GREETINGS Thank you for purchasing Indi DVD. Enjoy your new drive.

Transcription

1

2 GREETINGS Thank you for purchasing Indi DVD. Enjoy your new drive. Before installing your drive, write down its serial number. Go the following URL and register the drive: WARNING: PRIOR TO PLACING ANY DISC IN THIS DRIVE, CAREFULLY INSPECT IT TO ENSURE THAT IT IS NOT CRACKED, DEEPLY SCRATCHED OR OTHERWISE DAMAGED IN ANY WAY. USE OF A CRACKED, DEEPLY SCRATCHED OR DAMAGED DISC IN THIS OR ANY OTHER HIGH-SPEED DRIVE MAY CAUSE THE DISC TO SHATTER AND RESULT IN DAMAGE NOT ONLY TO THE DISC BUT TO THE DRIVE AS WELL. NEVER LEAVE A DISC IN THE DRIVE WHEN POWERING OFF THE COMPUTER, AS DAMAGE TO THE DISC AND POSSIBLY THE DRIVE MAY RESULT WHEN POWERING ON THE COMPUTER. FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. Any changes or modifications should be approved by the party responsible for compliance with FCC Rules. Otherwise, the user loses authority to operate the equipment. The laser beam emitted from the optical pickup is invisible. Accordingly: Do not open the optical pickup housing. Obtain service only from TDK-authorized personnel. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. LASER INFORMATION These products have been designed and manufactured according to IEC on the Safety of Laser products. This product comes under "Class 1 Laser Products." A Laser Caution Marking is attached on the top of the internal drive model: "Caution: Invisible laser radiation when open. Avoid direct exposure to beam." CAUTION: To disconnect the drive from an electrical current, pull out the AC power cord.

3 THIS PAGE LEFT BLANK INTENTIONALLY SECTION 1 : DRIVE INSTALLATION SECTION 2 : TROUBLESHOOTING AND MAINTENANCE SECTION 3 : FREQUENTLY ASKED QUESTIONS (FAQs) SECTION 4 : TECHNICAL SUPPORT WHAT INDI DVD DOES... Indi DVD is a DVD/CD burner that provides professional quality writing, rewriting and reading. SAVE YOUR BOX! If you need to ship your drive back to TDK, send it packaged in the original box (if possible). TDK cannot assume liability for any damage your drive sustains during shipment. Please ship your drive in the safest manner possible.

4 SETTING UP INDI DVD Follow the installation instructions for your computer and connection type. THIS PAGE LEFT BLANK INTENTIONALLY USB 2.0 INSTALLATION INSTRUCTIONS If your computer is a PC running Windows 2000 or XP: 1. Connect the USB cable to a USB 2.0 port on your computer and to Indi DVD s rear-panel USB 2.0 port. NOTE: Indi DVD is not USB 1.1 port compatible. The drive must be connected to either a USB 2.0 port or to an IEEE 1394/FireWire port. SECTION 1 : Drive Installation 1

