ELAR Tri Brick. Elation Professional 6122 S. Eastern Ave. Los Angeles, Ca Rev. 2/26/2010 visage Version 1.

Transcription

1 ELAR Tri Brick Elation Professional 6122 S. Eastern Ave. Los Angeles, Ca Rev. 2/26/2010 visage Version 1.0

2 Elation Professional, Los Angeles Ca. 1 ELAR Tri Brick

3 TABLE OF CONTENS 1. General Information 3 a. Introduction. 3 b. Unpacking c. Customer Support. 3 d. Warranty Registration Safety Instructions Features 7 4. General Guidelines Fixture Overview Mounting and Installation Understanding DMX a. DMX Cables b. DMX Terminator. 16 c. 3-Pin to 5-Pin Conversion. 17 d. Fixture DMX Addressing Display Indicators Display Menu DMX Addressing. 25 a. Remote DMX Addressing (RDMX) DMX Traits Working with Built-In programs Lens Replacement Cleaning and Maintenance Warranty Photometric Data Dimensional Drawings Circuit Schematic Technical Specifications Elation Professional, Los Angeles Ca. 2

4 1. GENERAL INFORMATION INTRODUCTION: Congratulations, you have just purchased one of the most innovative and reliable LED fixtures on the market today! The ELAR TRI BRICK has been designed to perform reliably for years when the guidelines in this booklet are followed. Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this unit. These instructions contain important information regarding safety during use and maintenance. UNPACKING: Thank you for purchasing the ELAR TRI BRICK by Elation Professional. Every ELAR TRI BRICK has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for damage and be sure all accessories necessary to operate the fixture have arrived intact. In the event damage has been found or parts are missing, please contact our customer support team for further instructions. Inside the box you should find: the fixture, a DMX XLR cable, a safety cable, and this manual. Please do not return this unit to your dealer without first contacting customer support at the number listed below. CUSTOMER SUPPORT: Elation Professional provides a customer support line, to provide set up help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at for any comments or suggestions. For service related issue please contact Elation Professional. Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time. Voice: (323) Fax: (323) support@elationlighting.com Forum: Warning! To prevent the risk of fire and reduce the risk electrical shock, do not attempt to operate this fixture with the lens cover removed. Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs Elation Professional, Los Angeles Ca. 3

5 yourself. Doing so will void your manufactures warranty. Please do not discard the shipping carton in the trash. Please recycle whenever possible. WARRANTY REGISTRATION: The ELAR TRI BRICK carries a two-year (730 days) limited warranty. Please fill out the enclosed warranty card to validate your purchase. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return package. A brief description of the problem as well as the R.A. number must also be written down on a piece of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of your proof of purchase invoice. Items returned without a R.A. number clearly marked on the outside of the package will be refused and returned at customer s expense. You may obtain a R.A. number by contacting customer support at (323) Elation Professional, Los Angeles Ca. 4

6 2. SAFETY INSTRUCTIONS To guarantee proper and consistent operation, it is important to follow the guidelines in this manual. Elation Professional will not accept responsibility for damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. 1. Always be sure that the fan and the air inlets remain clean and are never blocked. Allow about 6 (15cm) between this fixture and other devices or a wall to allow for proper cooling. See page Never touch the fixture during normal operation. 3. Never look directly into the light source. You risk injury to your retina, which may induce blindness. 4. For safe operation, follow the Installation guide described in chapter six of this manual. Operating the ELAR TRI BRICK without suited safety aids such as safety cables or clamps can increase the risk of damage and/or personal injury. 5. Qualified and certified personnel should only perform installation. 6. When mounting this fixture, use only the original rigging points included with this fixture. Any structural modification will void the original manufactures warranty and may increase the risk of damage and/or personal injury. 7. Do not attempt to operate this fixture if the power cord has become damaged or frayed. 8. Never open this fixture while in use. 9. This device falls under protection-class I. Therefore it is essential that the device be grounded properly. 10. Qualified personnel should perform all electrical connections. 11. Be sure the available voltage matches the voltage requirements of the unit. Be sure the power cord is never crimped or damaged. If the power cord is damaged, replace it immediately with a new one of similar power rating. Elation Professional, Los Angeles Ca. 5

