APPENDIX C - SP2100 1D LASER Setup Barccodes

Transcription

1 APPENDIX C - SP2100 1D LASER Setup Barccodes C.A - Method of programming the SP2100 1D Laser decoder with Setup Barcodes The decoder on the SP2100 1D laser scanner is the firware chip directly related to the hardware that makes the scan beam be projected out of and the reflected light sensed by the scanner. This isn t the same as the System Menu commands listed in the User s Guide before the appendicies. Programming the decoder directly gives you an even greater control of what types of barcodes can be read and how they are formatted before being sent to the SP2100 s firmware programming and ultimately to your connected host. CRITICAL! These barcodes set the decoder in the SP2100 1D Laser Scanner ONLY!!! If you have an imager and use these codes to change the settings in the SP2100 2D Imager decoder, you can verify you re using the right codes by looking for this mark in the top right of the page. If you have the SP2100 2D Laser Scanner, use the Decoder Setup Barcodes in Appendix B. The methodology for changing the setup options for the laser scanner include scanning a program on barcode, followed by the barcode denoting the combined symbology type and symbology option being changed, then scannign a 2-digit numeric code that represents enable/disable or other setting, and finally scanning a program off barcode. Because the laser scanner can be precisely aimed and the barcodes in this appendix can therefore be smaller, we ve included all the barcodes to change a particular symbology option together in a group surrounded by a red box. To set the option, all you have to do is scan each of the barcodes in the option s box from top to bottom. From Appendix H, you can see the full list of barcodes your SP2100 supports, depending on whether you have the 1D or 2D model. In this Appendix the defaults are marked with a red star beside them for easy identification. Denotes Decoder System Default Successfully Reading Setup Barcodes: For the purposes of the User s Guide, the setup barcodes may be packed densely enough that your SP2100 may read a code adjacent to the one you intend. Just put a piece of white paper or an index card ver the nearby barcode so the imager of the SP2100 can t see the adjacent code. C.A1 - Length Barcodes for Maximum and Minimum Barcode Length Some symbologies allow you to set numeric values for specific symbology options. For example, Code 39 allows you to set a Maximum Length and Minimum length. Use the barcodes below to enter the numeric digits required. 46

2 C.1 - UPC-A (Code ID: A) Enable UPC-A Disable UPC-A Enable Disable Enable Truncate Leading Zeros Disable Truncate Leading Zeros Enable Expand To EAN-13 Disable Expand To EAN-13 Digits - None Digits - 2 Digits - 5 Digits - 2 or 5

3 C.2 - UPC-E (Code ID: D) Enable UPC-E Disable UPC-E Enable Disable Enable Truncate Leading Zeros Disable Truncate Leading Zeros Enable Expand To EAN-13 Disable Expand To EAN-13 Enable Expand To UPC-A Disable Expand To UPC-A Digits - None Digits - 2 Digits - 5 Digits - 2 or 5

4 C.3 - UPC-E1 (Code ID: D) Enable UPC-E1 Disable UPC-E1 Enable Disable Enable Expand To UPC-A Disable Expand To UPC-A Enable Expand To EAN-13 Disable Expand To EAN-13 Digits - None Digits - 2 Digits - 5 Digits - 2 or 5

5 C.4 - EAN-13 (ISBN/ISSN) (Code ID: B) Enable EAN-13 Disable EAN-13 Enable Disable Enable ISBN/ISSN Conversion Disable ISBN/ISSN Conversion Digits - None Digits - 2 Digits - 5 Digits - 2 or 5 C.5 - China Post (Code ID: T) Enable China Post Enable China Post

6 C.6 - EAN-8 (Code ID: C) Enable EAN-8 Disable EAN-8 Enable Disable Enable EAN-13 Expansion Disable EAN-13 Expansion Digits - None Digits - 2 Digits - 5 Digits - 2 or 5 Enable Truncate Leading Zero Disable Truncate Leading Zero

7 C.7 - Code 39 (Code 32, Trioptic Code 39) - (Code ID: M) Enable Code39 Disable Code39 Enable Disable Enable Full ASCII Disable Full ASCII Enable Start/ Stop Char Transmit Enable Start/ Stop Char Transmit Enable * as Data Character Disable * as Data Character Enable Convert To Code32 Disable Convert To Code32 Enable Code32 Prefix A Transmission Disable Code32 Prefix A Transmission

8 C.7 - Code 39 (Code 32, Trioptic Code 39), con t Enable TriOptic Code39 Disable TriOptic Code39 Enable TriOptic Code39 Start/Stop Disable TriOptic Code39 Start/Stop C.8 - UK/Plessey (Code ID: U) Enable UK/Plessey Disable UK/Plessey Enable Disable

9 C.9 - Interleaved 2 0f 5 (Code ID: I) Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 Enable Check Digit (USS) Disable Check Digit (USS) Enable Check Digit (OPCC) Disable Check Digit (OPCC) C.10 - Industrial 2 0f 5 (Code ID: H) Enable Industrial 2 of 5 Disable Industrial 2 of 5

10 C.11 - Matrix 2 0f 5 (Code ID: X) Enable Matrix 2 of 5 Disable Matrix 2 of 5 Enable Check Digit (USS) Disable Check Digit (USS) C.12 - Code 93 (Code ID: L) Enable Code 93 Disable Code 93 Enable Disable

11 C.13 - Codeabar (Code ID: N) Enable Codabar Disable Codabar Enable Disable Start/End Character Type - ABCD/ABCD Start/End Character Type - abcd/abcd Start/End Character Type - ABCD/TN*E Start/End Character Type - abcd/tn*e Enable Start/ End Transmit Disable Start/ End Transmit Enable Enforce Start/End Equality Disable Enforce Start/End Equality

12 C.14 - Code 128 (Code ID: K) Enable Code 128 Disable Code 128 Enable Disable Disable Truncate Leading Zeros Enable Truncate All Leading Zeros Enable Truncate First Leading Zero

13 C.15 - UCC / EAN 128 (Code ID: K) Enable UCC/EAN 128 Disable UCC/EAN 128 Enable Disable Disable Truncate Leading Zeros Enable Truncate Leading Zeros Section CXX Section CXX

14 C.16 - ISBT 128 (Code ID: K) Enable ISBT 128 Disable ISBT 128 Enable Disable C.17 - Code 11 (Code ID: V) Enable Code 11 Disable Code 11 Enable Disable

15 C.18 - MSI / Plessey (Code ID: O) Enable MSI/Plessey Enable MSI/Plessey Enable Disable C.19 - GS1 Databar Truncated (Code ID: R) Enable GS1 Databar Truncated Disable GS1 Databar Truncated Enable Convert to UCC / EAN-128 Enable Convert to UPC-A/ EAN-113 Disable All Conversion

16 C.20 - GS1 Databar Limited (Code ID: R) Enable GS1 Databar Limited Disable GS1 Databar Limited Enable Convert to UCC / EAN-128 Enable Convert to UPC-A/ EAN-113 Disable All Conversion C.21 - GS1 Databar Expanded (Code ID: R) Enable GS1 Databar Expanded Disable GS1 Databar Expanded Enable Convert to UCC / EAN-128 Disable All Conversion