Precautions IMPORTANT WARNING CAUTION CAUTION. Precautions

Transcription

1

2 Precautions IMPORTANT The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION : TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence fo importantoperating and maintenance(servicing) instructions in the literature accompanying the appliance. These labels can be found on the unit's rear panel. Ces étiquelttes se trousent sur le fond de Pappareil. Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/tv technician for help. CAUTION This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. CAUTION Use of controls or adjustments or performance of procedures other than those specified here may result in hazardous radiation exposure. The use of Optical instruments with this product will increase eye hazard. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS. CAUTION This product contains a laser diode of higher class than. To ensure continued safety, do not remove any covers or attempt to repair. Refer all servicing to qualified personnel. The following caution appears on rear of the unit. CAUTION : LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM. VORSICHT : LASERS TRAHLUNG, WENN ABDECKUNG GEÖFFENT NIICHT DEM STRALHL AUSSETZEN! ADVARSEL : LASERSTRÄLING VED ÃBNING UNDGÃ UDSÆ TTEL SE FOR STRÃLING. VARNING : LASERSTRÃL NING NÃR DENNA DEL ÃR ÖPPNAD BETRAKTA EJ STRÃLEN. VARO! : AVATTAESSA ALTISTUT LASERSÃTBL YLLE ÃLÃ KATSO SÃTEESEN CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM (WARNING LOCATION: INSIDE ON LASER COVERSHIELD) This product is in conformity with the EMC directive and low-voltage directive. This product incorporates copyright protection technology that is protected by method claims of certain U.S Patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be Authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Manufactured under license from Dolby Laboratories. Dolby and the double-d symbol are trademarks of Dolby Laboratories. DTS and DTS Digital Surround are trademarks of Digital Theater Systems, Inc. Product label concerning product safety standard is pasted in the middle of bottom cover of recorder. Precautions

3 Important Safety Instructions READ THESE INSTRUCTIONS - All the safety and operating instructions should be read before the product is operated. KEEP THESE INSTRUCTIONS - The safety and operating instructions should be retained for future reference. HEED ALL WARNINGS - All warnings on the product and in the operating instructions should be adhered to. FOLLOW ALL INSTRUCTIONS - All operating and use instructions should be followed. CLEAN ONLY WITH A DAMP CLOTH - Unplug this product from the wall outlet before cleaning. The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzene secticides or other volatile liquids since they may corrode the cabinet. DO NOT USE THIS APPRATUS NEAR WATER - Do not use this product near water - for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. ACCESSORIES - Only use the attachments/accessories specified by the manufacturer. CART - Use only with a cart, stand, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. VENTILATION - Do not block any of the ventilation openings. Install in accordance with the manufacturer's instructions. GROUNDING OR POLARIZATION - Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your oulet, consult an electrician for replacement of the obsolete outlet. POWER-CORD PROTECTION - Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. LIGHTNING - Unplug this apparatus during lightning storms or when unused for long periods of time. SERVICING - Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled over, objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. HEAT - Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus(including amplifiers) that produce heat. Important Safety Instructions

4 Table of Contents Before You Start What s in the box... 6 Putting the batteries in the remote control... 6 Using the remote control... 6 Compatible Discs... 7 Controls & Display Front Panel... 8 Display... 9 Rear Panel... 0 Remote Controller Unit... Connection Connection for Video Output Terminals... Connection for Audio Output Terminals... 5 Connection for A/V Input Terminals... 5 Connection for DV IN and USB IN... 6 Connection for HDMI Output... 6 Getting started Turning on and off... 7 Selecting the HDD or DVD for playback and recording... 7 Displaying the disc information on screen (OSD)... 7 Basic Playback Playing a DVD disc... 8 Playing a DVD±RW or DVD±R disc... 8 Playing an Audio CD... 8 Playing a JPEG CD... 9 Playing MPEG- Movie CD... 9 Playing a program of HDD... 0 Playing a JPEG in HDD... 0 Playing MPEG- Movie in HDD... Advanced Playback Fast Forward/Backward... Skip Forward/Backward... Slow Forward... Frame by Frame Playback (DVD/VCD only)... Program Playback (Audio CD only)... Selecting Subtitles (DVD only)... Selecting Audio Languages (DVD only)... Repeating a Title, Chapter (DVD/Audio CD only)... 5 A-B Repeat (DVD/Audio CD only)... 5 ZOOM screen (DVD/HDD only)... 6 Switching the Camera Angle (DVD only)... 6 Direct Search (DVD only)... 7 Recording Basic recording... 8 OTR (One touch Timer Recording)... 8 Timer Recording... 9 Timer review - changing and erasing record settings... 0 Recording from a DV (Digital Video) camcorder... Time Shifted Recording... Simultaneous recording and playback... Copying Copying the DVD titles from Disc to HDD... Copying the titles from HDD to Disc... Copying the files from disc to HDD (from HDD to Disc)... Copying the files from the USB flash memory to HDD (or disc)... 5 Editing Editing a DVD±RW or DVD±R disc Play disc (DVD±RW/DVD±R)... 7 Rename disc (DVD±RW/DVD±R)... 7 Erase optical disc (DVD±RW only)... 8 Overwrite disc (DVD±RW only)... 8 Finalize disc (DVD±R only)... 9 Lock disc (DVD±RW only)... 9 Copy All (DVD±RW/DVD±R)... 9 Table of Contents

5 Table of Contents Editing a title of DVD±RW or DVD±R Play title (DVD±RW/DVD±R)... 0 Edit title (DVD±RW/DVD±R)... 0 Rename title (DVD±RW/DVD±R)... Erase title (DVD±RW only)... Overwrite title (DVD±RW only)... Append title (DVD±RW/DVD±R)... Copy title (DVD±RW/DVD±R)... Editing the title of HDD Play... Delete... Split... Segment... 5 Combine... 5 Change Index Picture... 5 Rename... 5 Lock... 6 Unlock... 6 Protect... 6 Unprotect... 6 Using the Setup Menu Basic Operations... 7 Record & Channel Scan... 7 Video Audio... 5 Language... 5 Clock... 5 General... 5 HDD... 5 Additional Information Specifications Troubleshooting Table of Contents 5

6 Before You Start What's in the box Thank you for buying this product. Please confirm that the following accessories are in the box when you open it. Accessories Insert two AAA batteries into the battery compartment following the indications (+, -) inside the compartment. Close the cover. RF cable Remote control Scart cable Audio/Video cable AAA dry cell batteries Operating instruction (this manual) Using the remote control Keep in mind the following when using the remote control : Make sure that there are no obstacles between the remote and the remote sensor on the unit. Remote operation may become unreliable if strong sunlight or fluorescent light is shining on the unit's remote sensor. Remote controllers for different devices can interfere with each other. Avoid using remotes for other equipment located close to this unit. Replace the batteries when you notice a fall off in the operating range of the remote. Putting the batteries in the remote control Open the battery compartment cover on the back of the remote control. Incorrect use of batteries can result in hazards such as leakage and bursting. Please observe the following: Don't mix new and old batteries together. Don't use different kinds of batteries together-although they may look similar, different batteries may have different voltages. Make sure that the plus and minus ends of each battery match the indications in the battery compartment. Remove batteries from equipment that isn't going to be used for a month or more. When disposing of used batteries, please comply with governmental regulations or environmental public instruction s rules that apply in your country or area. 6 BEFROE YOU START