7 12. Always disconnect from main power before performing any type of service or any cleaning procedure. 13. Only handle the power cord by the plug. Never pull out the plug by tugging the wire portion of the cord. 14. Please be aware that damages caused by modifications to the device are not subject to warranty. Important Notice: Damages resulting from the disregard of safety and general user instructions found in this user manual are not subject to any warranty claims. Elation Professional, Los Angeles Ca. 6

8 3. FEATURES IP66 Rated Fixture Low power consumption Minimal heat emission Maintenance free operation Equipped with 12 Tri-Color (RGB) 3-Watt LEDs Silent Operation, convection cooled, no fans 100,000 hours rated LED life Linear RGB Color Mixing, infinite color possibilities 18 Beam Angle/35 Field Angle (25 Lens) USITT DMX-512 Complaint Preprogrammed colored macros Strobe-effect with a maximum flash rate of 18fps DMX-controlled operation or stand-alone operation with Master/Slave-function 7 built-in programs can be called up via DMX-controller ~ 48 preprogrammed scenes per program Sound-controlled via built-in microphone Five DMX Modes: 15 DMX Channels 12 DMX Channels 6 DMX Channels 4 DMX Channels 3 DMX Channels (default) DMX-control via standard DMX-controller Upgradable firmware via Elation E-Loader Data Pack Electronic Switching Power Supply 100v~240v Flicker-free operation for television and film Compact design: fits in 12 box truss 0%~100% Dimming (two dimming options; linear & standard) Elation Professional, Los Angeles Ca. 7

9 4. GENERAL GUIDELINES This fixture is a professional lighting effect designed for use on stage, in nightclubs, in theatres, and other types of architectural installations. Do not attempt operation or installation without a proper knowledge on how to do so. Consistent operational breaks will ensure that the fixture will function properly for many years to come. Do not shake the fixture around. Avoid brute force when installing or operating the fixture. While choosing an installation location, please be sure that the fixture will not be exposed to extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat surface should be at least 0.5 meter (about 1.5ft). See page 12. Always install the fixture with an appropriately rated safety cable. When installing the fixture in a suspended environment always be sure to use mounting hardware no less than M10 x 25 mm, also be sure the hardware is only inserted in the yoke s mounting holes. Do not attempt to operate this fixture until you have familiarized yourself with all of its functions. Do not permit operation by persons not qualified for operating this type of architectural fixture. Most damages are the result of improper operation. Please use the original packaging to transport the fixture in for service. For your own safety, please read this user manual carefully before installing the device. Elation Professional, Los Angeles Ca. 8

10 5. FIXTURE OVERVIEW 1. LED Lens Assembly The lens assembly may be user replaced in the event repair is needed or a different beam angle is required. 2. Locking Knob This knob is used to lock the yoke into place after a desired operating angle has been achieved. Elation Professional, Los Angeles Ca. 9

11 3. Yoke Assembly This yoke is designed to perform two functions; 1) It can be used as a floor stand bracket, or 2) Used to secure a mounting clamp for truss mounting. 4. Fixture Housing A heavy-duty aluminum case that is designed to be IP 66 rated. 5. DMX In Lead This lead is the main DMX input lead. When the unit is the first in a chain or the only fixture to be used with a DMX controller, be sure to use the DMX starter cable that converts a standard 3-pin XLR DMX connector to the IP rated twist lock connector that is used on the fixture. When jumping from fixture to fixture be sure to only use Elation IP rated DMX cables to maintain the IP rating. 6. DMX Out Lead This lead is used to send an incoming DMX signal to the next fixture in the DMX chain. To maintain the integrity of the IP rating, only use proper Elation IP rated DMX cables. 7. Main Power Input Lead This lead is the main power input lead. When the unit is the first in a chain or the only fixture to be used, be sure to use the power starter cable that converts a standard Edison 3-prong to the IP rated twist lock connector. When jumping from fixture to fixture be sure to only use Elation IP rated power connectors to maintain the IP rating. 8. Power Output Lead This lead is used to jump power to another ELAR TRI BRICK. Please do not daisy chain power for more than 16 fixtures. To maintain the integrity of the IP rating, only use proper Elation IP rated power cables. 9. MENU Button This button is used to access the fixtures menu functions. 10. Up Button The up button is used to toggle forward through the menu functions and settings. 11. Down Button The down button is used to toggle backwards through the menu Elation Professional, Los Angeles Ca. 10