5 NOTE: Refer to the Software Quick Guide for instructions on using the software. 2. Connect the power cord to Indi DVD s DC IN. 3. Connect the plug to a live power outlet. 4. Using Indi DVD s rear-panel switch, power the drive ON. 5. Open the disc tray by pressing the front-panel EJECT button. 8. Make sure that only "Specify Location" is checked and click BROWSE. An explorer window will appear. 9. Double click the drive where Disc Blender Software Suite Disc 2 is loaded. 10. Double click BONUS UTILITIES, then click HI-SPEED USB DRIVER. 11. Click OK and follow the on-screen prompts to finish installation. 12. Load Disc Blender Software Suite Disc 1 into your computer s original disc drive and reboot your computer. The software installer screen should appear. If it doesn t, double click on My Computer, double click on the drive into which you loaded Disc Blender Software Suite Disc 1, then double click SETUP.EXE. 13. Install the TDK Disc Blender Software Suite by clicking the desired programs. Follow the on- screen prompts to finish installation. NOTE: If your computer is a Mac, connect Indi DVD to the computer s IEEE 1394/FireWire port for best results. 6. Load the TDK Disc Blender Software Suite Disc 1 into Indi DVD. The software installer screen should appear. If it doesn t, double click on My Computer, double click on Indi DVD, then double click SETUP.EXE. 7. Install the TDK Disc Blender Software Suite by clicking the desired programs. Follow the on-screen prompts to finish installation. IEEE 1394/FIREWIRE INSTALLATION INSTRUCTIONS If your computer is a PC running Windows 98SE, 98ME, 2000 or XP: 1. Connect the IEEE 1394/FIREWIRE cable to an IEEE 1394/FIREWIRE port on your computer and to Indi DVD s rear-panel IEEE 1394/FIREWIRE port. If your computer is a PC running Windows 98SE or ME: 1. Load the TDK Disc Blender Software Suite Disc 2 into your computer s original disc drive. 2. Connect the USB cable to a USB 2.0 port on your computer and to Indi DVD s rear-panel USB 2.0 port. NOTE: Connecting Indi DVD to a USB 1.1 port will result in slow performance and may cause disc recording errors. Connect Indi DVD to a USB 2.0 or IEEE 1394/FireWire port for best performance. 2. Connect the power cord to Indi DVD s DC IN. 3. Connect the plug to a live power outlet. 4. Using Indi DVD s rear-panel switch, power the drive ON. 3. Connect the power cord to Indi DVD s DC IN. 4. Connect the plug to a live power outlet. 5. Using Indi DVD s rear-panel switch, power the drive ON. A New Hardware window should appear. 6. Click NEXT. 7. Check the "Search for the best driver for your device (recommended)" option and click NEXT. 2 Indi DVD ReWRITER : Hardware Guide SECTION 1 : Drive Installation 3

6 5. Open the disc tray by pressing the front-panel EJECT button. 5. Open the disc tray by pressing the front-panel EJECT button. 6. Load the TDK Disc Blender Software Suite Disc 1 into Indi DVD. The software installer screen should appear. If it doesn t, double click on My Computer, double click on Indi DVD, then double click SETUP.EXE. 7. Install the TDK Disc Blender Software Suite by clicking the desired programs. Follow the on-screen prompts to finish installation. If your computer is a Mac: 1. Connect the IEEE 1394/FIREWIRE cable to an IEEE 1394/FIREWIRE port on your computer and to Indi DVD s rear-panel IEEE 1394/FIREWIRE port. 6. Load the TDK Disc Blender Software Suite Disc 2 into Indi DVD. 7. Install the Roxio Toast Lite, if desired. ANALOG AUDIO PLAYBACK WITH INDI DVD Indi DVD has stereo (L/R) analog audio outputs, located on the drive s rear panel. Some Indi DVD models also have a front-panel headphone port. By default, Indi DVD will play audio digitally, and will not play audio through the analog audio outputs or through the headphone port. If you wish to play audio through the analog audio outputs and the headphone port, follow the steps below. To enable audio playback through Indi DVD s rear panel audio outputs (and through Indi DVD s headphone port, if applicable): 1. Double click MY COMPUTER. The MY COMPUTER Window will open. 2. Right click the Indi DVD drive and select PROPERTIES. The PROPERTIES window will open. 3. Click the HARDWARE tab. A list of all disc drives will appear. 4. Click to highlight the Indi DVD drive. 5. Click the PROPERTIES button. The Indi DVD PROPERTIES window will open. 6. Click the PROPERTIES tab. 7. Uncheck the ENABLE DIGITAL CD AUDIO FOR THIS CD-ROM DEVICE checkbox. 8. Click OK to confirm and close the window, then click OK to close the previous window, if applicable. 9. Run AudioCentral. 10. Click TOOLS and select OPTIONS. The AudioCentral options window will open. 11. Click the CD OPTIONS tab. 12. Under PLAYBACK SETTINGS, select ANALOG. 13. Click APPLY, then click OK to confirm and close the window. NOTE: Some (not all) Indi DVD drives feature a front-panel headphone port. The same steps described in this section should be used to enable CD audio playback through Indi DVD s front-panel headphone port. NOTE: When the ENABLE DIGITAL CD AUDIO FOR THIS CD-ROM DEVICE checkbox is unchecked, digital playback (i.e. playback through the drive s data cable) to your computer s speakers is not possible. 2. Connect the power cord to Indi DVD s DC IN. 3. Connect the plug to a live power outlet. 4. Using Indi DVD s rear-panel switch, power the drive ON. NOTE: If your Indi DVD drive has a headphone port and a front-panel volume knob, note that the knob only controls the headphone port s volume and does not affect Indi DVD s rear-panel audio output level. 4 Indi DVD ReWRITER : Hardware Guide SECTION 1 : Drive Installation 5