7 Before You Start Compatible Discs Any disc that displays one of the following logos should play in this system. Other formats, including DVD-RAM, DVD-ROM, DVD-Audio, SACD and CD-ROM will not play. DVD Video compatibility Single-sided or double-sided discs. Single layer or dual layer discs. Dolby Digital, DTS, MPEG or Linear PCM digital audio. MPEG- digital video Discs are generally divided into one or more titles. Titles may be further subdivided into chapters. Audio CD compatibility cm or 8cm discs. Linear PCM digital audio. CD-Audio, CD-R and CD-RW formatted CDs are divided into tracks.(this unit can play CD-R and CD-RW discs recorded in CD Audio or Video CD format, or Kodak picture CD files.) MPEG- CD compatibility JPEG CD compatibility JPEG Photo in Discs. DVD Video regions All DVD Video discs carry a region mark on the case somewhere that indicates which region of the world the disc is compatible with. Your DVD recorder also has a region mark, which you can find on the rear panel. Discs from incompatible regions will not play in this recorder. Discs marked ALL will play in any player. CAUTION Also this can play MPEG- disc. If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. Some of MPEG- movies could not be played depending on the encoding methods. DVD-R/RW compatibility DVD+R/RW compatibility This unit can play DVD-R/ DVD-RW discs recorded as DVD video format. Also this unit can record the video and audio signal in DVD-R/DVD-RW discs. This unit can play DVD+R/ DVD+RW discs recorded as DVD video format. Also this unit can record the video and audio signal in DVD+R/DVD+RW discs. Before You Start 7

8 Controls & Display Front Panel DISC TRAY Put a disc to be played in here. OPEN/CLOSE To open or close the disc tray. 5 FL DISPLAY Displays operation status. JOG Button (PLAY/PAUSE ( ) ARROW ( )) Press to start or pause a disc playing. And used to navigate or select an item of menu. This button has also alternate functions as like Stop(Down), Previous(Left) and Next(Right) Skip. USB IN Digital input jack for use with a digital camera, USB memory. 6 DV IN Digital input jack for use with a digital video camcorder. This jack is for connection to DV camcorder only. It is not compatible with other digital equipments. 7 STANDBY/ON To switch the unit on or into Standby. 8 9 COMPOSITE VIDEO IN Connect to Composite Video Output of camcorder. AUDIO IN Connect to Audio Output of camcorder. 8 Controls & Display

9 Controls & Display Display TIMER Recording Indicator Lights when timer recording is on. ANGLE Indicates the current disc being played is viewed as multi angle. This function only works for discs having scenes recorded at different angles. 5 DOLBY DIGITAL Indicator Indicates Dolby Digital 5.CH playback. TITLE Indicator Title number for DVD playback. CHAPTER Indicator Chapter number for DVD playback. BILINGUAL Indicator Illuminates when receiving a bilingual broadcast. 8 ROTATION Rotates when the disc is spinning. 9 0 HDD Indicator Indicates the HDD mode. REPEAT Indicator Illuminates when the current play mode is under repeat title, chapter, track, A-B respectively. DVD Indicator Indicates the DVD mode. DTS Indicator Illuminates when the format of digital audio output is DTS. OPERATING Information Indicates title, Chapter and Track number and Time, TV channel. 7 STEREO Indicator Illuminates when receiving a stereo broadcast. Controls & Display 9

10 Controls & Display Rear Panel AC POWER CORD Connect to the wall outlet. DIGITAL AUDIO OUT Connect COAXIAL OUT to Digital Audio Input (coaxial type) of Audio AMP. Or connect OPTICAL OUT to Digital Audio Input (optical type) of Audio AMP. COMPONENT VIDEO OUT Connect to Component Video Inputs of TV. AUDIO IN Connect to Audio Output of VCR or Set-Top Box. VIDEO IN Connect VIDEO to Composite Video Output of VCR or Set-Top Box. Or connect S-VIDEO to S-Video Output of VCR or Set-Top Box. VIDEO OUT Connect VIDEO to Composite Video Input of TV or monitor. Or connect S-VIDEO to S-Video Input of TV or monitor. S-Video provides better picture quality than composite video AUDIO OUT Connect to Audio Input of TV. HDMI OUT (576P) HDMI(High Definition Multimedia Interface) transfers the digital video and audio from your DVD Recorder to your TV. Simply connect your DVD Recorder to your TV with a single HDMI cable for the best picture and sound. ANT IN Connect to external antenna. ANT OUT Connect to Antenna Input of TV. EURO AV OUT Connect to Euro AV input of TV. EURO AV IN/OUT Connect to Euro AV in/out of AV equipment such as VCR, DVD player, etc. 0 Controls & Display

11 Controls & Display Remote Controller Unit A A-B To repeat a certain section during playback. ADD/CLEAR To remove the preset program on the timer recording list. To add or delete the track No. on the program playback list of CD. ANGLE To view with a different frame angle. ARROW ( ) To select an item of menu. AUDIO To select the audio language or audio channel when playing a DVD disc. You can also change the audio channel of the broadcast. If the NICAM broadcast is bilingual, you can select the language. If the NICAM broadcast is stereo, you can switch between NICAM stereo and Mono audio. AV IN To select an external audio and video input to use for recording. C CHANNEL DOWN/UP (-/+) To select the preset TV channels. Controls & Display

12 Controls & Display DISPLAY To view the Title, Chapter, Track information or Subtitle Language, Audio Language. DVD To switch to DVD mode. DV/USB To select a digital A/V input from a DV camcorder or USB flash memory. ENTER To select the menu item. MENU To display the contents menu of the loaded DVD disc. N NEXT ( ) To skip to the next chapter or track. NUMERIC (0~9) To use the number buttons for track/chapter/title selection. D E EDIT To edit a title or chapter of disc. FILE To view the file list. (MPEG-, MP, JPEG files) F H HDD/DUB To switch to HDD mode. To copy the titles from HDD to disc. M MUTE To turn on/off audio outputs. O OPEN /CLOSE ( ) To open or close the disc tray. If pressed under STANDBY, power is automatically turned on. P PAUSE ( ) When you press this button during playback, you can view the still picture. Each time you press this button, you can see one frame at a time. PLAY ( ) To play the loaded disc or HDD. PREV ( ) To skip to the previous chapter or track. PROGRAM To playback in a specific order. This button works only when the CD is played back. REC (Record) To start recording. REPEAT To select a repeat mode. R RETURN To move to a previous menu. When using VCD.0 and SVCD with PBC function, this button works as a RETURN button. SCAN FWD ( ) To start forward scanning during playback. SCAN REV ( ) To start reverse scanning during playback. S SETUP To change the initial settings. Controls & Display

13 Controls & Display SLOW ( ) To play the disc contents in slow forward. SORT/PIP To sort the titles of HDD in the order of the title name or date. To view the external video while the DVD or HDD is played back. STANDBY/ON ( ) Activates the unit POWER ON or into STANDBY. Z ZOOM Enlarges DVD or HDD screen image up to times. STOP ( ) To stop a disc or HDD playing. SUBTITLE To select the subtitle language. TIMER REC To set a timer recording. TIMESHIFT To store a TV program in the HDD storage cache temporarily. TITLE To display the title menu of the DVD. T TV To switch to the TV mode. TV/DVD To view channels selected by the recorder tuner or by the TV tuner. It works only when recorder and TV is connected by European Scart cable while SCART out setting is RGB in Setup Menu. TV MODE Set up TV type according to type supported by user s TV. Each time you press this button repeatedly, the TV type will change among NTSC, PAL and progressive scan/hdmi. This button works only when the disc tray is open. Controls & Display