12 functions and settings. 12. Enter Button The enter button is used to enter in to a certain menu function or to lock a menu setting in to memory. 13. LED Display 4-segment menu display. Used to display the DMX address as well as all other menu functions. Elation Professional, Los Angeles Ca. 11

13 6. MOUNTING AND INSTALLATION Cautions: For added protection mount the fixtures in areas outside walking paths, seating areas, and away from areas were unauthorized personnel might reach the fixture. Before mounting the fixture to any surface, make sure that the installation area can hold a minimum point load of 10 times the device s weight. Fixture installation must always be secured with a secondary safety attachment, such as an appropriate safety cable. To avoid injury, never stand directly below the device when mounting, removing, or servicing the fixture. Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE for proper installation in Europe To ensure proper installation, only qualified staff should attempt installation. Mounting points Overhead mounting requires extensive experience, including amongst others calculating working load limits, a fine knowledge of the installation material being used, and periodic safety inspection of all installation material and the fixture. If you lack these qualifications, do not attempt the installation yourself. Improper installation can result in bodily injury. CAUTION! Be sure a qualified electrician performs all electrical connections. Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet. Elation Professional, Los Angeles Ca. 12

14 Mounting The ELAR TRI BRICK is fully operational in any position, hanging upside-down, side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at least 0.5m (1.5 feet) away from any flammable materials (decoration etc.). When clamp mounting; always use and install the supplied safety cable as an added safety measure to prevent accidental damage in the event of a clamp failure. See the image below. Clamp Mounting The ELAR TRI BRICK provides a mounting bracket assembly that allows the unit to stand on a flat surface or to be hung on truss via a clamp in any safe position (see the illustration above). Regardless of the mounting option you choose please be sure to refer to the safety Elation Professional, Los Angeles Ca. 13

15 guidelines in this manual to avoid damage to the unit and/or personal injury. When mounting this fixture to truss be sure to secure an appropriately rated clamp to the hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an added safety measure be sure to attach at least one properly rated safety cable to the fixture. See illustrations below. Securing the ELAR TRI BRICK Always be sure to secure your fixture with a safety cable when suspending the unit from truss or other means. The fixture provides a built-in rigging point for a safety cable as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to the hanging bracket. Elation Professional, Los Angeles Ca. 14

16 7. UNDERSTANDING DMX DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers. DMX allows all makes and models of different manufactures to be linked together and operate from a single controller. This is possible as long as all the fixtures and the controller are DMX compliant. A DMX controller sends the DMX data instructions to a fixture allowing the user to control the different aspects of an intelligent light. DMX data is sent out as serial data that travels from fixture to fixture via data IN and OUT leads located on the fixtures (most controllers will only have output jacks). DMX Linking: To ensure proper DMX data transmission, always use proper DMX cables and a terminator. When using several DMX fixtures try to use the shortest cable path possible. Never split a DMX line with a Y style connector. The order in which the fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in the DMX chain, at the beginning, at the end, or anywhere in the middle. The DMX controller knows to send data assigned to address 1 to that fixture no matter where it is located in the DMX chain. The ELAR TRI BRICK can be controlled via DMX-512 protocol. The ELAR TRI BRICK is a fixture that can operate in 3, 4, 6, 12 or 15 DMX channels (see pages for the different available DMX settings). The DMX address is set electronically using the controls on the LED menu. Cable Requirements: This fixture is designed with special cables for both DMX and power. These cables are specifically designed to maintain the integrity of the IP rating. When using this fixture outdoors be sure to ONLY use the Elation cables that have been manufactured to meet the IP rating. First DMX Cables - Special DMX First cables may be purchased from Elation to provide a means of data communication with standard DMX fixtures for indoor use. These cables will come with the IP rated twist lock connector on one end and either a 3-pin XLR male or female connector on the other depending on model. Be sure to only use these cables for intergrading this fixture in a standard DMX chain. Elation Professional, Los Angeles Ca. 15