7 THIS PAGE LEFT BLANK INTENTIONALLY IF INDI DVD DOES NOT FUNCTION: Connecting Indi DVD to a USB 1.1 port will result in slow performance and may cause disc recording errors. Connect Indi DVD to a USB 2.0 or IEEE 1394/FireWire port for best performance. Verify that Indi DVD is connected to a functioning power outlet. If Indi DVD is connected to a PC s USB 2.0 port, verify that the Hi-Speed USB 2.0 PC driver is properly installed. IF INDI DVD WILL NOT RECORD PROPERLY: Verify that Indi DVD supports the recordable media format to which you re attempting to record. Verify that the recordable media you re using is rated to record at the desired speed. Verify that the recordable media is inserted into Indi DVD with the correct orientation. (Media should be placed label side up in the disc tray.) Since low quality media may not record properly, it s best to use TDK discs. Verify that the drive is not connected to a USB 1.1 port. Indi DVD is not USB 1.1 port compatible, due to bandwidth limitations. A buffer underrun may have occurred. Either select a slower recording speed or select using Buffer Underrun Protection in your software. Inadequate system RAM can sometimes cause buffer underrun errors. Disable all other functions and applications that could interrupt the stream of information. Make sure that the media does not have any fingerprints, dirt or scratches on the surface. Check to see if the disc already has data written on it. If the disc is rewritable, you can erase and re-record it. Use the recording software supplied with Indi DVD. Some other software may not be supported. The included software does not enable making copies of commercial DVD movie discs, such as those rented from your local video store. Always respect intellectual property laws. 6 indidvd ReWriter : Hardware Manual SECTION 2 : Troubleshooting & Maintenance 7