14 Connection Connection for Video Output Terminals Composite Video (CVBS) Output The composite video output is supported by most televisions. The composite video jack on TV is usually yellow and may be labeled video, CVBS, composite. EURO AV Output The Euro AV terminal can be connected to the TV equipped with Euro AV connector. The audio transmitted on the Euro AV is stereo sound. S-Video Output The S-Video output can be connected to the TV equipped with an S-Video input. The S-Video jack on TV may be labeled S-Video, Y/C, S-VHS. The S-Video provides better picture than the composite video. Component Video Output The component video output can be connected to the TV equipped with component input. The component video jacks on TV may be labeled YUV, Y/Pb/Pr, Y/Cb/Cr and may be green, blue, red. The component video provides the best picture. Set Video Output to YCrCb On from VIDEO SETUP menu. RF OUT, is labeled TO TV, is signal pass-thru only. A S-Video cable is not supplied. Connection

15 Connection Connection for Audio Output Terminals You can enjoy the Dolby surround sound by connecting the digital audio output to the audio amplifier. Audio Output Use audio outputs for connection with your TV. Digital Audio Output Use digital audio outputs for connection with Dolby Digital or DTS decoder. From the Digital Audio Output menu, select PCM or Bitstream according to your decoder. An optical cable and coaxial cable are not supplied. Connection for A/V Input Terminals You can record programs from AV system such as VCR, Satellite receiver or Decoder box. Audio Input Connect the Audio Input to the Audio Output of AV system. Video Input Connect the Composite Video or S-Video Input to the Composite Video or S-Video Output of AV system. Or connect the Euro AV IN/OUT to the Euro AV OUT of AV system. Connection 5

16 Connection Connection for DV IN and USB IN Using the DV IN, it is possible to read digitally the contents of DV tapes. DV Input Connect the DV IN to the DV in/out jack on your DV camcorder using a DV cable (not supplied). USB Input Insert the USB memory in the USB jack of this recorder. Connection for HDMI Output HDMI (High Definition Multimedia Interface) transfers the digital video and audio from your recorder to your TV. Connect the HDMI Output to the HDMI Input of TV with a single HDMI cable. 6 Connection

17 Getting started Turning on and off Turn on your TV and set the video input to this recorder. Press STANDBY/ON button on the remote controller or the front panel to turn on. You can see the on-screen information. If you want to turn off, press STANDBY/ON button again on the remote controller or the front panel. Selecting the HDD or DVD for playback and recording If you want to switch to the HDD mode, press HDD/DUB button on the remote control. Displaying the disc information on screen (OSD) You can display the playback status on TV screen as follows ; Title, Chapter number, Playing time. Press DISPLAY button during playback. Title, Chapter number, Playing time, Audio language and Subtitle appear on TV screen. Press DISPLAY button once more. You can see the playback status in detail. Also you can change the subtitle language, chapter, and so on using,,, ENTER button. If you want to switch to the DVD mode, press DVD button on the remote control. To turn off the on-screen display, press DISPLAY button. Getting started 7

18 Basic Playback Playing a DVD disc Press OPEN/CLOSE button to open the disc tray. Put a disc on the disc tray with logo-printed side up. Press OPEN/CLOSE button again to close the disc tray. The disc will be loaded automatically. Playing an Audio CD Load an Audio CD. The first song is played back automatically. Press DISPLAY button. The disc information is displayed on the TV screen. The TV screen shows disc menu. Select the desired item by using,,, or 0 to 9 button, then press ENTER or PLAY button to start playback. Playing a DVD±RW or DVD±R disc Load a DVD±RW or DVD±R disc. The menu screen is displayed automatically. <Audio CD> Select TRACK by using or button, and press ENTER button. Enter the desired track No. by using 0 to 9 button, and press ENTER button. The selected song is played back. If you press or button during playing back, you can hear the next song or the previous song. Select the desired program by using or button. Press ENTER or PLAY button to start playback. Press TITLE or MENU button to return to the menu screen. 8 Basic Playback

19 Basic Playback Playing a JPEG CD Load a JPEG CD. The directory & file list is displayed on the TV screen. Playing MPEG- Movie CD Load a MPEG- disc. 5 Select the desired file by using or button. You can see the thumbnail picture of selected file on the right window. Press ENTER button to start playback. The JPEG files are played in order automatically. If you press or button during playing back, you can see the next picture or the previous picture. Picture rotation and zoom You can rotate the picture to the left or right by using or button. Also you can enlarge the picture up to times or reduce it up to a quarter by using or button. To see the file list, press STOP button. The file list is displayed on the TV screen. Press Enter button after selecting the directory of Disc using, button. Press Enter button after selecting the desired movie using, button. The selected movie is played back. Some of the MPEG- movies could not be played depending on encoding method. Basic Playback 9

20 Basic Playback Playing a program of HDD Press HDD/DUB button to select the HDD mode. The program list of HDD appears on screen. Playing a JPEG in HDD Press FILE button. the directory of HDD using or button. The file list of HDD appears on screen. Select the desired program by using or button in the program list. Press PLAY button. It starts to play the selected program. Select the desired file by using or button. You can see the thumbnail picture of selected file on the right window. Press ENTER button to start playback. The JPEG files are played in order automatically. If you press or button during playing back, you can see the next picture or the previous picture. 5 Picture rotation and zoom. You can rotate the picture to the left or right by using or button. 6 To see the file list, press STOP button. The file list is displayed on the TV screen. 0 Basic Playback

21 Basic Playback Playing MPEG- Movie in HDD Press FILE button. the directory of HDD using or button. The program list of HDD appears on screen. the desired movie using, button. To see the file list, press STOP button. The file list is displayed on the TV screen. Some of the MPEG- movies could not be played depending on encoding method. Basic Playback

22 Advanced Playback Fast Forward/Backward Use this function to play the DISC or HDD contents in fast forward or fast reverse. There is no sound during searching. Press or button during play mode. Each time you press the button, playback speed changes as below. Slow Forward Use this function to play the DISC or HDD contents in slow forward. Press SLOW button during play mode. The disc content is played slowly in forward. Press SLOW button. Each time you press the button, playback speed changes as below. Press PLAY button to resume normal playback. Skip Forward/Backward (DVD/Audio CD only) Use this function to move to the next or previous chapter for DVD, track for Audio CD. Press PLAY button to resume normal playback. Press button during play mode. The DVD Recorder starts playing the previous chapter or track. Press button during play mode. The DVD Recorder starts playing the next chapter or track. Frame by Frame Playback (DVD/VCD only) Press PAUSE button during play mode. The DVD Recorder pauses the playing temporarily. Press PAUSE button repeatedly. Each time you press, one frame is displayed at a time. Press PLAY button to resume normal playback. There is no sound during viewing Frame playback or Slow playback. Audio CD do not have Frame Playback and Slow Playback feature. Advanced Playback

23 Advanced Playback Program Playback (Audio CD only) This feature lets you program the play order of tracks on a disc. Load an Audio CD. The first song is played back automatically. Press PROGRAM button. The track list is displayed on the TV screen. 6 7 To delete a song from the program list, select the song you want to delete by using,,, button, then press ADD/CL button. The selected song is erased from the program list. To exit the program list, press RETURN button. Select the desired song by using or button in the track list, then press ADD/CL button. The selected song is added on the right program list. Repeat step if you want to select other songs. 5 Move the cursor to the program list by pressing button, then press ENTER button. It starts playback of a saved program list. Advanced Playback