17 First Power Cable A special power First cable is included with every fixture. This cables is used to provide power to your fixture. This cable comes with the IP rated twist lock connector on one end and a standard Edison 3-prong, grounded prong on the other end. Be sure to only use this cable for power distribution and never attempt to connect this cable to the DMX lines. You can chain multiple fixtures together through serial linking. Using the IP rated signal cables provided through Elation. Always be sure to daisy-chain your in and out data connections, never split or Y your DMX connections unless you are using an approved DMX splitter such as the Elation Opto Branch 4 or DMX Branch/4. DMX-512 connection with DMX terminator A DMX terminator should be used in all DMX lines especially in longer runs. The use of a terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the possibilities of erratic behavior. 5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA Elation Professional, Los Angeles Ca. 16

18 transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The following chart details a proper cable conversion. Fixture DMX addressing; All fixtures should be given a DMX starting address when using a DMX controller, so the correct fixture responds to the correct control signal. This digital starting address is the channel number from which the fixture starts to listen to the digital control information sent out from the DMX controller. The allocation of this starting DMX address is achieved by setting the correct DMX address on the digital display located on the back of the fixture. You can set the same starting address for all fixtures or a group of fixtures, or set different address for each individual fixture. Be advised that setting all you fixtures to the same DMX address will subsequently control all fixtures in the same fashion, in other words, changing the settings of one channel will affect all the fixtures simultaneously. If you set each fixture to a different DMX address, each unit will start to listen to the channel number you have set, based on the quantity of control channels (DMX channels) of each fixture. That means changing the settings of one channel will only affect the selected fixture. In the case of the ELAR TRI BRICK, which is up to a 15 channel fixture, you should set the starting DMX address of the first unit to 1, the second unit to 16 (15 + 1), the third unit to 31 Elation Professional, Los Angeles Ca. 17

19 ( ), and so on. Note: During start-up the ELAR TRI BRICK will automatically detect whether a DMX data signal is being received or not. If a DMX data signal is being received, the display will show "A.XXX" (XXX representing the actual DMX address). If the fixture is not receiving a DMX signal the display will flash "A.XXX" (XXX representing the actual DMX address). If your fixture is connected to a DMX controller and the display is flashing (not receiving a DMX signal), please check the following: - The 3-pin or 5-pin XLR plug (cable with DMX signal from controller) may not be connected or is not inserted completely into the DMX input jack. - The DMX controller is switched off or defective. - The DMX cable from the controller merging with included IP Rated Cable adapter is not connected securely - The DMX cable or connector is defective. - A DMX terminator has must be inserted into the last fixture in your DMX chain. Elation Professional, Los Angeles Ca. 18

20 8. DISPLAY LED INDICATOR. The ELAR TRI BRICK has a LED indicator on the display. This indicator is designed to give a quick visual indication of the fixtures DMX status. The illustration below details the functionality of the LED indicators. The LED indicator represents DMX signal: If the indicators is on, a clean DMX signal is present If the indicator is off, there is no DMX signal present Elation Professional, Los Angeles Ca. 19

21 9. DISPLAY MENU Default settings shaded. MODE SET MANL TIME EDIT <ADDR> VALU A001~AXXX (AXXX) DMX address setting SLAV ON/OFF Set as Slave RDMX ON/OFF Change address via DMX <RUN> AUTO ALON/MAST Run Auto program VALU D-XX D-00(DXXX) Display DMX value <DISP> FLIP ON/OFF Flip display D ON ON/OFF Delay shutting off LED display <CHAN> 4CH/5CH/7CH/9CH DMX channel Mode <FAIL> OFF/HOLD/AUTO Status while there is no DMX <DFSE> ON/OFF Default setting <VER> V-1.0~V-9.9 Software version <CH01> ~<CH09> 01 XX (00~FFH) 09 XX (00~FFH) Manual adjust intensity <LIFE> 0000~9999(hours) Life time of machine running <CODE> CXXX Password of clear time 038 <CLFE> ON/OFF Clear machine running time <STEP> S-01~S-48 Select steps of program <SC01> ~<SC48> C-01~C-09 FADE TIME 01 XX (00~FFH) 09 XX (00~FFH) XXX XXX.X (000.1s~999.9s) Edit the internal scenes Remarks: 1) If the fixture does not receive a DMX signal the menu display will flash repeatedly. 2) TIME: Adjust the hold time for each scene in built-in chase programs. 3) FADE: Adjust the fade time between each scene in the built-in programs. 9.1 MODE - Function Mode: <ADDR> - DMX address setting This function is used to set or adjust the fixture s starting DMX address. Every device controlled by DMX has to have a unique starting address. The addressing feature is what allows DMX to function properly. The DMX address of a fixture is what allows it to communicate with a controller properly. The DMX addressing also allows the fixture to ignore any DMX information coming from the controller that is not meant specifically for the fixture. Because each fixture is connected Elation Professional, Los Angeles Ca. 20

