General Description: Specification: wdmlighting.com

Transcription

1 General Description: Front View The 400 Watt 24V RGB Controller has programmable variations of speed, flash and fade time of each pattern, capable of fading between 2 seconds, variable to 2 minutes. It has selectable RGB dimming modes, RGB roll mode, auto-run, DMX mode, slave mode, sound controlled mode, and special control mode. The total power consumption for all LED lights connected is 400 Watts. Connect up to 164 feet of RGB Rope or 65 ft. of Cove Lighting to this power supply. Additional units can be added to a second power supply and synchronized together. Specification: RGB Controller with Built-In Power Supply No Additional Power Supply Required Input Power: VAC Rear View Output Power: 4 x DC(24V x 4A) 400 Watt Maximum Dimensions: 14.6 x 9.3 x 2.6 in. Weight: 8 lbs Programmable Speed Variations Color Mixing - 16 Million Colors Flash - Fade - Color Wash 17 Built-in Programs - DMX - Master/Slave

2 Lighting Matrix: CONTROLLER POWER RGB PRODUCT CONNECTION 24V 400 Watt DMX Controller 100 Watts 100 RGB Rope 400 Total 33 Starstream 20 Of The Colortube 12 Hard Wire 8 Of The Colortube 39 Accessories: Front power connectors, end caps, mounting clips and leader cables. WDM LIGHTING 2603 OAK LAWN AVE., STE. 120, DALLAS, LAS, TX 75219

3 6 lighting effects modes: There are six lighting effect modes via the RGB controller. 1. Solid Color Mode: Press the mode button until you see a sideways T and numbers (usually 255). This will allow you to adjust the brightness level of the red, blue and green LED s of your fixtures. Press the up or down button to adjust the brightness of red. You have levels of brightness. Press the function button to adjust the brightness of green. Follow the same steps for blue. 2. Colorwash mode: Press the button until you see SP on the LCD screen and a green dot on the roll line. Press the function mode to adjust the flash and speed of the effect. F stands for flash. For no flash effect, keep at to 599 increases the flash effect with 599 at the fastest. Press the function mode again to adjust the speed of the fade effect. When SP is on the screen, press the up button to increase the speed and the down button to decrease the speed. Press the up/down to put the fade effect on red, blue, green or RGB. 3. Color Change Auto mode: Press the button until you see SP on the LCD screen and a green dot on the auto line. Press the function mode to adjust the flash and speed of the effect. F stands for flash. For no flash effect, keep at increases the flash effect with 599 at the fastest. Press the function mode again to adjust the speed of the effect. FD will appear on the screen. The lower the number, the slower the effect.

4 PAGE 03 Mode (continued): 4. Slave Mode: 5. DMX Mode: 6. Sound Mode: Press the mode button until you see the slave effect. This allows the controller to be controlled by another power supply. You must connect a DMX cable in the DMX out of the Master controller to the DMX in of the Slave controller box. Press the mode button to select the DMX mode. Press the function button to select a DMX address or put the DMX running mode into DMX P1 or DMX P2 mode. Press the mode button to select the sound activation effect. SU will appear on the screen with sound sensitivity effects from Press the up/down buttons to raise or lower the sound sensitivity effect. DMX Value Chart

5 PAGE 01 WDM IR REMOTE CONTROLLER Genernal Description: The IR remote together with our LED lights can make colorful and dynamic light scenery effects. It is widely applied to entertainment hall, stage, social club and outdoor building decoration. Key Features: Designed for quick and easy infrared wireless control Black Out Auto Run Button Automatically run through all pre-set programs Select Program Button control access to pre-set programs Flash Button Active strobe function DMX Mode Select different DMX channel modes Sound active button Run programs in sound active mode Slave Mode Control in Master/slave configuration Set Address Set DMX addressing R, G & B Buttons Adjust Red, Green & Blue LED values Number Buttons Use to set DMX values For use up to 30 feet from fixture Dimensions (LxWxH): 4.5 x 2 x.25 / 110 x 46 x 7 mm

6 PAGE 02 WDM IR REMOTE CONTROLLER SPECIFICATION: Battery: 3V fastener battery. Transmitting IR signal available. The distance available is at most 10m or 32 ft. Selectable IR signal including RGB dimming, built-in programs, auto running, flash, speed, slave mode, DMX mode and DMX address for different applications by pushing the buttons which can control the LED lights. OPERATION: 1) BLACK OUT button, set the LED lights power on or power off by pressing this button. 2) A button, set the LED lights in the situation of auto run by pressing this button. 3) PROG button, set the LED lights to run built-in programs by pressing this button; select the programs 7 color selection, color jumping and color dream by pressing + and - buttons. 4) F button, set the LED lights flash on or flash off by pressing this button; increase or decrease the speed of flash by pressing + and - buttons. 5) SP button, set the LED lights running speed by pressing this button. This button is available only in the situation of color jumping and color dream; increase and decrease the speed by pressing + and - buttons. 6) D button, set the LED lights into DMX mode by pressing this button. 7) SA button, set the LED lights into sound activated mode by pressing this button. (unavailable for outdoor LED lights). 8) SL button, set slave mode by pressing this button. 9) S buttons, set DMX address for

7 PAGE 03 WDM IR REMOTE CONTROLLER OPERATION (CONTINUED): The LED lights by pressing these buttons. For example, set DMX address 245 I) Press S button, then the red LEDs are on, it mean you can start to set address. II) Press 2 button, then the green LEDs are on, it means 2 (hundreds place) setting successful. III) Press 4 button, then the blue LEDs are on, it means 4 (tens place) setting successful VI) Press 5 button, then all the R/G/B LEDs are on, it means 5 (ones place) setting and the DMX address setting successful For example, Set DMX address 002 I) Press S button, then the red LEDs are on, it mean you can start to set address. II) Press 0 button, then the green LEDs are on, it means 0 (hundreds place) setting successful.. III) Press 0 button, then the blue LEDs are on, it means 0 (tens place) setting successful.. IV) Press 2 button, then all the R/G/B LEDs are on, it means 2 (ones place) setting and DMX address setting successful.. 10) R G B + and - buttons, set the brightness for the RGB LEDs by pressing these buttons. Notice: The IR remote is not available when the LED lights controlled by DMX controller.