24 Advanced Playback Selecting Subtitles (DVD only) It is possible to change the subtitle language to a different language from the one selected at the initial settings. This operation works only with discs on which multiple subtitle languages are recorded. If the loaded disc supports multiple subtitles, you can select the subtitle language. Press SUBTITLE button during playing. The subtitle is displayed on the bottom of screen. Selecting Audio Languages (DVD only) It is possible to change the audio language to a different language from the one selected at the initial settings. This operation works only with discs on which multiple audio languages are recorded. If the loaded disc supports multiple audio languages, you can select the audio language. Press AUDIO button during playback. The audio information is displayed on the top of screen. Each time you press SUBTITLE button, the subtitle language is changed. To turn off the subtitle, select OFF by pressing SUBTITLE button. Each time you press AUDIO button, the audio language is changed. Some discs only allow you to change subtitle or audio language from the disc menu. Advanced Playback

25 Advanced Playback Repeating a Title, Chapter (DVD/Audio CD only) It is possible to repeat the chapter/title for DVD or track/disc for Audio CD. Press REPEAT button during playback. The repeat information is displayed on the top of screen. A-B Repeat (DVD/Audio CD only) Use this function to repeat the play of a selected segment. This is very useful for studying foreign languages because it repeats the selected segment until canceled. Press A-B/LANG button at the point of where repeat play is to start. The starting point of your selected segment is set up. Press A-B/LANG button again at the point of where repeat play is to end. The ending point is set up. It is played repeatedly from A to B. Each time you press REPEAT button, the repeat mode is changed as follows. To cancel the A-B repeating, press A-B/LANG button once more. The playing state changes to normal. We recommend you set up the desired segment within a minimum 5 seconds for smooth repeat play. With some DVD discs, there may be times when repeat playback is not possible. Advanced Playback 5

26 Advanced Playback ZOOM screen (DVD/HDD only) The zoom function allows you to enlarge DVD or HDD screen image up to times. Press ZOOM button during playback. The picture is zoomed. Switching the Camera Angle (DVD only) When a DVD contains recorded multiple angles of a scene, you can select the Angle function. Press ANGLE button during playing. Available angles of the current scene will be displayed on the top of screen. Each time you press ANGLE button, the angle is changed. Each time you press ZOOM button, the zoom mode will be changed : You can only change the angle for DVDs that provide multiple angles of scenes. The angle function will not work on DVD video discs that do not contain recorded multiple angles. You can move the image by using,,, button. To cancel the zoom mode, press ZOOM button repeatedly until the recorder resume to normal playback. You can t use this feature when the MPEG- movie is being played. 6 Advanced Playback

27 Advanced Playback Direct Search (DVD only) You can select a specific chapter or title to play. Press DISPLAY button twice during playback. The playback information appears on TV screen. Title Search Select TITLE by pressing, button, and press ENTER button. Enter the title number by using numeric 0 to 9 button, and press ENTER button. It starts to play back from the specified title. Chapter Search Select CHAPTER by pressing, button, and press ENTER button. Enter the chapter number by using numeric 0 to 9 button, and press ENTER button. It starts to play back from the specified chapter. Advanced Playback 7

28 Recording Basic recording To record TV programs, you should search TV channels first. Press HDD/DUB or DVD button to select the HDD(Hard Disk Drive) or a recordable DVD (DVD±R/DVD±RW) on which you want to record. If you want to record on the HDD, press HDD/DUB button. The HDD menu is displayed on TV screen. If you want to record on DVD, load a DVD±RW or DVD±R disc with enough free space for the recording. If you load a new blank disc, it asks for formatting the disc. OK. If the DVD menu is displayed on TV screen automatically, press STOP button twice to stop. Press AV IN button to choose the A/V source you want to record. Every time this button is pressed, the A/V source is changed : 5 Press REC button to start your recording. Press PAUSE button if you want to stop the recording for a short while. Press REC button to continue recording. Press STOP button to stop your recording. A DVD±R/DVD±RW can record for up to 6 hours, up to 9 titles. If your source is copy-protected, you will not be able to record it. OTR (One touch Timer Recording) During basic recording, press REC button. Every time you press REC button, the recording time will increase by 0 minutes. It is possible to record for up to hours if there is enough room on the disc (or HDD) and the record quality is SLP.(or the length of timeshift buffer is set to 60 minutes.) The DVD recorder will stop automatically after recording for a specific time. If you want to cancel OTR, press STOP button. If you want to record the TV program, select the TV mode. And choose the station you want to record by pressing CHANNEL or CHANNEL + button. 8 Recording

29 Recording Timer Recording For timer recording, the clock, date, and stations must be set correctly. If you want to record on DVD, load a DVD±RW or DVD±R disc with enough free space for the recording. Press TIMER REC button Select Quality by pressing button, and press ENTER button to bring up the list. Select the Record Quality by using or button, and press ENTER button to confirm. Select Mode by pressing button, press ENTER button to bring up the list. Select how often you want to make the recording, for example, once, daily or weekly by pressing or button, and press ENTER button to confirm. Select Date by pressing button, and press ENTER button. Enter the date by using 0 to 9 button, and press ENTER button to confirm. If you selected Weekly in step 6, press ENTER button after selecting a day of week by using or button. Select an unused program by pressing or button, then press ENTER button. 8 Select Start by pressing button, press ENTER button. Enter the Start time by using 0 to 9 button, and press ENTER button to confirm. Press ENTER button. The sub-menu appears. Select the signal source by using or button, and press ENTER button to confirm. Select Record To by pressing button, and press ENTER button to bring up the list. Select HDD for hard disc recording or DVD for DVD recording by using or button, and press ENTER button to confirm. 9 0 Select End by pressing button, press ENTER button. Enter the End time by using 0 to 9 button, and press ENTER button to confirm. Select Title by pressing button, press ENTER button. Enter the title name by using,,, button, and press ENTER button to confirm. Switch VPS/PDC ON or OFF by using, and ENTER button. (If Source is not set to TV channel, this function is not available.) The VPS/PDC system automatically adjusts the recording time so that even if a program is not running to schedule you won t miss it. For VPS/PDC to work properly, you must input the correct announced time and date of the program you want to record. Note that VPS/PDC may not work with every station. Recording 9

30 Recording OK by using button if all the settings are correct. Switch your DVD Recorder off by pressing STANDBY/ON button. You can switch your DVD Recorder on again if you want to set the timer to record another program. Remember to switch the DVD Recorder off when you have finished. To stop a timer recording which has already started, press STANDBY/ON or STOP button. You can pre-program the schedule to record up to 8 programs. We recommend you set up the recording time over 5 minutes. Timer review - changing and erasing record settings Press TIMER REC button. You can see all the timer programs currently set. 5 Select the program you want to change or erase by pressing or button. Erasing a setting Press ADD/CL button to erase. Changing a setting Press ENTER button. Select the details you want to change by pressing or button, and press ENTER button. Change the settings by using, or the number buttons 0 to 9. When you have made all the changes, press ENTER button. OK using button if all the settings are correct. Press TIMER REC button to exit. 0 Recording