22 in a daisy-chain fashion it is imperative to assign a proper and unique starting DMX address to each and every fixture. The DMX address is non-destructive and will remain in the fixture s memory even when the power to the unit is switched off. Memory is backed-up and retain by an internal power source that should last about five years. For proper DMX addressing see DMX Addressing on page 25 of this user manual. VALU - Display the DMX 512 value of each channel With this function you can display the DMX 512 value of each channel. The display will automatically detail the changing DMX values as they are received from the controller. SLAV - Slave setting for Master/Slave Operation With this function, you can define the device as slave for operation in Master/Slave mode. Each slave setting will have a different function for a dynamic lightshow without a controller. RDMX - Address via DMX - This function allows the DMX address to remotely be adjusted from a DMX console. This setting requires special settings for both the controller and the fixture. RDMX is on by default. For operational instructions please see Section 10/Page 25 of this manual Remote DMX addressing <RUN> - Internal Program Settings This function allows the internal programs to run in either stand-alone or master/salve mode. In Master mode the fixture will send DMX data to other fixtures connect via the DMX chain. In Alone mode the fixture will operate as a single fixture. The program for this mode is selected in the Select program section of the control menu. You can set the number of steps under Edit program. You can edit the individual scenes under Edit scenes. With this function, you can run the individual scenes either automatically, i.e. with the adjusted Step-Time. Elation Professional, Los Angeles Ca. 21

23 9.1.3 <DISP> - Menu Display Settings This function allows the internal programs to run in either stand-alone or master/salve DMX chain. In Alone mode VALU - Display the DMX 512 value of each channel This function will electronically display the current DMX value for any channel that is currently being adjusted. The display will automatically detail the changing DMX values as they are received from the controller. This function is off by default. FLIP This function will flip the display readout by a 180 allowing for better visualization when the fixture is mounted in an inverted position. D ON The display is designed to turn off during normal operation to avoid excessive light in situations that require an extremely dark environment. This function will adjust the time delay the fixture will remain on before it turns off. This function is disabled as default. 9.2 SET Fixture Personality Settings: These functions set specific running modes and operating parameters. <CHAN> DMX Mode settings This function allows the fixture to run in different DMX channel modes. The five modes are available; 3 channel, 4 channel, 6 channel, 12 channel and 15 channel. See DMX Traits beginning on page 27 for a detailed explanation of the different DMX modes. <FAIL> DMX Fault Protection This function dictates how the fixture will operate in the event DMX signal is suddenly lost while operating in DMX mode. The three fail safe modes are; 1) OFF which will blackout all light output. 2) HOLD, which will hold the last DMX command, or 3 AUTO, which will put the fixture in sound-active mode. Elation Professional, Los Angeles Ca. 22

24 <DFSE> - Restore Default This function is used to restore the factory settings of the device. All settings will be set back to the default values (shaded). Any edited scenes will be lost. <VER> Software Version This function will display the current firmware version. 9.3 MANL Manual Fixture Settings: This function allows the each of the nine DMX channels to be controlled manually. This will allow the fixture to be preset to a specific color or built-in program without the use of a DMX console. 9.4 TIME Operating Hours These functions will detail different time functions associated with the fixture. <LIFE> (0000~9999 Hours) This function tracks the running time of the fixture from the point it was last cleared. Where XXXX represents the total number of running hours. This time is none destructive and will remain in the fixtures memory indefinitely. Use this time to track rentals or show durations. <CODE> Clear run time access code This lock-out code prevents the current run time from being erased accidently. The access code is 038 <CLFE> Clear Fixture Run Time This function resets the run time to zero. 9.5 Edit Internal Program Settings: The fixture comes equipped with a built-in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board. Programs can be created and stored using the fixture s control board or by using an external DMX Elation Professional, Los Angeles Ca. 23

