CMX-12. HD/SD Digital AV Mixer OPERATIONS MANUAL

Transcription

1 HD/SD Digital V Mixer OPERTIS MNUL

2 DISCLIMERS The information in this manual has been carefully checked and is believed to be accurate. CYP (UK) Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. CYP (UK) Ltd assumes no responsibility for any inaccuracies that may be contained in this document. CYP (UK) Ltd also makes no commitment to update or to keep current the information contained in this document. CYP (UK) Ltd reserves the right to make improvements to this document and/or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise without express written permission and consent from CYP (UK) Ltd. Copyright 2011 by CYP (UK) Ltd. ll Rights Reserved. Version 1.1 ugust 2011 TRDEMRK CKNOWLEDGMENTS ll products or service names mentioned in this document may be trademarks of the companies with which they are associated. 3

3 SFETY PRECUTIS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: lways follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. Never spill liquid of any kind on or into this product. Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. REVISI HISTORY VERSI NO. DTE SUMMRY OF CHNGE RDV1 15/02/2012 Preliminary Release 4

4 CTENTS 1. Introduction pplications Package Contents System Requirements Features Operation Controls and Functions Position/Time Wipe Modes Mode Control Digital Effects djust Video Source Select udio/video Mixer udio Level Rear Panel Operation asic Operation Input Signal Selection and ack Color Selection Video Mix Video Wipe PTTERN Selection Multiple Pattern Selection E-WY REVERSE Picture-In-Picture UTO FDE/ Selection DIGITL EFFECT UDIO ER OSD DJUST Connector and Installation Front Panel Connections Rear Panel Connections Output Resolutions Specifications

5 1. INTRODUCTI The is a high-quality Standard and High Defintion Digital udio/video Mixer. Each input US supports up to 6 inputs (2 HDMI, 2 Component (SD/HD), 2 S-Video and Composite video). Effects can be added such as wipes, fades, mixes and speacial digital effects. The can support HD or SD resolutions (480p, 576p, 720p 50/60, 1080i 50/60), most of the worlds video standards (NTSC, NTSC-4.43, PL, PL-M, PN-N, SECM) and HDMI, Component, S-Video or Composite video outputs, it also supports position adjustment and recording. The output resolution can automatically adjust to input resolution or be manually adjusted (please refer to the diagram above). 2. PPLICTIS matuer/professional Video and udio Mixing. 3. PCKGE CTENTS SD/HD Video and udio Mixer. Cable Pack: 1 HDMI Cable/1 S-Video Cable/1 Stereo udio and Composite Video Cable/1 Stereo udio to 3.5 mm Jack cable/1 Component (YPbPr) Cable. 1 Metal Joystick (screw attchment) for Position control. 12 V/5.0 DC power adaptor. User Manual. 4. SYSTEM REQUIREMENTS HDMI (Non-HDCP), HD (YPbPr) or SD (Composite or S-Video) Source. HDMI (Non-HDCP), HD (YPbPr) or SD (Composite or S-Video) Recording Device. HDMI (Non-HDCP), HD (YPbPr) or SD (Composite or S-Video) Monitor or display. 5. FETURES Selective size and position for digital effects area and windows. utomatic fade and wipe with speed preset control. Digital effects- Still,Mosaic,Paint and Negative. 96 wipe patterns. Chroma key & Luminance key. High Picture Quality. 3 8 back color. Joystick control for digital effect position. Fade control for Video and udio. Video and udio mixing. 2 HDMI source inputs. 2 Component (YPbPr) source inputs. 2 Composite and S-Video source inputs. 1 HDMI recording output. 2 Component (YPbPr) recording outputs. 1 Composite and S-Video recording outputs. 1 Composite and S-Video preview outputs with On-screen Display. uxiliary audio input. Microphone input and headphone output. Picture in Picture control (3 window sizes). Each / US can adjust the Contrast/rightness/Color/Hue/Detail and spect Ratio. Supports Lip-Sync delay up to 170 ms. Composite supports 3D comb filter and YC separation. Motion and Edge daptive De-interlacing. Note: When receiving content that has HDCP encryption there will be no video output same as for HDMI output port. 6