8 IF INDI DVD CAN T CREATE A MULTI-SESSION DISC: There may not be enough space left on the disc, including the lead in and lead out for each session. Make sure that the disc wasn't previously finalized. If the disc was finalized, additional recording on the disc will not be possible. IF INDI DVD CAN T READ A DISC AFTER A SUCCESSFUL BURN: See if another compatible drive can read the disc. If the disc can t be read, the directory information may be corrupt. When setting up a recording session, select Finalize in the recording software. If the disc isn t finalized, that may be the problem. IF A DISC WILL NOT EJECT FROM INDI DVD: Shut down the computer, power Indi DVD OFF, power Indi DVD back ON and press its EJECT button. If that doesn t work, carefully insert a straightened paperclip into Indi DVD s emergency eject hole, located on the drive s front panel. IF YOU CAN T SUCCESSFULLY VIEW DVD VIDEOS: Your computer s system specifications may be a major factor. If your video card is outdated or low-end, it could be the problem. Inadequate system RAM is another likely culprit. Verify that DVD playback software is installed on your computer. Refer to the Indi DVD product packaging or to for recommended system specifications for optimal performance. IF YOUR COMPUTER PERFORMS POORLY WHEN EDITING VIDEO: Your computer s system specifications may be a major factor. Video editing is processor and RAM intensive. Other factors, such as your video card may contribute to the problem. Refer to the Indi DVD product packaging or to for recommended system specifications for optimal performance. IF VIDEO RENDERING TAKES A LONG TIME: Even on high-end computer systems, video rendering is a time consuming process. Upgrading your computer may shorten rendering times, but there isn t a magic fix. IF INDI DVD IS CONNECTED TO A FIREWIRE PORT, BUT DOESN T APPEAR ON THE MAC DESKTOP (MAC USERS ONLY): The MacOS does not mount drives on the desktop; it only mounts volumes (discs). Try putting a disc with something on it into the drive and see if it shows up on the desktop. If a disc does not show up on the desktop, verify that there are no more than 63 devices plugged in with no more than 16 hops between any two devices. If you have problems during or right after installation of your Indi DVD drive, use these tips to help find the problem. What media should I use for my Indi DVD? See the included specifications sheet or visit for more information. When should I record to DVD media? Recordable DVD discs have much higher capacity than CD-R/RW discs. This makes recordable DVD discs ideal for recording video and large multimedia files and for backing up your hard drive. Why can t I do disc-to-disc copying? Some possible reasons are: Some CD-ROM and DVD-ROM drives will not allow direct copying to Indi DVD, or are not capable of digital audio extraction. You must use either a SCSI-2 drive or a supported ATAPI drive as the source. Some discs have copy protection or other features that prevent disc-to-disc copying. You cannot copy commercial DVD discs or copy protected CD discs. Why am I getting buffer underrun errors? If available, your recording software s buffer underrun write assurance option should be activated. Buffer underrun errors can occur if another application interrupts the writing process, or if the recording drive s write speed is set too high for the speed at which the source drive can supply data. Lack of computer memory can also cause underrun errors. How can I optimize the recording process? Make sure your system meets the minimum system requirements. Do not run other applications while recording discs. Log off any networks, disable any FAX modems, , screen savers, or other programs that may send messages to your computer while it is writing a disc. If your computer has a power management feature, disable it. Run ScanDisk and Disk Defragmenter periodically on your hard drive. Do not record using data from a compressed hard drive. Buffer underruns may be caused by hard drive compression software. What is the best way to label a disc that I just burned? With a CD/DVD labeling marker. The marker must be soft-tipped and either alcohol or water based. Markers of other types will ruin the disc. Another way is to use a good quality label maker, such as TDK s CD/DVD Labeling System. 8 Indi DVD ReWRITER : Hardware Guide SECTION 3 : Frequently Asked Questions 9

9 THIS PAGE LEFT BLANK INTENTIONALLY Keep TDK s , Web site, and phone numbers in a convenient location as indicated below. Keep your drive s serial number and a copy of your sales receipt handy as well. If you experience a problem while installing or operating your Indi DVD, please refer first to the relevant sections of this manual regarding setup and installation. If you do not uncover the solution there, please refer next to the Troubleshooting chapter. It contains solutions to the most common types of problems fielded by our technical support staff. You may also wish to refer to the Frequently Asked Questions (FAQ) section of our Web site to assist you in troubleshooting the problem on your own. If you have not been successful in your quest, our Technical Support Department will help you solve problems that relate specifically to your Indi DVD. In many cases, a problem that appears to be caused by your Indi DVD actually originates in another part of your computer. In such instances, our technical support staff will try to help you identify the part at fault and will refer you to the manufacturer of that part for further assistance. HOW TO CONTACT US There are several ways for you to contact TDK s Technical Support Department. Visit our web site ( for answers to Frequently Asked Questions. BEFORE YOU CONTACT US Please gather as much of the following information as possible before contacting us. The serial number and TLA number of your Indi DVD. Your serial number can be found both on the retail box and on a label on the drive itself. The version of TDK Disc Blender Software you are using, if applicable. The latest version of firmware you loaded onto the drive, if applicable. The version of the Windows operating system you are using. NOTE: Most new CD-ROM drives can read CD-RW discs. Many older drives may not be able to read CD-RW discs. NOTE: Australian Users should call for TDK Technical Support or techsupport@tdk.com.au (continued on next page) 10 Indi DVD ReWRITER : Hardware Guide SECTION 4 : Technical Suuport 11