31 Recording Recording from a DV (Digital Video) camcorder You can record the contents of DV tape from a DV camcorder via DV IN. Make sure your digital camcorder is connected to DV IN jack on the front panel. Also turn on your DV camcorder and set it to PLAY (or VCR) mode. 5 Press HDD/DUB or DVD button to select the HDD(Hard Disk Drive) or a recordable DVD (DVD±R/DVD±RW) on which you want to record. If you want to record on DVD, load a DVD±RW or DVD±R disc with enough free space for the recording. Press DV/USB button. Find the place on the camcorder tape that you want to start recording from. You can use the remote controller for this recorder to control the camcorder using PLAY, STOP, PAUSE,, button. For best results, press PAUSE button at the point from which you want to record. Press REC button to start your recording. Press PAUSE button if you want to stop the recording for a short while. Press again REC button to continue recording. Press STOP button to stop your recording. Depending on the connected camcorder, you may not be able to control it using the remote control supplied with this recorder. If this recorder does not recognize the DV camcorder, insert the DV cable again into the DV IN jack after pulling it from the DV in jack. Time Shifted Recording This recorder automatically saves the program on air in the HDD temporarily, this allows the user to manipulate the saved program using functions such as rewind, fast forward, replay and pause. Press the playback control buttons such as,,,,, while watching TV, the Time bar appears on the bottom of the screen. Pause If you press PAUSE button, the current program is paused. If you press PLAY button, the program is resumed from that point. Fast Forward/Backward Press or button during playback. Whenever you press the button, the playback speed increases by steps. Press PLAY button to resume normal playback. Skip Forward/Backward Press button during playback. The DVD recorder starts playing the previous chapter. Press button during playback. The DVD recorder starts playing the next chapter. Recording

32 Recording 5 Slow Forward Press SLOW button during playback. The current program is played slowly in forward. Whenever you press the button, the slow speed is changed by steps. 6 Recording While the time shift operation records the program temporarily, the record operation records the program permanently on HDD so you can playback the recorded program at anytime. Press REC button to start recording the current program. Press PLAY button to resume normal playback. Press STOP button to stop recording. This function is not available in the DVD mode. If you want to use the time shift recording, press TIMESHIIFT button while watching TV. If OSD Menu is shown on during Time Shift from A/V inputs and from digital TV, OSD Menu could be recorded together. Therefore please escape from the OSD Menu if you want to record Time Shift period. Simultaneous recording and playback You can playback a HDD title and record a TV program on the disc at the same time. Also you can playback a DVD title and record a TV program on HDD at the same time. Playing a HDD title while you record a TV program on the disc. Press HDD/DUB button during recording. The program list of HDD appears on screen. Playing a DVD title while you record a TV program on HDD. Press DVD button during recording. The disc menu appears on screen. Select the desired program by using or button in the program list. Press PLAY button to start playing. Select the desired item or the desired title using,,, button. Press ENTER or PLAY button to start playing. Recording

33 Copying Use the copying features of this recorder to: Back up important recordings stored on the HDD to a DVD. Make a DVD copy of a recording on the HDD to play in another player. Transfer video from a DVD to the HDD for editing. Transfer edited video from the HDD to DVD. Copyright Recording equipment should be used only for lawful copying and you are advised to check carefully what is lawful copying in the country in which you are making a copy. Copying of copyright material such as films or music is unlawful unless permitted by a legal exception or consented to by the rightowners. Copying a title from disc to HDD. Press DVD button. The title menu will show on the TV screen. Press button after selecting the title to copy by using or button. The edit menu will show on the TV screen. Copying the DVD titles from Disc to HDD Make sure the DVD disc to copy is inside of the recorder. Copy title by using or button. It starts to copy the selected title from DVD to HDD. Copying all titles from disc to HDD. Press DVD button. The title menu will show on the TV screen. Press button, and press button. The edit menu will show on the TV screen. Copy All by using or button. It starts to copy all titles from disc to HDD. Copying

34 Copying Copying the titles from HDD to Disc Make sure the recordable DVD (DVD±R/DVD±RW) is inside of recorder. Press HDD/DUB button. The title list of HDD will show on the TV screen. Copying the files from disc to HDD (from HDD to Disc) Make sure the disc to copy or recordable DVD (DVD±R/DVD±RW) is inside of the recorder. You can copy the MP files, JPEG files and MPEG- files from disc to HDD (or from HDD to disc). Press FILE button. The directory & file list will be displyed on the TV screen. the title to copy by using or button. A mark is put on the selected title. Repeat step if you want to select other titles. Press EDIT button. The copy menu will be displayed on the TV screen. Press HDD/DUB button. It starts to copy the selected titles from HDD to disc. copy using or button. Select the directory of source file to copy by using,, ENTER button. (If you want to copy the file of disc, select the DVD directory. If you want to copy the file of HDD, select the HDD directory.) The file list will show on the screen. Copying

35 Copying 5 Press ADD/CL button after selecting the file to copy by using or button. The selected file will be added on the right file list. Copying the files from the USB flash memory to HDD (or disc) Make sure the flash memory is inserted into the USB IN jack. If you want to copy the files on the disc, load a recordable DVD (DVD±R/DVD±RW). Press FILE button. The directory & file list will be displayed on the TV screen. 6 Repeat step 5 if you want to copy other files. 7 Press button. 8 Select the directory where you want to copy the selected files by using,, ENTER button. (If you want to copy the files from disc to HDD, select the subdirectory of HDD. If you want to copy the files from HDD to disc, select the DVD directory.) Press EDIT button. The copy menu will be displayed on the TV screen. 9 Press REC button. It starts copying the files from disc to HDD (from HDD to disc). 0 Press EDIT button to exit after finishing copying. Copy using or button. the USB directory by using or button. Copying 5

36 Copying 5 Press ADD/CL button after selecting the file to copy by using or button. The selected file will be added on the right file list Repeat step 5 if you want to copy other files. Press button. Select the directory where you want to copy the selected files by using,, ENTER button. (If you want to copy the files on the HDD, select the subdirectory of HDD. If you want to copy the files on the disc, select the DVD directory.) Press REC button. It starts copying the files from the flash memory to HDD (or disc). 0 Press EDIT button to exit after finishing copying. Don t use more than 500mA flash memories. If this recorder does not recognige the USB flash memory, insert the USB flash memory again into the USB IN jack after pulling it from the USB IN jack. 6 Copying

37 Editing Editing a DVD±RW or DVD±R disc Load a DVD±RW or DVD±R disc. The DVD menu screen is displayed automatically. Rename disc (DVD±RW/DVD±R) Rename disc by using or button. The keyboard will show on the screen. Press button to go to the top of the DVD menu. Press button, the Disc Edit menu will show on the screen. <DVD±RW> Select a letter which you want to input by using,,, button, and press ENTER button to confirm it. Repeat step. The maximum length of the disc name is up to 9 characters. The control bars of the bottom line in the keyboard is for edit command. If the inputting of letters is finished, press ENTER button after selecting OK. <DVD±R> Play disc (DVD±RW/DVD±R) You can play back the entire disc from the beginning to the end. Play by using or button. It starts to play back the beginning of the disc. Editing 7

38 Editing Erase optical disc (DVD±RW only) Erase optical disc by using or button. The pop-up menu will show on the screen. Overwrite disc (DVD±RW only) Overwrite disc by using or button. It will be changed from DVD mode to AV input mode. Press AV IN button to choose the A/V input you want to record. Every time this button is pressed, A/V input is changed : Press ENTER button to erase the contents of a disc after selecting Yes by using, button. It takes a few minutes to erase the disc. The Erase function only works on DVD±RW discs. If you want to record the TV program, select the TV mode. And choose the station you want to record by pressing CHANNEL or CHANNEL + button. Press REC button to start your recording. It starts to record from the beginning of the disc. Press STOP button to stop your recording. Recorded programs will be erased from the beginning if overwritten. 8 Editing