6 6. OPERTI CTROLS ND FUNCTIS 6.1 Position/Time TIME ➊ TIME EFFECTS ER FUNCTIS E-WY REVERSE MODE CTROL L D UDIO LEVEL R D DIGITL EFFECTS DJUST DJUST 1 DEMO POSITI STILL PINT NEGTIVE MOSIC POSITI ➋ SOURCE SOURCE L- - SOURCE SELECT /UDIO ER INPUT INPUT UX MIC SCN UDIO FOLLOW HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / STRT ➊ Time Control For adjusting the transition time of the uto Fade and the uto Wipe functions. ➋ Joystick control The joystick control has two functions, it controls the position of the 'Shape' wipe pattern (button ⓫) and the on-screen location of the picture-in-picture box (button ⓭). 7

7 6.2 Wipe Modes O EFFECTS ER FUNCTIS UDIO L D E-WY REVERSE LEVEL R D ➌ ➍ ➎ TIME EFFECTS ER FUNCTIS E-WY REVERSE MODE CTROL DIGITL EFFECTS DJUST DJUST X DEMO ➏ ➐ ➑ POSITI SOURCE SOURCE STILL PINT NEGTIVE MOSIC SCN SOURCE SOURCE L- - SOURCE SELECT /UDIO ER INPUT INPUT UX MIC ➒ ➓ ⓫ UDIO FOLLOW L- - HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / STRT ➌ One-way wipe button Selects the standard direction for the wipe pattern. ➍ Reverse wipe button Selects the reverse direction for the wipe pattern. ➎ Multiple wipe button dds multiple wipes to the wipe pattern (up to 4 wipes). ➏ Straight wipe button Selects and toggles between 4 straight vertical or horizontal wipe patterns. ➐ Split wipe button Selects and toggles between 4 split wipe patterns. ➑ Corner wipe button Selects and toggles between 4 wipe patterns that originate from a corner. ➒ Diagonal wipe button Selects and toggles between diagonal style wipe patterns. ➓ Triangle wipe button Selects and toggles between triangle style wipe patterns. ⓫ 'Shape' wipe button Selects and toggles between 4 differently 'shaped' wipes patterns (circle, oval, diamond and square). The position of the wipe can be adjusted using the Position Joystick (➋) 8

8 6.3 Mode Control MODE CTROL UDIO L D LEVEL R D ⓬ ⓭ TIME EFFECTS ER FUNCTIS E-WY REVERSE MODE CTROL DIGITL EFFECTS DJUST DJUST 4 DEMO ⓮ ⓯ POSITI SOURCE SOURCE STILL PINT NEGTIVE MOSIC SCN L- - SOURCE SELECT /UDIO ER INPUT INPUT UX MIC ⓯ ⓰ UDIO FOLLOW HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK VIDE UTO / STRT ⓫ Wipe button Selects the wipe mode. ⓬ button Selects the picture-in-picture mode. ⓭ Mix (Fade) button Selects the fade in/out mode. ⓮ button Selects the blue key and luma key effects mode. ⓯ button In wipe mode, toggles between sharp/soft or colored edge. ⓰ button Toggles the edge colour when the button is set to coloured edge mode. 9

9 6.4 Digital Effects UDIO L D DIGITL EFFECTS LEVEL R D EFFECTS ER ⓲ ⓳ ⓴ TIME FUNCTIS E-WY REVERSE MODE CTROL DIGITL EFFECTS DJUST DJUST DEMO POSITI STILL PINT NEGTIVE MOSIC SOURCE SOURCE SCN STILL PINT NEGTIVE MOSIC L- - SOURCE SELECT /UDIO ER INPUT INPUT UX MIC UDIO FOLLOW HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / STRT ⓲ -bus digital effect button. ⓳ -bus Still button/osd left adjust. ⓴ -bus Paint button/osd right adjust. -bus Negative button/osd up adjust. -bus Mosaic button/osd down adjust. -bus digital effect button. -bus Still button. -bus Paint button. -bus Negative button. -bus Mosaic button. 10