10 The brand name and model number of your computer (e.g. Dell Dimension 4500, Gateway 300 Series, etc.). The type of VGA, Super VGA, or other graphics card you use. Brand name and model number of any other peripherals you have installed or connected to your computer (e.g., CD-ROM, scanner, fax board, network board). RETURNS You must receive an RMA (Returned Materials Authorization) number from our Technical Support Department before any TDK drive can be returned for repair or replacement. Any drive sent to TDK without an RMA number will not be accepted. Drives must be sent postage prepaid. We recommend that you insure your shipment, as TDK cannot be held responsible for any damage that may occur during shipment. For on-line support or to contact Technical support, please visit: For registration of product, please visit: TDK LIMITED WARRANTY One Year Limited Warranty for Hardware TDK Electronics Corporation ("TDK") warrants to the end-user customer that this data storage product, exclusive of software (referred to herein as "Hardware" or "Product") will be free from defects in material and workmanship for a period of one (1) year from date of purchase. If TDK receives notice of any such defects during the warranty period, TDK will, at its option, either repair or replace the Product which it finds to be defective at no charge (except for shipping and insurance). Repair of defective Product may be with either new or rebuilt replacement parts that will be warranted for the remainder of the original warranty period. Any exchanged parts under this warranty will become the property of TDK. Replacement Product may be either new or reconditioned. If the Product is discontinued and no longer available, then it may be replaced with Product determined by TDK to be of similar value and performance. TDK DOES NOT AND CANNOT WARRANT THE PERFORMANCE OR RESULTS YOU MAY OBTAIN BY USING THE TDK BRANDED SOFTWARE, MEDIA OR DOCUMENTATION.TDK MAKES NO WARRANTIES, EXPRESS OR IMPLIED, AS TO NONINFRINGEMENT OF THIRD PARTY RIGHTS, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Any software other than TDK Software included with the Product is supplied on an AS IS basis and without any representations or warranties of any kind, whether express or implied, including but not limited to the implied warranties of merchantability, fitness for a particular purpose, title and non-infringement. Please refer to any documentation included with such software for your rights and obligations with respect to that software. TDK does not warrant that the operation of the Product will be uninterrupted or error free. This Limited Warranty does not apply to defects resulting from (1) acts of God, accident, misuse, abuse, negligence, abnormal, or unusually heavy use; (2) improper installation, operation, testing, or maintenance; (3) power failure or connection to improper voltage supply; or (4) attempted repair by any party other than TDK. This Limited Warranty does not apply when the malfunction results from the use of the Product in conjunction with other products, software, or accessories, or where it is determined by TDK that there is no fault with the Product itself. This Limited Warranty is invalid if the factory applied serial number has been altered or removed from the Product. This Limited Warranty extends only to the original end-user customer and is not transferable to any subsequent purchaser. This Limited Warranty is valid only within the United States. For areas outside the United States, contact the authorized dealer from whom you purchased the Product to determine what warranty, if any, applies. In order to obtain warranty service, you must deliver the Product to TDK freight prepaid, in either its original package or packaging providing a degree of protection equivalent to that of the original packaging, along with proof of purchase. [Please contact TDK at the number listed below or in the manual for further information.] TDK MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT THAT ANY IMPLIED WARRANTIES APPLY, DESPITE THEIR EXCLUSION UNDER THIS LIMITED WARRANTY, SUCH WARRANTIES SHALL BE LIMITED TO THE DURATION OF THE EXPRESS WARRANTIES PROVIDED HEREUNDER. THE REMEDIES PROVIDED UNDER THIS LIMITED WARRANTY ARE THE SOLE AND EXCLUSIVE REMEDIES. TDK S LIABILITY UNDER ANY LEGAL THEORY FOR ANY LOSS OR DAMAGE IN ANY WAY RELATED TO THE PRODUCT SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. IN NO EVENT SHALL TDK BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM USE OF THE PRODUCT. Some states do not allow limitations on how long an implied warranty lasts or any exclusion or limitation on incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may have other rights that vary from state to state. 12 Indi DVD ReWRITER : Hardware Guide TDK Electronics Corp. 901 Franklin Ave., Garden City, NY SERIAL NUMBER