39 Editing Finalize disc (DVD±R only) If you want to make your DVD±R disc compatible with other DVD players or recorders, you should finalize the disc. Finalize disc by using or button. The pop-up menu will show on the screen. Press ENTER button to confirm after selecting Yes by using, button. It takes a few minutes to finalize the disc. Lock disc (DVD±RW only) You can lock your current disc to prevent further editing or recording to the disc. Lock disc by using or button. It takes ~ minutes to lock the disc. If the disc is locked, you can not make any changes any more except play it back. The FINALIZE function only works once in DVD±R disc. If a DVD±R has been finalized, you can not record or edit the DVD±R any more. If you want to unlock the locked disc, select Unlock disc by using or button. Press ENTER button. It takes a few minutes to unlock the disc. Copy All (DVD±RW/DVD±R) You can copy all titles from DVD to HDD. Copy All by using or button. It starts to copy all titles from DVD to HDD. Editing 9

40 Editing Editing a title of DVD±RW or DVD±R Play title (DVD±RW/DVD±R) You can play back the selected title. Insert a recorded DVD±RW or DVD±R disc on the disc tray. The menu screen is displayed automatically. Play title by using or button. It starts to play back the selected title. Select one title to edit by using or button. Press button, the Title Edit menu will show on the screen. Edit title (DVD±RW/DVD±R) Edit title by using or button. It starts to play back and the pop-up menu will show on the screen. <DVD±RW> - Select an available title Select to choose an available title by inputting numbers. <DVD±R> - Select an available chapter Select to choose an available chapter by inputting numbers. - Play Control playback by various setting such as Fast forward, Fast reverse, Slow. - Chapter marker You can insert a chapter or delete it. Press ENTER or button, the pop-up menu will show on the screen. 0 Editing

41 Editing To insert a new chapter marker, select Insert marker by using or button. You can search a scene by using, or PLAY button. Press ENTER button at the point where you would like to insert a new chapter. Rename title (DVD±RW/DVD±R) Rename title by using or button. The keyboard will show on the screen. To delete a chapter marker, select Delete marker by using or button. You can search the chapter by using or button. Press ENTER button at the chapter where you would like to delete. To delete all chapter markers, select Delete all markers by using or button. Press ENTER button to confirm it. Select a letter which you want to input by using,,, button, and press ENTER button to confirm it. -5 Hide chapter/unhide chapter It is a useful function to hide commercials. Select Hide chapter by using or button, and press ENTER button. If current chapter is the hidden chapter, Unhide chapter is displayed on the menu instead of Hide chapter. In this case, you can unhide the chapter by pressing ENTER button after selecting Unhide chapter. Repeat step. The maximum length of the disc name is 9 characters. The control bars of the bottom line in the keyboard is for edit command. If the inputting of letters is finished, press ENTER button after selecting OK. -6 Index picture You can change the thumbnail for the selected title. Press ENTER button at the point where you prefer to be the thumbnail. -7 Split title (DVD±RW only) You can divide the current title to titles. Press ENTER button at the point where you would like to divide. It takes a few minutes to divide the title. -8 T-Elapsed You can see the elapsed time. Press STOP button after finishing to edit the title. It takes a few minutes to update the disc. Editing

42 Editing Erase title (DVD±RW only) Erase title by using or button. The pop-up menu will show on the screen. Overwrite title (DVD±RW only) Overwrite title by using or button. It will be changed from DVD mode to AV input mode. Press AV IN button to choose the A/V input you want to record. Every time this button is pressed, A/V input is changed : Press ENTER button to erase the contents of a title after selecting Yes by using, button. It takes a few minutes to erase the title. The Erase function only works on DVD±RW discs. If you want to record the TV program, select the TV mode. And choose the station you want to record by pressing CHANNEL or CHANNEL + button. Press REC button to start your recording. It starts to record from the beginning of the current title. Press STOP button to stop your recording. The recorded programs will be erased from the beginning for recording time. Editing

43 Editing Append title (DVD±RW/DVD±R) You can record on the last title continously. If you do not select the last title this menu will not be displayed on the screen. Append title by using or button. It will be changed from DVD mode to AV input mode. Copy title (DVD±RW/DVD±R) You can copy a title from DVD to HDD. Copy title by using or button. It starts to copy a title from DVD to HDD. Press AV IN button to choose the A/V input you want to record. Every time this button is pressed, A/V input is changed : If you want to record the TV program, select the TV mode. And choose the station you want to record by pressing CHANNEL or CHANNEL + button. Press REC button to start your recording. It starts to record. Press STOP button to stop your recording. If there is no space on the disc, this menu will not be displayed on the screen. Editing

44 Editing Editing the title of HDD Press HDD/DUB button to select the HDD mode. The title list of HDD appears on screen. Select the title to edit by using or button, and press button. The edit menu appears on screen. Split You can divide the current title to titles. Split by using or button. It starts to play back the current title. Find the point where you would like to split. You can search a scene by using, or PLAY button. Press ENTER button at the point where you would like to split. The pop-up menu will show on the screen. Press ENTER button to confirm after selecting OK by using or button. Play You can play back the selected title. Play by using or button. It starts to play back the selected title. Delete Delete by using or button. The pop-up menu will show on the screen. Press ENTER button to delete the title after selecting Yes by using or button. Editing

45 Editing Segment You can skip the parts you mark when the title is played back. 5 6 When the title with segments is copied from HDD to DVD, the segments are not copied to DVD. Combine You can combine two titles. Segment by using or button. The title will automatically start playing back. Find the beginning of a segment where you would like to skip. You can search a scene by using, or PLAY button. Press ENTER button at the beginning of a segment where you want to skip. Find the end of a segment where you want to skip, and press ENTER button at the end of a segment. If you want to mark more segments, repeat step &. The marked segments are displayed as the violet colored bars on the progress bar. Press STOP button if it is finished. Combine by using or button. Select the title to be combined by using or button, and press ENTER button. (If you want to cancel, press RETURN button.) Change Index Picture You can change the thumbnail for the selected title. 5 Change Index Pic by using or button. The title will start playing automatically. Press ENTER button at the point where you prefer to be the thumbnail. (You can search a scene by using, or PLAY button.) The pop-up menu will show on the screen. Press ENTER button to confirm after selecting OK by using or button. Rename You can change the name of title. Rename by using or button. The Keyboard will show on the screen. Press ENTER button to delete the current name after selecting Clear button on the Keyboard. Select a letter which you want to input by using,,, button, and press ENTER button to confirm it. Repeat step. The maximum length of the name is upto characters. OK button on the keyboard if the inputting of letters is finished. This function is not available when the preview type in the setup menu is set to Dynamic. Editing 5

46 Editing Lock You can lock the title so that anyone can not play it. Lock by using or button. The title will be locked. Unlock You can unlock the locked title. Unlock by using or button. The password window will be displayed on TV screen. Enter the password in digits by using 0 to 9 button. Press ENTER button to confirm after selecting OK by using button. The title will be unlocked. Protect You can protect the title from editing. Protect by using or button. The title will be protected. You can play the protected title, but you can not edit it. Unprotect You can unpretect the protected title. Unprotect by using or button. The protected title will be unprotected. 6 Editing