10 6.5 djust DJUST DJUST EFFECTS ER L D UDIO LEVEL R D TIME FUNCTIS MODE CTROL DIGITL EFFECTS DJUST E-WY REVERSE DJUST DEMO POSITI SOURCE SOURCE STILL PINT NEGTIVE MOSIC DEMO MOSIC SCN L- - SCN SOURCE SELECT /UDIO ER UDIO FOLLOW INPUT INPUT UX MIC HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / STRT DJUST button When activated, the Setup Menu is displayed through the SD Preview output. In this mode, the menu can be navigated and values adjusted using the cursor buttons (⓳ t ⓴ u and p ). When deactivated the SD Preview output will show -bus/-bus output source and format. DEMO button When pressed, this button places the unit into DEMO mode and will cycle through all 96 wipe patterns. The speed of the DEMO mode can be controlled with the Time Control (➊). Press the DEMO button again to cancel DEMO mode. SCN button If the SCN button is pressed for 3 seconds, the system will enter SCN mode and will SCN the input ports from 1 to 6 and record each port's format to the system memory. 11

11 6.6 Video Source Select L UDIO LEVEL R D D EFFECTS ER TIME FUNCTIS MODE CTROL DIGITL EFFECTS DJUST E-WY REVERSE DJUST DEMO SOURCE SELECT POSITI SOURCE SOURCE STILL PINT NEGTIVE MOSIC SCN L- - SOURCE SELECT /UDIO ER INPUT INPUT UX MIC UDIO FOLLOW HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK STRT / Selects Source 1, HDM I 1 for -bus/-bus. / Selects Source 2, for -bus/-bus. / Selects Source 3, HD input 1 for -bus/-bus. / Selects Source 4, HD input 2 for -bus/-bus. / Selects Source 5, SD input 1 for -bus/-bus. When both S-Video and Composite Video sources are connected at the same time, S-Video will be the first source to be displayed. / Selects Source 5, SD input 2 for -bus/-bus. When both S-Video and Composite Video sources are connected at the same time, S-Video will be the first source to be displayed. Selects the -bus background color, one of eight colors can be selected. Selects the -bus background color, one of eight colors can be selected. 12

12 6.7 udio/video Mixer L UDIO LEVEL R D D EFFECTS ER TIME FUNCTIS MODE CTROL DIGITL EFFECTS DJUST E-WY REVERSE DJUST POSITI SOURCE SOURCE STILL PINT NEGTIVE MOSIC DEMO /UDIO ER INPUT INPUT UX MIC SCN L- - UDIO FOLLOW SOURCE SELECT /UDIO ER UDIO FOLLOW INPUT INPUT UX MIC HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / STRT UTO / STRT -bus LED indicator/ -bus LED indicator. Indicates which input signal is currently in use and displayed. When the Video Slider is at the top, -bus input signal is selected/displayed and the -bus indicator is lit. When the Video Slider is at the bottom, the -bus input signal is selected/displayed and the -bus indicator is lit. When the Video Slider is at anypoint between, the two LEDs will flash in squence to indicate that wipe/fade/mix is in progress. slider Controls the Wipe, and Key effects. Move the slider to control the position of a wipe, the degree of fade or mix, or the strength of a Luma key or blue key effect. UDIO FOLLOW Controls manual or automatic audio mixing. When activated the audio mix between -bus and -bus audio inputs is controlled by the Video Slider (). When deactivated, the audio mix between the -bus and -bus can be independently controlled and. Note: UDIO FOLLOW only affects the Input or Input audio mix, the UX or MIC inputs remain unaffected. UTO/ When pressed, puts the unit into UTO/ mode and disables the Video Slider. STRT button When the start button is pressed, the most recently programmed wipe/fade/mix is initiated. The TIME control (➊) can be used to adjust the length of the transition. The LED will be lit for the duration of the transition and will go out when complete. INPUT Controls the audio level of Input. INPUT Controls the audio level of Input. UX Controls the audio level of the uxiliary input. MIC Controls the audio level of the Microphone input. 13

13 6.8 udio Level L UDIO LEVEL R D D TIME POSITI EFFECTS ER FUNCTIS E-WY REVERSE MODE CTROL DIGITL EFFECTS STILL DJUST DJUST DEMO PINT NEGTIVE MOSIC L UDIO LEVEL R D D SOURCE SOURCE SCN L- - SOURCE SELECT /UDIO ER INPUT INPUT UX MIC UDIO FOLLOW HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / STRT udio level indicator (udio level) This indicator shows the audio output level of REC out 1 and REC out 2. 14