25 controller. For detailed instructions on how to complete this task please see Working with Built-In Programs Section 12/ Page Select program This function allows the user to select one of ten of the user defined built-in programs. This program is then accessed in Function Mode under Program Run Edit program This function allows the user to edit the built-in programs Edit Scenes This function allows the user to edit or define the actual scenes that are stored in the user defined built-in programs that are accessed in the previous step. Elation Professional, Los Angeles Ca. 24

26 10. DMX ADDRESSING Setting the DMX address - After the fixture is turned ON it will immediately complete a reset process that test all the fixture s functions. When the reset process concludes the LCD will display the fixture s current DMX address. If the fixture is not receiving a DMX signal, the display will flash continuously. To set or adjust a DMX address, please follow the procedure below: 1. Toggle through the menu by pressing the Up and Down buttons until the display reads Addr=XXX. Tap the enter button to make changes to the address. 2. While the display is flashing use the UP and DOWN buttons to select a new address. Once the new address has been selected, lock the new address into the fixture s memory by pressing the ENTER button. The DMX address is non-volatile and will remain in the fixture s memory even when the power to the unit is switched off. Memory is backed-up and retain by an internal power source that should last about five years Remote DMX addressing (RDMX) / Address Via DMX- This function allows the DMX address to be changed remotely from a DMX console. This setting requires special settings for both the controller and the fixture. This function may be turned on and off, and is ON be default. Follow the procedure listed below to access the RDMX functions: Fixture Settings: 1. Access the main menu and use the UP or DOWN to get to the Personality menu, then press ENTER 2. Once in the Personalities menu, tap the UP or Down to get to the Status Settings menu, press ENTER. 3. Once in the Status Settings tap the UP or Down to get to the Address via DMX function and press ENTER. 4. Address via DMX is the function that turn the RDMX function on and off. Press ENTER and be sure the function is turned on. 5. Press the UP button to display ON to activate this function, or OFF to deactivate this function. Elation Professional, Los Angeles Ca. 25

27 6. Press ENTER to confirm. 7. Press MODE/ESC to return to the main menu. Controller Settings: 1. Set the DMX value of channel 1 to a value of Set the DMX value of channel 2 to a value of 7 or 8. When channel 2 is set to "7" you can adjust the starting address between 1 and 255. When set to "8" you can adjust the starting address between 256 and Use channel 3 to set your desired DMX starting address. For example: If you want to set the starting address to 57, set channel 1 to a value of 7, set channel 2 to a value of 7 and use channel 3 to set your address to 57 by selecting a channel value of 57. Example 2: If you want to set the starting address to 420, set channel 1 to a value of 7, channel 2 to "8" and channel 3 to "164" ( =420). 4. Wait for approximately 20 seconds for the unit to complete the address reset function. Elation Professional, Los Angeles Ca. 26

28 11. DMX TRAITS DMX Operation Notes: The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please note that this will override all manual settings. This unit will keep and retain the last DMX command in the event of DMX signal failure. To reset the fixture you must turn the power off. DMX CHANNEL TRAITS The charts below and on the preceding pages outline the different DMX traits for the three different DMX modes. 3-Channel mode: In this mode channel one controls all the red LEDs, channel two controls all the green LEDs, and channel three controls all the blue LEDs. Elation Professional, Los Angeles Ca. 27

29 4-Channel mode: In this mode channel one controls all the red LEDs, channel two controls all the green LEDs, channel three controls all the blue LEDs, and channel four controls the master dimming level. 6-Channel mode: In this mode channels 1~3 are used to control the RGB LEDs and channels 4~7 will control special features. Elation Professional, Los Angeles Ca. 28

30 12-Channel mode: In this mode channels each color is controlled individually. ELAR Tri Brick 15-Channel mode: In this mode channels each color is controlled individually using channels 1-12 and channels are used to control special features. Elation Professional, Los Angeles Ca. 29