47 Using the Setup Menu Once the initial settings have been completed, the DVD recorder can always be operated under the same conditions whenever the power is switched on. These settings are called SETUP data that are easily modified and stored using the SETUP menu. Record & Channel Scan ( ) Basic Operations Press SETUP button during stop mode. And use,,, and ENTER, RETURN button to navigate and select options. The current setting for any option is marked with a colored box. 5 Press STOP button, if the disc is being played. To call the SETUP menu, press SETUP button. Select the desired item by using or button, then press ENTER button. Select the desired sub item by using,,, and ENTER button. If you want to go the previous menu, press RETURN button. Press SETUP button after you have made all settings. Depending on the disc, some setup menu selections may not work properly. AUTO CHAPTER MARKER When Auto Chapter Marker is set to 5 min, chapters are created automatically within a title at five-minute intervals. Chapters can also be added or removed manually through the Editing features. For details, see section Editing a title. RECORD QUALITY The record quality offers 6 quality level : HQ : High Quality, you can record for up to hour in a blank disc. SP : Standard Play, you can record for up to hours in a blank disc. SP+ : Extended SP, you can record for up to hrs 0 min in a blank disc. LP : Long Play, you can record for up to hours in a blank disc. EP : Extended Play, you can record for up to hours in a blank disc. SLP : Super Long Play, you can record for up to 6 hours in a blank disc. Using the Setup Menu 7

48 Using the Setup Menu ANALOG CHANNEL SCAN This recorder has a built-in TV tuner for recording TV programs. SCAN by pressing or button. Press ENTER button to confirm after selecting OK by pressing or button. It will search channels automatically. If the broadcasting is found during auto searching, it is stored automatically. While doing Channel Search, it will erase and replace all previously stored channels. This feature is available only when the recorder is set to the TV mode. - MODIFY CHANNEL (If there is no captured channel, this feature is not available.) EDIT by pressing or button. The information of the current channel will show on the screen. Editing the channel name Name by using or button. Input letters which you want to input by using,,, button, and press ENTER button to confirm it. TV Standard Set the TV system used for the current channel. Select Standard by using or button, and press ENTER button. Select the TV system by using or button, and press ENTER button. Search Type If the captured signal is bad, you can search the channel again by frequency or channel number. Select Search Type by using or button, and press ENTER button. Select Frequency or Channel by using or button, and press ENTER button. Select Frequency or Channel by using button, and press or button. It starts to search the broadcasting automatically. If the broadcasting is found during searching, it stops to search. If you want to stop searching, press STOP button. Fine Tuning - Select the channel you want to modify by pressing CHANNEL - or CHANNEL + button. If the captured signal is not good, you can tune the channel fine. Select Fine Tuning by using or button. Tune the channel fine by pressing or button. Each time or button is pressed, the channel frequency decreases or increases by 50KHz. 8 Using the Setup Menu

49 Using the Setup Menu Decoder If the current channel is scrambled, requiring a Canal+ decoder connected to the EURO A/V IN connector, set this to On. Delete If you want to delete a captured channel, select Delete by using or button, press ENTER button. - OK using button if all the settings are correct. This feature is available only when the recorder is set to the TV mode. 5 Select a preset station to swap using or button, and press button. Select the position to insert it using or button, and press button. If you want to swap more presets, repeat step to. OK using button if it is finished. 5 CHANNEL SWAPPING (If there is no captured channel, this feature is not available.) This feature lets you swap the channel assignments of different programs. This is so that you can group together station presets which naturally go together. SWAP by pressing or button. 6 7 This feature is available only when the recorder is set to the TV mode. TIMER RECORDING See section Timer Recording. COUNTRY SELECTION your country using or button. Using the Setup Menu 9

50 Using the Setup Menu Video ( ) P-SCAN/HDMI OUTPUT When viewing Progressive Scan TV via Y/Pb/Pr connector, set to P-Scan/HDMI. When you also watch the TV via HDMI, set to P-Scan/HDMI. (This feature is not available when EURO AV output is set to RGB.) VIDEO OUTPUT FORMAT Set up Video Output Format according to type supported by your TV or monitor. If your TV is for PAL, set to PAL. If your TV is for NTSC, set to NTSC. TV ASPECT RATIO If you have a widescreen TV, select the 6:9 Wide setting. The widescreen DVD disc is shown using the full screen area. When playing the DVD disc recorded in conventional format(:), the settings on your TV will determine how the material is presented. (See the manual that came with your TV for details on what options are available). If you have a conventional TV, choose either : Letter Box or : Pan Scan. In Letter Box mode, the widescreen DVD disc is shown with black bars at the top and bottom of the screen. Pan Scan chops the sides off widescreen material to make it fit the : screen (so even though the picture looks larger on the screen, you are actually seeing less of the movie). SCREEN SAVER If a bright picture does not move for a long time, the TV may be damaged. If this state is continued on longer than 5 minutes, the screen saver works when ON is selected. The screen saver protects the CRT (Cathode Ray Tube) from damage by displaying a moving DVD logo continuously on the screen. The monitor screen of a projector or projection TV is easily burned out if a static picture is displayed for a long time. Be careful not to allow the monitor screen to be burned out when you set the SCREEN SAVER mode to OFF. Some disc will not allow you to change the aspect ratio. 50 Using the Setup Menu

51 Using the Setup Menu Audio ( ) (This menu is not available when a disc is in the recorder.) Language ( ) ANALOG OUTPUT (Not available to change) DIGITAL (SPDIF) OUTPUT RAW (Bit Stream) : The original audio stream recorded on the disc is outputted through the digital audio out connector. LPCM : The decoded audio stream is outputted through the digital audio out connector. LPCM OUTPUT You only need to make this setting if you connected this recorder to an AV amplifier (or other component) using the digital audio output. If your AV amplifier (or other connected component) is compatible with high sampling rate audio (96KHz), set to LPCM 96KHz, otherwise set to LPCM 8KHz. OSD LANGUAGE This item is used to select the language for On-Screen Display messages that will be displayed on the TV screen. When your desired language is selected, all OSD messages are displayed in the selected language. AUDIO LANGUAGE Set this value to the preferred audio language. If an audio language is selected, whenever you start playing a new disc, the selected audio language is played(if the selected language is contained in the disc). SUBTITLE LANGUAGE Set this value to the preferred subtitle language. If a subtitle language is selected, whenever you start playing a new disc, the selected subtitle language is played(if the selected language is contained in the disc). DISC MENU LANGUAGE Set this value to the preferred disc menu language. If a disc menu language is selected, whenever you start playing a new disc, the selected disc menu language is played(if the selected language is contained in the disc). Using the Setup Menu 5

52 Using the Setup Menu Clock ( ) General ( ) Automatic clock setting Some TV channels broadcast time signals together with the program. This recorder can use these signals to set the clock automatically. Date-Time Setting by using or button. Auto. Program by using button. Select the preset channel that broadcasts a clock signal, and press ENTER button. Manual clock setting If no station in your area are broadcasting time signals, you can set the clock manually. Date-Time Setting by using or button. Manual. Parental Lock This function is to disable the playing of specified DVD discs that are unsuitable for children. There are a total of 8 levels. If the level is 8, the contents of the disc are suitable for adult. If the level is, the contents of the disc are suitable for children. Used to adjust the level of parental lock. Once selected, whenever you play a disc, the selected rating level is compared to the level on the disc. If the level you selected is greater than the level of the disc, you may play the loaded disc. If not, you may not play the disc. To set appropriate rating level, do the following instructions. the proper rating level by using or button. The password window will be displayed on TV screen. Enter the current password in digits by using 0 to 9 button, then press ENTER button. If you have not changed the password, enter 0, 0, 0, 0. Enter the date & time by using 0 to 9 or,,,, ENTER button. Use 0 to 9, button to change the value in the highlighted field. Use, button to move from one field to another. Press ENTER button to confirm after selecting OK by using button. 5 Using the Setup Menu