14 6.9 Rear Panel HD UDIO INPUT SD UDIO INPUT UX INPUT UDIO OUTPUT R1 L1 R2 L2 R1 L1 R2 L2 RR LL 1 1L R2 2 Y HD INPUT 1 Pb Pr SD INPUT 1 VS HD OUTPUT 1 Y Pb Pr SD PREVIEW VS HDMI INPUT HDMI OUTPUT DC INPUT 12V Y Pb HD INPUT 2 Pr VS SD INPUT 2 Y Pb HD OUTPUT 2 Pr VS SD OUTPUT Source 3 HD audio input 1. Source 4 HD audio input 2. Source 5 SD audio input 1. Source 6 SD audio input 2. uxiliary udio input Jack. Recording out 1 udio output Jack. Recording out 2 udio output Jack. Power Switch Source 1 HDMI input 1. Source 2 HDMI input 2. Source 3 HD Y-P-PR Video input 1. Source 4 HD Y-P-PR Video input 2. Source 5 SD Video and YC input 1. Source 6 SD Video and YC input 2. HDMI output for monitor. Recording out 1 HD YPb-Pr Video output jack. Recording out 2 HD YPb-Pr Video output jack. SD PREVIEW out (OSD) Video and YC output jack. SD Recording out Video and YC output jack. DC INPUT 12V

15 7. OPERTI 7.1 asic Operation Turn the power switch at the rear panel to the Position. The LEDs on the operation panel will light up and the unit is now in inital mode for operation. 7.2 Input Signal Selection and ack Color Selection SOURCE SELECT /UDIO ER UDIO FOLLOW 2 3 HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK UTO / 4 1 STRT qmove the Video slider (utton ) to the -bus position. The -bus LED will turn on, -bus LED will turn off. wselect your source for -bus from any of the Sources (,, HD Input 1, HD Input 2, SD Input 1 or SD Input 2) and ack color button. You will see the corresponding picture on the screen. 3Press a ack Color button to select the background color required. Repeatedly pressing the ack Color selection button will cycle through the available background colors (lue, Red, Magenta, Green, Cyan, Yellow, White or lack). 4The same procedures apply to the -bus. NOTE: When the selected source input is not connected or has HDCP protection, only a blank, blue screen will be displayed. 16

16 7.3 Video Mix MODE CTROL SOURCE SELECT /UDIO ER 1 2 HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK 3 4 Reset the operation panel to initial mode: qpress the button to put the unit into mix mode 2Press one of the -bus selection buttons to select a source. epress one of the -bus selection buttons to select a source. rthe Mix effect can be controlled by the Video slider by moving it from to or to. 7.4 Video Wipe EFFECTS ER MODE CTROL SOURCE SELECT /UDIO ER E-WY REVERSE DJUST SOURCE SOURCE 1 w STILL PINT NEGTIVE MOSIC HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 DEMO CKSCN L- - t 6 3 r Reset the operation panel to initial mode: qpress the button ⓬. 2Press one of the -bus selection buttons to select a source. epress one of the -bus selection buttons to select a source. rthe effect can be controlled by the Video Slider by moving it from to or to, horizontally or vertically depending on the type of wipe used. tpress button ⓰ to select sharp/soft/colored wipe edge. ywhen the colored edge option for the wipe is selected, press button ⓱ to select one of the eight colors available. 17

17 7.5 PTTERN Selection FUNCTIS E-WY REVERSE SOURCE 4 L- 5 SOURCE 6 - rpress the triangle wipe button ➒ repeatedly to toggle through the available wipe patterns. Four are available: Left to right, ottom to top, top and bottom simultaneously and left and right simultaneously. There are Six wipe modes available can be selected as follows: q Press the straight wipe button ➏ repeatedly to toggle through the available wipe patterns. Four are available: Left to right, right to left, top to bottom and bottom to top 5Press the split wipe button ➓ repeatedly to toggle through the available wipe patterns. Four are available: Left and right simultaneously, top and bottom simultaneously, all four corners simultaneously and rectangles from left and right simultaneously. 2Press the corner wipe button ➐ repeatedly to toggle through the available wipe patterns. Four are available: Top right to bottom left, bottom right to top left, bottom left to top right and top left to bottom right. 6Press the 'Shape' wipe button ⓫ repeatedly to toggle through the available wipe patterns. Four are available: Circle, oval, diamond and rectangle. The position of each wipe pattern in this section can be set via the Joystick Control ➋. 3Press the diagonal wipe button ➑ repeatedly to toggle through the available wipe patterns. Four are available: Top right to bottom left, bottom right to top left, bottom left to top right and top right to bottom left. 18

