref. to application note). The input voltage of the pin defines the output current relative to the maximum nominal current of the control gear. interface is not isolated to the secondary side of the LED driver output. +12 GNDset Auxiliary supply 12V +15/-8%, 15mA max. Signal input, included current source 274µA 0V < < 12V +15% Reference ground for +12 and Page 4 of 6

5 The relation between input voltage and output current is as following: 600mA Iout 400mA 300mA Protection region 200mA 100mA OFF 1V 3V 5V 7V 9V 11V Output current relative to the nominal current Iout [% of Imax]=(-1V)/(10V-1V) between Imin and Imax The output current could also be set in combination the DIPswitch current pre-selection (350,500 and ) and the interface. In those three operation modes the ECG does not switch off as soon as exceeds 11V (no protection region). DIP xx = Iout 600mA 400mA 300mA DIP xx = DIP xx = 350mA 200mA 100mA OFF 1V 3V 5V 7V 9V 11V Page 5 of 6

6 Power Factor Efficiency [%] OPTOTRONIC 100,0 Typical Efficiency and Power Factor versus Load 1,5 90,0 80,0 70,0 1,4 1,3 1,2 60,0 50,0 40,0 30,0 20,0 10,0 350mA 350mA 1,1 1,0 0,9 0,8 0,7 0,6 0,0 0,0 5,0 10,0 15,0 20,0 25,0 30,0 35,0 40,0 45,0 Output Power [W] 0,5 Earth connection Earth connection is not required but may be used to improve EMI performance of the installation Wrong wiring This control gear is inherently protected against wrong wiring. The wrong connections between LED+ and GNDset could damage irreversibly the ECG. All the other wrong wirings on the secondary side, once removed, make the ECG work regularly. LED- and GNDset terminals cannot be connected together. Installation notes The luminaire manufacturer is responsible for providing the required clearances and creepage distances and also for the protection against electrical shock, especially for the line and load wires according EN Instruction sheet Please consult the instruction sheet for further important information on e.g. wire stripping and wiring limitations in system installations. The instruction sheet is enclosed the device or available upon request. Page 6 of 6