53 Using the Setup Menu CHANGE PASSWORD Change Password. The password window appears on TV screen. 6 PREVIEW TYPE You can select the preview type of the title on the HDD title list. Static : It shows the preview with a still picture. Dynamic : It shows the preview with moving pictures. 7 HDD to DIsc Copy Option When copying from HDD to DVD, you can select the copying mode. 5 Enter the current password in digits by using 0 to 9 button, and press button. Enter the new password in digits by using 0 to 9 button, and press button. Re-enter the new password for verify, and press button. OK. The password will be changed. Fit to Disc : The recording quality is automatically adjusted so that the selected titles fit on to the space available on the disc. High Speed : The selected titles is copied at the same recording quality as the original. Highest Speed : The selected titles is copied at the specified recording quality in real-time. (Note that although you copy at a higher quality setting than the original, the copy will not be better quality than the original.) FACTORY RESET Returns the DVD Recorder back to factory default settings. Factory Reset by pressing button. A pop-up window appears on TV screen. OK. EURO AV OUTPUT Set to YCbCr to view in component video via Y/Cb/Cr connector. When using AV Euro connector RGB signal, set to RGB. 5 DECODER If you want to watch the scrambled channels, requiring a Canal + decoder connected to the EURO AV IN connector, set this to ON. Using the Setup Menu 5

54 Using the Setup Menu HDD ( ) 5 6 Timeshift buffer length When doing the timeshift recording, you can select the capacity of HDD buffer in which a TV program is stored temporarily. Timeshift buffer mode. Refresh : The content of the buffer is erased upon changing the TV channel. Preserve : The content of the buffer is maintained though the TV channel is changed. Hard disc Info It shows the information on HDD. Space Management Automatic : when the HDD is full, the recorder will overwrite un-protected titles. Manual : when the HDD is full, the recorder does not overwirte and it asks for erasing some titles to allow further recording. Format HDD You can erase all programs on HDD. Erase optical disc You can erase all programs on disc. (This function is available only when the recorder is set to the external AV mode or the TV mode.) 5 Using the Setup Menu

55 Additional Information Specifications General Recording Timer Input/ Output Euro AV connectors (-pin connector) S-Video input / output Video input / output Component video output Audio input / output Digital audio output DV input / output USB input HDMI output Audio characteristics Accessories Supported disc types Supported video formats TV system Power requirements Power consumption Weight Dimensions Operating temperature Operating humidity Recording format Recordable media Programs Clock Power off memory AV connector input / output x AV connector output x Input / Output level Input x, Output x Input / Output level Input x, Output x Output level (Y, Cb/Pb, Cr/Pr) Y (luminance) C (color) Output level Input (L/R) x, Output (L/R) x Optical digital output x Coaxial digital output x IEEE 9 standard USB. Type A x Frequency response S/N ratio Dynamic range Total harmonic distortion Audio/Video cable RF Cable Scart Cable Remote control unit "AA" size batteries Operating Instructions DVD, CD-DA, CD, CD-R/CD-RW, DVD±R/RW, DVD-R/RW MPEG-, MPEG-, MPEG-, JPEG PAL / SECAM AC 00 V-0 V, 50/60 Hz 5 W.5 kg 0(W) x (H) x 6(D) mm 5 C to 5 C 0 % to 75 % (no condensation) DVD VIDEO DVD±R, DVD±RW, HDD(60GB) 8 Programs Quartz lock (-hour digital display) Approx. hour 0 min. This connector provides the video and audio signals for connection to a compatible color TV or monitor..0 Vp-p (75 Ω) 0.86 Vp-p (75 Ω) S-VIDEO jack.0 Vp-p (75 Ω) RCA jack Y:.0 Vp-p (75 Ω) Cb/Pb, Cr/Pr : 0.7 Vp-p (75 Ω) Vrms ( khz, 0 db) RCA jack Optical digital jack RCA jack pin pin 80p / 576p Hz to khz (DVD fs: 96 khz) 00 db 95 db 0.0 % Note : The specifications and design of this product are subject to change without notice, due to improvement. Additional Information 55

56 Additional Information Troubleshooting Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified after checking the items below, ask your nearest authorized service center or your dealer to carry out repair work. Problem The disc is ejected automatically after loading. Disc not seated properly in the disc guide. Incompatible region number. Condensation inside the recorder. Disc is loaded upside down. Picture playback stops and the operation buttons cannot be used. New settings made in the Setup screen menus while a disc is playing are ineffective. Settings are canceled. No picture / No color The DVD recorder cannot record. Screen is stretched or aspect does not change. Picture disturbance during playback or dark. Dirty or damaged disc Align the disc properly. Solution If the region number on a DVD-Video disc does not match the number on the player, the disc cannot be used. Allow time for condensation to evaporate. Avoid using the recorder near an airconditioning unit. Reload the disc with the label side face up. Switch the power off once using the front panel STANDBY/ON button and then switch on again using the front panel STANDBY/ON button. Disconnect the power plug and reinsert it back into the wall. Some settings can be changed while a disc is playing, but are not effective until the disc is stopped then restarted. This is not a malfunction. Make the same setting when the recorder is stopped. When the power is cut due to power failure or by unplugging the power cord, settings will be canceled. Incorrect video connections. Check that connections are correct and that plugs are inserted fully. TV/monitor or AV amplifier settings are incorrect. Check the instruction manual of the connected equipment. The Component output menu is set to progressive but your TV/monitor is not compatible with progressive scan. Reconnect the recorder to your TV using a composite or S-Video cord and set the TV to appropriate input. The type of the disc is wrong, it's not a DVD±RW or DVD±R disc. The disc is recorded fully. The DVD±R has been finailized. The TV aspect ratio setting in the Setup menu is incorrect. Set the TV aspect ratio option to match the TV/monitor you re using. This recorder is compatible with Macro-Vision System copy guard. Some discs include a copy prevention signal, and when this type of disc is played back, stripes etc., may appear on some sections of the picture depending on the TV. 56 Additional Information

57 Additional Information Problem The remote control doesn't seem to work. No audio, or audio is distorted. The analog audio is OK, but there appears to be no digital audio signal. Noticeable difference in DVD and CD volume. No DTS audio output. Solution The remote control is too far from the recorder, or the angle with the remote sensor is too wide. Use the remote within its operating range. The batteries are exhausted. Put in new batteries. Some DVD discs do not output digital audio. Switch your amplifier to the recorder s analog outputs. Dirt, dust, etc. on the disc. Clean the disc. Interconnects are not fully inserted into the terminals (or are not connected). Check that all interconnects are firmly inserted. Dirty or oxidized plugs/terminals. Clean the plugs/terminals. Incorrect audio cable connection. Check the audio connections. Recorder s output is connected to the amplifier's phono (turntable) inputs. Connect to any set of inputs except phono. The disc is paused. Press PLAY button to exit the pause mode. Incorrect amplifier settings. Check that the volume is turned up,that the speakers are on, the input function set correctly, etc. Incorrect Audio menu settings. Make sure that the Digital Audio Out setting is set to LPCM or RAW. Check that the LPCM or RAW settings are suitable for your amplifier -check the amp s instruction manual. DVDs and CDs use different recording methods. This is not a malfunction. If this unit is connected to a non-dts compatible amplifier or decoder using a digital audio cable, please connect to a DTS compatible amplifier or decoder. If you do not do this, noise will be output if you try and play a DTS disc. If this unit is connected to a DTS-compatible amplifier or decoder using a digital audio cable, check the amplifier settings, and that the cable is properly connected. Static electricity or other external influences may cause malfunctioning of this unit. In this case, unplug the power cord and then plug back in. This will usually reset the unit for proper operation. If this does not correct the problem, please consult your nearest service center. Additional Information 57

58

59

60