18 7.6 Multiple Pattern Selection FUNCTIS MODE CTROL SOURCE SELECT /UDIO ER E-WY REVERSE SOURCE SOURCE 4 HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK L Press the button ⓬ to place the unit in mode. 2 Select a wipe pattern e.g. straight wipe by pressing button ➏. 3 Press the button ➎ repeatedly to have the desired multiplication effect. Four options are available: x1, x2, x4 and x8 4 Press one of the -bus selection buttons to select a source. 5 Press one of the -bus selection buttons to select a source. 6 Use the Video Slider to control the wipe pattern. *The same procedure applies to the other wipe patterns. 7.7 E-WY 1 Press the button ⓬ to place the unit in mode. 2 Select a wipe pattern e.g. straight wipe by pressing button ➏. 3 Press the E-WY ➌ button. 4 Press one of the -bus selection buttons to select a source. 5 Press one of the -bus selection buttons to select a source. 6 Use the Video Slider to control the wipe pattern. bus bus *The wipe pattern moves in the normal direction the Video Slider control is operated. 7.8 REVERSE 1Press the button ⓬ to place the unit in mode. 2Select a wipe pattern e.g. straight wipe by pressing button ➏. 3Press the REVERSE ➍ button. 4Press one of the -bus selection buttons to select a source. bus bus *The direction of the wipe pattern is reversed when the Video Slider control is operated. 5Press one of the -bus selection buttons to select a source. 6Use the Video Slider to control the wipe pattern. 19

19 7.7 Picture-In-Picture MODE CTROL FUNCTIS SOURCE SELECT /UDIO ER r ⓭ 5 E-WY REVERSE ➏ ➐ ➑ SOURCE SOURCE ➒ ➓ ⓫ 2 HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 CK L Press the operation panel to initial mode: qmove the Video Slider fully to the -bus position. 2Press one of the -bus selection buttons to select a source. 3Press one of the -bus selection buttons to select a source. 4Press the button to put the unit into picture-in-picture mode. 5The mode can be selected by pressing ➏ ~ ⓫ buttons: ➏ Shows the picture-in-picture box at 1 2 size without the frame edge. ➐ Shows the picture-in-picture box at 1 3 size without the frame edge. ➑ Shows the picture-in-picture box at 1 4 size without the frame edge. ➒ Shows the picture-in-picture box at 1 2 size with the frame edge. ➓ Shows the picture-in-picture box at 1 3 size with the frame edge. ⓫ Shows the picture-in-picture box at 1 4 size with the frame edge. NOTE: The color of the frame edge can be changed by using the back color select button. When you move the Video Slider to the -bus position picture dissolves into background scene. The position of the frame can be controlled by the Joystick Control ➋. bus bus bus bus No edge Edge 20

20 7.8 MODE CTROL FUNCTIS SOURCE SELECT /UDIO ER E-WY REVERSE q ⓭ r y SOURCE L- SOURCE - ➏ ➐ ➑ ➒ ➓ ⓫ Reset the operation panel to initial mode: How to use the LUM effect: 2 qpress the button ⓯ to place the unit in TIME mode. 2Press one of the -bus selection buttons to select a source. 3Press one of the -bus selection buttons to select a source. 3 HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 rpress the LUM button ➒. The darker areas of the picture will become transparent and allow the image of the other source to show through. POSITI 5Use the Video Slider to control the Luma key level. 6Press button ➏ or ➐ to change the source that is being keyed. 7Press the LUM ➒ again to reverse the Luma Key effect. EFFECTS ER FUNCTIS E-WY SOURCE L- REVERSE SOURCE - CK 5 MODE CTROL DIGITL EFFECTS STILL L UDIO LEVEL R P MODE CTROL FUNCTIS SOURCE SELECT /UDIO ER E-WY REVERSE q ⓭ TIME POSITI y L- SOURCE EFFECTS ER SOURCE - ➏ ➐ ➑ FUNCTIS ➒ ➓ ⓫ E-WY REVERSE r How to use the LUE effect: 2 MODE CTROL L- - qpress the button ⓯ to place the unit in mode. SOURCE SELECT 3 2Press one of the -bus selection buttons to select a source. 3Press one of the -bus selection buttons to select a source. HD INPUT 1 HD INPUT 2 SD INPUT 1 DIGITL EFFECTS SD INPUT 2 E-WY REVERSE 4Press the LUE button ➓. The blue areas of the picture will become transparent and TIME allow the image FUNCTIS of E-WY the other source to show through. ➓ 5Use the Video Slider to control the LUM level. HD INPUT 1 HD INPUT 2 SD INPUT 1 SD INPUT 2 6Press button ➏ or ➐ to change the source that is being keyed. 7Press the lue ➓ again to reverse the LUE effect. 7.9 UTO FDE/ Selection Reset the operation panel to initial mode: SOURCE SOURCE CK /UDIO ER TIME POSITI 1 t SOURCE SELECT STILL EFFECTS ER UDIO FOLLOW FUNCTIS ➑ UTO SOURCE / STRT L- L UDIO LEVEL R -15 SOURCE 2 - CK ➐ PINT MOSIC INPUT NEGTIVE POSITI INPUT 3 r SOURCE SELECT UX EFFECTS ER MODE CTROL ⓫ D D DJUST DJUST MIC DEMO SCN REVERSE SOURCE SOURCE L- 21 UDIO FOLLOW UTO / STRT - /UDIO ER DIGITL EFFE UD