31 DMX channel functions and their values: Mode/Channel Value Function 3CH 4CH 6CH 12CH 15CH Red (0-Black, %) Green (0-Black, %) Blue (0-Black, %) 0-10 No function Internal program Internal program Internal program Internal program Internal program Internal program Internal program Internal program Red (group1) Green (group1) Blue (group1) Red (group2) Green (group2) Blue (group2) Red (group3) Green (group3) Blue (group3) Red (group4) Green (group4) Blue (group4) 0 No function (shutter open) 1-95 Strobe effect slow to fast No function (shutter open) Pulse-effect in sequences No function (shutter open) Random strobe effect slow to fast No function (shutter open) Dimming (0-Black, %) Elation Professional, Los Angeles Ca. 30

32 12. WORKING WITH BUILT-IN PROGRAMS The fixture comes equipped with a built-in DMX recorder that allows custom programs to be installed and recalled directly from the fixture s control board. Programs can be created and stored using the fixture s control board or by using an external DMX controller. The following instructions will detail the procedures for using the on-board system menu as well as using a DMX compliant controller. Memory Statistics: Quick Access Programs (Program Part): 3 Total Number of Programs: 10 Maximum Number of Steps (Scenes) per a Program: 64 Total Number of Scenes (Steps): 250 Step 1 Building Scenes. The control will store a maximum of 250 scenes. These scenes are then used to create the programs. A program can store one or a maximum of 64 scenes. Keep in mind that a scene can only be access when it is stored in a Program. If you wish to build a static scene (a scene consisting of no movement) for a logo or gobo projection, the scene must be stored inside a program. To build a scene, follow the instructions below: Access the main menu and toggle to Edit Programs which is menu function 5. Then tap the ENTER button and toggle to Edit Scenes, menu function 5-3. When you get to the Edit Scenes function tap the ENTER button. The screen will then change to Edit Scene 001, this will be menu function You can then press the ENTER button to begin to edit scene 1 or use the UP and DOWN buttons to toggle to access scenes Once in the scene edit screen you have access to the functions listed below. Tapping the ENTER button will instantly allow you to change the values of the selected function in real time. The values can be adjusted from 0~250. Once you achieved your desired value tap the ENTER button once again to automatically Elation Professional, Los Angeles Ca. 31

33 lock the value into the scenes memory. You can repeat the procedure for all functions listed below: - Auto Program Allows access to all of the fixture s DMX traits. - Red adjust all of the red LED values - Green adjust all of the green LED values - Blue adjust all of the blue LED values - Strobe adjust the strobe - Dimmer adjust the dimmer intensity - Scene Time set the hold time for the scene - Input By Out this function will store a scene from an external DMX console. See the next section for scene editing via an external DMX controller. Step 1B Building Scenes from an External DMX Controller The fixture includes a simple built-in DMX recorder. This recorder allows you to build a scene using your own DMX console. That scene can then be sent to the fixture and be stored inside one of the fixture s scene storage banks. Many people may find this procedure easier and quicker than using the on board menu functions as in Step 1. To store a scene from an external DMX controller follow the procedures below: - Using your DMX control build and store scenes as you normally would. - Once you have built all your required scenes, enter the fixtures main menu and toggle to Step 2 Editing Programs. The control will store a maximum of 10 programs. A program can store one or a maximum of 64 scenes. Keep in mind that a scene can only be access when it is stored inside one of the 10 available programs. Follow the procedure below to build an internal program: Access the main menu and toggle to Edit Programs which is menu function 5. Then tap the ENTER button and toggle to Program 1 menu function When you get to the Program 1 function tap the ENTER button. The screen will then change to Edit Steps 01, this will be menu function Use the UP and DOWN buttons to toggle through the scenes created in Step 1. Press the Elation Professional, Los Angeles Ca. 32

34 ENTER button to add a scene to the program. Tapping the Enter button will automatically lock the selected scene into the programs memory. Repeat the process until all the desired scenes have been added to the program. Each program can store a maximum of 64 scenes. To test the program access Program Test in the Program Edit menu function. Step 3 Playing a Program To initiate a program follow the procedure below: Access the main menu and use the Up and Down to toggle to Function Mode and tap the Enter button. In the next screen select Auto Program and tap the Enter button. There are now two selections, Master and Alone. Select Master when running multiple fixtures in a master/slave configuration. See section 10.2 Master/ Slave Operation on page 25 for proper set-up instructions. Select Alone when running a single fixture or when multiple fixtures in stand-alone mode. See section 10.1 Stand-Alone Operation on page 25 for proper set-up instructions. The 3 Slave groups run the Auto Program in certain time segments, as shown in the following diagram: Elation Professional, Los Angeles Ca. 33