21 1Press the button to enter UTO FDE/ mode. 2FDE/ transition time can be adjusted with the TIME control ➊. 3Press the button ⓬ to select the wipe effect. 4Press the button ⓮ to select (FDE) effect. 5Press the STRT button to start uto wipe or fade effect. NOTE: When in UTO FDE/ mode the Video Slider is disabled DIGITL EFFECT Digital effect section which generates special effects for the bus and -bus source video signals. The selected effect(s) can be added to either the -bus or -bus or both simutaneously. Effects can also be combined e.g. MOSIC and NEGTIVE can be combined to make a negative mosiac image. NOTE: The mosaic effect is not available in the picture-in-picture frame in mode. ⓲/ ⓳/ / / -bus, -bus digital effect button. STILL button - creates a still frame. PINT button - creates a 'paint' effect. Repeatedly pressing the PINT button will cycle through 3 levels of the effect. DIGITL EFFECTS ⓲ ⓳ ⓴ NEGTIVE button - creates a negative image. / MOSIC button - creates a 'pixellated' effect. Repeatedly pressing the MOSIC button will cycle through 3 levels of the effect. STILL PINT NEGTIVE MOSIC 7.11 UDIO ER The udio can be controlled either separately or in combination with a video source. /UDIO ER INPUT INPUT UX MIC In UDIO FOLLOW mode the audio will be controlled with the Video Slider as well as the video. When the LED is off the udio will be adjusted by and buttons. djusts the -bus source's audio level. djusts the -bus source's audio level. UX: Controls the audio level of the auxiliary input. MIC: Controls the audio level of the microphone input. UDIO FOLLOW UTO / STRT 22

22 7.11 OSD DJUST Connecting a display via the SD PREVIEW output will allow access to the on-screen display. When not in OSD DJUST mode the output will show /-bus and output system information. INFORMTI INPUT: SYSTEM:1080i60 INPUT:Y P PR 1 SYSTEM:480p60 OUTPUT:NTSC F/W Version DIGITL EFFECTS ⓲ ⓳ ⓴ STILL PINT NEGTIVE MOSIC DJUST DJUST DEMO SCN When in OSD DJUST mode, output will show the setup adjustment menu screen as shown below. When in MENU mode, press ⓳ t ⓴ u to adjust the page. Press MENU [1][2][3] and p to select the functions; once the functions are selected press t and ⓴ u to adjust the values. PICTURE CTRST [ 58] RIGHT [ 31] [ 31] HUE [ 31] DETIL [ 10] SPECT [FULL] NOTE: The values are not saved to the unit's memory until you exit the OSD DJUST mode. When the unit is turned off the system will change the value back to its default value. Press DJUST to exit the OSD adjust screen and the system will automatically save to the memory. CTRST [ 58] 0~63 RIGHT [ 31] 0~63 [1] PICTURE [ 31] 0~63 HUE [ 31] 0~63 DETIL [ 10] 0~63 SPECT [ F U L L ] UTO FULL 16:9 4:3 CTRST [ 58] 0~63 RIGHT [ 31] 0~63 MENU [2] PICTURE [ 31] 0~63 HUE [ 31] 0~63 DETIL [ 10] 0~63 SPECT [ F U L L ] UTO FULL 16:9 4:3 UDIO [ U T O ] UTO-CH1-CH2-CH3-CH4-CH5-CH6 UDIO [ U T O ] UTO-CH1-CH2-CH3-CH4-CH5-CH6 [3]SETUP VOLUME [ 127] 0~127 LIP SYNC [ 33MS] 0~170 OUTPUT [ N T S C ] NTSC-NTSC 43-PL-PL M-PL N DEFULT SECM-480P60-576P50-720P50-720P I I60 23

23 8. CNECTOR ND INSTLLTI 8.1 Front Panel Connections Microphone Input Headphone Output 8.2 Rear Panel Connections HD1 (YPbPr) HD2 (YPbPr) Other udio Source Monitor HD UDIO INPUT SD UDIO INPUT UX INPUT UDIO OUTPUT R1 L1 R2 L2 R1 L1 R2 L2 R L R1 L1 R2 L2 Y HD INPUT 1 Pb Pr SD INPUT 1 V S HD OUTPUT 1 SD PREVIEW Y Pb Pr V S HDMI INPUT HDMI OUTPUT DC INPUT 12V Y Pb HD INPUT 2 Pr V SD INPUT 2 S Y Pb HD OUTPUT 2 Pr V SD OUTPUT S SD1 SD2 TV TV or Recording Device 8.3 Output Resolutions The output resolution/system can set via the on-screen display on the SD PREVIEW output to adjust the output system or the output can be set by pressing a combination of two keys for 1 second. The combinations below: 24 button + button = 480p60 button + button = 576p60 button + button = 720p50 button + button = 720p60 button + button = 1080i50 button + button = 1080i60 button + button = NTSC button + button = NTSC 43 button + button = PL button + button = PL M button + button = PL N button + button = SECM50 9. SPECIFICTIS

24 SOURCE INPUT 6 (SOURCE 1/6) HDMI Input 2 Digital Video YUV(480i/p,576i/p,720p50/60,1080i50/60, 1080p50/60). Component Input 2 nalog Video YUV(480i/p,576i/p,720p50/60,1080i50/60). Y/C input 2 Y signal: 1.0 Vp-p 75Ω, Mini Din 4-pin connector C signal: 0.3 Vp-p 75Ω, Mini Din 4-pin connector Video input Vp-p 75Ω composite signal, Pin-Jack (NTSC,NTSC4.43,PL,PL-M,PL-N,SECM) udio input 4 6 ds/20 kω Pin Jack (L/R). EXTERNL SOUND INPUT MIC input 1 (MIC); 60 dv/600ω UX input 1 (UX); 6 ds/20 kω, Pin Jacks(L/R) RECORDING OUTPUT HDMI Output 1 Digital Video YUV(480i/p,576i/p,720p50/60,1080i50/60). Component Output 2 nalog Video YUV(480i/p,576i/p,720p50/60,1080i50/60). Y/C Output 1 Y signal: 1.0 Vp-p 75Ω, Mini Din 4-pin connector C signal: 0.3 Vp-p 75Ω, Mini Din 4-pin connector Video Output Vp-p 75Ω composite signal, Pin-Jack (NTSC,NTSC4.43,PL,PL-M,PL-N,SECM) udio Output 2 6 ds/20 kω Pin Jack (L/R). PREVIEW OUTPUT(OSD) Y/C Output 1 Y signal: 1.0 Vp-p 75Ω, Mini Din 4-pin connector C signal: 0.3 Vp-p 75Ω, Mini Din 4-pin connector Video Output Vp-p 75Ω composite signal, Pin-Jack (NTSC,NTSC4.43,PL,PL-M,PL-N,SECM) HEDPHE OUTPUT EFFECTS CK X3 PTTERNS S/N (TYPICL) POWER SOURCE POWER CSUMPTI DIMENSIS WEIGHT Headphone 1; 20 dv~ 80 dv, 8Ω unbalanced, phone-5 jack Video: Still, Mosaic, Paint, Negative, Wipe, Mix, Fade, Picture-In-Picture, Chroma key, Luminance key White, Yellow, Cyan, Green, Magenta, Red, lue, lack 96 patterns Video: 48 d (composite), 50 d (HDMI,Component,Y/C) udio: 60 d 12 V DC 3 pprox. 15 W 267(W) 370(D) 103.5(H) mm 2 Kgs 25