35 13. LENS REPLACEMENT The ELAR TRI BRICK comes with a removable front cover that allows the lens assembly to be changed out to achieve different beam angles. Lens cover is held in place by 4 screws on the back of the lens assembly. To remove the cover; 1) Remove the securing fasteners in a counter-clockwise direction. 2) Once the fasteners are removed, lift the cover straight up to expose the inner lens (see illustration below). 3) Locate the securing screws on the inner cover and remove them. 4) Remove the inner cover to access the four individual lens kits (see illustration below). Once the lenses are changed reassemble in reverse order. Elation Professional, Los Angeles Ca. 34

36 14. CLEANING AND MAINTENANCE Consider the following points during normal service and inspection: 1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may fall out during normal operation resulting in damage or injury as larger parts could fall. 2. Electric power supply cables must not show any damage, material fatigue or sediments. Never remove the ground prong from the power cable. Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed. We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or solvents. There are no user serviceable parts inside this fixture, please refer all other service issues to an authorized Elation service technician. Should you need any spare parts, please order genuine parts from your local dealer. Elation Professional, Los Angeles Ca. 35

37 15. 2-YEAR LIMITED WARRANTY A. Elation Professional hereby warrants, to the original purchaser, Elation Professional products to be free of manufacturing defects in material and workmanship for a period of two years, (730 days) from the date of purchase. This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought. B. For warranty service, send the product only to the Elation Professional factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty, Elation Professional will pay return shipping charges only to a designated point within the United States. If the entire instrument is sent, it must be shipped in its original package. No accessories should be shipped with the product. If any accessories are shipped with the product, Elation Professional shall have no liability what so ever for loss of or damage to any such accessories, nor for the safe return thereof. C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which Elation Professional concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the Elation Professional factory unless prior written authorization was issued to purchaser by Elation Professional ; if the product is damaged because not properly maintained as set forth in the instruction manual. D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, Elation Professional will replace defective parts at its expense, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of Elation Professional under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of Elation Professional. All products covered by this warranty were manufactured after January 1, 1990, and bare identifying marks to that Elation Professional, Los Angeles Ca. 36

38 effect. E. Elation Professional reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by Elation Professional in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation Professional be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product. G. This warranty is the only written warranty applicable to Elation Professional Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published. Elation Professional, Los Angeles Ca. 37

39 16. PHOTOMETRIC DATA Elation Professional, Los Angeles Ca. 38

40 17. DIMENSIONAL DRAWINGS Elation Professional, Los Angeles Ca. 39

41 18. CIRCUIT SCHEMATIC Elation Professional, Los Angeles Ca. 40

42 19. TECHNICAL SPECIFICATIONS Power supply: 100v~240v / 50Hz~60Hz AC Power consumption: Maximum 120w LED Configuration: 12 x 3 Watt Tri Color (RGB) LEDs IP Rating: IP66 Weight: 6 Kgs / 15.2Lbs DMX Channel Modes: 15, 12, 9, 4, or 3 (default) Channel mode DMX Drive: Standard DMX-512, 3 pole IP Rated Locking Connector; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1. Color Mixing: RGB Color Additive Mixing Beam Angle: 18 Beam Angle/35 Field Angle (25 Lens) Fuse: GMA 220v~2A (Internal) Dimmer: Continuous Dimming 0~100% Strobe: Electronic Strobe 0~18 Fps Lamp Life: 100,000 Hours Rated Life Dimensions: (232 x 220 x 260) mm 9.13 x Please Note: Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice. Elation Professional, Los Angeles Ca. 41

43 Elation Professional, Los Angeles Ca ELAR Tri Brick

44 Elation Professional 6122 S. Eastern Ave. Los Angeles, CA / fax / Info@ElationLighitng.com Rev. 2/26/2010 visage Version 1.0